We found the following complaints for HONDA S2000 (2000)
Read complaints for HONDA S2000 (2000)
Your web site does not search the vin.vin is correct.web site is unresponsive
Delayed airbag deployment (inflated after 2 seconds), upon hitting a tree.
While driving athigher than prescribedhighway speed another car cut in front.honda either swerved to miss the car, or the other vehicle left the road, andthen came back and hit the honda.hondawas airbourne and hit another vehicle traveling in the opposite direction.upon impact, neither airbag deployed.consumer was severely injured with contrition to the left lungs/ rupturedspleen, and broke top collar bone and two ribs.
There is a defect inelectrical system which is causingvehicle to fail to start/ windshield wiperfailure, and headlightsflashing on and off.these events occur onrandom basis or when consumer travels over a bump.please provide any additional information/attachments. Consumer states turn signals does not always work, also headlights do not just flash on/off they also sometimes just stay off, consumer states he requested that the security device that is installed in vehicle not be installed in his, consumer states one morning when the vehicle would not start he looked under the hood and saw two wires that had been crimped together, so consumer believes that the dealership inadvertenly installed the security device.
The honda s2000 is a manual shift car. The map sensor on this particular car adjusts when needed to control air intake of this car. During shifting at high speeds, the car would completely stall and shut off, due to some type of problem with this sensor. On dozens of occasions, i was in atlanta rush hour traffic and the car stalled. This was extremely dangerous, and i am lucky that i or nobody else was hurt. Luckily i am good with a stick shift and new to press the shift pedal and coast to a safe place where i could restart the car. When i took the car to the dealership, they explained to me that if they had a warranty on all parts of the car they would go out of business. Because of the approximately $900 repair fee, i sought help on the forums of the largest s2000 fansite. On the forums section of this site, there are literally dozens of people who have reported the same problem. In fact, there is a section on the forum called the "map wack", a procedure where you take a hammer and wack the map sensor to get it to work properly. I am outraged that they have recalled my back tail lights because the paint color fades, yet no such recall exists for a device that can stall an s2000 at any speed. I ended up getting a new throttle body and sensor and the problem has not resurfaced in 2 years. However, i am outraged that i had to pay for a manufacturer's defect. I only label this as a defect because there are literally dozens and even hundreds of similar complaints as mine on the s2000 fansite.
Honda f20c s2000 #4 cylinder failure , ahm did not cover this under my warranty.
Consumer states that while driving, the main bearings in engine failed causing engine to blow on 06-28-02.original engine had 35,600 miles on it.the dealer replaced engine and incident occured again on 9-8-02 with 27k miles on replacement engine.. Ts
Dip stick showed good oil level. However, upon driving it one day the engine blew and the low oil warning light did not come on.engine consumed oil enough that it threw a rod bearing. Replaced the bearings and it ran about 24 miles and it happened again. This time itdestroyed the crank in number 2 cylinder.honda corp. Wasn't very friendly about the problem but there seems to be a problem with oil distribution in this car.
Premature failure of connecting rods.
Vtec actuation solenoid suffered o-ring seal failure.*yd
Vtec actuation solenoid suffered o-ring seal failure.*yd
A/c compressor failed.*yd
A/c compressor failed.*yd
I am the original owner of a 2000 honda s2000...this past month i replaced the headlight assemblies for both headlights because the plastic shields which protect the lights had deteriorated so much that virtually no light was emitting from the headlights and the part which was the problem (the plastic lens cover or shield)cannot be replaced as a separate part..you must purchase the complete headlight assembly from honda...as there are no after market alternative parts...the cost for the headlight assemblies was $1,100 plus taxes...again nothing else other than the encasements were replaced..still using the original bulbs, motors, transformers, etc.....it's outrageous that a part would deteriorate to the point of it becoming a safety issue and that i am stuck with an out of pocket expense of close to $1,200 to correct the situation...thank you for any assistance you can offer in this matter.
I own a $32,000 honda s2000. After only 3 years, my tail lamps are so faded that they appear almost white. When i apply the brakes, it looks like i'm in reverse! this is a huge safety issue in my eyes and in the eyes of the cop that gave me a ticket for it. I went to the local honda dealer to get this fixed, and they will not fix it. I have an extended warranty, but they said that is not covered under the warranty. I told them it's a safety issue, they said they didn't care, word for word! "that is not our problem", is exactly what they said. This is surely my last honda! i'll spend my $32,000 or more somewhere else. Honda's loss.
Tail light lenses fading from red to pink within 3 years of ownership.police warning - stating modified lighting system.dealership will not replace.
The plastic rear window on the convertible top wrinkles and creases when the top is lowered.this causes a safety hazard in that car headlights are distorted during nighttime driving.the distortion causes the headligths to show an unknown number of vehicles in back of you.it could be only one, but appears to be many due to the distortion through the wrinkles in the plastic rear view window.i was almost hit because it appeared that one car was behind me, when in fact there were many-ans as i pulled out, i was almost sideswiped.there was no way to ascertain the number of cars behind me due to the distortion.during daylight, it is a distraction because everything is distorted.the customer service lady (joyce farr) from honda told me to put170 degree f water on the plastic window to get the wrinkles/creases out. (?!)i do not usually carry hot water around with me.another "fix" is to buy a "tube"and roll the window halfway down, then get out of the car, place the tube on the window, get back in the car, and finish lowering the top.reverse this procedure to put the top up.first of all, there's no place to carry a tube in this 2-seater sport car, and second, if you put the top up and forget to remove the tube (like when it's raining and you pull over on the side of the road to put the top up), the tube will get thrown in the road to create a traffic hazard.i believe that this is a saftey hazard, and am reporting it as such.
Side of red tail lights is pinkish white due to uv exposure after only 3 years. Tail lights are to be red in order to be recognizable as such, and not light pink.
Problems receiving reimbursement for taillight side markers.*mrthe consumer opted to order the parts from honda and replace the marker's himself due to the cost of labor.once the recall was received he returned the proper forms for reimbursement.he was later told that the manufacturer required proof from the dealer the the tail light was replaced because of the fading problem.
Both taillight are fading from a red color to a pale pink, almost white.i have kept this car very clean and under a uv protective cover at all times.the car is also driven only on weekends.
I have a 2000 model s2000 and the tail lightshave faded from red to white on the corners of the tail lights.this is a saftey hazard and needs to be corrected quickly and easily.i will contact a dealer to see if they can replace the taillights free of charge. I feel this should be a recalled item for anyone with the problem.i have owned two honda preludes and this is the first time this has ever happened and did not expect a problem like this on one of the best cars honda makes priced 10k more than my other hondas. *la
The honda s2000 is a manual shift car.the map sensor on this particular car adjusts when needed to control air intake of this car.during shifting at high speeds, the car would completely stall and shut off, due to some type of problem with this sensor.on dozens of occasions, i was in atlanta rush hour traffic and the car stalled.this was extremely dangerous, and i am lucky that i or nobody else was hurt. Luckily i am good with a stick shift and new to press the shift pedal and coast to a safe place where i could restart the car. When i took the car to the dealership, they explained to me that if they had a warranty on all parts of the car they would go out of business.because of the approximately $900 repair fee, i sought help on the forums of the largest s2000 fansite.on the forums section of this site, there are literally dozens of people who have reported the same problem.in fact, there is a section on the forum called the "map wack", a procedure where you take a hammer and wack the map sensor to get it to work properly.i am outraged that they have recalled my back tail lights because the paint color fades, yet no such recall exists for a device that can stall an s2000 at any speed.i ended up getting a new throttle body and sensor and the problem has not resurfaced in 2 years.however, i am outraged that i had to pay for a manufacturer's defect.i only label this as a defect because there are literally dozens and even hundreds of similar complaints as mine on the s2000 fansite.
Fuel cut-off during left turn when less than half a tank of fuel.creates unstable driving conditions, particularly when lateral g-forces are applied.research by ahm is needed to find remedy.
Transmission grinds at any speed when shifted to second gear, the limited slip differential leaks and is noisy.*yd
Differential failed, causing limited slip, leaks, and noise.*yd
Transmission grinds at any speed when shifted to second gear, the limited slip differential leaks and is noisy.*yd
Transmission grinds at any speed when shifted to second gear, the limited slip differential leaks and is noisy.*yd
Consumer stated that transmission jumped out of gear while driving at any speed. Consumer took vehicle to the dealer, and was told that the problem does could not be duplicated,and there was nothing they could do. Vehicle was still under warranty yet nothing was being done by the dealer to remedy the problem. Also, consumer contacted the manufacturer, who will not eventalk to consumer to get to the bottom of the problem.
Transmission grinds at any speed when shifted to second gear, the limited slip differential leaks and is noisy.*yd
The passenger seat belt made a noise while being retracted. It has been replaced 4 times.
In feb. Consumer recieved recall notice 00v-016 which states; when the convertible top is down and the seat is pushed all the way back the seat belt may not retract properly resulting in slack in the belts, the letter stated that a second notice would be sent when the inprovement part was available but consumer never recieved a second notice.nlm
Recall 00v016000. The parts are not available.
Nhtsa recall 00v016000 and manufacturer'srecall 00v016000/ seat belt retractor.no parts were available.dealer is having a hard time getting the parts from manufacturer.
When consumertakesfoot off the brake vehicle rolls backwards. Engine light flashes ondashboard. Dealership is aware ofproblem.
While driving my s2000 and turning on curvy roads the vehicle would not turn correctly and ended up in a field to the side of the road. We noticed the upper control arm spot weld broke free meaning the upper suspension mount was not connected and caused the incident.honda knows it's an issue with 2000-2003 model year vehicles and has issued a tsb sn040903 "09/01/2004 popping from front wheel upper control arm mount"multiple other people have had the issue over the years so much that many companies developed reinforcement plates such as these:https://originfabrication.com/products/upper-controll-arm-mounting-point-gusset-kit-honda-s2000if this issue had occured just 500 feet before i would have ended up steering into an oncoming semi-truck.
When driving at high speeds in the rain it felt like the vehicle was driving on ice.if there was any dip in the road, the vehicle hydroplaned. The consumer was unable to steer the vehicle, which was very dangerous, consumer had to drive very slowly. The dealer had been contacted, the dealer blamed the tires, the tire manufacturer blamed the car manufacturerp02enzas-02 only 11000 miles on the tires.
While driving my s2000 and turning on curvy roads the vehicle would not turn correctly and ended up in a field to the side of the road. We noticed the upper control arm spot weld broke free meaning the upper suspension mount was not connected and caused the incident.honda knows it's an issue with 2000-2003 model year vehicles and has issued a tsb sn040903 "09/01/2004 popping from front wheel upper control arm mount"multiple other people have had the issue over the years so much that many companies developed reinforcement plates such as these:https://originfabrication.com/products/upper-controll-arm-mounting-point-gusset-kit-honda-s2000if this issue had occured just 500 feet before i would have ended up steering into an oncoming semi-truck.
The plastic rear window on the convertible top wrinkles and creases when the top is lowered.this causes a safety hazard in that car headlights are distorted during nighttime driving.the distortion causes the headligths to show an unknown number of vehicles in back of you.it could be only one, but appears to be many due to the distortion through the wrinkles in the plastic rear view window.i was almost hit because it appeared that one car was behind me, when in fact there were many-ans as i pulled out, i was almost sideswiped.there was no way to ascertain the number of cars behind me due to the distortion.during daylight, it is a distraction because everything is distorted.the customer service lady (joyce farr) from honda told me to put170 degree f water on the plastic window to get the wrinkles/creases out. (?!)i do not usually carry hot water around with me.another "fix" is to buy a "tube"and roll the window halfway down, then get out of the car, place the tube on the window, get back in the car, and finish lowering the top.reverse this procedure to put the top up.first of all, there's no place to carry a tube in this 2-seater sport car, and second, if you put the top up and forget to remove the tube (like when it's raining and you pull over on the side of the road to put the top up), the tube will get thrown in the road to create a traffic hazard.i believe that this is a saftey hazard, and am reporting it as such.
Dealer tried to remove the convertible top due torecall 004v160000 instead of replacing the cover as the recall stated. Convertible top was glued together when the consumer went to pick it up. Dealer stated that the top is getting old.
The consumer is concerned about the long term service and safety issue of the rear plastic window installed within the convertible top.the concerns are,routine operation of the convertable top which puts scratches in the inside and outside of the rear plastic window along with creases and dimples which distort rear vision,(there are no provisions to prevent due to the design), when the convertible top is lowered and& stored, the rear plastic window wrinkles when it folds(which are impossible to completely remove)rearward vision becomes distorted, and contributes to a gross safety hazard, the plastic interior releases gaseous hydrocarbons and deposits a translucent film on the inside of rear plastic window which makes it cloudy and difficult to see through. *scc
The vehicle has a convertible top. Whentop returns back uprear windowbecomes wrinkled.consumercannot see out of window.
Convertible top rear plastic glass is distorted and causing severe visibility. Also, unable to get a glass replacment at consumer's own cost. Dealer / manufacturer notified, and neither are trying to help with this problem; seeking help from nhtsa in this matter.
While driving my s2000 and turning on curvy roads the vehicle would not turn correctly and ended up in a field to the side of the road. We noticed the upper control arm spot weld broke free meaning the upper suspension mount was not connected and caused the incident.honda knows it's an issue with 2000-2003 model year vehicles and has issued a tsb sn040903 "09/01/2004 popping from front wheel upper control arm mount"multiple other people have had the issue over the years so much that many companies developed reinforcement plates such as these:https://originfabrication.com/products/upper-controll-arm-mounting-point-gusset-kit-honda-s2000if this issue had occured just 500 feet before i would have ended up steering into an oncoming semi-truck.
While driving 80 mph, tread started shredding on right rear tire where it revealed cord on tire. Tire decreased amount of tread. Contacted dealer who indicated a possible cord problem. Original equipment for honda, ecsta, s2000,2000. Tire size 712 225/50r16 92v .. Consumer stated vehicle had an alignment, the tire pressure had been checked, prior to making trip, the entire tread wear groove was less prominent, dot number y018yaw2901.
When consumertakesfoot off the brake vehicle rolls backwards. Engine light flashes ondashboard. Dealership is aware ofproblem.
Rear plastic window has zero visibility due to scratching during convertable top use.this is during normal use of the convertable top.rear plastic window as already replaced once due to zero visibility and dealer will not replace or correct the problem currently.during reverse or lane merging, there is no outward visibility through the oem plastic rear window.
The vehicles rear window is made of plastic which made it impossible for the consumer to see out of the rear window.*nlm
The rear plastic window became opaque and yellow, to the point where 3 years after buying the car, you could not see through it at all.this made the car dangerous to drive when the convertible top was not down, because rear visibility was only through the side mirrors.while i would consider a functional rear window to be a major safety issue, honda refused to replace it, saying my warranty did not apply to "upholstery".i attempted to clean it with various window cleaners, and while they helped restore opacity, they did not restore transparency or visibility.
I own a 2000 honda s2000 convertible.since i purchased the vehicle, the rear window has steadily clouded to the point that i can no longer see through it.my local honda dealer (jones honda, 1335 manheim pike, lancaster, pa 17603717-394-0711)tells me the entire roof would need to be replaced in order to replace the window.the cost is in excess of $2,000.00.i know several other s2000 owners and the same thing is happening to their rear windows.
The vehicle has a convertible top. Whentop returns back uprear windowbecomes wrinkled.consumercannot see out of window.
Rear plastic window becomes wrinkled and is impossible to use as a window because it is too foggy to see you of.this makes for a very frightening and dangerous driving.
The vinyl rear window on my 2000 s2000 has faded i have had numerous run-ins with mylocal dealer and area rep you cannot see out of it, it has turned milky white making it a visual hazard since you can't see thru it also making that m.v. Will fail it for inspection, i have used all the recommeded cleaners as well as a boot they recommened. I had also filed a complaint withhonda automobile and got a nice dear john letter with no satisfaction case # no2003-11-1900869, after some inquiring byou can buy a new top with a glass back window from honda and have it installed for a mere $1600.00 but they will not correct a visual hazard condition, is this what honda has come to. Unhappily waiting for an answer.
Rear glass has a permanent glare when he turnsconvertible top, andmisoperation of window causes double vision.
Read more
