We found the following complaints for OLDSMOBILE 88 (1999)
Read complaints for OLDSMOBILE 88 (1999)
While traveling on a 4-lane highway at 55 mph drivers side airbag suddenly deployed.consumermanaged to make it to the side ofroad.there were no bumps inroad that could have caused airbag to suddenly deploy.consumer has contacted dealer.dealer has not found a solution.please provide any further information.
1999 oldsmobile 4.8l engine will shut completely off unexpectedly while driving. This occurs both at highways speeds of 65 mph or at slower speeds of 35 or 35 mph. All of the power assisted features such as power brakes and steering also stop working when the engine stops.the engine shutting defect does not occur daily and is unpredictable. The only check engine code present was a "egr valve" code. The egr valve was replaced at the cost of $344.00. The engine shutting off unexpectedly defect has continued to occur after the check engine repair was completed.this is an extreme safety issue that appears to replicate the gm ignition switch recall that this vin is not included in. From "googling" this defect it appears to affect a large number of similar vehicles with 3.8l gm engines and electrical systems.
Vehicle will randomly "kill" and it happens sporadically - also possibly something in the electrical system is failing - many different issues with reference to electrical problems.
While travelingand without any indication vehicle lostpower. Dealership serviced vehicle, and noticed engine was locked. Technician replaced spark plugs, manifold, and starter.
The vehicle's rear power window wire harness caught fire without warning. The cause has yet to be determined. Please provide additional information.
The battery was replaced by the dealer twice, due to leaking.*scc
1) rough idle when stopping car. Upon restart,strange noise from engine.would not restart. 2)smoke from starter.engine locked up.water loss from radiator. Cracked manifold. 3) replaced upper intake manifold & gasket.cleaned lower intake.replaced spark plugs & wires. Changed oil, oil filter, & replaced starter.
While travelingand without any indication vehicle lostpower. Dealership serviced vehicle, and noticed engine was locked. Technician replaced spark plugs, manifold, and starter.
After starting the vehicle a fire started under the hood. Fire was extinguished, and vehicle was towedto dealership, butdealership did not resolve the problem.
Complete loss of dash lighting.intermitent lost of instrument digital indicators i.e. Mileage, transmission indicator and radio/clock readout."factory trained personnel" beat on dash and pulled on wires both times along with complete disassembly of dash board.both times the lights started working on their own.we are beginning to experience failure with intermitent lost of lights and digital indication again.dealer wants to wait until they go out completely.hazard exist when driving expecially at night with no dash lights or indicators.
Owner tried to start car and there was a popping noise from under the hood. Vehicle would not start, and smoke came from under vehicle due to the engine catching on fire. Dealer has seen vehicle.
The contact owns a 1999 oldsmobile 88.the contact stated that while traveling 55 mph, the check engine warning light illuminated as the engine overheated. The vehicle was towed to the dealer who confirmed that the failure was caused by a hole that had melted in the intake manifold, causing coolant to leak into the manifold. The manufacturer was not contacted. The vehicle was repaired. The failure mileage was 72,602 and the current mileage was 73,102.
1999 oldsmobile 4.8l engine will shut completely off unexpectedly while driving. This occurs both at highways speeds of 65 mph or at slower speeds of 35 or 35 mph. All of the power assisted features such as power brakes and steering also stop working when the engine stops.the engine shutting defect does not occur daily and is unpredictable. The only check engine code present was a "egr valve" code. The egr valve was replaced at the cost of $344.00. The engine shutting off unexpectedly defect has continued to occur after the check engine repair was completed.this is an extreme safety issue that appears to replicate the gm ignition switch recall that this vin is not included in. From "googling" this defect it appears to affect a large number of similar vehicles with 3.8l gm engines and electrical systems.
Tried to start car to go to work in the morning of 6-16-14. Heard loud boom and smoke started pouring out from under hood. Opened hood and engine was on fire. Extinguished flames and found the intake mainifold had litterally blown apart. There was a recall that should have dealt with this problem.
Low coolent light came on. We added 1 qt. Of coolent, the lifters made noise. We had the oil changed, there was coolent in the oil. The head gasket blew the engine was ruined
Was driving my 99 olds 88 up a hill in tn and it started to shake and lose power. The check engine light came home and the engine was excessively hot. All of the radiator would take the fluid but nothing would leak out. I pulled the car over and waited for it to cool down but then after the 3rd time trying to start it, it made a clunk noise and wouldn't start any more.i was told it was a hydraulic lock up. Car sat for 5 months and finally got the money to have it towed to a collision center to have it looked at. I wish to be reimbursed after it is fixed.
The consumer heard a loud noise come from motor/ and smoke started coming from up under the hood.*mr*scc fire started while at the gas station.
1999 oldsmobile 88 plastic intake manifold cracked due to hot pipe routed near it (per the mechanic).this allowed coolant and oil into the engine.engine is making bad clanking noise. Cost to replace intake, replace plugs, new sensor was $1096.it appears from reading arfc website that this is a common problem and manufacturers defect.
Vehicle experiencing problems on plastic upholstery on arm rest, replacement of water pump and starter, plastic intake manifold, and blowing up of the engine gasket.*la*mr
1) rough idle when stopping car. Upon restart,strange noise from engine.would not restart. 2)smoke from starter.engine locked up.water loss from radiator. Cracked manifold. 3) replaced upper intake manifold & gasket.cleaned lower intake.replaced spark plugs & wires. Changed oil, oil filter, & replaced starter.
Engine failed due to a faulty upper intake manifold. The consumer stated the part was manufactured out of recycled materials and caused coolant and oil to enter the cylinders and created a hrdrostatic static.
Intermittently while driving at any speed and with out any warning vehiclestalled.also, while pulling in to a parking lot vehiclejumped forward, and the engine compartment exploded. Dealer repaired the problem, but stalling and surging stilloccur.
My oldsmobile 88 year 1999 had engine failure in 2005 with only 59,930 miles. The upper plemum desintegrated allowing coolant into the cylinders, locking up engine. No warning except rapid raise in engine temperature only about a minute to pull over into a parking lot.
I brought my car in to the dealership for an oil leak and while there the mechanic also checked the coolant level.it was low.he pressure tested the system and found the coolant cap to be not sealing properly.i paid for my repairs and left.the next morning the check engine light came on.i brought the car back to the dealership.they found the engine was misfiring.they checked the coolant level again and it was dry.the intake manifold had melted and coolant had leaked into the engine and was consumed by the engine.now i needa new intake manifold, gaskets, spark plugs, wires, and an oil change to the tune of $800+.i have searched on the internet and found many similar complaints.why does gm not do anything.the intake manifold was plastic.plastic does not belong in an engine.i hope you make them recall this.
Service mechanic said this problem with crack in plenum has been seen before by him and heard of numerous times and probable factory defect.the crack in the plenum allowed coolant into the pistons of the engine and causing the engine to throw a rod.mechanic advised us to notify nhtsa and general motors.
I experienced stalls and power surges. Dealer replaced fuel pressure regulator due to recall.six months later car reached extremely high temperature then died.mechanic replaced cracked plenum. Gaskets, pipes, assembly, seals and sensor resulting in $1234 repair bill.contacted gm and got full reimbursement as vehicle has only 37,000 miles on engine.less than 250 miles after repair, engine produces loud knocking noise and loss of power while driving home from town 90 miles from home on july 4th.mechanic says one of the pistons/rods is bad, more then likely a result of the previous problems.have not been successful in reaching the extremely helpful customer service representative i was dealing with from gm but i will not drop this!last quote for current repair was $1100.
The vehicle stalled while driving.when this occurred, the vehicle lost power steering and brakes.the vehicle was serviced several times by the dealership and the fuel pressure regulator recall 04v090000 repairs were performed, but the stalling still occurred.*scthe consumer took the vehicle to another mechanic and they that the crack shaft position sensor was bad
The vehicle caught on fire in the engine compartment.(claim#38-j819-740)
Vehicle caught fire in the engine compartment, claim 38-j819-740.
Vehicle caught on fire. Dealer has been contacted for this problem, and discovered a mouse has built a nest inengine compartment.consumer feels gm should take responsibility due to the design of the engine compartment which allowed a mouse to be able to have access to the engine department
While travelingat highway speeds vehicle will lose all power andsteering and brakes get hard. Consumer was almost rear ended becausetail lights became inoperable. Dealer has yet to be contacted. Please provide further details.
Consumer started vehicle when a pop noise was heard, vehicle caught fire in the engine compartment, claim 52-2537-313.
1999 olds, delta 88 - starts hard, engine dies [hot and cold]in motion [lower speeds] and stopping at lights.fuel pump, filter and strainer replaced.fuel pressure now in spec.check engine light never on and no codes present.problem continues [last 20 days]. *nlm
As the insured was starting the vehicle, there was a popping sound and then the vehicle caught on fire.(claim#52-2537-313)
Consumer started vehicle when a pop noise was heard, vehicle caught fire in the engine compartment, claim 52-2537-313.
Vehicle caught fire in the engine compartment, claim 38-j819-740.
I have replaced the plenum in my 1999 oldsmobile 88 twice now!!!i have a 3800 motor in it with 107,000 miles on it.i have talked to many people that have had to replace their plenums also and my mother had to change hers with 40,000 miles on her car!the plenum is made of plastic and is junk!!!gm needs to step up and take care of this problem, i have spent over $1,000 fixing this inferior part!i own 3 gm products and i will never buy another if gm does not take responsibility for this!
As the insured was starting the vehicle, there was a popping sound and then the vehicle caught on fire.(claim#52-2537-313)
The vehicle caught on fire in the engine compartment.(claim#38-j819-740)
Received recall #04v090000 concerning fuel pressure regulator. Took vehicle to dealership and had it repaired on 3/18/2005. Recall repairs failed when 4 days later, on 3/24/2005, the manifold ruptured and caused water to leak into the oil. Had not taken vehicle back to dealer.
Fuel regulator was defective, fuel remained in regulator. Turning over engine caused spark whicj blew manifold out.
Complaint received via e-mail. My car with a 3800 series 11 engine recently broke down due to a cracked upper intake plenum caused by the egr pipe. The shop performing the repairs said this was a very common problem that they have repaired often. I could understand other moving/mechanical parts that endure wear and tear failing, but this is a part that simply burned out. I like gm to stand behind this part instead offsticking consumers with a $600.00 repair bill caused by their poor design.
Automobile ruptured intake manifold. Gm then acknowledged through a recall that this was caused by a fuel pressure regulator and gm would take care of the repair bill. My olds did just this and my dealer said that the pressure regulator could cause the intake manifold to rupture. Gm refuses to help me. My vin is [xxx]. You folk should make gm take care of this.updated 07/24/2012 information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6)
While travelingand without any indication vehicle lostpower. Dealership serviced vehicle, and noticed engine was locked. Technician replaced spark plugs, manifold, and starter.
The intake manifold failed and sent coolant through the entire engine and exhaust system. The vehicle is 1999 oldsmobile 88 with 3.8 v6. Repair cost over $1,800.*la
When vehicle was started a billow of smoke emitted from the engine compartment, it was discovered that intake manifold was cracked.
Plastic intake manifold failed and sent coolant through out the engine and exhaust system resulting in a very costly auto repair. The vehicle is a 1999 oldsmobile 88 with3.8 v6.
Air conditioning failed in 1999 oldsmobile 88 in 2 places at the same time.the service manager at the dealership has never seen these types of failures in a car only 4 years old.expense to have repaired was $816.
Tire reserve load label is missing from driver's side door. Owner's manual states the label should be located on driver's door.
While travelingat highway speeds vehicle will lose all power andsteering and brakes get hard. Consumer was almost rear ended becausetail lights became inoperable. Dealer has yet to be contacted. Please provide further details.
Design placement of multi-function switch is hidden from view of the driver by the steering wheel.nlm
The vehicle's fuel pressure regulator failed.the vehicle idled fast and died.the mechanic found a fuel pressure regulator cracked and leaking.the upper intake manifold gasket was leaking and needed to be replaced. *sc
Request for compensation for engine failure as a result of a defective plastic intake manifold. *mr coolant leaked into the engine which was caused by the main bearing seizing.recall# 04v090000.the initial diagnosis was that the seal under the plastic plenum was defective.the check engine light had come on within two blocks of leaving the service dealer.they found that coolant leaked into the engine again and the warped plastic plenum would not seal against the manifold. *scthe consumer stated the vehicle needed other repairs such as a replacement motor for the passenger's window,power steering hose which was leaking, a rear wheel cylinder and a new transmission.
The fuel pressure regulator was recalled and the manufacturer replaced it with the same type of regulator which lead to a leak and allowed the fuel to leak into the intake manifold which lead to the antifreeze going into the oil causing the engine to back fire and eventually ruining the engine.provide further details.
Experienced seriousproblems with intake manifold. There was a backfire through the intake manifold which produced a loud bang and severe damage to other items in the engine compartment.the consumer believed the problem she experienced was the same as the recall that was issued.it was discovered the fuel pressure regulator was defective, however the consumers claim for reimbursement was denied.
The vehicle stalled while driving.when this occurred, the vehicle lost power steering and brakes.the vehicle was serviced several times by the dealership and the fuel pressure regulator recall 04v090000 repairs were performed, but the stalling still occurred.*scthe consumer took the vehicle to another mechanic and they that the crack shaft position sensor was bad
After the dealership performed the fuel pressure regulator recall 04v090000 the consumer continued to experience problems..
After fuel regulator replaced for recall my olds delta 88 stalls out, failing to restart. I have had it towed four times. Have had fuel pump and filter changed twice - did not solve problem. It stalls while driving, upon initial starting and at stops. This problem is "periodic" and mechanic has been unable to determine problem. Engine runs very rough, and then fails to start. Had fuel tank drained 3 times no solution yet!
When attempting to crank the vehicle the engine back fired and smoke billowed from under the hood of the vehicle.the dealer informed the consumer that the fuel pump was replaced, because when they attempted to start the vehicle it back fired and blew up the manifold, however on july 9, 2004 the consumer received a recall notice regarding the fuel pressure regulator which describe in detail in which the consumer stated sounded just like the problem he experienced.the consumer submitted a claim for reimbursement, but was denied.the manufacturer stated the part on his vehicle that was replaced was not the part that was recalled.
Problems with fuel system on 1999 oldsmobile 88. *mr there was a stronggas smell and fuel was found leaking from the top of the gas tank.the tank was removed and the fuel sender and lines were found rusted and leaking. *sc
When the vehicle was started there was a loud bang and smoke emitted from the engine compartment.the consumer opened the hood and noticed that the manifold cracked.upon further investigation at the dealer it was determined that the fuel pressure regulator leaked causing the injector to blow off the injector.this in turn caused the intake manifold to crack.the dealer replaced the upper intake manifold with gaskets along with the fuel pressure regulator and fuel rails. *ph *nlm
Problems with fuel system on 1999 oldsmobile 88. *mr there was a stronggas smell and fuel was found leaking from the top of the gas tank.the tank was removed and the fuel sender and lines were found rusted and leaking. *sc
The vehicle upper intake manifold cracked prior to receiving the recall notice. Recall number(903v473000).one day prior to receiving the recall notice the consumers vehicle became disabled.the service manager determined the problem could have been a defective fuel pressure regulator.after the regulator was replaced the engine still would not start.the consumer had the vehicle fixed at herown expense.*tc
Received recall #04v090000 concerning fuel pressure regulator. Took vehicle to dealership and had it repaired on 3/18/2005. Recall repairs failed when 4 days later, on 3/24/2005, the manifold ruptured and caused water to leak into the oil. Had not taken vehicle back to dealer.
I contacted gm bc the technical service bulletin for the fuel pressure regulator says the fuel rail also needs replaced if it is a delphi fuel rail. The regulator on this car has been changed but still has the same delphi fuel rail. The car currently has a gas leak. When i search the vin it doesn't show any recalls currently but based on the tsb. The rail should've been replaced with a bosch. I am a service tech at a private shop. If i weren't a tech i wouldn't have known the rail wasn't replaced and i may not have noticed the leak until i burnt to death in a firey crash. Gm has no answer except to take it to a dealership where they want to charge me a ridiculous diagnostics fee which i refuse to pay, especially for a recall repair that wasn't done properly the first time.
Complete loss of dash lighting.intermitent lost of instrument digital indicators i.e. Mileage, transmission indicator and radio/clock readout."factory trained personnel" beat on dash and pulled on wires both times along with complete disassembly of dash board.both times the lights started working on their own.we are beginning to experience failure with intermitent lost of lights and digital indication again.dealer wants to wait until they go out completely.hazard exist when driving expecially at night with no dash lights or indicators.
We bought this car in december, 2012 and there was no recall on the carfax report at that time.today, there is a recall # 1999011 dated 3/13/1999 for power train(transmission 4t65e manual valve link replacement) nhtsa 99v089000.this owner nor the previous owner did not receive any kind of notice for this recall.was the service performed?what happened?thank you & have a great day !!!
Request for compensation for engine failure as a result of a defective plastic intake manifold. *mr coolant leaked into the engine which was caused by the main bearing seizing.recall# 04v090000.the initial diagnosis was that the seal under the plastic plenum was defective.the check engine light had come on within two blocks of leaving the service dealer.they found that coolant leaked into the engine again and the warped plastic plenum would not seal against the manifold. *scthe consumer stated the vehicle needed other repairs such as a replacement motor for the passenger's window,power steering hose which was leaking, a rear wheel cylinder and a new transmission.
On occasional hard acceleration the vehicle shudders and does not accelerate. This has caused safety concerns when merging with traffic. It can also shudder at part throttle but that's more of an annoyance than safety issue.
Complete loss of dash lighting.intermitent lost of instrument digital indicators i.e. Mileage, transmission indicator and radio/clock readout."factory trained personnel" beat on dash and pulled on wires both times along with complete disassembly of dash board.both times the lights started working on their own.we are beginning to experience failure with intermitent lost of lights and digital indication again.dealer wants to wait until they go out completely.hazard exist when driving expecially at night with no dash lights or indicators.
Automatic transmission failure.
There is an unusual sound coming from front door when turning, andbrakes lock up.consumer states that transmission does not always engage when in reverse and forward after some stops.
Speed sensor has malfunctioned, causing abs light andtraction control light to illuminate on the dash. Consumer has contacted the dealer, replaced right front wheel hub and bearings due to water intrusion into sensor.module, electronic brkae, and traction control also replaced.*ml
There is a clunking noise inrear which occurs at any time, and is becoming worse/ louder.struts have been replaced and adjustments have been made on the gas tank, however the noise is still occurring, dealer can not find any problems.
Middle receiving part of the buckle in the middle front seat position sticks up awkwardly, making it impossible to buckle all the front seatbelts up with 3 passengers in the front seat. Also the vehicles middle front seatbelt does not fit around the occupant. Dealer cannot retrofit seatbelts.
Consumer haddriver's side lap belt checked upon purchase. Dealership told him that the lap belt should not have tension until or unless he applies the brakes at more than 30mph.
Design of driver's side safety belt cannot be properly adjusted for woman 5'2".high position places belt on chin, low position places belt on neck.nlm
Seat belt is loose. Mjs
Middle receiving part of the buckle in the middle front seat position sticks up awkwardly, making it impossible to buckle all the front seatbelts up with 3 passengers in the front seat. Also the vehicles middle front seatbelt does not fit around the occupant. Dealer cannot retrofit seatbelts.
There is an unusual sound coming from front door when turning, andbrakes lock up.consumer states that transmission does not always engage when in reverse and forward after some stops.
Brakes fade constantly.
While in stop and go traffic vehicle momentarily lost steering control and brakes for 5 or more second before control was restored, vehicle was taken to dealer for inspection,and informed consumer that nothing could be found.
Speed sensor has malfunctioned, causing abs light andtraction control light to illuminate on the dash. Consumer has contacted the dealer, replaced right front wheel hub and bearings due to water intrusion into sensor.module, electronic brkae, and traction control also replaced.*ml
Brakes failed resulting in an accident.
Brake fluid soaked rear brake linings. Dealer now says that front rotors are warped due to excessive heat and must be replaced at our expense. The rear wheel cylinders were replaced under warranty and the rear brake shoes were washed /cleaned.
Brake fluid soaked rear brake linings. Dealer now says that front rotors are warped due to excessive heat and must be replaced at our expense. The rear wheel cylinders were replaced under warranty and the rear brake shoes were washed /cleaned.
Brake fluid soaked rear brake linings. Dealer now says that front rotors are warped due to excessive heat and must be replaced at our expense. The rear wheel cylinders were replaced under warranty and the rear brake shoes were washed /cleaned.
The contact owns a 1999 oldsmobile 88.while driving 10 mph, the steering became very loose and the contact lost control.he managed to pull the vehicle over to the side of the road.there were no warnings prior to the failure.the vehicle was towed to a local repair shop and the mechanic stated that there was a sheared bolt between the rack and pinion and the subframe.the vehicle is currently being repaired at the cost of $750.the contact is in the process of notifying the manufacturer.the failure and current mileages were 130,000.
Power steering gear/rack was leaking and had to be replaced.*jg
While in stop and go traffic vehicle momentarily lost steering control and brakes for 5 or more second before control was restored, vehicle was taken to dealer for inspection,and informed consumer that nothing could be found.
Power steering gear/rack was leaking and had to be replaced.*jg
Request for compensation for engine failure as a result of a defective plastic intake manifold. *mr coolant leaked into the engine which was caused by the main bearing seizing.recall# 04v090000.the initial diagnosis was that the seal under the plastic plenum was defective.the check engine light had come on within two blocks of leaving the service dealer.they found that coolant leaked into the engine again and the warped plastic plenum would not seal against the manifold. *scthe consumer stated the vehicle needed other repairs such as a replacement motor for the passenger's window,power steering hose which was leaking, a rear wheel cylinder and a new transmission.
I noticed a few chips in the paint near the right front side of the car and hood above the drivers side, last year, about dec 2003. Now the little chips of paint are coming off with a little rain/water/driving. The rimer is still there, just the top coat is coming off. Since the car is six years old it is not covered under warranty.
Body is broken where the front sub-frame bolts to. Customer was told that there is permanent body damage to the body frame. They then sold the vehicle undisclosed the fact that the vehicle is too damaged to drive on the road safely.
The front end was vibrating. I took the car in for alignment and tire rotation and was( dot number: tire size: p205/70r15 )
1999 oldsmobile 4.8l engine will shut completely off unexpectedly while driving. This occurs both at highways speeds of 65 mph or at slower speeds of 35 or 35 mph. All of the power assisted features such as power brakes and steering also stop working when the engine stops.the engine shutting defect does not occur daily and is unpredictable. The only check engine code present was a "egr valve" code. The egr valve was replaced at the cost of $344.00. The engine shutting off unexpectedly defect has continued to occur after the check engine repair was completed.this is an extreme safety issue that appears to replicate the gm ignition switch recall that this vin is not included in. From "googling" this defect it appears to affect a large number of similar vehicles with 3.8l gm engines and electrical systems.
The first time i put the car in the shop is because i was driving at about 45 mph and the car shut off on me while entering the freeway. The second time was because the car wouldn't start until after 15 min or so. I have paid $650 for my ignition switch to be changed $280 for the key lock cylinder with key changed, and $1150 for new head gasket after car over heated cause the plastic manifold gasket melted and cracked causing the car to overheat. I have done all of this within a year and the crazy thing is the car isn't starting again. I really think you all should consider a recall on this car because im wasting money on a car i never get to drive even after i pay for the costly repairs.
Vehicle experiencing problems on plastic upholstery on arm rest, replacement of water pump and starter, plastic intake manifold, and blowing up of the engine gasket.*la*mr
Vehicle has experienced two occasions of sudden acceleration. Mjs
Speed sensor has malfunctioned, causing abs light andtraction control light to illuminate on the dash. Consumer has contacted the dealer, replaced right front wheel hub and bearings due to water intrusion into sensor.module, electronic brkae, and traction control also replaced.*ml
Consumer stated while accelerating to match the speed of highway traffic, the accelerator stuck at approximately 40 to 45 mph, dealership examined vehicle, but could not reproduce the problem or locate any error codes. Consumer stateed the problem happened twice after the first incident. *yd
Request for compensation for engine failure as a result of a defective plastic intake manifold. *mr coolant leaked into the engine which was caused by the main bearing seizing.recall# 04v090000.the initial diagnosis was that the seal under the plastic plenum was defective.the check engine light had come on within two blocks of leaving the service dealer.they found that coolant leaked into the engine again and the warped plastic plenum would not seal against the manifold. *scthe consumer stated the vehicle needed other repairs such as a replacement motor for the passenger's window,power steering hose which was leaking, a rear wheel cylinder and a new transmission.
While drivingin a rain storm ona2 way highway at 50 mph windshield wipers suddenly quit working. This resulted in the driver not being able to see.consumer had to drive at 5 mph, and use the yellow medium line to guide him until he got to a turn off. Dealership indicated that the circuit board was bad, and needed to be replaced.
Read more
