We found the following complaints for FORD EXPLORER (1995)
Read complaints for FORD EXPLORER (1995)
Air bag sensor light continued to stay on.dealer notified, and infomed consumer thatproblem was due to a clock spring failure. Any repairs would be at consumer's cost. Feel free to provide any further details on this matter.
Had a frontal collision, drivers air bag did not deploy.tt
As a past and present owner of ford vehicles, i wish to express my sincere dissatisfaction with the recent lack of support the ford motor company and its dealerships provide to insure the integrity of ford vehicle safety systems.i am writing with respect to a recent repair that was performed on the airbag system of my 1995 ford explorer.when the odometer read approximately 56,000 miles, the dashboard airbag indicator lamp began to illuminate.after taking it to dick ruhl ford at 7250 sawmill road in columbus, ohio for repair, i was informed that the cost of the repair ($425.45) would not be covered due to excessive mileage.in addition, two separate visits to the dealership were required to complete the repair since the source of the problem was not properly diagnosed initially.
No summary for above vehicle.
While driving airbag warning light appeared on the dashboard intermittently.
No deployment of airbag during accident, causing injury.
I rearended someone after trying to stop and my seatbelt did not lock in, nor did the airbagsgo off.i ended up with bruised ribs andheart.
Consumerwas driving 12 miles and he went to downshift,heard explosive noise the airbag went off .
Air bag light remained on. Dealer notified, and made repairs at consumer's cost. Please feel free to provide any further details on this matter.
Was traveling 50 mph when another vehicle pulled out in front. This causedexplorer to "t" boned it. Once this happened,air bags on the explorerfailed to deploy. Vehicle's front was damage, but was repairable. No injuries.
Truck was involved in rear -end accident, another vehicle with frontal impact 45 mph, neither dual air bags deployed. .
Consumer was involved in an accident in which the airbags did not experience deployment and the seat belts did not lock, consumer states the vehicle has been fixed, however the seat belts still do not lock in place, consumer was injured in the accident.
Going about 40mph when driver lost control of vehicle & hit telephone pole. Driver's side air bag did not deploy upon impact but passenger side air bag did deploy. Air bag deployed after driver left vehicle. Vehicle was totaled.
Abs locked up when applied and when car hit a telephone pole the air bags did not deploy. Please give more details.
Since leasing the vehicle, have had persistent problems with the front end, which resulted in wearing out several sets of expensive tires.reported same to seller ( r. Brown & sons, inc. ) but no resolution.involved in a crash in august, 1998, front end impact causing $2500 in damages, buckled hood, shattered bumper brackets, etc. But neither air bag deployed.took vehicle to a different garage because front tires again seriously worn.mechanic discovered right front stabilizer missing -- and no indication that it had ever been present.it is my belief that the vehicle was in a front end collision prior to our leasing it, a fact the seller did not divulge at the time.the salesman involved was terminated from employment at brown's shortly after we leased the vehicle.thank you for your time and consideration.
While driving ran off road and damaged front end, air bags did not deploy and fuel cut off system failed.
Car was in accident on a dry day hit on the passenger side door car rollover two time the air bag didn't deploy was in seat belt car was totaled.tt
Had a frontal collision, passengers air bag did not deploy.tt
No deployment of driver's and passenger's air bags during an accident, resulting in injuries.
Had a frontal collision, drivers air bag did not deploy.tt
Failure of the brake system caused consumer to have an accident, passenger side air bag did not deploy.tt
Consumer was traveling 30 to 40 mph when was involved in a head-on collisionin whichneither drivers nor passenger's side air bags deployed,causing injuries to the driver's side occupant. Alsothere is over 4000 dollars of damage to the front end of the vehicle.please provide any further details.
Thought the guy in front of me was going to go through a yellow light, so i figured i would follow in suit.thenhe just suddenly stopped, with me hitting him directly in the rearend.my seatbelts did not deploy, as my head hit and broke the windshield, and obviously the airbag did not go off.suffering chest bruising and troublebreathing.
I put on the brakes when i realized i was going to rear-end the car in front of me and when the accident happened the airbags and safety belt restraints failed, leaving me hitting the steering wheel and my head hitting the windshield.
While driving vehicle at a low speed at 30 mph owner hit another vehicle that was pulling out of a parking space,both airbags deployed but driver sustauned injuries.
Frontal collision, impact 12:00, speed 30mph, loss control of vehicle, hitting a tree, driver side airbag did not deploy.
While driving consumer hit some ice and slid off road and ran over a small tree, vehicle began to spin.while spinning, consumer hit two more trees on the driver's side, air bags did not deploy at all. Consumer was injured slightly.
Consumer was involved in a serious accident in which both air bags did not deploy. Dealer was not notified at this time.
Failure of the brake system caused consumer to have an accident, driver side air bag did not deploy.tt
Consumer received a information brochure regarding airbags & on/off switches. However, consumer wants a airbag on/off switch installed, dealer says they know nothing about brochure, denied installation.
Car was in accident on a dry day hit on the passenger side door car rollover two time the air bag didn't deploy was in seat belt car was totaled.tt
Gracomodel number 8480hg, dom 2/17/01. I have a 21 month old boy and he can easily undo the harness clasp when in the seat. I think that the clasp is made of a too flexible material.manufacturer doesn't agree. Could you check into this?
I was driving my car when it began to down shift around 35mph. Eventually, after adding more gas, it kicked into gear. My vehicle is an automatic. Once it down shifts, the od light begins flashing on and off. It has now been doing this consistently. The drive is not a smooth drive and when i am going approximately 50-60mph or more, the car begins to shake.
Consumer states the third brake light on the rear does not work, he states when the service technician drove vehicle into bay to be serviced, the brake light flashed on for the first time in several months, which possibily meant there was a short in the light, also the head lights flicker badly, especially on rough pavement.
I have a 1995 ford explorer the windows work sometimes you mit drive a block than thay don'tand the 4/4 will the same thing . My son has 1995 explorer it will do the same thing is there a recall if not ther shough be thank you .
Electrical system problems.
I got in my car a battery less than 2 weeks old was almost dead nothing was plugged in or on i drove got on the freeway about 20 min on freeway car stops won't move makes rev noiseeventually starts long enough to stop again at bottom of freeway exit starts again get in into gas station i sit in gas station for about 12 hours add 5 quarts of transmission fluid eventually car will let me drive about two blocks but come to find out i was driving well on fire race to get my dog and i out car catches completely on fire fire man says it electric under hood no previous problems other than the battery and the od off light coming on and off i had the car about a month police report number1702207 oakland ca police department
After operating the heater a fire occurred under the hood.it burned the plastic case around the heater core area. I was able to put out the fire with a fire extinguisher.i contacted the local ford dealership and was told that no recalls had been issued on my vehicle (1995 ford explorer vin# [xxx]).the service tech at the dealership said that the heater core could not have caused the fire and that perhaps a mouse had built a nest inside and that could have been the cause.he did not mention any service bulletins regarding electrical problems in the dash,a/c/,heater area that i later found on the internet. He suggested i bring the car in for repair.needless to say i am not taking it to the dealership.i do have an appointment for monday (1/24/05) at a repair shop. I will know more about costs to repair and the extent of the damage then. I fear driving the car knowing it could catch fire again and am using a loaner car from a friend at work. Updated07/24/2012 information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6)
Electrical problems inlude doors unlocking spontaneously, windows rolling up and down without pressing buttons, gas light comes on when gas tank was just filled, oil light coming on when oil is full and check engine light comes on for no reason.
The contact owns a 1995 ford explorer. The contact stated that while driving at 60 mph, the accelerator pedal was depressed but the vehicle failed to accelerate. In addition, the vehicle stalled and the check engine warning light illuminated. The vehicle could be restarted. The failure recurred on several occasions. The vehicle was taken to an independent mechanic where it was diagnosed that the electrical system failed. The vehicle was not repaired. The manufacturer was made aware of the failure. The failure mileage was 190,000.
1995 ford explorer eddie bauer. Headlights went out, found out through research that it is the lamp outage module located in the console of the car. Almost started a fire, completely melted module and affected other areas of the electrical system, very dangerous and no recall that i can find. Part is dealer only and 90.00.
Intermittent starting problems and stalls while driving
The electrical module failed.
My vehicle 3rd brake light is out all of a sudden don't drive it often and sorely surprise that it would just be completely out.it is expensive to replace and should be operable to the life of the vehicle.as it stands won't pass inspection and should be a recall on it.thanks
95 ford explorer parked in carport with engine shut off for 5 min while carried groceries up stairs - i hadleft dog in crate til finished unloading but when i came down noticed electrical smell, got out looked around car but did not notice any burning,got dog out and returned in three minutes to find key no longer unlocked door and could not see through windows - when door was opened smoke bellowed out, interior was covered with black soot, a hole bigger than a basketball was burnt out of seat and back of driver's seat was parched - had i not had the windows completely up it most likely would have to continued to burn.
Vehicle was parked on a residential street and engine had been off for 30 minutes. Driver was sitting in vehicle making phone calls when he smelled smoke and saw flaming wire under driver's seat.driver escaped unharmed and was able to remove some contents but vehicle was fully engulfed in flame within a few minutes, destroying vehicle entirely, melting pavement, burning nearby grass and trees, and melting bumper and paint on a nearby parked vehicle. Fire department arrived to extinguish vehicle.
Smell of burningplastic filled cabin of vehicle and floor under drivers feet got hot.disconnected battery and sent to garage.
The contact owns a 1995 ford explorer.while driving approximately 35 mph, the vehicle made extremely loud noises and became difficult to maneuver.the dealer stated that the tie rod assembly, odometer, and stabilizer bar all failed.the current mileage was 138,000 and failure mileage was 136,500.updated 10/23/07
Battery leaked acid and caused damage to the engine compartment components.tt
Firestone 7515 garners ferry rd, cola sc 29209 did following repairs:05/22/00 alternator, 05/01/00 both rear calipers & drums, 02/15/00eet/eec sensors, including temp sending unit, egr valve, coolant temp sensor08/07/99 front driver side lower control arm, ball jt, alternatorand horn .i purchased new tires 09/15/00.i removed goodyear tires pulliam put on my truck 08/27/98.
As i drive the explorer on the highway or at any speeds for longer periods of time(200+ miles), engine checklight comes on, and the horsepower is affected.gas mileage decreases to about 8 mpg, and this lasts for as long as the vehicle is driven. I have had the transmission replaced, and i have changed the spark plugs, the spark plug wires, the mass air-flow sensor, the fuel filters and the alternator. The problem is still occurring though. I would like to get the problem fixed so as to feel safe in this vehicle.
Horn pads replaced due to failure.
Firestone 7515 garners ferry rd, cola sc 29209 did following repairs:05/22/00 alternator, 05/01/00 both rear calipers & drums, 02/15/00eet/eec sensors, including temp sending unit, egr valve, coolant temp sensor08/07/99 front driver side lower control arm, ball jt, alternatorand horn .i purchased new tires 09/15/00.i removed goodyear tires pulliam put on my truck 08/27/98.
Ignition module failed.
The vehicle stallsin traffic when driving at slow speeds or coming to a stop,it cuts off completely.
While driving highway speed, truck will shut down "dead". Two area ford dealers can't reconstruct or determine failure. Please describe details.
Vehicle may stall while driving and not restart.
On sereral occasions the engine has either stopped running or run verty rough, such that it can only be kept running by stepping on the accelerator.it usually occurs after stopping for a short period of time and then restarting.the dealers service departments have been unable to identify the cause.
While driving highway speed, truck will shut down "dead". Two area ford dealers can't reconstruct or determine failure. Please describe details.
When turcks in motion feels like its lossing power, overdrive light comes on.tt
While driving, gas pedal completely collapsed; factory weld came off; lost all vehicle power; managed to drift to side of road; speed 45 mph.tt
Vehicle stalls for no apparent reason - i think this was the tfi problem.
While drivng, the vehicle engine shuts down and has to be restarted again.please describe.
Dt*:the contact stated while driving at various speeds the vehicle stalled without warning.the vehicle was taken to the dealership multiple times.although, an undetermined number of parts were replaced the stalling continued.after conducting research on the internet the contact determined the problem is with the ignition module.upon inspection the dealer determined there is no problem with the ignition module.
The engine has been stalling for the past year for no reason.
Last year my car would shut down. Go from regular rpm to zero and die. This would lock my steering column. I observed that this happened when the outdoor temperature exceeded about 90 degrees f and the car was exposed to sun (more likely to shut down that if i was coming out of a covered garage where the temp was lower, until exposed to the higher outside temp read. The steering column would lock as the ignition shut off whether i was idling in a drive thru lane or existing a freeway ramp where i would expect to go from 55 to 35 to zero at the stop, i would go to zero and bypass 34-1 mph. Just complete system shut down and column lock. I took the care in and they said it was the fuel injectors and paid $500 for who knows what because the problem persisted. It's hot. The problem persists. It's dangerous. Am i placing my family at risk? i already had the aerostar catch fire in the steering column while i was at full freeway speed . I am afraid that a similar defect is at work here. The aero was a manual so i could always rev to keep the rpm up, the explore is auto trans and goes from drive to lock. Please help me.
My car stalls continuously on a steady basis - may be going ok and then just stalls and may take up to 30 times to get it to start again - will only go ifit is in neutral and i slam the gas pedal - also anti lock brakes skid all the time and i am told there is no problem.
Everynow and then the 4x4 lights flash, while in 2 wheel drive, windows won't roll upor down. Goes away after a few minutes. Ford replaced ignition, but it still does it. Dealer was a bad dealer and did not know what was causing problem but replaced ignition anyways.
Due to the defective computer system, forwhich there is a service bulletin, transmission malfunctioned, causing vehicle tostall while driving. May result inan accident.
Main computer (ecm) failed.
As i drive the explorer on the highway or at any speeds for longer periods of time(200+ miles), engine checklight comes on, and the horsepower is affected.gas mileage decreases to about 8 mpg, and this lasts for as long as the vehicle is driven. I have had the transmission replaced, and i have changed the spark plugs, the spark plug wires, the mass air-flow sensor, the fuel filters and the alternator. The problem is still occurring though. I would like to get the problem fixed so as to feel safe in this vehicle.
Computer controlling engine fails when outside temperature is warm-normal when cool.
Circuit board overheated, causing fire.
Ignition locks up, key won't turn. Key may also be removed when not in full off position, both on multiple occasions.
Electrical: drove vehicle from georgia to florida, pulled into driveway, noticedsmoke coming up around the windshield, turned the ignition off andwas getting out of vehicle when he noticed smoke coming from the floorboard.there was no warning lights or any type of warning to letknow that the vehicle was about to catch fire. Vehicle was totaled.
Wiring assembly main loom failed. *dh
Wiring harness shorted out, causing the windshield wipers/radio and power door locks to fail.
While applying jumper cables to the battery of another vehicle cable started smoking, and plastic melted from the wires.dealership was aware of the problem.
Rear left door lock - cannot be opened from inside vehicle; 2nd failure; fixed 1st time by dealer at approx 30000 miles;;; transmission failed; o/d blinking; 3 planetary gears busted up;;; bad ground - rt headlight, rt turn signal, and high fan not working properly
My 1995 explorer was sitting and at 12:30am, when it caught on fire and burned. The fire started under the hood, and the vehicle was a total loss. The incident occurred on the evening march 23. This was the same evening that ford recalled the expedition for this very same type of problem, a cold vehicle catches fire under the hood. This was what our explorer did as well. However when we called ford they said that the explorer was not on the recall.
O/d and indicator light not operative.4wd indicator lights blink or do not operate.dealer says short in wiring components in shift selector assembly is causing problems.replacing entire assembly.
On 3/10/00 notice a burning smell, got worse through the week, had the heater core checked was fine($375).on 3/18/00 wife was driving home and the smell was sssooooo bad, checkedsmoke was coming frombehind glove compartment, headlights blew out but all fuses are fine, also the smell was always worse with the heat on, now the smoke seems to have stopped, but the truck smells sooo bad, can not get it in to the mechanic until monday 3/20/00, i saw there was an fire earlier from under dash in complaints section and thought this should be reported!!
While drivingvehicle caught on fire due to a faulty wirning harness.vehicle was tataled. Dealer and manufacturer have been notified.
While driving, thevehicle caught on fire, which started underneath the dashboard. The dealer was notified.the consumer supplied a fire report. *scc
Electrical fire started in computer console, entire truck blew up.tt
Computer malfunction causes vehicle to shift into lower gear.
Wiring under dash shorted, causing fire. *dh
While driving at 30 mph vehicle caught onfire in the steering column.
Vehicle caught fire while driving. Fire started in dash area of vehicle. Fire appears to be electrical. Vehicle was totally lost.
While parked, wires began to spark in the dash board and smelled of smoke then caught on fire. More information please.
The contact owns a 1995 ford explorer. The contact stated that the vehicle failed to start. The vehicle was taken to an independent mechanic, who diagnosed that there was an electrical failure. The vehicle was not repaired. The manufacturer was not made aware of the failure. The failure mileage was 130,000. The vin was unavailable.
The vehicle doesn't shift since its missing the transmission wiring harness o/d sensor cant locate a replacement part the check engine light goes on all the time it uses a lot of antifreeze speed control don't work fuel pump keeps going out.
The temperature guage stopped working 12/98. The dealership was asked to look at it shortly thereafter. They said it was nothing to worry about...probably something in the wiring of the guage, and it may be expensive to find it. Several months later when the check engine light came on, the dealership replaced the thermostat. The temperature guage immediately began working. We could have encountered a number of serious problems (such as overheating in texas in the summer), but the dealership didn't catch it. Then, our lock actuator went out. Because it was a rear door, the dealership said the manufacturer's warranty didn't cover it. We paid $188.16 to fix it in addition to the extended warranty. If the dealer's warranty covers the front doors, it should cover the rear doors. This makes no sense and cost us a lot of money out of our pockets! we only have 65,000 miles on our car.
Significant loss of radiator coolant in the snow, while idling, after a 10 degree night.
The contact owns a 1995 ford explorer. The contact stated the vehicle was moved, and while he was in his house he heard a noise and within seconds thefront end of the vehicle was on fire. The vehicle was towed to a salvage yard for further investigation. The fire report was not available. The manufacturer was contacted and they advised that the vehicle was included nhtsa campaign id number: 09v399000 vehicle speed control. The failure and the current miles were 187,000.
I don't know that the temperature gauge has ever worked correctly in this car - i just guessed dates and mileage, but i have had the car since 1997 (32,000 miles) and it has never worked correctly.this is my second ford explorer with this problem.furthermore, i recently spoke with a friend who had the same problem in his 1997 ford explorer.i do not think this problem is being reported because it is not obvious when the temperature gauge fails.
Firestone 7515 garners ferry rd, cola sc 29209 did following repairs:05/22/00 alternator, 05/01/00 both rear calipers & drums, 02/15/00eet/eec sensors, including temp sending unit, egr valve, coolant temp sensor08/07/99 front driver side lower control arm, ball jt, alternatorand horn .i purchased new tires 09/15/00.i removed goodyear tires pulliam put on my truck 08/27/98.
Engine replaced due to cooling system failures and continuous overheating.*skd
Radiator leaks.
The transmission is currently being rebuilt.a defective part allowed transmission fluid to leak into the radiator, and radiator fluid to leak into the transmission.the radiator must be replaced, and the transmission rebuilt.i only have less than 72,000 miles on the vehicle.i did not purchase the extended warranty when i purchased the vehicle because at a cost of over $22,000, i did not think anything should go wrong with the vehicle.i would like ford to pay for my auto repairs, and a recall to go into effect so that others with this car do not have to go through the same experience.100,000 miles is not unreasonable to expect a car's major components to last.
R&r thermostat and gasket failed causing the temperature to remain on cold.nlm
Thermostat failed.nlm
Whenever turning corners the vehicle would die out or cut off. When vehicle is at dealer's & test driven, the problem cannot be duplicated. The problem can occur often. Vehicle has cut off & then later restarted.
Transmission mount bolts missing causing clunking noise when transmission is out into gear.nlm
Consumer's concern over the handling by ford motor companies of the cruise control deactivation switch recall.*mrone nov 11, 2003 the consumer took the vehicle to the dealer because the brake light illuminated, brake fluid was leaking and the cruise control no longer functioned.the dealer quoted the consumer $5000 to fix the vehicle.the consumer declined the repair, purchased the part himself and replaced it himself.the consumer recently heard about the recall and contacted the manufacturer to see if he could recover the money he spent to replace the faulty parts.the manufacturer indicated that the consumer's vehicle was not included in the recall.the consumer's vehicle also experienced stall during acceleration, excessive tire wear, pulling to the right and transmission failure.
There would be a knocking sound from the engine and this cause the vehicle to shake while driving. The speed could vary for the knocking but when vehicle is over 40mph, the vehicle would shake. Have taken to independent mechanic and indicated no recalls. Would not repair vehicle for free.ts
While drivingat 55mph a pop was heard, like a gun. Heard something hitting underneath vehicle. Was making a ding, ding noise. Was in moderate speed lane, steering, whenleft front corner nose dived. Was not handling right. Managed to drive to friend's parking lot & checked vehicle. Noticedconnector bolt had snapped, but not separated.2nd time while vehicle was jacked up after the 1st repair connectorsnapped again. Was in a plastic casing. Took to ford & both bolts were replaced. Have the originial parts.
#3 piston had a hole burnt through it.
Driving on the interstate consumer heard a pop and saw smoke in the rear, pulled vehicle over and fire engulfed from under hood, possible engine fire.*jg
Vehicle stalls intermittently, mostly in hot weather.
Engine stalls after driving in warm weather, consumer believes it might be a vapor lock problem.*et
While driving the vehicle stallsand dies,giving the owner no indication.the manufacturer has bee notified.
Engine stalls when letting off gas in traffic or ideling when outside temperatures are 90 degrees or above.the engine is not registering it being overheated nor is there a need for additional water in the radiator.all of these have been checked.
Intermittent stalling.
After starting, and usually within a few minutes after being run, the engine will stall, such as when i leave my house, drive two miles to the coffee shop,.it does not seem to stall after being run say , for a prolonged period of time.its the first 5-10 minutes.took to local dealer, he said it needed a tune up, and dida tune up.veh. Still has problem.will stall on warm, cool, or cold days.temp. Does not seem to be afactor.
Engine stalls during hot wx.engine stalled when trying to enter traffic.restarts if hood is lifted to allow air to circulate and cool components.nov 16, 2000 dealership replaced pcm, bra processor asy-eec, evr, control asy-egr vacuum regulator, sensor asy-egr pressure valve for ~$600.not fixed.
Vehicle stalls at traffic lights/ stop signs and in the middle of traffic.
O/d light indicator came on, pulled over and parked vehicle, it wouldn't go into park or reverse, turned off engine, tried to turn engine back on and couldn't engine light came on, had to leave key in ignition, this happened on sat. Will contact dealer on monday, april l2, l999
Engine stalls during hot wx.engine stalled when trying to enter traffic.restarts if hood is lifted to allow air to circulate and cool components.nov 16, 2000 dealership replaced pcm, bra processor asy-eec, evr, control asy-egr vacuum regulator, sensor asy-egr pressure valve for ~$600.not fixed.
Intermittent stalling.
Vehicle stalls at various speeds(12times so far). Two dealers do not know what the problem is.
Safety defect.engine stalled multiple times after starting in hot weather.stalled in moving traffic. Same problem previous summer.jul 31, 2001 dealership replaced valve assembly-idle air control, value asy-throttle air by-pass for $230.previously paid $590 for same symptom and not fixed.
Possible design flaw caused engine to fail, resulting in fire.
Vehicle stalled at 35 mph while slowing down. Dealer has not been contacted.
The vehicle engine failed whiled driving, the dealer stated that the engins pistons failed, the head gasket cracked and blue smoke was coming out of the tailpipe, the dealer replaced the engine with a rebuilt engine, the vehicle was picked up from the dealer and while driving from the dealer the engine failed again.nlm
While driving at 50mph on the highway engine shut completely down. Dealer has had vehicle for over 50 days and could find no solution.
Truck was parked in driveway and caught on fire. Please describe .
Engine idles rough, stalls.dealer not able to determine the cause.
While traveling at highway speeds, vehicle loses power, consumer states its like she takes her foot off the gas pedal and by the time she pulls over, the vehicle runs like normal, noone can determine the cause.
My concern is that everytime we take our explorer on a road trip we get a check engine light. It will come on atthe first 200 miles of the trip. I've pulled over everytime it has happened and checked all the services on it. I always found everything is where it should be. When we have departed from every stop to fill up. The light comes back on right at 2mi. I took the vehicle in to have the computer checked for codes. Everytime they say it's the intake
Vehicle fire.
Engine makes loud popping noise intermittently. *dh
Wheneverweather starts to get real hot enigne stalls.
The engine failed while driving, the piston was shot, an engine gasket was cracked and blue smoke was coming out of the tail pipe, engine belt cracked.nlm
While driving through water , water gets sucked into the air intake,through the filter and into the engine resulting in hydrostatic lock-up and total engine failure.
Engine stalls when letting off gas in traffic or ideling when outside temperatures are 90 degrees or above.the engine is not registering it being overheated nor is there a need for additional water in the radiator.all of these have been checked.
Engine failure. *sd
Driving on the interstate consumer heard a pop and saw smoke in the rear, pulled vehicle over and fire engulfed from under hood, possible engine fire.*jg
While driving about any speed on a hot dayvehicle could stall without a prior warning.
Safety defect.engine stalled multiple times after starting in hot weather.stalled in moving traffic. Same problem previous summer.jul 31, 2001 dealership replaced valve assembly-idle air control, value asy-throttle air by-pass for $230.previously paid $590 for same symptom and not fixed.
1995 ford explorer stalls without waring at any given time,whether at idle or during acceleration. Has been checked out by local ford dealership where no problems have been found.
Pep boy part failure.*mrwhile driving 70 mph, consumer loss complete power.the tension pulley had disintegrated.this was the same tension pulley which was installed by pep boys 7 months prior to failure.
I retained the old part for your inspection. I also have photos of the part i email you. When this non-servicable part broke, raw exhaust blew through the firewall and gassed us out of the vehicle. I believe there is a potential carbon monoxide hazard.
Firestone 7515 garners ferry rd, cola sc 29209 did following repairs:05/22/00 alternator, 05/01/00 both rear calipers & drums, 02/15/00eet/eec sensors, including temp sending unit, egr valve, coolant temp sensor08/07/99 front driver side lower control arm, ball jt, alternatorand horn .i purchased new tires 09/15/00.i removed goodyear tires pulliam put on my truck 08/27/98.
Muffler failed. *dh
Due to the design of the floor mat, the floormat is sticking under the gas pedal,causing the vehicle to accelerate.
Problem with heater/a.c. System. *dh
Lighter popped out, knob and coil separated from each other, heating element stuck inside lighter, causing an electrical short. Dealer notified/ repaired, but refused to give work order receipt.
Electronic display console failed several times.
Power antenna failed. *dh
Radio failed.
Since purchase of vehicle in 1998 following components had to be replaced: transmission/fuel pump/ all 4 tires blew and not on recall/ cruise control/radio quit, and no longer able to buckle drivers seat belt.*et
While lowering spare tire the winch failed to allow the cable to roll back up into the housing, the jack handle/winch crank also jammed in the mechanism, this was the first time the winch was used, clerk at dealer said the part was poorly designed.nlm
My vehicle 3rd brake light is out all of a sudden don't drive it often and sorely surprise that it would just be completely out.it is expensive to replace and should be operable to the life of the vehicle.as it stands won't pass inspection and should be a recall on it.thanks
Parking light bulb failure.
Driver's side low-beam headlight failed.the vehicle has a bulb sensing system, and issued a warning to check the headlamps.i replaced bulb, but it still did not work.a day later the passenger side low-beam headlight also failed, leaving the vehicle without any low-beam headlights.after looking for a fuse or wiring problem, i found through research that this is a rather common problem in this and similar vehicle models, and has been indirectly acknowledged by the manufacturer in a tsb, but no recall has been issued. To me this seems to be a serious safety concern, and should be addressed more proactively.
High-mount brake light found inoperable during nc safety inspection.estimate of replacement is over $350.00.this seems like a part that should have a longer lifetime given the cost of replacement.are there any manufacturer reimbursements available for replacement?
Brake light assembly failed. Yh
No summary listed for above vehicle.
I have 2 ford vehicles from mid 1990's. The headlights on each have long since become thoroughly opacified. My guess is that this opacity occurred within the first 2 to 4 years.according my mechanic (who is a "ford man"), "this is a very characteristic and longstanding flaw with the ford brand, you would think ford would have dealt with this safety issue long ago, but ford has not and continues not to deal with it." this safeti issue/problem not inexpensive to remedy.
Clear coat is pealing on hood and over back hatch, transmission problems and headlight problems the headlight will not work on dim i have taken it to the shop and they can not find anything wrong with it.the sensor keeps going out on the transmission.
Lenses on headlights have become discolored. Dealer said yes it was a safety issue. But since vehicle was out of warranty they would do nothing . Consumer went, and had police look at headlights,.they stated yes he would be pulled over and cited due to headlights not being bright enough. The consumer believes it is the dealer's responsibility to replace the head lights.
I have a 1995 ford explorer which the headlight sensor continuously goes bad which would not be an issue if the headlights would continue to work without it.when this sensor, which has gone bad twice since i have had the vehicle, fails i should not be made aware of this until the headlight goes bad and the sensor does not alert me.when the sensor goes bad i get an indication that the headlights are out and when replaced they are still out because the true problem is the sensor has gone bad.how a sensor goes bad when it still senses the lamp not functioning is beyond me.this is a design deficiency in my opinion and the manufacturer should be recalling this item due to the obvious safety issue.the sensors should be replaced by the manufacturer at no cost to the customer and replaced with a sensor that if it were to fail would not affect the operation of the headlights.
Headlamp assemblies were originally clear plastic but have aged not very well to the point where they are opaque (cloudy) and i feel the light output has diminished considerably below original lumen levels.i have noticed majority of ford products that are over 3-4 years of age have clouded plastic headlamps. Close examination reveals slight crazing of the plastic outer surface as well as general dullness of the plastic.
1995 ford explorer eddie bauer. Headlights went out, found out through research that it is the lamp outage module located in the console of the car. Almost started a fire, completely melted module and affected other areas of the electrical system, very dangerous and no recall that i can find. Part is dealer only and 90.00.
Vehicle had been parked and locked for 30 hours prior to fire.fire appears to have spontaneously ignited in the left side of the dash area of the headlight switch and dimmer control for the interior lights.
Rear center tail light assembly had complete failure; dealer says it will cost between $250 and $300 to replace.i presume it is a safety problem since i failed annual inspection due to the failure of this component.are there other reports of similar failures?i am upset that i have to pay so much for a component that should have lasted more than 3.5 years.
I have a 1995 ford explorer the windows work sometimes you mit drive a block than thay don'tand the 4/4 will the same thing . My son has 1995 explorer it will do the same thing is there a recall if not ther shough be thank you .
Multi-function switch failed
After driving through water engine died after water was sucked into engine pistions due to airintake being located on bottom of vehicle.
Since purchase of vehicle in 1998 following components had to be replaced: transmission/fuel pump/ all 4 tires blew and not on recall/ cruise control/radio quit, and no longer able to buckle drivers seat belt.*et
Fuel pump failed.
Part is back-ordered country wide. Must mean that there is quite a few defective fuel lines which could cause a fire on impact due to leaking gas.
As i drive the explorer on the highway or at any speeds for longer periods of time(200+ miles), engine checklight comes on, and the horsepower is affected.gas mileage decreases to about 8 mpg, and this lasts for as long as the vehicle is driven. I have had the transmission replaced, and i have changed the spark plugs, the spark plug wires, the mass air-flow sensor, the fuel filters and the alternator. The problem is still occurring though. I would like to get the problem fixed so as to feel safe in this vehicle.
While driving ran off road and damaged front end, air bags did not deploy and fuel cut off system failed.
Consumer noticed while filling vehicle with fuel, fuelleaking out from under the wheel wells puddles. Manufacture and dealer has been contacted. Vehicle was service by technician and notice gas neck filler. Please provide further information. Ts
Fluid which was later confirmed to be oil from overflow tank spilled out on brakes on passenger side.i had to drive 2 hours back to north carolina because the dealership in galax, va closed at noon on saturdays.if i was by myself it would be a different story but i had my child with me.town and country ford confirmed the situation and stated that ford had sent out a memo saying if the vehicle was in warrantee the could put the cover on to prevent this problem but due to my mileage i had to pay $375.oo not including parts to have this taking care of.my question is if they put this device on and knew this could happen why not warn the consumer instead of finding out this way and why should i have to pay for a potential safety hazard which was not of my making.i called the 800 number on several occasions; got a claims number and that was it. The second time they said call town and country ford which the regional rep still hasn't responded. Next, i sent them a e-mail stating the problem and still no response. On the tires, which i had to replace myself, except for the spare which is a firestone, since the warranty was not honored stating that since they were only theywere only the stateside receiving dealership they were not responsible.the tires blew out less than two weeks after picking up the vehicle.i am very displeased with ford.according to the distance of travel i have resorted to renting so i would not have to worry about getting into an accident with my child in the vehicle.this is unacceptable and needs to be addressed.i can replace a vehicle but not a life.however, i refuse to pay for something which was already there to begin with.thanking you in advance for your time and attention in this matter.
When driving consumer can smellgas in the vehicle. Took vehicle for service and the dealer noticed that there was split at the seam of the gas tank.if the consumer were tohit a bump or a hard object, the vehicle might blow up while driving.
When filling tank with gas, regardless of level, gas comes back out of tank; flows onto ground underneath wheel well.tt
The straps that hold the fuel tank in place are broken and corroded, causing the fuel tank to be connected only to the fuel lines.please give any further details.
Please provide information. Ts
Gas gauge/indicator failure.
Gas tank reading is inaccurate, dealer cannot fix it.tt
Intermittent starting problems and stalls while driving
The contact owns a 1995 ford explorer. The contact stated that he noticed that there was a fuel leak. The vehicle was taken to the dealer who diagnosed that the fuel tank needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure who did not offer any assistance since the vehicle was not included in any recalls. The failure mileage was 56,000.
Dome lights stay on. Consumer is worried it may cause an electrical fire.
Courtesy light bulb shorted and smoke came from the center of the dash which caught fire.
Dome light will not turn off, causing poor visibility to the driver while driving at night.vehicle was taken to the dealer who could not determine the cause of the problem because the light turned off before arriving at the dealership.after leaving the dealership the light turned back on and would not shut off.
The drive gear in the transfer case failed and was replaced, 27k miles later the problem reoccured, the consumer believes that an incorrect component was installed, therefore causing it to fail again, while this was being repaired the dealer tore the door molding and the dash lights became inoperative.*nlm
Speedometer light does not work on the 30 to 40 mph range.
1995 ford explorer rear hatchwhere it connects to the hinge the spot welds broke. Went to 3ford dealerthey say this is been a problem read hatch to heavy welds weak. They said to contact ford. Called ford said nothing they could do for me. Told then rear hatchis going to fall off. Made a complaint . To see if a recall of fix problem. They said my problem. My fix.. I told them your dealers said this has been a problem and ford will not fix it. I need ford to fix my rear hatch be fore it falls off. Need your helpthis is been going g on for a year. I give up!
On the 1995 ford explorer, there exists a problem whereas an individuals couldbe trapped in the vehicle during an emergency, due to the lock mechanisms high rate of failure (poor quality material) on the rear passenger doors.to date, the doors cannot be opened from the inside, due to the (apparent) lock linkage breaking on each door.
Locking mechanismboke off inside ofdoor, making itimpossible foroccupants to get out of vehiclein case of anemergencywith both doors.
Child proof locks on both rear passenger doors have broken, causing the doors to become inoperable for exiting the vehicle.consumer states the child locks were never used, consumer states that both rear locks failed within one week of each other.
Latches on both rear doors are broken.
The interior read door latches are not operable from the inside of the vehicle.the rear doors can only be opened from the outside of teh vehicle.there is a child safety mechanism which provides this function, but it is not engaged on either door.it appears that both of the interior door handle mechanisms are defective.i believe that this is a very serious safety issue as a passenger in the rear seats could become trapped with in the vehicle.i have never seen a door handle fail in all my years of driving and working on automobiles, much less two on one vehicle.thank you.
Each ofthe 4 door lock mechanisms (passenger & driver) have broken at one time after 100,000 miles, preventing the occupant of that seat from opening the car door from the inside. Doors could be open from the outside (by rolling the window down and opening it using the outside door handle). The driver's door lock is currently broken - if the driver is inside without keys (keys are necessary to turn on power so the door window can be rolled down), he must then climb over the center console to exit through the passenger door. As mentioned, the driver side door lock is currently non-openable from the inside, but all other doors have had the same defect. There is a neoprene door lock part that breaks after 100,000 miles or so (i would guess), which causes this problem.*nlm
Rear hatchback hinges are buckled, preventing the hatchback from closing. Water gets inside because of the 1 1/2 inch gapin the rear hatchback. Also,exhaust fumes are coming from the rear hatchback.
Hood flew open while driving 55 mph. Dealer andmanufacturer were notified. Feel free to provide any further information.
Hood latch failure at approx.40mph causing hood to release and completely cover windsheild... Totally blocking forward vision.resulted in damage to hood and lower winshield area.($1000.00 +)if this would have happened at highway speed the chance for serious injury would have been great!!!!!fortunately traffic was light at time of incident(approx 6pm on sunday evening) .
Vehicle experiencing problem with hood unlatching while traveling on the highway at 7o mph, almost causing a vehicle collision. Occured after the vehicle had undergone repairs, most likely latches were not fully engaged.dealer /manufacturer notified. *ml
Parking brake shoes were frozen to rotor and ripped the caliper and drum assembly loose when vehicle started moving in four wheel drive.the brake line was severed resulting in brake fluid loss and loss of braking function.
Parking brake has failed again-3hrs after orig replacement.
Emergency parking brake fails to stay engaged.*skd
Owner states that while driving vehicle it stalls due to power train. Owner also notes that vehicle has problems with changing lanes and power train does not provide enough power to change lanes. Owner had problem corrected.
Speedometer does not work properly, resulting in incorrect miles. Dealer has been contacted.
For the third time, my '95 ford explorer during normal operation has had the throttle stuck open and accelerate to the point where the truck will not slow down even while applying the brakes. Even when the car has been put into the neutral position the engine continues to rev. I have to throw the truck into park and turn the truck off before the engine will slow down. The first time this happened a few years ago- i had a new transmission put in. The second time this occurred my mechanic told me that there was build-up which caused the throttle to remain open. This is the third time in a year and a half and i am now petrified to drive my once beloved vehicle. I can't possibly imagine selling this car and having this happen to another human being. Luckily, the second time this happened a co-worker was in the truck and i have an eyewitness. Please help me!! i am just a normal hard-working peron that is trying to get this problem fixed and am becoming more frightened by the research i am finding on this subject of the "open throttle".thanks-dani menzel
Driving in light city traffic, "overdrive" indicator light began blinking on and off a few seconds after pulling away from a traffic light, engine raced and wouldn't upshift, then it just coasted to a stop, and wouldn't go anymore.we had to have vehicle flatbedded to a repair shop, and found transmission needed a complete rebuild, which cost about $3,800.
My vehicle will not go in reverse.
1st incident:dec.12th 1998.concern: speed jumps on highway and surges only when speed control is on.cause: speedometer assembly binding.correction: replace speedometer assembly.cost to me $309.252nd incident:jan.5th 1999.concern: same as 1st incident.speed jumps on highway and surges only when speed control on. Cause: 14401 loom, sensor & assembly shorted.correction: repair loom 14401 speed control diag. R&r sensor & assembly.cost to me: $308.87.3rd incident:traveling on highway with speed control set at 70mph.explorer speed slowly increases to 80 on its own.i look at the speedometer, realize this and tap the brake.the explorer is still going 80mph or higher.i press the off button to the speed control but it will not disengage.i cannot stop the suv.i do not panick but i'm scared as i put on the emergency lights,press with all my might on the brakes and within a few minutes, get the explorer off the road to the shoulder.i put the suv in park, jump out of the car, look both ways, cross the highway, wave my arms for help and watch as my suv is parked with the engine stuck and running at 80mph or more.some good samaritans stop and i explain what happened.one of them approaches the explorer with caution and turns the ignition off and brings me my keys.they look at my manual and unhook the speed control box under the hood.i drove home with the emergency lights on (about 8 miles) going about 50mph with no problems then parked it.if another car had been near me when the explorer went out of my control, i could have hit them and there would have been injuries or possible loss of life at 80mph. Thank you.
I was driving my car when it began to down shift around 35mph. Eventually, after adding more gas, it kicked into gear. My vehicle is an automatic. Once it down shifts, the od light begins flashing on and off. It has now been doing this consistently. The drive is not a smooth drive and when i am going approximately 50-60mph or more, the car begins to shake.
The consumer believes that the vehicle undisclosed transmission problem caused the clutch cylinder, slave cylinder, master cylinder and pressure plate to fail multiply times. The clutch and slave cylinder was replaced four times, the mastercylinder was replaced three times, and the pressure plate had gone flat twice due to leaking.the transmission was hard to shift into low gears while in motion intermittently mostly in first and second. *sc
Transmission jumps out of park.
Consumer's concern over the handling by ford motor companies of the cruise control deactivation switch recall.*mrone nov 11, 2003 the consumer took the vehicle to the dealer because the brake light illuminated, brake fluid was leaking and the cruise control no longer functioned.the dealer quoted the consumer $5000 to fix the vehicle.the consumer declined the repair, purchased the part himself and replaced it himself.the consumer recently heard about the recall and contacted the manufacturer to see if he could recover the money he spent to replace the faulty parts.the manufacturer indicated that the consumer's vehicle was not included in the recall.the consumer's vehicle also experienced stall during acceleration, excessive tire wear, pulling to the right and transmission failure.
As a past and present owner of ford vehicles, i wish to express my sincere dissatisfaction with the recent lack of support the ford motor company and its dealerships provide to insure the integrity of ford vehicle safety systems.i am writing with respect to a recent repair that was performed on the airbag system of my 1995 ford explorer.when the odometer read approximately 56,000 miles, the dashboard airbag indicator lamp began to illuminate.after taking it to dick ruhl ford at 7250 sawmill road in columbus, ohio for repair, i was informed that the cost of the repair ($425.45) would not be covered due to excessive mileage.in addition, two separate visits to the dealership were required to complete the repair since the source of the problem was not properly diagnosed initially.
The speedometer/odometer module failed causing the speed to fluctuate erratically and surge when the cruise control was used.nlm
As i drive the explorer on the highway or at any speeds for longer periods of time(200+ miles), engine checklight comes on, and the horsepower is affected.gas mileage decreases to about 8 mpg, and this lasts for as long as the vehicle is driven. I have had the transmission replaced, and i have changed the spark plugs, the spark plug wires, the mass air-flow sensor, the fuel filters and the alternator. The problem is still occurring though. I would like to get the problem fixed so as to feel safe in this vehicle.
Automatic transmission failed due to defective planetary gear.
Overdrive light will start to blink, and almost immediatelyvehicle will not shift properly, it will keep slipping out of gear, eventually resulting in failure of transmission. Transmission has been replaced twice with the same light duty design transmission, but defect keeps occurring. *ml
Transmission shifts whenever it wants:65mph with cruise on or any other time just driving around town.
Problems with o/d light flashing, transmission shifts hard.*mr
Had to totally rebuild the transmission, something that should have to be done on such a low mileage car.
One year ago i noticed the overdirve light began flashing on my 1995 ford explorer. I was told by a local mechanic that my transmission had to be rebuilt. We spent $1000 on the repairs. Now, one year later, the overdrive light is flashing again and i'm told that all that is required is to clear the code because explorers do this all the time. I'm hearing from several other owners of explorers that these vehicles have very frequent transmission problems which would indicate a manufacturer defect.
When driving the jeep feels like it lossing power the over drive light on .tt
Transmission failed.
1995 ford explorer transmission. O/d off light blinking. From the sources on the net it looks as though i will have to junk it. Ford knows this trans is no good. It just started tonight. My wife has heart disease and my have to carry to hospital at anytime now i learn i will have to have a new trans. We are both disabled and bought this for dependability. Now from all the sites i have checked it is a pieces of junk. On the highway it just revs and goes no were that is bad in traffic can cause wrecks. It is not right for fordto know this is junk and not recallthese transmission hopefully u can help all of us with these junk fords. If someone there would get on the net and check out o/d off blinking on ford explorer you will see what i am and others are talking about.
I have had 3 transmission failures on my 1995 ford explorer. I bought it new.the first failure occured just out of warranty.it was rebuilt.the next failure occurred just out of the warranty for the first rebuild.i had a new transmission put in.the third failure is just beginning with the od light flashing and a hard clunk when the auto transmission downshifts into first gear.
Transmission failed.
Transmissionslipped in and out of overdrive while driving. Would have no warning. This causedvehicle to jerk. Problem was not intermittent. Took vehicle to dealership & was informed by mechanic that transmission needed to be replaced.
Have had extensive transmission and transfer case problems with this vehicle. I have replaced the transmission three times.
Ford supposely replaced our transmission in jan. 1999 due to a defect they could not explain, i paid $550.00, the dealer supposely paid $550.00 and ford was warrantying the remainder.the check engine light came on the vehicle 18 dec, 2000 .i told them that the vehicle was not shifting out correctly.so not to damage the vehicle i had it towed to our ford service department.ford installed an ait sensor at a cost of $293.78.the vehicle was ready to pick up on the 19 dec, 2000.due to the weather we did not drive the vehicle for several days, then after about 15 miles the o/d off indicator started flashing.i again called ford.i was told that we could drive the vehicle to the dealership.i talked with fred sizemore, service manager several times about the status of the vehicle.he told me that ford was bringing in a special computer to see if they could find the problem.finally on dec. 29 fred told me that the transmission again was out and that he was talking with ford about the problem.on tuesday, 2 january fred called to tell me that ford would not stand behind the new transmission.the person that fred spoke with said "there comes a time when the consumer has to take responsibility for the vehicle". I spoke with lovia at ford costomer assistance this morning.she advised me that ford had a 1 year/12,000 mile warranty on parts and we had exceeded that.i told her that this was "supposely" a new transmission and that it should have the same warranty as a new transmission.all service on this vehicle has been done at the dealer and we had the records to show that we had paid for the servicing.we can show the amount of money we have spent on this vehicle in maintenance.ford knew when they supposely put in this new transmission that we would again have problems and will not stand behind defective equipment.
While driving 65 mphtransmission quit without prior warning.
They replaced transmission 9/98, 2/99 i'm told i need a new transmission, my vehicle repeatedly loses power when driving, i've also been told that the clicking noise in my engine is a ford defect , but ford tells me i'm not covered because i didn't purchase a warrenty. A 95 ford explorer w/48000miles should not be having these problems. I also have a 91 and 93 explorers, a 73 ford ranchero(with original engine & transmission) and 83 ford conversion van and have never had any problems. This situation has really discouraged me from ever buying another ford product.
While driving onhighway transmission quit working. Vehicle would not moveforward or reverse. Manufacturer has been contacted.
Service bulletin:vehicles produced prior to 6/20/95.premature failure; flashing of transmission overdrive off land.result:stalling. Consequence:needing replacement.
The vehicle has given us good service until may of this year, when a problem developed in the transfer case. An oil pickup tube had broken, the unit had to be disassembled and repaired at a cost of $1304.53. This failure occurred at 72,202 miles and seemed peculiar at the time, but we accepted it as unusual wear at tear. On october 21st we took the car into the shop as the overdrive off light was flashing. The service advisor (jason savidge) called later that day and informed us that the transmission would have to be replaced. This was atotal shock to me as an automobile driver for nearly 60 years. Having ownedmany vehicles (and driven many more) of various manufacturers both foreign and domestic, i have never experienced such failures. I do not abusemy vehicles and have them serviced regularly. As a one time apprentice auto mechanic, a graduate mechanical engineer with 40 years of professional experience i know that properly designed rotating machinery, maintained and not abused will last essentially indefinitely. Ihave retained most of my vehicles for 100,000miles and more without such failures. I noted on your web site a number failures similar to ours, some multiple transmission replacements. I also realize this may not be a safety issue. But what does it take to get the manufacturer to stand behind their product. I contacted the customer service at ford motor co. And received and i am sorry but nothing in our records indicate ford motor co. Should pay or help pay for the transmission replacement.dt
Vehicle takenin for routine transmission oil change; mechanic noticed broken pieces of transmission positraction friction plate. Informed owner bearings needed to be replaced. Took vehicle to transmission shop & informed transmission was missing washers & it was poorly machined, the friction plate.
Transmission noisy. *dh
O/d light starts flashing. Very commen on 94-96 ford explorer transmissions. Must replace transmission. Should be recalled. Mine happed at 55,000. Had a new one installed by ford, happened again 20,000 miles later.
O/d light flashing/transmission failures. *nlm
A known transmission solenoid problem due to exhaust pipe temperature
Transmission gets stuck between first and second gear after driving for a distance.dealer has been contacted.
Driving from san diego to lax airport.1/3 of way there, o/d off light starts flashing, see in manual to contact dealership and to have vehicle checked.call rancho ford in temecula, ca, they said vehicle fine to drive, come in for appointment a few days later.vehicle not in correct gears, rpm awkward, too high, too low.then 1/2 back and hear pop sound, like gunfire, and see smoke coming from under vehicle.past experience with ford tells me not to trust them, so i pull over and call my mechanic.transmission blew cap off and cover undercarriage of car with trans fluid.mechanic said that as long as i did not rev above 2700, i would be okay.made it all the way home.had transmission rebuilt and reinstalled, two weeks later, same symptoms.this time new transmission.then 4 weeks later, problems occur again.take to aamco, and they say needs new torque converter, take to regualr mechanic, says needs new transfer case, take to rancho ford, they don't know what to do, and take to lake elsinore ford, where they run diagnostic, and find nothing is wrong.
Transmission light stays on while driving.the dealer has been notified.
Overdrive unit in transmission failed.
O/d off light flashing.dealer states transmission needs to be rebuilt.vehicle has had regular transmission maintenance, and has mostly highway mileage.vehicle not used for towing or plowing.failure seems unusual considering maintenance & use.family member also had transmission failure on 95 explorer at early stage (62,000).
Replaced 2nd transmission in october 1998, and 3rd infebruary 2001.consumer felt transmissionswere defective.
The dealer tried to sell me an extended warranty for $1500.00. I did not want it. Less than two months and 3000 miles, the transmission failed...the cost to repair it is $1400.00. To me, this seems oddly coincidental. I have tried to find any manufacturers defects with this transmission. I would appreciate any information concerning this matter.
Check engine light comes on intermittently since approximately 30,000 miles.no cause could be determined by several ford dealerships.at 109,000 miles o/d light began flashing.dealer diagnosed transmission failure and recommended replacement ($2558).5,000 miles later same symptoms appeared (o/d light flashing).dealer diagnosed transmission and pcm failure - replaced transmission under warranty and replaced pcm ($264).5,000 miles after that same symptoms presented themselves (o/d light flashing).dealer diagnosed transmission failure and pcm failure - both replaced under warranty.check engine light continues to present itself intermittently (typically on long drives).summary: 3 transmissions and 2 pcms failed within 12,000 miles.
Transmission slips, also overdrive light comes on and power drops.
Rear left door lock - cannot be opened from inside vehicle; 2nd failure; fixed 1st time by dealer at approx 30000 miles;;; transmission failed; o/d blinking; 3 planetary gears busted up;;; bad ground - rt headlight, rt turn signal, and high fan not working properly
Automatic transmission failed (parking pawl) while in parked gear resulting in collision with fence.
The overdrive light comes and will not go off . Please describe .
O/d light began to flash then the transmission went out, ford wants $2,000, so im going through an auto salvage for $845, will never buy ford again, they have a history of problems with there transmission. Of course the transmission went out 2 weeks after my warranty! i got a 1 year warranty for free from them because i had gone to carfax.com and found out that when i bought it from them there was an odometer roll back!
Vehicle exhibited hesitation while shifting, then, the pick up was slow. Six months ago consumer heard a clanking sound at slow speed. Currently, there was delay when shifting to drive and reverse. Also, intermittently vehicle wouldnot shift while driving. Mechanic statedtransmission needed to be replaced.
This is my 3rd transmission. My 1994 explorer had an ireprepairable transmission, so i had to upgrade at my cost to the 1995. In my 1995 i am now faced with replacing my 2nd transmission. So far i have been told the ford factory rep does not talk to the public. For each incident i have at least 2 weeks of "down time" while waiting to have the vehicle repaired. The transmission tech at town & country ford here in charlotte, nc indicates he sees this problem often with the explorers, yet no official recognition from ford. I feel powerless, and at the total mercy of ford. My bmw had 388,000 when i sold it and it never had transmission problems. My vehicle has been properly serviced, yet the ford warranty seems to speak for itself...inadequate. This is apparently due to an inferior, faulty product. Ford needs to do a better job backing up their products, and needs to do a significantly better job responding to a consumer with habitual major problems such as this transmission. How does ford expect to foster repeat business if the message they clearly send is the factory rep is not available to john q public. What the heck is their job description? i know the factory reps from the competing mfg'ers do field questions and issues from the public. I intend to leave ford if this is the best they can do and go to gmc, or a foreign mfg unless i can get some acknowledgement and relief!!!
Complete transmission failure. The o/d light started flashing along with large
Consumer states that transmission slips when trying to accelerate. Dealer notified.
No summary listed for above vehicle.
O/d off light flashing.dealer states transmission needs to be rebuilt.vehicle has had regular transmission maintenance, and has mostly highway mileage.vehicle not used for towing or plowing.failure seems unusual considering maintenance & use.family member also had transmission failure on 95 explorer at early stage (62,000).
On my sixth transmission on 1995 ford explorer have a life time warranty from tanner transmission but they will no longer stand behind there warranty because of the transmission being junk.
O/d off light flashed on and off for months. Ford would not admit a problem till it was out of warranty. Rpm's would go up dramatically for a few seconds while going down the road.abs sensor went bad causing unexpected and longer stopping distances at less than 20 mph. Thje abs brakes would kick inon dry pavement at slow speeds when turning and braking at the same time. Almost caused a couple crashes.
Called ford customer service for good will repair cost no help
Over drive light flashing, transmission is slipping and noisy between 1st and 2nd gear ,and also when it stops.
The contact owns a 1995 ford explorer. The contact stated while driving, she noticed that the vehicle would "shimmy and shake". Recently, she noticed that the vehicle would not shift into park so she had to use the parking brake to keep it stable. The vehicle had not been inspected or repaired at the time of the complaint. The contact called the dealership and the manufacturer who offered no assistance. The current mileage was approximately 184,000. The failure mileage was approximately 170,000.
The contact owns a 1995 ford explorer.whiledriving approximately 25-30 mph with the accelerator pedal depressed, the first and second gear slipped.this failure occurs on all road surfaces, including hills and leveled road and begins as soon as the vehicle is driven.the failure began six years after the vehicle was purchased.after the transmission was serviced at an authorized dealer, fluid began leaking.the contact took the vehicle back to the dealer for the third time and was informed that the transmission needed to be replaced.the vehicle is able to be driven, but the transmission has not yet been replaced. The failure mileage was 120,000 and current mileage was 131,000.updated 06/25/08
Due to the defective computer system, forwhich there is a service bulletin, transmission malfunctioned, causing vehicle tostall while driving. May result inan accident.
This is the second ford motor co replacement transmission to fail. The last one lasted 18,00 miles. Ford motor company informs me that there are over 500 backorders for this replacement transmission. If this is the case then there seems to be a serious problem with ford explorer transmissions. I've been given the run around for two weeks, told today 10/31/02 that it will be another month before i can get a transmission. This is a major problem and ford needs to be held accountable for producing inferior explorer automatic transmissions.thank you,dt
Noise in the transmission was said to be okay by the dealer despite the interior warning light.later, the owners wife experienced an extended downshift with the rpms reaching critical levels without any acceleration.vehicle was manuevered off the road wher it would not move.dealer towed vehicle and informed owner he would need a new transmission.
While driving on the highway at the speed limit transmission started to fall. Consumer could only get up to 35 mph. This could have caused a serious accident. Consumer was forced to get on the side of the shoulder. Then, vehicle would not go into drive or reverse,had to be towed. *ml
Od light started flashing at approx. 41,600 mi.was told by dealer listed above that fault codes indicated internal failure and best advice was to replace transmission-replace trans at 41,600 !!!!!!vehicle purchased from private party, great service records provied including transmission service at 41,158 by jackson ford mercury in jackson, ca.
It should be noted that freedom ford is the dealership that provided a $2,772.85 estimate to rebuild the transmission again.we purchased the vehicle from colorado springs jeep/eagle inc.the transmission has failed twice.the first time at 55706 miles, rebuilt at a cost of $2,628.92.now it has failed a second time with an additional 51644 miles on the odometer.this vehicle has been used mostly for highway driving, as i commute a 101 miles each day.it has not been used to tow and has only been used in 4-wheel drive during snow storms.the upkeep and maintenance on the vehicle has never been neglected and there is no reason that the transmission should have failed unless there is a manufacturer defect.i have contacted ford and was told there was nothing they could do to compensate me for the repair costs.i did brief research on the internet and found that this is a problem experienced by many ford explorer owners.there is information that indicates that ford is aware that the transmissions used in these vehicles have design defects, are poor quality and that they have a high failure rate. However, ford has done nothing to compensate their customers.i intend to pursue this situation and i would appreciate any information, assistance or investigative research your organization can provide.thank you for protecting us.
Transmission failed. From park to reverse or drive took 8-10 sec's for it's position. Dealer says nothing wrong. Trans. Specialists charged$2500.00 for rebuilt ford trans.
1995 ford explorer xlt rolled backwards after put in park. Customer states that the vehicle pinned her against the garage door. Customer states the vehicle rolled backwards on an incline and pinned her against the door.the consumer was injured. The muscle tissue and nerves to her right pelvis and upper thigh were severely damaged.
Transmission failed twice.
While driving 65 mph vehicle suddenly would not accelerate over 40 mph,overdrive light came on. Had vehicle towed to dealer who replaced transmission.
Automatic transmission overdrive servo seal failed.
I believe this truck was involved in a rollover accident before i purchased it. I think this because of the bad fiberglass work on the roof and bad paint job. I also believe this because of all of the front end problems i have encountered. I believe once this truck is involved in an accident there is no repair to make it safe again. I also wonder if the accident the truck was involved in is related to the tire and rollover recall from ford and firestone.
I own a 1995 ford explorer 4x4. I purchased it new and did not have any problems with thetransmission until last year when i had it flushed. I started to work the next morning and thetransmission began to slip coming out of first gear. I took it into aamco and they told me the transmission needed to be replaced. They also informed me the engine was strong, but the transmission would have to be replaced. I have no problem after it gets to second and third gear. It is really unsafe trying to merged into traffic, because of the hesitation trying to get out of first. If ford knows this is a major problem with this year vehicle, they should at least agree to recall these transmissions. I am sure most people have junked there trucks by name, but i am still hanging in strong 237,000 miles and counting, with the same slipping transmission. If anyone knows a solution to this issue, please let the rest of us know how to rectify our problems with the 1995 ford explorer transmission.
While driving at any speed vehicle will jump out of its original gear.this slows vehicle down. Consumer is afraid of being rear ended.please provide any further information.
No summary listed for above vehicle.
On tuesday january 16, 2001, the o/d off light started flashing while my wife was driving to work. I checked the owners manual for this status and it stated to have the vehicle serviced. I scheduled an appointment with columbiana ford for thursday january 18, 2001. I test drove the vehicle to see if anything felt wrong and all i could determine was the automatic shifting into overdrive was not working. On thursday january 18, 2001, i was shocked by the phone call from the ford dealer. They informed me that while the vehicle was in overdrive a part had broken. During this breakage, they stated that 3rd gear was damaged. The final shock occurred when they stated the repair estimate was $2313.00 for a new transmission. The final bill was for $2484.00. When i inquired about repairing or rebuilding the transmission they stated that it would cost the same as the new one. I called other transmission service companies and they verified the same conclusion as the ford dealer. This vehicle only has 67,000 miles on it and the transmission needed replaced.
O/d light flashing / transmission shifts hard into first gear when slowing down to a stop. Transmission always serviced according to owners manual.
Overdrive light starts flashing and vehicle shifts very hard. Dealer will not fix it because warranty has expired.
No summary listed for above vehicle.
Transmission failed. *dh
Consumer stated the overdrive off indicator light located on the instrument cluster flashed steadily, the vehicle then began braking roughly including a slight grinding sound during braking, consumer is requesting reimbursement for the replacement of the transmission, stating the manufacturer was aware of the transmission defects.
Transmission would slip in & out of overdrive while driving. Would jerk when this happened. Vehicle was controllable, speed was not a factor. Not an intermittent problem. Took vehicle to dealership & was informed that a new transmissionwas required.
Transmission has very hard downshifts which sound as if parts have been left behind.
Consumerhad a rebuilt transmission installed . But encountered the same problem as existed before. There was a humming noise,overdrive light stayed on .
Transmission problems since vehcile was purchased. This wassecond transmission, and itwas a rebuilt transmission. Contacted dealer.
The transmission went out at about 43,000 miles. Dealer is replacing transmission.
The contact owns a 1995 ford explorer.while driving the over-drive warning light will illuminate on the instrument control panel, and then the vehicle will hesitate before decelerating. He contacted the dealer, and a technician stated that this was a common failure for this model type. He then added that the transmission control module and the pcm have failed. The pcm needed to be replaced at an expense of $500.00. No repairs were made. The failure mileage was 55,000. The current mileage was 107,000.
Transmission caught on fire. Consumer stated that when the car is in drive it goes intoneutral and engine revs.
The transmission is currently being rebuilt.a defective part allowed transmission fluid to leak into the radiator, and radiator fluid to leak into the transmission.the radiator must be replaced, and the transmission rebuilt.i only have less than 72,000 miles on the vehicle.i did not purchase the extended warranty when i purchased the vehicle because at a cost of over $22,000, i did not think anything should go wrong with the vehicle.i would like ford to pay for my auto repairs, and a recall to go into effect so that others with this car do not have to go through the same experience.100,000 miles is not unreasonable to expect a car's major components to last.
Gear shift failure.
On 12/20/01, i tried to go into 4 wheel drive. Auto 4wd light didn't come on.driving it resulted in noise from underneath the vehicle: groans, loud clunks, severe vibrations, and difficulty steering the vehicle.next both 4wd lights started blinking. On 12/24/01, i took car to dealer.actuator was replaced, which they said was a problem in these cars. Charge was $441.77. I noticed same problem.back to shop on 12/26/01. After 2 days work problem was identified as water getting into the transfer case, contaminating clutches, causing them to stick and grab. Fix was to drain and refill the case. Cost $205.45.he said there was a vent but this would not have allowed for this problem to occur. Problem is less but still present.later, all the while still noticing the vibration, i noticed that both lights would begin to flash.the nhtsa site providedseveral tsb's that seem to deal with the problems: sb# 97314, dated 02/97; sb# bc0206970201, dated 01/97; sb# bc1011297020, dated 01/97.all deal with the transfer case binding or shuddering. Also two tsb's recommending the use of a revised vent tube to prevent water getting into the transfer case: sb# bc0133970201, dated 01/97; and sb# bc1012797020, dated 01/97.dealer was unaware of this procedure and did not suggest doing it on my vehicle.i still have problems with auto 4wd. The dealer has replaced a speed sensor, eliminating the flashing lights.bill is now $700 and not fixed the problem, known since 1997. Nobody bothered to tell me to have my transfer case fluid checked or the vent tube changed.dealer even told me that they normally would not check for this and that i should take it upon myself. Since this problem appears to be due to an inherent design flaw and has been known by ford since 1997, within my warranty period, i called ford customer service and asked for problem be fixed without cost to me. They knew of the problem and the repairs but refused to help since its out of warranty.
4 wheel drive failed, causing accident.
Transfer case malfunctioned ,causing the 4-wheel drive systemnot to activate cause unknown.please give any further details.
Torque converter failed, preventing transmission from shifting gears properly.
Torque converter failed.
The transmission and torque converter failed.nlm
I have a 1995 explorer that has had a major problem with the automatic transmission with only 42000 miles it was taken to the dealer and was told that it needed a rebuld.. But to my dismay to find out that it had premature wear on the torque converter and on the servo piston.. I know that this is an on going problem with ford explorer transmissions, i hope that something will be done about it cause as a consumer it is very frustrating knowing that many people have put in 3 or 4 transmissions before 100,000 miles.. Please help.. Thank you for your time
Overhauled transmission, replaced torque converter, seals, overdrive service, clutches
Torque converter failed.nlm
I have a 1995 ford explorer that has had many problems..currently i am having trouble with the coverter clutch. I have checked into this and it seems that many explorers are having this same trouble. I wrote a letter to ford motors companies and recieved a phone call from them telling me how sorry they were to hear of my complaints... I think this is pretty poor that they won't do something about this
The transmission and torque converter failed.nlm
The five lug bolts holding the rotor to the axle broke off detaching the whole right rear wheel from the vehicle.
The bolt that wholds the axle completey come off while driving. And ford said it is not a problem
The five lug bolts holding the rotor to the axle broke off detaching the whole right rear wheel from the vehicle.
The bolt that wholds the axle completey come off while driving. And ford said it is not a problem
Axle bearing assembly failure.
Differential axle seal failed causing fluid to leak.
Clutch hydraulic slave cylinder failed 3 times, but vehicle not driven off road or harshly. Most mileage has been high speed use over interstate highways from here to florida or northeast pennsylvania, without excessive shifting. First failure, 12/31/97, i was told slave cylinder failed when clutch pedal went to floor after a reported prolonged period of squealing. The squealing occurred as clutch pedal was being depressed. Dealer repaired it, sharing the cost, since it was only after 2/12 years old. Second failure, 03/04/98 after squealing noise again developed. Clutch assembly rebuilt. Subsequently, at each service visit, i reported the return of the squealing that preceded other hydraulic failure. 01/21/99 slave cyl. Failed again. I learned from the service manager that he had a nhtsa tech. Service bulletin, bc2301970501, in his possession since nov. Of 1997, preceeding the first clutch failure. This tsb advised replacing the slave cylinder lip seal with a newly designed one. The dealer did not do this the two times he replaced the slave cylinder, now it's failed again, and leaks. Who knows if it will fail again while driving, causing a loss of control? thank you for your time and assistance.
Drive train belt failure. *sd
Limited slip rear end clutch does not always engage.
Dealer was notified and they said it was a problem but had to do more research on the problem
Vibration felt through steering wheel/gas pedal, drive shaft to be replaced.
The transmission failed three times.nlm
Transmission failure. Owner was advised by transmission specialist that failure was unpreventable and is a common occurrence in ford explorers.
The transmission and torque converter failed.nlm
The transmission and torque converter failed.nlm
Transmission failure.
Clear coat is pealing on hood and over back hatch, transmission problems and headlight problems the headlight will not work on dim i have taken it to the shop and they can not find anything wrong with it.the sensor keeps going out on the transmission.
Vehicle sputters and shuts down when coming to a stop.
Computer system indicated a mechanical problem with the transmission, shift into a lower gear which significantly limited the speed of the car, replace some transmission parts, and reset computer, event occurred three times, replace transmission, to no avail.
When driving put car in fifth gear there is a noise dealer can't find problem.tt
I have a 1995 ford explorer the windows work sometimes you mit drive a block than thay don'tand the 4/4 will the same thing . My son has 1995 explorer it will do the same thing is there a recall if not ther shough be thank you .
When the vehicle is in 4-wheel drive lowit makes a popping noise,especiallywhen you the turn the steering wheel.
When vehicle was engaged in 4-wheel drive high at a low speed (28 mph) , hit black ice and threw vehicle across hwy. Vehicle rolled on one side, skidded and came up again. Vehicle has been repaired. The 4x4 wheeltransfer motor failed.
Have had extensive transmission and transfer case problems with this vehicle. I have replaced the transmission three times.
The drive gear in the transfer case failed and was replaced, 27k miles later the problem reoccured, the consumer believes that an incorrect component was installed, therefore causing it to fail again, while this was being repaired the dealer tore the door molding and the dash lights became inoperative.*nlm
While driving, on three different occasions at approx. 25-50mph, experienced transfer case failure, didn't transfer power to front wheels, engine runs , won't move, as though in neutral, renders vehicle totally inoperative, in contact with zone representative.
Seat belt just popped out took it to ford dealership to require about it and was told that it was broken and it would cost me 112.00 to have the seat belt replace. What if i was in a car accident and the seat belt didn't hold up to the requirements it would be to late to complain.
Driver's side seat belt latch is defective, (spring?)it is difficult to latchand repeatedly unlatches during drive times. I was ticketed for this problem.
The contact owns a 1995 ford explorer.while driving approximately 25 mph the front drivers side seat belt became unbuckled.the failure recurred intermittently while driving at any speed.he also mentioned that it sometimes takes repeated attempts to get the seat belt to initially buckle.the vehicle was not taken to be examined for the cause of failure, but an authorized dealer was notified and he was informed to replace the seat belt.the vehicle was not repaired.the failure mileage was 80,000 and the current mileage was 83,000.the vin was unavailable.
After seat belt buckle is locked in place and vehicle is in motion,seat belt while automatically unlock and retract without any help from driver.
Seat belts do not retract fully when disengaged. Catchin doors andcauses tears in belts.
Driver's side seatbelt buckle comes loose without prior notice.dealership is aware of problem.
1995 ford explorer - driver's side seat belt no longer latches. I fear the others will fail in the event of an accident. I am currently trying to find a replacement.
Consumer states that the driver's side seatbelt will not stay connected, it slides out.consumer does not feel safe driving this way.please provide any further information.*mr
While leaning back to buckle seat belt the back of the seat collasped. Dealer was contacted. The extra whole was punched out below the bolt whole.
Consumer states that the front seat belt buckles will not latch properly. Dealer notified. *mr
Seat belt on driver side/passenger side, and both on in rearwere shattered and were splitting.could not find what wascause of this problem.
Left driver side seat belt female recepticle does not secure lap and shoulder safety belt at all.clip in recepticle broke and will be properly secure safety belt restraint system for drivers side. Mr
Rear seat belts difficult to unbuckle due to the anchors being too close together with the release buttons facing. *dsh
Since purchase of vehicle in 1998 following components had to be replaced: transmission/fuel pump/ all 4 tires blew and not on recall/ cruise control/radio quit, and no longer able to buckle drivers seat belt.*et
The defective firestone atx tires failed causing the vehicle to rollover while driving, as a result the seat belts failed to properly restrain the driver causing injury to her back by breaking 8 vertebrae (attorney for client).nlm
Seatbelt releases when leaning forward and fails to secure driver in place
The four seat belts in the vehicle are broken and cannot be used properly, the consumer believes th manufacturer should pay for repair since its safety related .nlm
Consumer was involved in an accident in which the airbags did not experience deployment and the seat belts did not lock, consumer states the vehicle has been fixed, however the seat belts still do not lock in place, consumer was injured in the accident.
The driverside safety belt repeatedly disengaged/became unfastened for no appearant reason.we had it replaced at tom wood ford, after waiting at least 1 week!!!!my husband is an emergency room doctor; we never go anywhere without a safety belt!!!this defect is completely unacceptable and the replacement time was outrageous!!!
While driving front driver's seat belt latch just loosened without warning. Also, seat belt no longer works.
Seat belt will not stay latched. Seat belt button has lost its spring locking action.
Driver's seatbelt does not latch.the spring which presses the latch in place does not return to its intended position, keeping the seatbelt from being latched securely.normal use has led to this failure.fortunately, there have been no consequences yet.i plan on taking the vehicle into the dealer sometime soon, but unfortunately it may be a couple of days before i can get it serviced.
When trying to buckle the seat belt it takes three or four times to get the seat belt to work. Driving down the road the seat belt will come offwithout anything touching the seat belt.
Original front driver side seat belt buckle fails to latch.replaced with ford part no. F57z-7861203-c.
The original seat belts in the rear are extremely difficult to unbuckle. Grown adults take up to 1 minute to unbuckle. This is a such a potential hazard.
The spring in the seat belt release button does not work.there is no tension or resistance on the button.the button flops up and down in the buckle.the seat belt will not stay fastened in the buckle.the seat belt tongue does not catch and remain fastened in the buckle.
The driver side seat belt buckle failed to latch properly.movement by the driver caused the buckle to release.this was a sudden permanent failure of the seat belt lock. *scc
Numerous attempts to release the belt buckle from the locking housing mechanism failed and the fabric portion of the seatbelt had to be cut off, leaving the buckle in the locking mechanism.
Driver's seat belt will no longer stay in latched position.i suspect a spring or spring-like mechanism that holds the seat-belt releasebutton in the latched position has failed.
1995 ford explorer driver's seat belt buckle return spring appears to have suddenly broken, same as described in prior odi action no. Ea02011. Serious safety issue created: appears to latch, then unlatches suddenly while driving. Problem occurs frequently, so buckle/belt will be replaced asap.
Release button on the two rear seat belt buckles jam between the fold down seat back, and the occupieseat.
Driver's side seat belt will not release frombuckle. Seatbelt would get stuck, andwill not release at all.
Seat belts do not lock at all times.when hitting a bump they easily loosen.*ml
Driver's side seat-belt latch seems to have failed due to the spring mechanism.first, the belt would detach without warning (while driving) and then difficult to latch at all.seems to be similar to other complaints found on your web vrtc-dcd2038 (ea02-011)i called ford customer service (worthless - but they did confirm my car was manf. In april 1995 which seems to track with the batch of springs which have failed in other complaints.)my issue is that, even though the seat belt now is unlatchable, before it had spurious "unlatchings" while driving, leading one to suspect maybe i didn't latch it completely - so in an accident, not knowing this is a potential defect of this year of this component at time of manf., in an accident, the failure could have catastrophic effects of death and injury due to the failure of this primary safety restraint system.it seems a known potential issue with these specific date/components.why wouldn't ford at least inspect them and avoid this????
Driver's side seat belt intermittently would not latch.dealer was notified, and unwilling to assist because vehicle was not covered under a manufacturer's recall, and vehicle out of its warranty.
Called downey ford, and asked if there was a recall on seatbelt latch failure or warranty and was told no, so odered new seat belt and was billed 37.00.
Driver side seat belt buckle fails to engage clip. Appears to be a broken sping return in the buckle assembly. Ford customer care contacted and problem noted.
Driver's side seat buckles would not unlatch.two incidents on same day when i had to manipulate buckle tongue and bottom for approx. 5 mins. To get buckle to release.
Since purchase of vehicle in 1998 following components had to be replaced: transmission/fuel pump/ all 4 tires blew and not on recall/ cruise control/radio quit, and no longer able to buckle drivers seat belt.*et
Driver seat belt buckle will not latch.locking mechanism is broken which preventsbuckle from latching. Dealer /manufacturer notified, and informed consumerthat vehicle was not under a recall orwarranty.repairs would be at consumer's cost.the cause for the failure of the locking mechanism of the seat buckle is possibly faulty engineering and a poor design.
The driver's side seat belt latch will not stay engaged in the buckle. The latch continues to unlock and release from the buckle. Dealer has been notified of the problem.
The consumer was in an accident and the front seat belts unlocked from the buckle.
Front passenger seat belts will not stay locked in the belt buckle, and will release without warning. Dealership was notified, but did not resolve the problem.
This seat belt latch was made by trw and has failed to un latch on a number of occasions.my contact at fulton ford in canal fulton, oh 44614 said there was nothing they could do i would have to by a new part.i feel this is wrong this is a safety issue!it is against the law to drive without a seat belt.being this is a safety issue ford/trw should have to fix this problem!how many times should you have to crawl out of the seat belt because it want come un done.
The drivers side seatbelt latch failed while driving releasing the seatbelt, the seatbelt could be rebuckled but the latch continued to release intermittently and eventually failed altogether.nlm
Driver's side seat belt buckle will not latch.
The driver seat belt latch for the restraint has failed to stay secure.it latches and locks but then does release without warning and without interference from the operator while the vehicle is in motion.this is a potentially life threatening condition in the event of an accident.i have reported this to my local ford dealership and to ford customer service (monica) on june 7th.neither have offered to replace the defective latch without cost.i feel this is not a cosmetic defect but a potentially lethal problem with the equipment.the vehicle is a 1995 ford explorer limited edition.
Driver seat belt latch unlatches while driving. No consequences. Replacing asap.
Driver's side seat belt latch is defective. It is difficult to latch (like it has a broken spring inside) and it repeatedly unlatches during use.i have bought a replacement part, but have not installed it yet.
Driver seat and shoulder belt would not release from the locking mechanism,trapping the occupant in the vehicle,causing the driver to cut the seat belt.please give any further details.
Seat belt on the driver's side is defective. When the seat belts are latched together the seat belts will separate inadvertently. Consumer took the vehicle to the dealer, who statedthat the defect was in the buckle which will not hold the latch onceengaged.
Driver's seat belt fails to coompletly retract.*aw
In the rear seat, the two outboard seatbelts do not retract, which won't protect the occupant in event of a crash.please provide further information.
I put on the brakes when i realized i was going to rear-end the car in front of me and when the accident happened the airbags and safety belt restraints failed, leaving me hitting the steering wheel and my head hitting the windshield.
I rearended someone after trying to stop and my seatbelt did not lock in, nor did the airbagsgo off.i ended up with bruised ribs andheart.
Vehicle was at complete stop, impact 6:00 position, lap/shoulder did not retract.tt
Seat belt retractorsdo notwork properly. They do lock on sudden stopping situations. Contacted dealer, and dealer will inspectvehicle to check whats wrong. The dealer decided to replace the back seat belts to solve the proble.
Driver's side seatbelt will not go into retractor. Dealership is aware of problem.
Thought the guy in front of me was going to go through a yellow light, so i figured i would follow in suit.thenhe just suddenly stopped, with me hitting him directly in the rearend.my seatbelts did not deploy, as my head hit and broke the windshield, and obviously the airbag did not go off.suffering chest bruising and troublebreathing.
Seat belt will not release.
1995 ford explorer. Consumer states seat back failure in rear -end collision *tgwthe consumer stated while sitting at a red light, he was rear ended by another vehicle traveling at about 30 mph. Upon impact his vehicle was propelled into the vehicle in front of him.the consumer stated he was thrown backward,after the impact, the consumer realized he was out of his seat belt, lying across the second seat. The front seat was at a 45 degree angle and had broken brackets on both sides. The consumer sustained a serious back injury.
95 ford explorer parked in carport with engine shut off for 5 min while carried groceries up stairs - i hadleft dog in crate til finished unloading but when i came down noticed electrical smell, got out looked around car but did not notice any burning,got dog out and returned in three minutes to find key no longer unlocked door and could not see through windows - when door was opened smoke bellowed out, interior was covered with black soot, a hole bigger than a basketball was burnt out of seat and back of driver's seat was parched - had i not had the windows completely up it most likely would have to continued to burn.
On our 1995 ford explorer 4 door xlt, the main vertical support of the driver's seat back broke under normal stress (leaning back).a similar problem was addressed by ford recall #03504 (nhtsa 03v281000) for model years 1998-2002.ford is saying that there is no recall in effect for our model year and is providing no help.
At 5,000 miles a popping sound is coming from steering column.dealer was notified, andreplacedsteering column on two separate occasions.but,problem isstill reoccurring. Clip for upper bearing was out, dealer replaced and also retorqued bolts for lower shaft bearings, upper and lower steering shafts were replaced, lower was replaced twice , consumer states there is still problems with the steering.popping noise in right front seat.radio inoperable, dealer replaced, radio failed again, dealer replaced and repositioned wiring.console assembly replaced.
Some electrical component under the front drivers seat caught fire, consuming the seat portion of the assembly.
The rear seat frame locking mechanism fails to work. Need to use a tool to release locking mechanism to remove or fold seat down. Manufacturer gave okay to repair seat. Dealership refused to repair, even under warranty.
Vehicle was parked on a residential street and engine had been off for 30 minutes. Driver was sitting in vehicle making phone calls when he smelled smoke and saw flaming wire under driver's seat.driver escaped unharmed and was able to remove some contents but vehicle was fully engulfed in flame within a few minutes, destroying vehicle entirely, melting pavement, burning nearby grass and trees, and melting bumper and paint on a nearby parked vehicle. Fire department arrived to extinguish vehicle.
Driver's seat frame broke, causing driver to slide in the seat when making turns. *sd
Bolt on the driver's seat broke and the seat collapsed and went to the backseat of the car.dealercontacted and has not responded to the call.
Power seat switch failure.*aw
While drivingdriver's seat automatically reclined, laying the back of the seat completely down. There were no accidents. However, therewas recall 03v281000 on this issue.
The recliner on the drivers seat broke, which caused the seat to recline backwards, the dealer replaced the bolt.
The drivers side seat bolt on my vehicle broke, while i was driving across a school parking lot.this caused my seat to quickly fall back to the recliced position. I was able to maintain controll by pulling myself back to the upright position.this is a scary situation.thankfully i was not traveling at highway speeds and no one was hurt.
Failure of the driver's seat recliner mechanism in a crash.
While driving front driver's seat belt latch just loosened without warning. Also, seat belt no longer works.
While drivingdriver's side seatback collapsed. Dealer has seen vehicle.
Drivers seat collapsed while pulling over to side of the road.manufacturer was notified.consumer stated while pulling into a parking space, the driver seat suddenly snapped.he was propelled backwards into the rear seat, as the back of the seat broke.passengers were in the vehicle, and could have been hurt.also consumer was about three spaces from hitting another vehicle.consumer feels that the design should be corrected, and concludes that if he were going any faster, this incident would have caused an accident and possibly a fatality. (the chair is secured w/only one screw, which was a tor-x head screw: ford part#805885-558) *scc
1995 ford explorer. Consumer states seat back failure in rear -end collision *tgwthe consumer stated while sitting at a red light, he was rear ended by another vehicle traveling at about 30 mph. Upon impact his vehicle was propelled into the vehicle in front of him.the consumer stated he was thrown backward,after the impact, the consumer realized he was out of his seat belt, lying across the second seat. The front seat was at a 45 degree angle and had broken brackets on both sides. The consumer sustained a serious back injury.
Consumer just started to drive when driver's seatback fell back, latch assembly had to be replaced.
Driver's seat recliner bolt broke, causing the driver to lose control of vehicle and hit the side of a residence.
Anti-lock stop working each time the vehicle comes in contact with x-band radar signals from train signals or cellular telephone towers.anti-lock brake failure light comes on at the same place each day in my commute to work.
While traveling at approx 40mph i began to depress the brake pedal to slow down. At this time i had hit a pothole in the road. As i depressed the brake pedal it locked up and i could feel the anti locks attempting to active. I could not control the foward motion of the vehicle for approx 5 seconds almost hitting the vehicles in front of me. Thi
Service brakes, hydraulicdetails: i took my 95 explorer in for a recall (09s09) for a speed control deactivation switch which may pose a risk of fire if it leaked. When i got my veh. Back i looked under the hood to check their work. (i am a mechanic my self by occupation) they had replaced the pigtail to the switch but not the switch itself. The letter talked about the switch and not a pigtail leaking brake fluid. The switch is mounted on the master cly.above the exhaust manifold area. The recall intent was to have ford replace the pigtail and switch or the switch but only if the switch was leaking. The service manager would not give me any explanation. Is ford changing the wrong part. I am not sure how the pig tail will stop the brake fluid from leaking.
I am wirting because there are several recalls on my vehicle howerver i was told that the recalls are vin specific. Meaning that even though my vehicle is experianceing the same problems of cars that have been recalled of the same make model and model year the manufacture is not required to correct the defect. I have a problem witth that because it places the public at risk. In my case i have a 1995 ford explorer. The vehicle has been recalled for problems with the tie rods, sway bar links, and brakes. All issues that are saftey related. I have talked with other owners with the same car that have the excat issues. Obviously the problem is systemic and places the public at risk as this was one of the best selling models of that year. I am asking that you issue a recall all vehicles of this make and model for that year. This would alleviate the saftey risk casued by the defect. I believe that your office and the manufacture should take reasonable steps to adress the issue and act in the publics interest. Please contact me.
I took my 95 explorer in for a recall (09s09) for a speed control deactivation switch which may pose a risk of fire if it leaked. When i got my veh. Back i looked under the hood to check their work. (i am a mechanic my self by occupation) they had replaced the pigtail to the switch but not the switch itself.when i talked to the service manager about it he stated that the pigtail was the fire hazardand they only relocated the switch if it was leaking at the time of the recall. The letter talked about the switch and not a pigtail leaking brake fluid.the switch is mounted on the master cly.above the exhaust manifold area.was your recall intent to have ford replace the pigtail and switch or the pigtail and the switch but only if the switch was leaking. I will be waiting your reply thank you for your time.
I have a 1995 ford explorer and the dealer refuses to honor some of the recalls that have been ordered for my vehicle the recalls are listed belowrecall date:mar 15, 1995model affected:1995 ford explorersummary:the inner tie rod assemblies were improperly manufactured and can fracture causing shaking or shimmy at low speeds.dealers will inspect the inner tie rods and replace the suspect tie rods.potential units affected:49300recall date:mar 15, 1995model affected:1995 ford explorersummary:in some of the vehicles, brake tubes were misrouted between the master cylinder and the hydraulic control unit and results in exceeding the allowable stopping distances as required by fmvss no. 105, "hydraulic brake systems." in addition, seals within the master cylinder could be abraded by this condition over time resulting in an internal leak and a further reduction in brake performance.remedy:dealers will reroute the brake tubes.potential units affected:8100recall date:jan 31, 1996model affected:1995 ford explorersummary:vehicle description: multi-purpose passenger vehicles. This is not a safety recall in accordance with federal regulation 573. However, it is deemed a safety improvement campaign by the agency. The campaign will reinforce the bracket attachments of the rear liftgate gas assist cylinders which could pull away from the inside of the liftgate.remedy:ford dealers will reinforce the bracket attachments.potential units affected:1029380recall date:nov 28, 2000model affected:1995 ford explorersummary:vehicle description: sport utility vehicles. Under certain conditions, a front sway bar link can fracture.dealers will replace both the left and right front sway bar links.potential units affected:810,000.
Consumer states when road is wet brakes are inoperative. Dealer notified.
Whenever traveling at less (20) miles, when braking and hitting a bump,the wheels lock up. The systemhas abs.
Consumer was driving downhill on gravel road 10-20 mph, brakes were applied but failed to slow the vehicle, vehicle started to fish tail became unbalanced and rolled. *et
When driving at slow to moderate speeds, and attempting to brake normally, the abs system activates partway into the braking sequence.braking efficiency is drastically reduced, with braking distance significantly increased.thisresults in uncontrollable near collateral damage and personal injury.thesituationisespecially noticeable when navigating in parking lots where walking people and backing vehicles need to be avoided or when approaching vehicles stopped at traffic lights or breaking for crossing pedestrians.
Abs:when coming to stop with foot on brakes, but not pressing down completely or when hit bump, brakes engage prematurely, grab/hold vehicle/jerk.
Antilock brakes failed five times, once causing accident/rollover/injury.
While driving about 25 mph andstepping on brakes pedal brakes locked up, andvehicle moved side to side. Then, rolled over three times. Vehicle was towed to dealer,and totaled with no cause ofaccident found.
In icy weather when applying the brake, the abs brake failed.please describe .
Grease from the suspension fell on the left brake rotor,causing brake failure,could not stop vehicle.
Whilevehicle is being drivenabs brake system prematurely activates at low speeds also vibration occurs within the brake pedal. Please give any further details.
Anti-lock brake failure.
Front stablizer and sway bar have broken in the past 4 years, front tires can not be aligned and wear out faster because of this failure. Consumer states front stabalizer links were replaced due to on going complications, both front wheels bearing hub assembly failed, the front brake pads and rotors were replaced, and the front ball joints have some play.
Vehicle was taken in for check up. The brake rotors were cracked causing failure. Had them replaced.
When applying the abs brakes while going over a bump, the brakes failed to stop the vehicle.
Consumer was traveling 40mph &road sloped,brakes were applied &brake pedal went straight to the floor. Consumer had no control ofvehicle. Vehicle slid about 50 yards while going about 30mph.consumer couldn't prevent hitting another vehicle on the side.
Abs:brakes totally failed without warning while coming onto major st, pedal went to floor, driver shifted into park gear to stop vehicle, speed 5 mph.
While applying the brake pedal, it went to the floor.the driver was able to maintain control of the vehicle and drove it home. The cause has not been determined at this time.the driver will contact the dealer in the near future. Please provide further details.
Brakes: driving approximately 65mph , attempted to slow down the brake pedal would not depress.using both feet,put vehicle in neutral and coasted to a stop. Towed to dealer and they found nothing wrong. The next day driving on same highway the same thing occurred, and the vehicle caught fire.
Abs, brake failure when brakes were applied pedal was very hard, vehicle was impact 3:00 position swirled out of control and impacted again, speed 20 mph.
Brakes failed three times.
While driving vehicle on dirt road going down hill applied brakes hit bump brakes locked, loss of control then vehicle rolled on side. Vehicle is a total loss according to body shop.
The contact owns a 1995 ford explorer.while making a turn at 55 mph, the brakes locked without warning.as a result, the vehicle slid and crashed into a ditch before rolling over three times.the crash destroyed the vehicle.a police report was filed.as of november 6, 2007, the dealer had not inspected the vehicle.the driver sustained bruises to the back and shoulder blades along with cuts and scratches on his left arm.the contact felt that the antilock brakes caused the failure.the vin was unknown.the failure mileage was 120,000 and current mileage was 145,000.
Traveling down an incline vehicle exhibits total brake failure. No response from anti-lock brakes.
Ongoing problem with excessive wear of rotors and pads which are causing erratic noise when applying brakes. Vehicle been in/out of dealer shop on several occasions and problemstill occurring. Please provide any further details.
Started to apply the brakes to slow down when abs brakes locked up.vehicle spun around to the right & then back to the left. It flipped over & slid down the road. Vehicle hit guardrail. Driver had seat belt on at time of problem. Vehicle towed to dealership.
The brakes when they were applied after the recall work was done. Please describe.
Hydraulic cylinder failure causeddoors not to open properly.also, when applying brakes and coming to a stop,brake pedal would pulsate and go to the floor,resulting in extended stopping distance.contacted dealer.
The abs system was problematic.tsscc
Consumer contacted mechanic for grinding noises inabs braking system. But was informed thatfront abs brake pistons and caliperswere made of plastic. Please provide further details.
While driving at low speed, could feel abs system activating and brake pedalpulsating at braking. Dealer was contacted.*jg
Front/rear abs brake system on four different occasions and on dry pavement locked up, casuing increased stopping distance.
The abs system activates when braking down a steep slope and it activates when going over a bumpy road and braking at the same time. This incident occurred a number of times. Then the truck does not stop. Tt
Abs locked up when applied and when car hit a telephone pole the air bags did not deploy. Please give more details.
Whenever my wife complained about the brake pedal pulsating/vibrating, i told her thats normal because it's the abs.she said it didn't do it all the time and the few times i drove her explorer to find out what she was talking about it did not act up. I just recently bought me a vehicle she felt comfortable driving and i took her explorer for a week. The abs acted up during a normal stop and i completely went through a stop sign. I would like to add that we have only been notified of one recall on the explorer and that was many years ago.
No summary listed for above vehicle.
Abs, brake failure when brakes were applied pedal was very hard, vehicle was impact 3:00 position swirled out of control and impacted again, speed 20 mph.
When applying the abs brakes, the brakes failed.consumer stated master cylinder failed it was a defective part and dealership replaced at no charge, also front bumper and front strip is damaged.
Abs light came on intermittently due to road plastic in the system, later experienced total brake failure and no warning light.
While driving 35mph applied brakes and pedal went to the floor with no stopping power. Pumped brakes a couple of times, and brakes automatically started working properly. Dealer contacted.consumer stated the master cylinder failed.
Somtimes in wet or dry weather the abs anti-lock brakes lock up . Please describe .
Traveling down an incline vehicle exhibits total brake failure. No response from anti-lock brakes.
No summary listed for above vehicle.
While driving approx. 25-35mph, making left turn, suddenly rear wheels locked up, vehicle skidded across road, then rolled over twice.
O/d off light flashed on and off for months. Ford would not admit a problem till it was out of warranty. Rpm's would go up dramatically for a few seconds while going down the road.abs sensor went bad causing unexpected and longer stopping distances at less than 20 mph. Thje abs brakes would kick inon dry pavement at slow speeds when turning and braking at the same time. Almost caused a couple crashes.
While driving braking system malfunctioned, causingbrake pedal to travel to the floor and no braking ability,which may have resulted in a crash.happened twice,second time on may with 53,000.dealer cannot determine the problem.please provide further information and vin#.
Brake was very hard, unable to brake at all.
Consumer states that when trying to apply the brakes they can hear a loud noise and the brake pedal will go to the floor causing the vehicle to have extended stopping distance. Dealer notified.nlmtheabs sensor went bad causing the front disc brake to wear quickly.there was a recall issued regarding the front sway bar links.consuemr was charged for labor and parts.also the front lower ball joints were replaced as well as the outer tie rods.*jg
Recall repairs refused due to vehicle not being bought from local dealer.
When driving dirt road when applying the brake car skids .tt
Consumer states brakes failed once.* nlm
Failure of the brake system caused consumer to have an accident, driver and passenger side air bags did not deploy.tt
Rear brakes failed.
Ran through a red light and ended up in an accident because the brakes gave out. Please give more information.
Brake was very hard, unable to brake at all.
Front stablizer and sway bar have broken in the past 4 years, front tires can not be aligned and wear out faster because of this failure. Consumer states front stabalizer links were replaced due to on going complications, both front wheels bearing hub assembly failed, the front brake pads and rotors were replaced, and the front ball joints have some play.
While driving at low speed, could feel abs system activating and brake pedalpulsating at braking. Dealer was contacted.*jg
Brake pads and rotors are prematurely wearing out,cause unknown.please give any further details.
Firestone 7515 garners ferry rd, cola sc 29209 did following repairs:05/22/00 alternator, 05/01/00 both rear calipers & drums, 02/15/00eet/eec sensors, including temp sending unit, egr valve, coolant temp sensor08/07/99 front driver side lower control arm, ball jt, alternatorand horn .i purchased new tires 09/15/00.i removed goodyear tires pulliam put on my truck 08/27/98.
Consumer contacted mechanic for grinding noises inabs braking system. But was informed thatfront abs brake pistons and caliperswere made of plastic. Please provide further details.
Ongoing problem with excessive wear of rotors and pads which are causing erratic noise when applying brakes. Vehicle been in/out of dealer shop on several occasions and problemstill occurring. Please provide any further details.
When owner took truck for state inspection the front rotors and brake pads had to bereplaced because the surface on the rotorswere peeling off in chuncks. Owner did not experience any braking problems. Also, the underside of the explorer , the front link pin fell off,was missing.
With parking brake set, the rear disc pads froze to the rotor.upon starting vehicle in 4-wheel drive, the motion of the wheel ripped the brake caliper from its mounting (separating the pads from the rotor.) the brake hydraulic line was severed resulting in loss of break fluid and ultimately loss braking.emergency brake cable was broken providing no mechanical backup braking system.
Rear passenger's tire tread separated at 65-70mph, causingdriver to lose control.tire size p235 original equipment.prior to recall (00t-005) consumer replaced two firestone tires.the consumer wants to be reimbursed for the cost of two tires replaced before the firestone recall. Consumer also experienced noise when braking due to prmature wearing of brake pads and bad rotors which replaced.
Brake pads shifting causing noise.
Rear passenger's tire tread separated at 65-70mph, causingdriver to lose control.tire size p235 original equipment.prior to recall (00t-005) consumer replaced two firestone tires.the consumer wants to be reimbursed for the cost of two tires replaced before the firestone recall. Consumer also experienced noise when braking due to prmature wearing of brake pads and bad rotors which replaced.
Vehicle was taken in for check up. The brake rotors were cracked causing failure. Had them replaced.
On saturday, august 21, 2004 i pulled out of my driveway and attempted to apply my brakes.the brakes went to the floor with very little resistance.i continued driving about 100 ft and noticed the brake light had come on.i thought it might be the emergency brake.it wasn't.within 10 seconds of noticing the brake light i attemted to stop.after about a minute of applying the brakes, i stopped.i applied the emergency brake and decided to open the hood to see if the brake reservoir was empty.it was 3/4 low.i went back to the house and brought back a can of dot 3-4 brake fluid.i filled the reservoir to the proper level.i got back into the car and started the vehicle.i again pressed on the brake pedal and again the pedal went to the floor.i used the steering wheel to turn the tires to the far right and then to the far left.i looked behind both front wheels to see if there was any visible signs of brake fluid leaking.there was none.i decided to chock the back tires buy placing a large tree log behind each rear tire.i then crawled under the rear area of the vehicle and noticed dripping brake fluid coming from above the transaxle (rearend).i placed my hand above and felt the hydraulic line and felt a large amount of corrosion on the brake line.i am sending the vehicle to parkway auto repair on wednesday, august 25, 2004.if you would like to see pictures or the actual brake line after it is removed, please let me know.no crash or injuries occurred from this equipment failure.
The brake linerusted, causing the brake pedal to go to the floor when depressed. Consumer repaired the problem by himself.dealership was notified, but could not duplicate/resolve the problem.
Brake lines failed.
Dt:the contact stated there wasnhtsa recall 95v053000 concerning tie rod assembly, and recall 95v052000 concerningservice brakes; hoses, lines, piping and fittings. This vehicle experiencedthe sameproblems as indicated in the recalls, but wasnot included in the recalls due tovin. No repairs have been made at this time.
Replaced left brake hose.
Consumer statedcruise control malfunctioned. Consumer stated that brake fluid leaked onto the cruise control terminal. Consumer was concerned that the vehicle will catchon fire.the consumer attempted to buy a replacement part from the dealer, however, he was told the part was on back order.
Dt*: the contact stated while idling in the driveway for five minutes, the vehicle caught on fire.the fire department was contacted and extinguished the fire.the fire department determined the master cylinder switch on the front driver side started the fire.the dealer was not alerted.
Master cylinder failed, causing accident. *dsh
The consumer believes that the vehicle undisclosed transmission problem caused the clutch cylinder, slave cylinder, master cylinder and pressure plate to fail multiply times. The clutch and slave cylinder was replaced four times, the mastercylinder was replaced three times, and the pressure plate had gone flat twice due to leaking.the transmission was hard to shift into low gears while in motion intermittently mostly in first and second. *sc
When applying the abs brakes, the brakes failed.consumer stated master cylinder failed it was a defective part and dealership replaced at no charge, also front bumper and front strip is damaged.
We own a 1995 ford explorer xlt that has a faulty cruise control switch. Ford will not fix the switch, but has recalled other auto models to fix the same problem.
Master cylinder failure, missing a cotter pin from the master cylinder.tt
The master cylinder failed brake go to the floor .
While driving 35mph applied brakes and pedal went to the floor with no stopping power. Pumped brakes a couple of times, and brakes automatically started working properly. Dealer contacted.consumer stated the master cylinder failed.
Consumer contacted mechanic for grinding noises inabs braking system. But was informed thatfront abs brake pistons and caliperswere made of plastic. Please provide further details.
The master cylinder failed brake go to the floor .
Brake pedal has locked up twice, once causing accident. *dsh
Brake pedals sticks intermittently.
Brake light failed to illuminate due to brake booster pump incorrectly made too short not making contact. Please describe details.tt
Went over railroad tracks and suddenly the front end began to jump and skid on the front passenger side.whenthe cargot pulled over to the side of the road and we looked at it, the tire was completely turned sideways.we had it towed home.i checked under the front end in the morning and found a part of the tie rod completely broken.
At 5,000 miles a popping sound is coming from steering column.dealer was notified, andreplacedsteering column on two separate occasions.but,problem isstill reoccurring. Clip for upper bearing was out, dealer replaced and also retorqued bolts for lower shaft bearings, upper and lower steering shafts were replaced, lower was replaced twice , consumer states there is still problems with the steering.popping noise in right front seat.radio inoperable, dealer replaced, radio failed again, dealer replaced and repositioned wiring.console assembly replaced.
The steering column and all the parts associated with the steering of the vehicle were affected when the bolts that hold the clamps that secure the bushings to the steering column began to loosen. I examined the area carefully and noticed that because the bolts loosened,the clamps were given too much play. Within a short while, a month or two, the entire steering column and the shifter were completely secured by one broken clamp that held its place because of the bushings and a loose bolt. The other clamp was also broken but was laying on the floor board. It wasn't an expensive fix. I customized a metal clamp for each of the two places the went. They are the same clamps the electricians use to secure cables and wires to the walls and ceilings. I used the ones made from bronze. They are more pliable to shape for an almost perfect fit. With a little grease above and below the bushings and also some where the now bronze clamps hold the bushings, i believe that the steering column is as safe as can be. Also, the plastic that holds the cable that is used to adjust the shift indicator needs to be made of a different material. I'll get to that soon.
Steering problems.
The steering went out causing an accident.please describe.tt
The contact owns a 1995 ford explorer sport. The contact was driving approximately 60 to 65 mph when the steering wheel became extremely stiff and the vehicle suddenly spun out of control for sixty yards. The vehicle stopped spinning after it rolled onto its side. The police were called and a report was filed. The vehicle was towed to an independent mechanic where an insurance agent declared it as destroyed. The vehicle was never inspected by a dealer nor was the manufacturer contacted in regards to the failure. The failure and current mileage was 182,000.the vin was unavailable.
2 failures left and right side, link broke and fell off causing poor steering control.
I got in my car a battery less than 2 weeks old was almost dead nothing was plugged in or on i drove got on the freeway about 20 min on freeway car stops won't move makes rev noiseeventually starts long enough to stop again at bottom of freeway exit starts again get in into gas station i sit in gas station for about 12 hours add 5 quarts of transmission fluid eventually car will let me drive about two blocks but come to find out i was driving well on fire race to get my dog and i out car catches completely on fire fire man says it electric under hood no previous problems other than the battery and the od off light coming on and off i had the car about a month police report number1702207 oakland ca police department
Consumer was driving at 55 mph inleft lane,and there was a rattling noise. Consumerwas forcedinto guardrail. Had no steering. Took vehicle to dealer, and they said it wassway bar.
The contact owns a 1995 ford explorer. The contact stated while driving, she noticed that the vehicle would "shimmy and shake". Recently, she noticed that the vehicle would not shift into park so she had to use the parking brake to keep it stable. The vehicle had not been inspected or repaired at the time of the complaint. The contact called the dealership and the manufacturer who offered no assistance. The current mileage was approximately 184,000. The failure mileage was approximately 170,000.
While driving 15 mph the steering wheel seperated from the steering column, causing loss of control. Dealer states that mounting bolt is missing.please give further details.
While driving at a low speed vehicle shimmies andshakes.it is noticedmore at low speeds. Also, when it's windy outsideconsumer doesn't have a lot of control of the steering wheel.
Steering wheel would intermittently lock up during operation ofvehicle traveling at any speed. Steering wheel will lock up while traveling five mph, and turning into a driveway or while traveling on the interstate at high speeds.dealership has examinedvehicle, and determined that a "boot" around a joint in the steering column had deteriorated from exposure to sand.please provide any additional information / documentation.
Last year my car would shut down. Go from regular rpm to zero and die. This would lock my steering column. I observed that this happened when the outdoor temperature exceeded about 90 degrees f and the car was exposed to sun (more likely to shut down that if i was coming out of a covered garage where the temp was lower, until exposed to the higher outside temp read. The steering column would lock as the ignition shut off whether i was idling in a drive thru lane or existing a freeway ramp where i would expect to go from 55 to 35 to zero at the stop, i would go to zero and bypass 34-1 mph. Just complete system shut down and column lock. I took the care in and they said it was the fuel injectors and paid $500 for who knows what because the problem persisted. It's hot. The problem persists. It's dangerous. Am i placing my family at risk? i already had the aerostar catch fire in the steering column while i was at full freeway speed . I am afraid that a similar defect is at work here. The aero was a manual so i could always rev to keep the rpm up, the explore is auto trans and goes from drive to lock. Please help me.
Consumer lease car only had 600 miles the right rear shock came loose and make noise the steering shaft there is loose a lot of play.tt
While driving, pulling into a intersection, the steering locked and would not turn at all due to a broken steering coupler. The steering coupler was replaced on 9/24/97 by dealership.
Steering column failed. *sd
At 5,000 miles a popping sound is coming from steering column.dealer was notified, andreplacedsteering column on two separate occasions.but,problem isstill reoccurring. Clip for upper bearing was out, dealer replaced and also retorqued bolts for lower shaft bearings, upper and lower steering shafts were replaced, lower was replaced twice , consumer states there is still problems with the steering.popping noise in right front seat.radio inoperable, dealer replaced, radio failed again, dealer replaced and repositioned wiring.console assembly replaced.
1). Gas pedal sticks.2). Puffs of smoke come from steering column in the area of the emergency light button.3). Cruise control shuts off.
There is power steering fluid leak coming from rack and pinion on rightside. Dealer determined cause of leak, and replaced steering gear assembly.
Steering failure.
The vehicles power steering fluid leaked and caused loss of power steering. *nlm
Powersteering gasket failed.
While traveling in wet conditions at45mph consumer lost control, vehiclewent into a skid, resulting inminor injuries to occupants.vehicle was totaled. Please provide further informtation.
Power steering unit is leaking. Consumer must have complete steering rack union replaced instead of juststeeringunit which is more expensive.
The tie rod broke, causing loss of vehicle control.tt
While driving at 30mph into a curve and heard a clunk sound. Continued to drive vehicleto work and parked it.drove vehicle home from work couple of hours later and parked it. While driving at a higher speed,vehicle swayed from side to side at around 40-45mph. Slowed down to 30mph to keep vehicle under control. Took vehicle to mechanic, and they determined it to be a broke tie rod.
Tie rods failed.
Drag link failure.
While turning right or left at lowspeedsvehicle shook.consumer drove the vehicle to a body shop for inspection, andmechanic determined that the tie rods needed to be replaced.
Recall 95v053 mfg., 95s08 tie rod. Components replaced but problem is still failing. Miller ford in nj., still has truck and not fixed.
Front passenger's side tie rod sheared; off, causingloss of steering control, andresulting in a major accident.
Tie rods failed prior to recall.
The vehicle went out of control and crashed due to inner tie rod fracture. Yh
Dt:the contact stated there wasnhtsa recall 95v053000 concerning tie rod assembly, and recall 95v052000 concerningservice brakes; hoses, lines, piping and fittings. This vehicle experiencedthe sameproblems as indicated in the recalls, but wasnot included in the recalls due tovin. No repairs have been made at this time.
The contact owns a 1995 ford explorer.while driving approximately 35 mph, the vehicle made extremely loud noises and became difficult to maneuver.the dealer stated that the tie rod assembly, odometer, and stabilizer bar all failed.the current mileage was 138,000 and failure mileage was 136,500.updated 10/23/07
Tie rod separated from tie rod end.
Inner tie rods failed, causing vehicle to pull to one side after recall repairs (95v-013).
Tie rod recall repairs refused by dealer due to part unavailability.*skd
The lower ball jointsand the front outer tie rod end had to be replaced.mr.consumer stated the lower ball joints were loose and had to be replaced for a second time.
Having a problem getting parts from the dealer for tie rod recall.tt
While driving at about 35 miles on interstate suddenly could not control the car, it spinned around to the right backwards,went off the road and into a ditch backwards.
Tie rod end has no nut to hold rod in secure position.tt
Parts are unavailable to replace the inner tie rods on vehicle.tt
Fractured inner tie rod on driver's side caused loss of control of vehicle and crash into ditch.*mjs
Consumer states that when trying to apply the brakes they can hear a loud noise and the brake pedal will go to the floor causing the vehicle to have extended stopping distance. Dealer notified.nlmtheabs sensor went bad causing the front disc brake to wear quickly.there was a recall issued regarding the front sway bar links.consuemr was charged for labor and parts.also the front lower ball joints were replaced as well as the outer tie rods.*jg
While driving at highway speedsfront passenger's tire separated from the vehicle because inner tie rods broke, resulting in minor injuries.dealerhas been notified.
Dt*: the contact stated there was a clunking noise coming from the front end.the steering wheel shimmied at low speeds.there was a nhtsa recall, # 95v053000, regarding the steering: linkages: tie rod assembly.the dealership was not contacted.the vehicle was not included in the recall due to the vin.
Replaced inner tie rod.
Prior to recall vehicle suddenly spun backwards and crashed due to inner tie rod braking (95v-053). Yh
Rack and pinionstarted to leak oil at approximately 70000, causing a potential safety hazard.
Original replacement of rack and pinion assembly in june 1997 by dealer, repeat problem in november 1998, failure of replacement part.fluid leaking from front passenger-side assembly, with attendant deterioration in steering ability as fluid level falls.
Defective steering rack, causingfluid leaks.
There is power steering fluid leak coming from rack and pinion on rightside. Dealer determined cause of leak, and replaced steering gear assembly.
Consumer states that while traveling at 55 mph,on damppavement,consumer states another vehicle drifted into his lane,consumer tried to get to the left a little and vehicle made a sharp turn to the left. Consumer states vehicle was totalled.please provide any further information.
I have a 1995 ford explorer and the dealer refuses to honor some of the recalls that have been ordered for my vehicle the recalls are listed belowrecall date:mar 15, 1995model affected:1995 ford explorersummary:the inner tie rod assemblies were improperly manufactured and can fracture causing shaking or shimmy at low speeds.dealers will inspect the inner tie rods and replace the suspect tie rods.potential units affected:49300recall date:mar 15, 1995model affected:1995 ford explorersummary:in some of the vehicles, brake tubes were misrouted between the master cylinder and the hydraulic control unit and results in exceeding the allowable stopping distances as required by fmvss no. 105, "hydraulic brake systems." in addition, seals within the master cylinder could be abraded by this condition over time resulting in an internal leak and a further reduction in brake performance.remedy:dealers will reroute the brake tubes.potential units affected:8100recall date:jan 31, 1996model affected:1995 ford explorersummary:vehicle description: multi-purpose passenger vehicles. This is not a safety recall in accordance with federal regulation 573. However, it is deemed a safety improvement campaign by the agency. The campaign will reinforce the bracket attachments of the rear liftgate gas assist cylinders which could pull away from the inside of the liftgate.remedy:ford dealers will reinforce the bracket attachments.potential units affected:1029380recall date:nov 28, 2000model affected:1995 ford explorersummary:vehicle description: sport utility vehicles. Under certain conditions, a front sway bar link can fracture.dealers will replace both the left and right front sway bar links.potential units affected:810,000.
While driving the vehicle wanders to the side of the road (no shoulder), when steering back into the lane the vehicle began to fishtail and skid, the driver lostcontrol and the vehicle rolled over, no serious injuries only aches and bruises.nlm
At 5,000 miles a popping sound is coming from steering column.dealer was notified, andreplacedsteering column on two separate occasions.but,problem isstill reoccurring. Clip for upper bearing was out, dealer replaced and also retorqued bolts for lower shaft bearings, upper and lower steering shafts were replaced, lower was replaced twice , consumer states there is still problems with the steering.popping noise in right front seat.radio inoperable, dealer replaced, radio failed again, dealer replaced and repositioned wiring.console assembly replaced.
The sunroof cover falls off while driving.
Consumer was driving across bridge at approximately 50mph when smoke appeared from console. There was no emergency lane to pull over.consumer had to keep going until off the bridge. Vehicle caught on fire atconsole.key burned up inignition. Vehicle had power locks which caused consumer, and 5 year old child to have to climb outof window.consumer had to jerk several times onseat to get the child out. Fire department determined it was caused by electrical fire. The vehicle was totaled.the dealership was very concerned. But if no lives were taken ,it wasn't much thaat could be done.
When applying the abs brakes, the brakes failed.consumer stated master cylinder failed it was a defective part and dealership replaced at no charge, also front bumper and front strip is damaged.
Rearview mirror is located too low, causing a blind spot located in driver's direct line of sight, also bumper rusted.
Child's finger tip and nail was snapped off by roller pin located in the door.
Both interior rear door handles failed within 2 weeks of each other.failure of the door handle prevented egress from the the vehicle without someone opening the door from the outside.local ford parts department verified that there have been numerous failures of these parts but indicated there is no tsb or recall.
Vehicle's inside rear door handles have broken 5 times dueto a plastic internal part which is breaking. Cannot open the door when this occurs.
Blend door breaks -windshield frosts in cold wheater
Power door locks failed. *dh
The rear inside handles have broken.occupants in the rear can't exitfrom inside.the dealer has been notified.
On two different occasions both rear doors handles broke off from inside. Consumer was unable to open doors from inside. Dealer/manufacturer contacted and refused to repair uless cost goes to consumer.
The door handleon both rear sides is inoperative. Feels as though something is bent in the mechanism system of the inside door. Only way to open the doors are by outside. Dealer replaced new handleone year ago, defect is still reoccurring. This defect can result in an accident or injuries.
The front left door when shut has progressivley failed to close completely.
Driver side rear door handle, internal mechanism, broke and failed to open door.found that the passenger side rear door handle had already been replaced.
While driving electric door locks will disengage while driving, cause unknown. Please describe details.
Arm rest has broken.
The drive gear in the transfer case failed and was replaced, 27k miles later the problem reoccured, the consumer believes that an incorrect component was installed, therefore causing it to fail again, while this was being repaired the dealer tore the door molding and the dash lights became inoperative.*nlm
Failure on the rear passenger's and driver's side door handle, the door handle is broken from the inside of the vehicle.
Left rear door lock failed.*skd
Rear left door lock - cannot be opened from inside vehicle; 2nd failure; fixed 1st time by dealer at approx 30000 miles;;; transmission failed; o/d blinking; 3 planetary gears busted up;;; bad ground - rt headlight, rt turn signal, and high fan not working properly
No summary listed for above vehicle.
Upon closing the gate, bracket pulled away from the door and does not allow the lift gate to remain in the open position.
The weld on the right side of the liftgate broke, causing the it to fall which could have resulted in injuries.
1995 ford explorer rear hatchwhere it connects to the hinge the spot welds broke. Went to 3ford dealerthey say this is been a problem read hatch to heavy welds weak. They said to contact ford. Called ford said nothing they could do for me. Told then rear hatchis going to fall off. Made a complaint . To see if a recall of fix problem. They said my problem. My fix.. I told them your dealers said this has been a problem and ford will not fix it. I need ford to fix my rear hatch be fore it falls off. Need your helpthis is been going g on for a year. I give up!
Our 1995 ford explorer was parked on the side of our garage, well off a quiet street. When we came out in the morning to go to work we discovered that the back liftgate window exploded. Thankfully, this happened when it was parked. It would have potentially caused a major accident if we had been driving alone or with our children or friends. As we had talked with neighbors and called to get estimates weheard about this happening four times to other people. This was a definite safety issue and it should be recalled. As i filled out the questions below i am also so thankful that i did not have to type in a number other than 0 for number of deaths or injuries. Please notify us immediately if/when you decide that this was a serious danger to your buyers and will help correct and replace this default. Thank you.
Prior to recall the lift gate failed (99v-310). Yh
Hydraulic cylinders that hold the hatchback lid on the rear of the vehicle broke, causing the door to collapse on the owner. Dlr saidvehicle needed to go to a bodyshop.
Hydraulic cylinder failure causeddoors not to open properly.also, when applying brakes and coming to a stop,brake pedal would pulsate and go to the floor,resulting in extended stopping distance.contacted dealer.
The rear hatchback hydraulic cylinder has completely detached from the frame of the vehicle.please provide details.
Recall 99v310001/hydraulic left cylinders: vehicle was repaired concerning this recall. Currently,vehicle is experiencing the same problem except at the top of the weld. Dealer was not notified at this time.because of the recall bottom two brackets were fixed and two topswere not fixedtherefore,top right bracket weld broke off.
Hatchback support rod failure, when opened and proped in placesupport rods will fall out without warning pe95-032 active.tt
Rear liftgate support assembly separates from ligtgate when in open extended position, leaving only one strut intact, causing hatch to fall/injury. *sd
Weld on liftgate hydraulic cylinder failed causing liftgate to fall.
Liftgate gas assist bracket broke prior to recall/recall refused due to unavailability of parts. *sd
Lifttgate bracket broke.
When owner took truck for state inspection the front rotors and brake pads had to bereplaced because the surface on the rotorswere peeling off in chuncks. Owner did not experience any braking problems. Also, the underside of the explorer , the front link pin fell off,was missing.
Drainage channels design causing water to wash off the chrome.
Flipped 1995 limited explorer 5 times it is totaled
I have a 1995 ford explorer and the dealer refuses to honor some of the recalls that have been ordered for my vehicle the recalls are listed belowrecall date:mar 15, 1995model affected:1995 ford explorersummary:the inner tie rod assemblies were improperly manufactured and can fracture causing shaking or shimmy at low speeds.dealers will inspect the inner tie rods and replace the suspect tie rods.potential units affected:49300recall date:mar 15, 1995model affected:1995 ford explorersummary:in some of the vehicles, brake tubes were misrouted between the master cylinder and the hydraulic control unit and results in exceeding the allowable stopping distances as required by fmvss no. 105, "hydraulic brake systems." in addition, seals within the master cylinder could be abraded by this condition over time resulting in an internal leak and a further reduction in brake performance.remedy:dealers will reroute the brake tubes.potential units affected:8100recall date:jan 31, 1996model affected:1995 ford explorersummary:vehicle description: multi-purpose passenger vehicles. This is not a safety recall in accordance with federal regulation 573. However, it is deemed a safety improvement campaign by the agency. The campaign will reinforce the bracket attachments of the rear liftgate gas assist cylinders which could pull away from the inside of the liftgate.remedy:ford dealers will reinforce the bracket attachments.potential units affected:1029380recall date:nov 28, 2000model affected:1995 ford explorersummary:vehicle description: sport utility vehicles. Under certain conditions, a front sway bar link can fracture.dealers will replace both the left and right front sway bar links.potential units affected:810,000.
Consumer had recall 00v402 completed on vehicle and is requesting reimbursement.
Ongoing problem with vehicle vibrating while traveling at 45 mph on up. Firestone replaced tires, and the dealer replaced three of the wheels, and balanced the tires.however, problem isreoccurring.
Sway bar link failed prior to recall 00v402, dealer would not reimburse consumer for prior recall repair expenses, consumer is requesting reimbursement.
Actually had two very similar situations although one was on ice and the other due to hydroplaning. Was traveling on interstate in both instances at below speed limit and car seemed to float off to the right and then go into uncontrollable spins both instances were nearly identical with the last one resulting in car careening into ditch and striking guardrail i do not feel i was traveling at high rate of speed in either instance but am not frightened to ride in vehicle during any kind of inclement weather. Thanks daniel.( dot number: tire size: 15 )
Owner received recall notice (00v-402) in december, arrived at dealership for appointment on 1/24/01, told no parts available. Cj
The contact owns a 1995 ford explorer.the contact stated that the sway bar was fractured. The vehicle was taken to independent mechanic, who diagnosed that the link rod needed to be replaced.the failure recurred twice over a one year period. The vehicle was repaired.the manufacturer was notified of the problem. The approximate failure mileage was 60,000.
The vehicle began experiencing handling problems due to broken sway bars which failed prior to recall notice 00v-402 and caused the tires to wear, the consumer requests reimbursement.nlm
Suspension system failure, causing instability.
Prior to recall 00t-005 and 00v-402 the vehilce experienced sudden loss of control, the consumer believes the sway bar links malfunctioned causing the loss of control and that the tire also blewout during this accident, the consumer suffered a busted and swollen lip and body aches (firestone).nlm
While traveling sway bar links broke. Recall 00v402000/ manufacturer'srecall 00s47 for stabilizer bar didn't coverlower ball joint that broke.dealer wouldn't cover what was caused byrecall.
The front stabilizer bars failed prior to recall notice 00v-402 .nlm
Front stablizer and sway bar have broken in the past 4 years, front tires can not be aligned and wear out faster because of this failure. Consumer states front stabalizer links were replaced due to on going complications, both front wheels bearing hub assembly failed, the front brake pads and rotors were replaced, and the front ball joints have some play.
The consumer requested reimbursement for the two sway bars that were replaced prior to recall notice 00v-402.nlm
While driving at a low speed vehicle shimmies andshakes.it is noticedmore at low speeds. Also, when it's windy outsideconsumer doesn't have a lot of control of the steering wheel.
The steering column and all the parts associated with the steering of the vehicle were affected when the bolts that hold the clamps that secure the bushings to the steering column began to loosen. I examined the area carefully and noticed that because the bolts loosened,the clamps were given too much play. Within a short while, a month or two, the entire steering column and the shifter were completely secured by one broken clamp that held its place because of the bushings and a loose bolt. The other clamp was also broken but was laying on the floor board. It wasn't an expensive fix. I customized a metal clamp for each of the two places the went. They are the same clamps the electricians use to secure cables and wires to the walls and ceilings. I used the ones made from bronze. They are more pliable to shape for an almost perfect fit. With a little grease above and below the bushings and also some where the now bronze clamps hold the bushings, i believe that the steering column is as safe as can be. Also, the plastic that holds the cable that is used to adjust the shift indicator needs to be made of a different material. I'll get to that soon.
Front driver's side sway bar link fractured. The link had already been replaced as part of the nov. 28, 2000 nhtsa recall 00v402000, which was performed because, "under certain conditions, a front sway bar link can fracture."
Already having problems when purchased, car pulled right,rotate to back fixed pull.( dot number: tire size: p235/75r15 )
The sway bar link failed prior to recall notice 00v-402, the consumer request reimbursement.nlm
Ford motor company offered to reimburse the consumer forty five dollars for repairs done installing the front sway bar links.ford motor company would only do this if the consumer executed and delivered a general release for any and all claims that she may have had against them. * ph
Consumer was involved in an accident, when calling manufacturer,he was informed about recall 00v402 and was told that if the missing link had caused vehicle to crash company would replace, vehicle,however consumer received a letter stating that vehicle was too damaged for inspection.
Consumer's concern over the handling by ford motor companies of the cruise control deactivation switch recall.*mrone nov 11, 2003 the consumer took the vehicle to the dealer because the brake light illuminated, brake fluid was leaking and the cruise control no longer functioned.the dealer quoted the consumer $5000 to fix the vehicle.the consumer declined the repair, purchased the part himself and replaced it himself.the consumer recently heard about the recall and contacted the manufacturer to see if he could recover the money he spent to replace the faulty parts.the manufacturer indicated that the consumer's vehicle was not included in the recall.the consumer's vehicle also experienced stall during acceleration, excessive tire wear, pulling to the right and transmission failure.
Consumer received manufacturer'srecall 00s47 for sway bar link. Contacted dealer, mathiew ford in winchendon, ma tele#9782970001, dealer refused to do recall repairs becausevehicle had a salvage title. Consumerwas still driving vehicle. Dealer claimed hewas being told by ford manufacturer not to perform recall.consumer is requesting reimbursement for repairs.
Pe00 020; consumert was traveling about 75mph on highway and felt heavy vibration inside of vehicle . He went to pull over onto the shoulders.andvehicle took a 270 degree spinn out. Then, vehicle hit a road sign, and it flipped into a ditch.there were minor skratches.
Recall 00v402000/ stabilizer bar link stud;had made an appointment for 25 january,2001 on 2 january 2001, at 6 pm. Consumer was informed recall was not done due to no parts. Left vehicle until january 26, 2001, still no parts. Dealer then told consumer she could leave vehicle for a week in case parts came in. She then called ford company where she was told that she would just have to wait.
This failure causes a "serious" dutch roll (laterial roll) problem at cruise when a bump is encountered.
Vehicle pulls to the right. Also, rubber bushing is located close to the exhaust system without a heat shield, causing it to deform and fail.
The contact owns a 1995 ford explorer. The contact stated that his vehicle was previously serviced for recall 00v402000. While driving at approximately 30 mph, the contact heard a grinding noise from the front driver side wheel. The vehicle was taken to an independent repair shop where the contact was informed the stabilizing linkage pin was broken causing the bearings in the wheel to become defective. The vehicle had not been repaired at the time of the complaint. The failure and current mileages were approximately 127,000.
Steering problems.
During braking or going over a speed bump there is a poping or clanking sound coming from the front end of the vehicle. This happens intermittently.
No summary listed for above vehicle.
Front suspension failure, at slow speeds.tt
After replacement of tie rods, the steering wheel/front wheels not properly aligned and lug nuts not properly tightened.
Front driver's side sway bar link fractured. The link had already been replaced as part of the nov. 28, 2000 nhtsa recall 00v402000, which was performed because, "under certain conditions, a front sway bar link can fracture."
Initial failure due to very minor dip in i-80 from bridge to aspault transition.failure resulted in uncontrollable vehicle oscillation and subsequent spin-out including tire, bumper and minor injuries from spin.vehicle was unstable and would start oscillations above 30 mph.a second spin-out occurred when taking vehicle in for inspection at around 35 mph - no damage from accident.replacement of front stabilizer link resolved stability problems.( dot number: tire size: 16 )
Front end shakes and makes noises, difficult to control, and causes uneven wear to front tires due to misaligned front end. *dh
I believe this truck was involved in a rollover accident before i purchased it. I think this because of the bad fiberglass work on the roof and bad paint job. I also believe this because of all of the front end problems i have encountered. I believe once this truck is involved in an accident there is no repair to make it safe again. I also wonder if the accident the truck was involved in is related to the tire and rollover recall from ford and firestone.
Front suspension; the right front wheel and sterring wheel vibrate and shimmy at all speeds. The truck has never sat right it always seems to be leaning.
Consumer was traveling about 65mph on the highway and they heard a loud thumping noise, andvehicle started to vibrate.pulled vehicle over and changed the tire.
Front end failure.
A crinking sound would come fromwheel area while driving, dealer notified, and informed consumer that front ball joints needed replacement forlack of lubricationinrubber seal. Feel free to provide any further information.
Premature wearof ball joints, causingvehicle to make a loud clunking noise whenturning.dealer has been contacted.
Consumer was get gas at a gas station and the right front wheel came off the bolt on the ball joint came off.tt
Lower control arm broke, causing wheel assembly to fall off.
While traveling sway bar links broke. Recall 00v402000/ manufacturer'srecall 00s47 for stabilizer bar didn't coverlower ball joint that broke.dealer wouldn't cover what was caused byrecall.
Consumer states that when trying to apply the brakes they can hear a loud noise and the brake pedal will go to the floor causing the vehicle to have extended stopping distance. Dealer notified.nlmtheabs sensor went bad causing the front disc brake to wear quickly.there was a recall issued regarding the front sway bar links.consuemr was charged for labor and parts.also the front lower ball joints were replaced as well as the outer tie rods.*jg
Firestone 7515 garners ferry rd, cola sc 29209 did following repairs:05/22/00 alternator, 05/01/00 both rear calipers & drums, 02/15/00eet/eec sensors, including temp sending unit, egr valve, coolant temp sensor08/07/99 front driver side lower control arm, ball jt, alternatorand horn .i purchased new tires 09/15/00.i removed goodyear tires pulliam put on my truck 08/27/98.
The lower ball jointsand the front outer tie rod end had to be replaced.mr.consumer stated the lower ball joints were loose and had to be replaced for a second time.
Front suspension hitting the frame resulting vibration, due to leaking shocks, replace shock.tt
Front sway bar linksbroke, there was no prior warning, andvehicle could break down.
Lowered frontend torsion bars well below original allowable specifications, may cause the vehicle to tip over.
While driving could feel a strong movement side to side. Foundout that front sway bar was broken,and vehicle was taken to dealer and repaired.
On june 7, 2003the right side torsion bar broke collapsing the frame onto the right front tire.a metal inspector has inspected the part and indicated that it is a manufacturing defect.i went to my ford dealer, the parts manager at the dealership said too bad it happened now because my car is a 1995 and the warranty is up with no coverage for replacing this part.we will need to purchase both the right hand part as well as the left hand part #s f57a-bc rub & f57a-bc lub and have them installed.i can send pictures of the defective part.
The actual date and mileage is unknown. I just discovered the problem last week.both link pins that connect the front sway bar to the wheel assembly were missing.with the sway bar disconnected, the car sways severly in cornering or hard manuevers.i had the pins replaced at my expense.i contacted ford and they had issued a customer notification on 6 nov 2000 #00m11 that identified the (link pins breaking)problem for 1996-1997 ford explorers.however, the limit for mileage for ford to replace the parts was 100,000.i had at the time of discovery 102500 miles on the car.this problem, i believe, occured back in the summer because i started getting a lot sway on cornering.i figured that the shocks were bad do had them replaced in about september 2000.this didn't solve the sway problem.last week i was changing my oil and noticed that the sway bar was loose.after replacing the link pins my sway problem went away.i contacted ford customer relations, mellanie hall, and relayed my problem.i was told that ford would not pay for the repairs since my car was 2500 miles past their limit.i believe that this is a safety issue and may have been a contributing problem to the tire problem causing roll overs.this car, with out the sway bar attached, would definitely be unstable in hard turns and i am convinced that it could lead to a roll over.mellanie hall for ford, did not agree. I believe that this time of failure should be added to your investigation on tires and roll overs.i also believe that this should be safety recall and not be limited to a certain number of miles, consequently i should be reimbursed.
The sway brace has two broken studs, which allows the bar to rotate forward and then the two studs protrude from the front of the vehicle.this requires us to manually rotate the bar back to rest on the "attachment" points.
Suspension link from the control arm to the stabilizer bar fell off causing vibration and damage to other front components.
While driving on the expressway at about 65mph, the left hand stabilizer bar linkage broke. This threw the vehicle into the left lane. Took vehicle to dealer to check out problem.
Stabilizer bar attachment failed which caused excessive over steering.nlm
While driving on 93 south, a majormassachusetts highway, at 55 miles an hour on 11-1998, i swerved to avoid hitting a car that was going to come into my lane.my suv felt like it was going to tip over on its side.it felt like i was riding on two wheels.had i not been calm and steered correctly, the suv would have tipped over on its side.the second time, 8-2000 was on 95 south, in massachusetts.upon getting off the exit ramp, my suv again felt like it would tip over. I was going about 25 miles an hour.both times the sway bar links had to be replaced.i was charged for the first repair.i have replaced the five original tires which were part of the recent recall, with the same type of tire about a year ago.the cid sensor is a part that should last the life of the suv, according to the mechanic that worked on it.it had to be replaced on my suv.( dot number: tire size: p235/75/15 )
Pe 00 039/front suspension stabilizer bar link: vehicle experienced aslump while making a right turn out ofservice station. Dealer notified, and replaced both front stabilizer bar due to a rusted/broken bolt. Please feel free to provide any further details.
While driving the pins that hold the front stabilizer bar broke, causing poor maneuverability of the vehicle.please provide details.
Link that goes tostabilizer bar and lower control arm broke which may cause a loss of vehicle control. Links are now produced larger and bigger.please provide further information.
Pe 00 038/front suspension stabilizer bar (anti-sway bar) link failure: vehicle being reported with stabilzingproblem while driving 50 mph or more. Dealer was not notified at this time.
Front stabilizer bar link on left side missing.nlm
The contact owns a 1995 ford explorer.while driving approximately 35 mph, the vehicle made extremely loud noises and became difficult to maneuver.the dealer stated that the tie rod assembly, odometer, and stabilizer bar all failed.the current mileage was 138,000 and failure mileage was 136,500.updated 10/23/07
Suspension stabilizer links broke.
Stabilizer bar component broke and literally disintegrated/disappeared completely.nothing was left but the gaping hole where it used to be.shock failed either before or after component failure - not sure which occurred first.
The right stabilizer link broke on the vehicle, when ordering the replacement part, owner discovered that the part had been modified due to problems that were being experienced with this particular part (stabilizer link bolt). *mjs
Front suspension stablilizer bar link broke. Dealership was aware ofproblem,and mechanic has solved the problem.
Since leasing the vehicle, have had persistent problems with the front end, which resulted in wearing out several sets of expensive tires.reported same to seller ( r. Brown & sons, inc. ) but no resolution.involved in a crash in august, 1998, front end impact causing $2500 in damages, buckled hood, shattered bumper brackets, etc. But neither air bag deployed.took vehicle to a different garage because front tires again seriously worn.mechanic discovered right front stabilizer missing -- and no indication that it had ever been present.it is my belief that the vehicle was in a front end collision prior to our leasing it, a fact the seller did not divulge at the time.the salesman involved was terminated from employment at brown's shortly after we leased the vehicle.thank you for your time and consideration.
Linkage to the stabilizer bar broke while driving.
Both wheel bearing on the front have failed since ownership. Cannot find receipt at this time for specifics but i will find them or retrieve copies from the garage that performed the work.
Vehicle pulls to the right. Also, rubber bushing is located close to the exhaust system without a heat shield, causing it to deform and fail.
Vehicle was going 45mph and the passenger's side sway bar broke, causing vehicle to run offroad.consumer received a recall00v4402000/ manufacturer's recall 00s47 in reference tosame defect.months later.consumer was denied bydealer and manufacturer according to what the recall stated.
Sway bar loss caused uneven treadwear on two front tires - had to replace them (tiresize: 235 pf15)( dot number: tire size: 235 pf15 )
Low sped impact to left rear caused rollover. Ne-and one-half rotations, coming to rest on its roof. Passenger's side window shattered, causing partial ejection of 11-year -old passenger, crushing his skull and killing child. Two other passengers were injured.
While driving at any speed and with no warning rear suspension will lean to left, and will cause the consumer to have steering problems. Dealer notified.
Anti-sway bar detachedfrom suspension at low speed while pulling into a parking space.
While traveling sway bar links broke. Recall 00v402000/ manufacturer'srecall 00s47 for stabilizer bar didn't coverlower ball joint that broke.dealer wouldn't cover what was caused byrecall.
Whenever turning vehicle to right, the sway bar would make clunking noise. Vehicle would sway back & forth. Took to dealer and had it road tested. Put on rack & notice problems with sway bar & had it repaired. *ml
Consumer states that when trying to apply the brakes they can hear a loud noise and the brake pedal will go to the floor causing the vehicle to have extended stopping distance. Dealer notified.nlmtheabs sensor went bad causing the front disc brake to wear quickly.there was a recall issued regarding the front sway bar links.consuemr was charged for labor and parts.also the front lower ball joints were replaced as well as the outer tie rods.*jg
Consumernoticed that sway bar broke because he could hear a banging noise.
Left side sway bar broke causing steering problems.nlm
Consumer had the right front sway link replaced because it snapped, the left sway bar link was rusted to a point where it was close to breaking and was also replaced, consumer had repairs prior to recall 00s47, ford did not give consumerfull refund for repairs even though it says in the refund letter that full refunds would be given for those consumer's who replaced sway bar links prior to the date of the recall letter.
Sway bar broke on passenger side, also stabilizer broke, causing loss of steering.
Nhtsa recall 00v402000. Consumer has contacted dealer for remedy, but was unable to have work completed for lack of parts. Please provide further details.
While driving on interborough parkwayin queens, ny and going around a turn to the right, rear end fishtailed to the left. Felt as if vehicle lost control.
Consumer was driving at 55 mph inleft lane,and there was a rattling noise. Consumerwas forcedinto guardrail. Had no steering. Took vehicle to dealer, and they said it wassway bar.
Concerns about the sway bar problem, explorer has very stiff handling. *cj
Equipped with towing package and without ever having towed a trailer or heavy usage/weight in the rear, the rear springs are sagging, causing front lights to rise and irritate other drivers and excessive wear on tires.
While driving 60mphsway bar broke, causing consumer to lose control.dealer contacted.
Both the front left and front right sway bar links have failed on this vehicle. The links have simply fallen off of the vehicle. I saw an article in the newspaper that nhtsa was investigating this component on the 1995 explorer and wished to provide my information as well.
Both the front left and front right sway bar links have failed on this vehicle. The links have simply fallen off of the vehicle. I saw an article in the newspaper that nhtsa was investigating this component on the 1995 explorer and wished to provide my information as well.
A stud in the sway bar link assembly, was installed upside down and not torqued properly allowing nut to work loose and fail allowing assembly to fall completely free from vehicle.
Consumer lease car only had 600 miles the right rear shock came loose and make noise the steering shaft there is loose a lot of play.tt
1995 ford explorer overdrive light blinks. Resulting in $700 repair bill. In researching this problem it appears to be wide spread going over several model years.
Rear spring shackles on 1995 ford explorer totally rusted through. I have been very maintenance oriented since i purchased new.
The front driver's side tire has a large gash in it, firestone atx p235/75r15 105 s m/s, claim #24-5122-557.nlm
This accident occurred during rain and high wind.however, given the problems recently reported in the press i wanted to report the issue.the vehicle did roll over and both tires on the drivers side were blown out.i don't know the blown tire/tires caused or occurred as a result of the car rolling over.( dot number: )
Bought vehicle from my parents.tires were new tires due to ford/firestone recall.a second tire is now exhibiting a belt shift condition.symptom is a speed related tire noise similar to a flat spot on the tire but no vibration or bump is felt.first replacement performed free of charge by dealer.second failure to be looked at by goodyear retailer due to distance to ford dealer.goodyear retailer has advised of a prorated charge due to wear on tires.mr
Wilderness ht brand blew at 65 mph on expressway.i keep the air pressure at normal.no rubber left, no nails found, was riding on the rim.reported it to firestone dealer.i had to purchase a new tire, took out another warranty because i couldn't find the first receipt and firestone does not keep the warranty info in their computer system.how convenient.i have had continual problems with the front tires and need constant alignment.firestone said they could not find a problem twice, but i believe it is the tires.the ht brandis just as unsafe as the at and atx.the suv drives like it is always windy outside and the truck feels like it is hard to control.the recall needs to include the ht brand.( dot number: tire size: 23575r15 )
While driving across alligator alley (i-75) in florida in my 95 ford explorer around 8:30pm at a speed of 75mph with four well-kept inflated tires with no visual defects, the left rear tire tread pealed off from the core of the tire without warning or impact of any object in the road. My suvs rear end began to swerve, i was able to keep some control long enough to bring the vehicle to a stop with no injures. The only damage was to the car from the tread breaking way.( dot number: tire size: p235/75r15 )
While traveling at 69 mph, driver tried to avoid hitting a rv, suv rolled over and slid 50 to 60 feet upside down, it felted like someone or something picked up the rear end of suv.
On april 20, 1999 i had my 45,00 mile service performed at a local ford dealership in dallas, tx on our '95 ford explorer xlt.during that service visit the technician noted the steel core exposed on the left rear tire; after close examination of the defective tires it was noted that it appeared that the tire had blistered and burst the outer core.since this was well before (16 months ago) the firestone axt recall our only recourse was to place the tire(s).in a effort to not put myself or family at risk we elected to "bit- the-bullet" and purchased a complete set of new michelin tires at sam's wholesale store.i wish to be reimbursed along with the other customers who are offered replacement tires or being reimbursed for tires purchased after january 1, 2000.i feel that i was was victimized by firestone's misjudgment, but unfortunately at this time do not fall within there 'specified window' of replacement or reimbursement policy guidelines.any help you can provide me would be appreciated.i have contacted both ford motor company and bridgestone-firestone and have been passed on from phone number to phone number to no avail.i am very frustrated with both ford & firestone as to how they have handled this unfortunate situation with the general public as well as myself. (tiresize: p235-75r15)( dot number: tire size: p235-75r15 )
Firestone atx tire experienced an exposed steel wire on the inner edge of the left front tire, consumer is requesting reimbursement for the replacement tires and for anunnecessary alignment.
While driving to work on may 30, 2000, the firestone atx tire's outer surface split off from the rest of the tire.about 30% of the tread split from the tire resulting in damage to the rear wheel well body damage at the rear and tearing off plastic trim.this occurred on a particularly danagerous stretch of road through tijeras canyon east of albuquerque, new mexico.our son was fortunate to maintain control of the vehicle and get off the freeway to change the tire.when he took the tire to firestone tire at 9500 montgomery ne, albuquerque, nm 87111, tel: 505-293-4921, he was told he must buy a new tire and that he could mail the defective tire somewhere and then get part of it reimbursed.firestone implies that he must have been responsible for the damage.this tire and the four others on the explorer have been replaced this date with four new michelin tires.we want nothing more to do with firestone tires.the cost of replacing the tires was over $500 including tax, balancing, caps.firestone's recall and offer to replace tires of the same kind would be unacceptable to us.we have lost total confidence in this company.it is despicable that they have covered up the defects in their tires for this long and that people have lost their lives. They don't deserve to be in business.thank you for the opportunity to register our complaint. The timeim from the vehicle.casing.( dot number: vnhl p8 tire size: p235/75r15 )
The tire splitand i took it to a tire dealer and was told the tire was defective( dot number: tire size: p255/70r16 )
Right rear tire cupping.
I am concerned that my tires should be defective due to the type and size.at this time they are not specifically identified as defective but they are firestone wilderness ht tires built in decatur illinois. (dot number: vdhl awrtiresize: p235/75r15)
Fluid which was later confirmed to be oil from overflow tank spilled out on brakes on passenger side.i had to drive 2 hours back to north carolina because the dealership in galax, va closed at noon on saturdays.if i was by myself it would be a different story but i had my child with me.town and country ford confirmed the situation and stated that ford had sent out a memo saying if the vehicle was in warrantee the could put the cover on to prevent this problem but due to my mileage i had to pay $375.oo not including parts to have this taking care of.my question is if they put this device on and knew this could happen why not warn the consumer instead of finding out this way and why should i have to pay for a potential safety hazard which was not of my making.i called the 800 number on several occasions; got a claims number and that was it. The second time they said call town and country ford which the regional rep still hasn't responded. Next, i sent them a e-mail stating the problem and still no response. On the tires, which i had to replace myself, except for the spare which is a firestone, since the warranty was not honored stating that since they were only theywere only the stateside receiving dealership they were not responsible.the tires blew out less than two weeks after picking up the vehicle.i am very displeased with ford.according to the distance of travel i have resorted to renting so i would not have to worry about getting into an accident with my child in the vehicle.this is unacceptable and needs to be addressed.i can replace a vehicle but not a life.however, i refuse to pay for something which was already there to begin with.thanking you in advance for your time and attention in this matter.
When driving at 55 mph right rear tire blewout. Consumer unsure of tirebrand. However,tires wereoriginal ones.also, this was the second occurrence. Consumer has contacted the dealer. Please provide any further details.
I replaced my tires today because of noticeable cracking/tread separation.2 tires were very bad.i did not want to put my 2 year old child in jeopardy any longer by waiting for the recall on these tires.what documentation do i need to keep?do i need to get the dealer to note on my receipt that the old tires are cracked?i did not keep the old tires.the new tires were purchased at san benito tire, inc., 246 tres pinos rd., hollister, ca(831) 637-5804( dot number: )
One of originally installed 16 " firestone wilderness at tires in ford explore blew out prematuarly when we were driving on the south-bound of i-95 at conneticut on may 10, 1999. Fortunately, no accident was involved and no one was injured. We just replaced brocken tire to a new one at nearby tire shop. I have not reported to anyone then. This tire failure was obviously premature tire failure, which is the same to the one currently recalled on firestone tires. I brought the car for inspection at a ford dealer in virginia in late august, but they rejected to replace it since this is 16 inch tire and only 15 inch tires were recalled then. I am reporting that 16 inch tires of this tiye are also in danger as we experienced and those shall be recalled immediately to avoid future accidents. ( dot number: tire size: p255/70r16 )
Front end shakes and makes noises, difficult to control, and causes uneven wear to front tires due to misaligned front end. *dh
Right rear tire blow out causing the ford to flip several times. I received major injuries.i do not recall any information about the accident, except what was told to me.( dot number: uncu 1pl 0 tire size: p255/70r16 )
Was traveling on highway 59 south in texas, heading towards houston when i was existing off a ramp into a 360 degree curve when all of sudden the right rear tire tread separated and blew out.my ford explorer vehicle then spunned several times in a complete circles, however, due to a rainy conditions, the vehicle went into a sliding circular moition rather than flipping the vehicle due to loss of traction.my wife, daughter, son, and mother were the occupant in the vehicle when this incident happend.my mother was jarred and sustain a laceration to her lower lip and brusing of her face due to the sudden impact with the shoulder of roadway and a drainage ditch.on the second blowout of the same brand of tire, i was traveling north on interstate 55 in mississippi when i incurred another tread separation and blow out of the right rear tire which was also made by firestone..both tire were purchased in july of 1998, current mileage on the vehicle at time of purchase was 72,635 miles.i truly believe that these tires were defective and i replaced all of the firestone tires with the bridgestone dueller apt ii tires.still have reservation regarding these tires also being that they were manufactured by the parent company of firestone.( dot number: vnculpx208 tire size: 255/70/s16 )
Is there a poss. Recall , what do i dothank you. No safety defect mentioned.( dot number: tire size: 215 75 15 )
I have submitted a claim to firestone, and am awaiting their reply.( dot number: tire size: p235/75/r1 )
I was going down the road at 12:30 at night and it sounded like someone blew up the back of my car and when i got out of the car the back left tire was flat. (tiresize: p235/75r15)( dot number:tire size: p235/75r15 )
Consumer no longer owns this vehicle, but vehicle was equipped withfirestone atx tires.while driving at 55mphfront right tire blewout,causingvehicle to rollover. Dealer has not been contacted.
These 4 tires gave me horrible handling & vibrations which i tried to have fixed but couldn`t at hibdon tires of enid,ok( dot number: tire size: 2357515 )
We purchased new firestone wilderness at tires (p235/75r15) from our local costco tire center on 06-27-99.our tires do not have the recalled dot serial number, but we had them inspected at the costco tire center just to be safe.the tire installer at costco pointed out that both front tires had started to crack and separate where the tread meets the sidewall.we were told to replace the tires immediately.costco will replace the tires, but has to put on another pair of firestone wilderness tires.i repeat, our tires are not currently subject to recall, even though they are also defective.at the time of this e-mail, the tires only have 22,329 miles on them and the tread is in danger of separating.it is my belief that all firestone wilderness tires should be recalled immediately!if firestone knew beforehand about problems with their tires, they should be held criminally liable for any deaths and injuries associated with their tires.please add my name to the list of complaints about firestone wilderness at tires.( dot number: 8xhlipy tire size: p235/75r15 )
While traveling consumer was involved in a roll over.both passenger side firestone tires had blown.consumers wife sustained injuries to her head and back.*jg
Ford dealer that repaired the damage to the ford advised me that the tread had seperated and blown the tire apart.he pointed out that the three remaing tires had a crack around the ties where the tread attaches to the body, and sugessted that i take the car to firestone for replacement as they were defective.the firestone mgr examined my tires and agreed that all four should b replaced.he stated that he would have to order them and would call me when the came in.the tires came in and were installed june 28 1999.firestone did not replace the blown tire at no charge but gave me an adjusted pricecharging me 59.99 for each of 4 tires plus balance,new valve stems,tire disposal fee,road hazard warranty,pls shop supplys.total adjusted price 359.49 i was unaware at the time of the problem firestone was having or i would never have been agreeable to that deal.i have copy of tire invoices,work performed byjohnson brothers ford and road service to place spare on at time of accident.if you need more information please let me know.( dot number: na tire size: 25570r16 )
I was going down the road at 12:30 at night and it sounded like someone blew up the back of my car and when i got out of the car the back left tire was flat. (tiresize: p235/75r15)( dot number:tire size: p235/75r15 )
All 4 tires have cracks all around top edge of tire and in tread. Also cracks all around sidewall of tire where rim mounts. Tire dealer inspected tires and said they are dangerous and tread is ready to separate.need to take them to firestone dealer for inspection. Tires wore out to soon. Should have 10-15000 miles left based on tread depth. Took to firestone dealer and they said too bad. For $500 we will give you 4 new tires. They will only honor tires that are on recall list. He also said cracks need to be lower than they are on sidewall. Please help! all these wilderness tires are dangerous. Please put pressure on this manufacture so they can help people to feel safer on products they purchase. These tires are unsafe! (dot number: e4026555tiresize: p255/70r16)
This incident occurred twice -- once on the original firestone atx tires and then again on the replacement atx tires i bought to replace the originals. Both times a blowout of the entire sidewall. I no longer own this automobile.( dot number: )
Ford won't reimburse me for having my tires replaced because i had it done 29 days before they started their start date. Even though i felt our lives were in danger driving on those tires. (tiresize: 255/16)
1 tire had peeling tread, other3 have cracks in treads why not recalled?( dot number: w2hl tire size: 23575r15 )
Right rear tire shows definite signs of tread separation. Small hairline crack running around outside of tire about an inch down from top of tread. Left rear tire not as noticeable but on close examination shows signs of beginning to separate. Although tire size is not on recall list when inspected by firestone dealer they agreed to replace all four tires.( dot number: w2hl tire size: p235/75r15 )
Tread seperated from tire causing blow out. Good year dealership were tires were replaced said all 4 tires showed signs of cracking( dot number: vncu1pl035 tire size: p255/70r16 )
I identified the defective tires before they failed. 95% of each tire was like new, but the inside tread was warn down to the steel belts. I contacted ford, but they said the only thing they would do was look at it. I already knew there was a problem and declined their offer to "look at it!" after going through three sets of front tires in 75,000 miles, i convinced my front end alighment mechanic to set the angle of the alignment so that the tops of the tires were out 1/4 inch. This seems to have stopped the problem. I beleive that this was a design defect that was compounded by a flawed alignment specification. I'm sure that i would have experienced a blowout, if i had not performed my own oil changes and kept such a close eye on the tire wear.( dot number: tire size: p22570r15 )
My three other tires were also separating and were replaced.i am still waiting for firestone to pay me for my medical and eight months loss time from work and vehicle rental.they had reimbursed me approximately $2,700.00 only for damage to my explorer.the tires they had replaced i believe now has a recall according to the new reports of 5-21-01.if you can give me some assistance it would be greatly appreciated. (dot number: w2hl1pm135tiresize: p235/75r15)
Driving on cool day on mass. Pike east of sturbridge exit.tire separation. Heard thumping prior to sudden flat.sidewall blew out.tread came off in streams.tires were new when vehicle was purchased.( dot number: tire size: 235/75 )
On may 9, 1998 my husband and i purchased a used 1995 ford explorer from hooks ford in granbury. At the time of purchase my husband commented on one of the tires. The salesman assured us he would have the service dept. Check the tires. After merely "rotating" the tires, they declared it safe. Three days later, may 12, 1998 while driving home to austin, the rear driver's side tire blew out and caused the vehicle to flip over and roll 5 1/2 times. A four year-old child was thrown through a window and survived. A second child restrained in a car seat was physically unharmed. The driver, myself, remained in the vehicle as it rolled but my seat belt failed and i sustained a compression fracture of my neck, laceration of my head and ear, and went into a coma. We reported the incident to the dealership and to ford and never heard back from either. We consulted an attorney and because we no longer "had" the vehicle in hand, he couldn't prove anything. My husband was following the explorer in a u-haul and watched the entire incident. This accident changed my life, as i sustained permenant injuries. Our family was devistated. If there is every a class action suit or anything we could do to prevent another family from enduring what we went through. Please let us know! we do have pictures from the accident and proof i was wearing my seat belt, which failed. We do have a photo of the tire that blew, causing the wreck.
Since purchase of vehicle in 1998 following components had to be replaced: transmission/fuel pump/ all 4 tires blew and not on recall/ cruise control/radio quit, and no longer able to buckle drivers seat belt.*et
The left rear tire came loose causing the tire to blowout, the driver applied the brakes and lost control and veered partially to the center median, the driver overcorrected to the right which turned the vehicle at a sideway angle then became airborne and landed on its top right side, the vehicle then slid and rolled about 5 times across the road before coming to rest on its top, both rear passengers were ejected, the two left side tires were detached from the axles at rest(texas peace officers accident report, bridgestone/firestone, p235/75r15, radial atx m/s, w2hl1pm215, left rear).nlm
The defective firestone atx tires failed causing the vehicle to rollover while driving, as a result the seat belts failed to properly restrain the driver causing injury to her back by breaking 8 vertebrae (attorney for client).nlm
When recall first started, i took vehicle to firestone dealer, was told my tires were not on recall list, was also told the seperating lines on my tires were caused from "heat stress & all tires do that!"i don't think so, not one of the four vehicles sitting in our driveway have the lines on them like these do!please check this out, very concerned about driving down the road & having tires blow out on me.thank you!!! (tiresize: 255/70r/16)( dot number: tire size: 255/70r/16 )
Repeated failures of firestone tires over 3 years. Reported to friestone w/ no action. This was about 2 weeks prior to the first major recall/safety announcement. Refused to warranty and claimed to have a new computer system that hd wiped out all info prior to jan 2000. Will f/u with letter to you. My apologies for the late report. Thought i had mailed the letter previously. Currently have spare tire firestone and will report to local ford dealer. (tiresize: standard)( dot number:tire size: standard )
In my opinion, the ford explorer and ford f series pickups have unusual front end harmonics problems, which causes premature and unusual tire wear symtoms.ford recommends to rotate tires at 6000 miles, on ford explorer, if you wait till 6,000 miles the tires will have unusual tire wear to the point that rotating the front to the rear, and hope the rear tires will correct themselves within next 6000 rotation will not occur.in other words,the ford explorer will wear tires to unusual limits within 6,000 miles to where rotation will not take care of the problem within the next 6000miles.i bought 4 brand new goodyear wrangler rt's at 28,000 miles, they needed rotated far before 34,000 miles, goodyear said wait until the 34,000 miles which i did.i rotated the tires again at 40,000 miles and traded vehicle off at 41,000 miles.the tires were of good tread but worn in a crazy fashion in an irregular manner.4 new shocks did not help, the ford garage checked the alignment and stated the vehicle was within specs.i bought a ford f-250 with goodyear at's, and it to seems to be wearing the tires funny.ido not drive erratic and do keep the tire pressure to the recommended psi.for years, when ford had the twin i-beam front suspension on its p/u's, the tires wore funny and alsowould not last till the 6000 mile rotation point.ford has had a problem with very unusual tire wear for years, and it must be with ford's suspension system, weight to ground pressures or harmonics, but they have a very serious design flaw which effects its tires towearunusally on the ford explorer series and the ford f series, this is a certainty.the problem does not just effect firestone tires!!!!!!!( dot number: tire size: p235r75-15 )
The tire splitand i took it to a tire dealer and was told the tire was defective( dot number: tire size: p255/70r16 )
Firestone atx 15" tire experienced blowout and also caused damage to the rear chrome panel and right rear chrome molding, the consumer is requesting reimbursement.
Tire failure.
I had to have this repaired in the summer 2000 because handling was extremely bad especially at high speed (over 45mph) and going around curves.it felt like the vehicle was going to roll over.the repairs were made at a garage and not at a dealer.
Prior to accident i could not keep the tires balanced.i also had the 16 inch tires fail on my 1998 explorer.i could not keep them balanced and they would bounce all over. I replaced them with michelin tires.( dot number: tire size: 16 inch )
Left rear tire blow out ,no tread seperation ,vehicle rolled over.(tiresize: 245-16)
Consumer discovered a slow leak in one of the tires (fireston atx radials) upon inspection of all the tires noticed they are cracking along the outside although the mileage of the vehicle is low.nlm
No summary( dot number: tire size: p235/75r15 )
Consumer states tires have been replaced once.*nlm
Original equipment on a 1995, explorer, p255/70r16 size.all fourfirestone wilderness at tires are crackingon the tread and sidewalls.ford and firestone have been notified.dot # vncu1pl145
The front passenger side tire tread separated while driving, on another occasion the the rear drivers side tire blew out causing the driver to lose control of the vehicle and ended up in a grassy median, in july of 2000 prior to the recall 00t005, consumer had to replace two more tires due to bad belts,consumer is requesting reimbursement for faulty tires (firestone wilderness atx, p235/75r15).nlm
Hate firestone, they replaced recall tires with at's.had atx.we also paid $200+ to have them put on 4 new shocks. Said if we not happy they will replace with anything we wanted.would not have accepted the at's if he hadn't said we could get replaced if not happy. Contacted them and asked for goodyear or michellin's. They have brushed us off.heard some got $500 to replace tires anywhere they wanted but since ours have been replaced once, afraid we will not be reimbursed.current tires are very hard ride and cause car to dash lights to go out, and car isn't as steady on the at's.these 4x4 at's seem to want to hunt and not good in mud. Live in country and use 4 wheel drive often. Hate these tires. Will never buy firestone tires again! ( dot number: tire size: p23575r15 )
Firestone atx tire experienced an exposed steel wire on the inner edge of the left front tire, consumer is requesting reimbursement for the replacement tires and for anunnecessary alignment.
Right front firestone tire failed causing the consumer to loose control of the vehicle, hit the left shoulder and rolled over 3 times.nlm
No summary( dot number: tire size: p225/70r15 )
Consumer saw a 6-7 inch crack in the front left firestone wilderness at tire p255/70r16 dot vncu1pl in the sidewall, the other tires had hairline cracks on the edge of the outside tread, these tires dot # is st358j, dealer stated the hairline cracks came from dryrot, consumer replaced tires on his own due to no help from firestone and ford because these specific tires were not on recall.
No summary( dot number: )
Tread separated - almost rolled vehicle( dot number: tire size: lt 235r75 )
I had 2 of 4 tires that were separating, i replaced them with the advise of a tire dealer (discount tires inc) i realize this was before the tire recall, but they were replaced because of a failure. I have submitted an invoice to firestone for reimbursement, but have not heard from them. I also have a spare tire that falls under the recall and i will take this to the firestone dealer for replacement. (tiresize: 23575r15)( dot number: tire size: 23575r15 )
Original tires, dot vncu1pl494, 22570r16. Two driver's side tires had bubbles in them, showing premature tire failures. Firestone wilderness at.
Firestone is replacing tires with centenial canyon climbers.
I cannot read the dot number, but the tires were manufactured in canada.the failure that occured was as follows: left front tire completely deflated after driving ~150 miles at 65 mph on interstate 81 in va.no puncture was found, however air was leaking from large cracks that appeared at the tread line.similar cracks were observed on the front right tire, although it did not deflate.both front tires were replaced with the same firestone tires on 6/1/2000.the rear tires are now developing cracks in the same locations.( dot number: tire size: p255 70r16 )
We "did not" feel "safe" with these tires on our vehicle.we talked to representative from the hotline and he gaves us the okay to get new tires and send in the forms.well we went and got the new tires and sent in the paper work, and we got back a letter saying, "we have reviewed the entire file and unfortunately, we must respectfully deny your request for a refund.we are unable to process your refund for one or more reasons: the type of tire you requested replacement/reimburstment forwas not part of the voluntary safety recall" we have also writen them a letter stating that theywere not satisfing all their customers.please help me. (dot number: w2hlipy308tiresize: p2357515)
In my opinion, the ford explorer and ford f series pickups have unusual front end harmonics problems, which causes premature and unusual tire wear symtoms.ford recommends to rotate tires at 6000 miles, on ford explorer, if you wait till 6,000 miles the tires will have unusual tire wear to the point that rotating the front to the rear, and hope the rear tires will correct themselves within next 6000 rotation will not occur.in other words,the ford explorer will wear tires to unusual limits within 6,000 miles to where rotation will not take care of the problem within the next 6000miles.i bought 4 brand new goodyear wrangler rt's at 28,000 miles, they needed rotated far before 34,000 miles, goodyear said wait until the 34,000 miles which i did.i rotated the tires again at 40,000 miles and traded vehicle off at 41,000 miles.the tires were of good tread but worn in a crazy fashion in an irregular manner.4 new shocks did not help, the ford garage checked the alignment and stated the vehicle was within specs.i bought a ford f-250 with goodyear at's, and it to seems to be wearing the tires funny.ido not drive erratic and do keep the tire pressure to the recommended psi.for years, when ford had the twin i-beam front suspension on its p/u's, the tires wore funny and alsowould not last till the 6000 mile rotation point.ford has had a problem with very unusual tire wear for years, and it must be with ford's suspension system, weight to ground pressures or harmonics, but they have a very serious design flaw which effects its tires towearunusally on the ford explorer series and the ford f series, this is a certainty.the problem does not just effect firestone tires!!!!!!!( dot number: tire size: p235r75-15 )
Firestone atx 15" tire experienced blowout and also caused damage to the rear chrome panel and right rear chrome molding, the consumer is requesting reimbursement.
Three of four wilderness at tires were originals.all original tires found to have a visible separation between the tread and belt around the entire circumference of the tire.tires had normal wear with plenty of good tread left;although, the tires are five years old and have 67,000 miles on them. (dot number: vncu1pl165tiresize: p255/70r16)
While driving on the atlantic city expressway, the rt rear tire blew out.it was not a tread separation.the tire was a replacement, but was the same as the original equipment.no injuries occurred.the incident is reported now because of recent news of questions regarding explorers equiped with goodyear tires.i no longer own this car. (dot number: unknowntiresize: 225r16)
Tire label states 26 psi which is incorrect, recommended psi is 35.this error resulted in tires being under inflated, causing tires to cup.
Tire numbers: 105s m/s; 20958urbw062(2)1; e4 02 6556. No safety defect listed in summary.( dot number: tire size: p235/75r15 )
The front tires blew out while driving on the highway at an approximate speed of 50-55 mph. As a result i lost control of the car which flipped over the guard rail and rolled down a 70 foot ditch. I was in the car and was severely injured, sustaining permanent external injury (i.e., scarring) and internal (i.e, headaches, backache).( dot number: tire size: 255 16 )
Owner requesting information on tire failures (firestone atx.)
While driving at 65 mph driver noticed vehicle was leaning ,noticed tire was flat , it had separated. Pieces of tire were still on rim , causing safety hazard.
No summary( dot number: )
Two weeks ago we brought the car to a firestone dealer for the recall.they put us on a waiting list and said not to worry, they looked at the tires and they were fine.yesterday my wife was driving on the freeway and the tire came apart.she narrowly avoided an accident as she was slowing down to exit the freeway.upon inspection, the tire had a major hole from separation, not from any foreign object.today we bought new tires because the firestone dealer still did not have any replacement tires.( dot number: tire size: p235r15 )
I purchased these tires at vehicle mileage 111655, and the tires have a 50,000-mile warranty.i had to replace them at 150984 miles because of tread separation on the back two tires.mechanic's notes are "two rear tires separated.tread depth 2 at 12 & 2 at 10."description of tires -- wilderness at p255 70r 16 109s m/s (27951urbmo61755) made in canada.i was hoping that these tires would make it to the recall, so i have not submitted them for warranty replacement yet.i have the tires.i hope registration of this complaint is helpful to the mission of your organization.( dot number: vncu1p7079 tire size: p25570r16 )
On february 19, 2000, ed carney ford refused to exchange my recalled firestone tires because they were not currently mounted on my vehicle and i had other tires on the car ... This despite presenting the recalled tires at their dealership that day.the ford motor company has since confirmed to me that the dealership acted improperly, and that tires affected by the recall are to be exchanged whether they are currently mounted or not.i believe this is a serious breech of ed carney's responsiblities in this recall, warranting this complaint, and i hope that the nhtsa will take active steps to ensure that they do not try to scam other customers this way in the future.
Left rear tire blewout while driving causing sudden loss of control and resulting in vehicle damage and bodily injury (firestone atx 15").nlm
Left rear tire tread seperation, causing vehicle to immediatly and very radically fly, bounce and roll numerous times off the highway.( dot number: tire size: 16 )
While driving the front right tire blew, front side of vehicle came down so hard, crushed chrome rim and bent frame (tire make not provided, tire size p25570r16). Cj
The vehicle experienced three blowouts in one week (goodyear wrangler).nlm
The left rear tire came loose causing the tire to blowout, the driver applied the brakes and lost control and veered partially to the center median, the driver overcorrected to the right which turned the vehicle at a sideway angle then became airborne and landed on its top right side, the vehicle then slid and rolled about 5 times across the road before coming to rest on its top, both rear passengers were ejected, the two left side tires were detached from the axles at rest(texas peace officers accident report, bridgestone/firestone, p235/75r15, radial atx m/s, w2hl1pm215, left rear).nlm
I purchased these tires at vehicle mileage 111655, and the tires have a 50,000-mile warranty.i had to replace them at 150984 miles because of tread separation on the back two tires.mechanic's notes are "two rear tires separated.tread depth 2 at 12 & 2 at 10."description of tires -- wilderness at p255 70r 16 109s m/s (27951urbmo61755) made in canada.i was hoping that these tires would make it to the recall, so i have not submitted them for warranty replacement yet.i have the tires.i hope registration of this complaint is helpful to the mission of your organization.( dot number: vncu1p7079 tire size: p25570r16 )
Complete # on tire is atx firestone/bridgestone p235/t5r151055m+s. No safety defect mentione din summary.( dot number: tire size: p235/tr15 )
Firestone wilderness tires blewout on the rear left side while traveling at 65 mph. Ford was contacted. Firestone atx p235/75/r15
I had just come off the freeway, when the front right tire threw its tread off, i pulled to the side of the road and changed it to the spare tire. Later on i had all 4 tires replaced.( dot number: tire size: p235/75/15 )
Was traveling on highway 59 south in texas, heading towards houston when i was existing off a ramp into a 360 degree curve when all of sudden the right rear tire tread separated and blew out.my ford explorer vehicle then spunned several times in a complete circles, however, due to a rainy conditions, the vehicle went into a sliding circular moition rather than flipping the vehicle due to loss of traction.my wife, daughter, son, and mother were the occupant in the vehicle when this incident happend.my mother was jarred and sustain a laceration to her lower lip and brusing of her face due to the sudden impact with the shoulder of roadway and a drainage ditch.on the second blowout of the same brand of tire, i was traveling north on interstate 55 in mississippi when i incurred another tread separation and blow out of the right rear tire which was also made by firestone..both tire were purchased in july of 1998, current mileage on the vehicle at time of purchase was 72,635 miles.i truly believe that these tires were defective and i replaced all of the firestone tires with the bridgestone dueller apt ii tires.still have reservation regarding these tires also being that they were manufactured by the parent company of firestone.( dot number: vnculpx208 tire size: 255/70/s16 )
Tire blow-out on 2 yr old car with 32,000 miles with no apparent reason. Immediately replaced tires, with michelins at cost of $500.still have paperwork.with all the accidents and fatalities associated with these tires, has there been a class action suit filed against ford and firestone?if not, what is my recourse for recovery of money spent now that problem with these tires have been surfaced by other motorists. Thanks, r. Vaughan.....p.s. Please give my regards to general wykle.( dot number: unk tire size: p235/75r15 )
This report relates to the current tire problems with ford explorer vehicles.my previous letter to nhtsa is dated 13 may 1997. You need to go back and reread this letter. Ford motor company is deliberately and flagrantly putting incorrect tire pressure labels into all ford explorer trucks. The reason is that the truck "rides better" with lower tire pressure (26 pounds). Fords own mechanics will tell you that you need at least 35 pounds of air pressure to avoid premature tire wear.then when you go back to ford and try to get them to replace your damaged tires (if they don't fail first), they "stonewall" all your letters and phone calls. Trust me, because i went thru the whole process and got no where with ford.they don't care about premature tire wear or damaged/unsafe tires, they just want a nice soft ride in order to keep selling ford explorer trucks. If you put the proper air pressure into the tires (35 pounds), the truck rides hard and rough due to the suspension system. You folks need to check this out, ford is literally getting away with murder here.arj
On april 20, 1999 i had my 45,00 mile service performed at a local ford dealership in dallas, tx on our '95 ford explorer xlt.during that service visit the technician noted the steel core exposed on the left rear tire; after close examination of the defective tires it was noted that it appeared that the tire had blistered and burst the outer core.since this was well before (16 months ago) the firestone axt recall our only recourse was to place the tire(s).in a effort to not put myself or family at risk we elected to "bit- the-bullet" and purchased a complete set of new michelin tires at sam's wholesale store.i wish to be reimbursed along with the other customers who are offered replacement tires or being reimbursed for tires purchased after january 1, 2000.i feel that i was was victimized by firestone's misjudgment, but unfortunately at this time do not fall within there 'specified window' of replacement or reimbursement policy guidelines.any help you can provide me would be appreciated.i have contacted both ford motor company and bridgestone-firestone and have been passed on from phone number to phone number to no avail.i am very frustrated with both ford & firestone as to how they have handled this unfortunate situation with the general public as well as myself.(tiresize: p235-75r15)( dot number: tire size: p235-75r15 )
While returning from vacation, i was traveling north on hwy. 75 in howe, tx, at 70mph when i heard the tire begin making noise and then it blew out. The blowout caused me to swerve uncontrollably (90 degrees to the road 3 times, across both lanes) before regaining control and allowing me to get safely off of the highway. There were luckily no other cars in the immediate area at this instant. The tire tread had separated from the casing and shredded. Also in the car were my wife, 17 year old daughter, and my daughters friend. The tire caused damage in the wheel well/rear quarter panel and rocker panel area of the car as well as cracking the rear taillight lens and damaging the aluminum wheel.( dot number: vduujba227 tire size: p225-70r15 )
Tread seperated from tire causing blow out. Good year dealership were tires were replaced said all 4 tires showed signs of cracking( dot number: vncu1pl035 tire size: p255/70r16 )
I replaced my tires today because of noticeable cracking/tread separation.2 tires were very bad.i did not want to put my 2 year old child in jeopardy any longer by waiting for the recall on these tires.what documentation do i need to keep?do i need to get the dealer to note on my receipt that the old tires are cracked?i did not keep the old tires.the new tires were purchased at san benito tire, inc., 246 tres pinos rd., hollister, ca(831) 637-5804( dot number: )
Pe00 020;consumer was traveling about 65mph onhighway and heard a bumping noise.right rear tires separated fromwheel. Consumerlost control, vehicle slid into an enbankment and ran into a tree. Firestone radial atx p235/75/r15 *mw
Vehicle felt as if someone/something pick up the rear end and started guiding it toward the right hand lane.after an uncontrollable ride, the vehicle ended up in the left lane and the suv rolled over and slid 50 to 60 feet up side down, vehicle finally came to a stop up sid down.i rolled down the driver window to get out, the passenager window blew out. Due to a tire blowout and peeled like a banana, suv totalled.
No summary listed for abov eehicle.
I was driving in town at 35 mph when tire suddenly deflated when tire was taken off a split in the sidewall that ran into the tread was found( dot number: vdhl awr tire size: 235/75/15 )
Original equipment on a 1995, exlorer, p235/75r15 size.sidewall cracked on two of the five tires.sidewall failed bycrackingand goingflat.
Original equipment, tread is in good condition, but all four tires have developed cracks aroundsidewall. Tire size p25570r16, wilderness at.dotvncu, consumer has had 2 flat tires.
Pe00020;original tires on a ford, explorer, 1995, 25570/r16, dotvncu1px029.sidewall had cracksabout inch long, anddriver could see the steel belts.every other inch had a crack. Also,all 4 tires had cracks, consumer replaced tires with wilderness at,and at 18, 000 miles consumerwas noticing more cracking.
Upon taking delivery noticed out of balance condition, had them balanced but still there, while traveling on ny tpk. At 60 mph l.f. Sidewall blew out. /replaced all tires and no more vibration. /goodyear dealer didn't replace. (tiresize: 205r15)( dot number:tire size: 205r15 )
Left front tire went flat while vehicle wasparked. Had only 50,000 miles on it. Took to discount tire retailer, and it was replaced.tire was destroyed. Onother 3 tiressidewalls were separating. Firestone, wilderness atx,p235/75r15.
Two goodyear wrangler tires (size: lt235/75r15, dot#: t300863grf-92w) on1995, ford, explorer have experienced sidewall problems. Left front tire has a two square inch section that has started tearing off of the sidewall with approximately 25,000 miles on the tire.also,left rear tires sidewall is beginning to split with 25 to 30,000 miles on the tire.these tires are not original equipment for this vehicle.
Spare tire too small.
Spare tire is smaller in width and in diameter than regular vehicle tire. Spare tire size is p22570r15 while regular tire size is p25570r16. Consumer called and asked a firestone dealer was this safe and dealer stated that it was not safe to drive with different size tires on vehicle, consumer was also informed that doing so could ruin the differential. Consumer stated that according to ford, this is standard equipment.
The spare tire is 15 inches, but truck was ordered from ford with the 16 inch tire and wheel package. The dealer and manufacturer is aware of the problem.
Consumerreplaced all4 tires due to tread separation with only 43000 miles on vehicle, firestone atx p235/75r15, dot w2hl1pm205, firestone is denying consumer a refund since consumer replaced tires prior to january 1, 2000.
Peooo20; not original tires on ford explorer, 25570r16. After 2000 miles right front tire had a knot on the side. Ford motor company failed to inform the customer the correct tire pressure to use for 16" tire.
Vehicle was parked. Steel core was coming throughtire.tread compound was cracked all around. Took tire to shop for replacement of all tires, eventhough 2 front tires had problems. Do not have tires.
Front driver side firestone tire rotted which was odd because the tire still had a lot of tread, the front passenger tire shredded and seperated, both back tire need replacing also
The vehicle experienced a tire tread separation (blowout) whiled driving, the consumer had all four tires replaced with another brand one day before the recall was announced (dec 31, 1999), the consumer requested reimbursement but was denied because the tires were purchased prior to january 1, 2000 (firestone atx).nlm
Original firestone atxtires, p23575r15 vnhlipm225. All 4belts were slipping, causing car to go to right or left. Consumer replaced all four tires.firestone denied consumer refund because he purchased the tire prior to august 8, 2000.
Pe 00-020; original tires on ford explorer 1995 p23575r15. Cosnumer was driving at approximately 65-70 mph whenrear right tire tread separated and then blew out. The tire was used for only 7300 miles.firestone claimed it road hazard.
Firestone radial atx tires experienced tread separation, ripping the rear of the vehicle on both occasions.
Rollover accident occurring on california highway at 70 mph due to the disintegration of the rear drivers side tire.( dot number: )
Firestone wilderness at tires (p255 70 r16) experienced belt separation and a blowout.
While driving home from a trip a passing car indicated to me a tire problem.i pulled off the road, called aaa and had my spare put on my ford explorer.about a week later i took the tire in to get it fixed.the manager of the firestone store where i took it called me over after inflating the tire on a stand.the tread had separated from the sidewall of the tire.he called his office who authorized a 50% reduction in replacement tires which i accepted but called firestone to request 100% replacement cost.to date no reply from firestone.concerned that other tires may have this problem.do not have the dot code but do remember that the tires were made in canada. (tiresize: 255/75x16)( dot number:tire size: 255/75x16 )
Not theoriginal tires on ford explorer 1995.front driver's side and rear passenger's side tireshave slow leaks, consumer is concerned that they may become flat or blowout.two tires have slow leaks and the tires are on recallbut customer has beenwaitingfor 2 1/2 months to get it fixed.
The consumer is having difficultly getting reimbursement for faulty firestone tires because she does not have the serial numbers of the tire because they were disposed of by the tire dealer, the tires had early signs of tread separation which caused noise while driving (firestone atx).nlm
Firestone wilderness at tires experienced cracking along the tread edge, consumer wants reimbursement.
Consumer had tire come apart prior to recall 00t-005 and replaced all four tires.nlm
Consumer has replaced firestone tires twice for a total of eight tires due to recall 00t005, firestone has not yet responded back to consumers request for reimbursement, tire size is p235/75r15.
Tire blew. Firestone atf wilderness (recall from ford & firestone) tire that blew was a firestone atf wilderness tire (re:tire recall from ford & firestone); looks like salv. Sold within the last couple of days up in memphis; agt. Indicates our insd. (an engineer) has several photos of the tread separation and is willing to provide these to us; kim. (claim# 53-p012-511) *mw
In june i replaced two tires.appeared belt separated - resulting in excessive wear in spots.current tires have fine cracks all around tires near rim.( dot number: vnhl tire size: p255/70r16 )
Pe02000, tire tread separation: while driving at 55 mph, tread on the driver's side rear tire came off and wrapped around the axle. Driver was able to control vehicle, and was nothurt.no other passengers were in the truck. Tire was a firestone, wilderness, not original equipment. Tire mileage was about 20,000. Tire was sent to firestone. Owner was sent a check for a new tire and to cover damages to truck. Please list dot # .the firestone dealer paid for one new tire and damage to the vehcile.the rest of the tires were replaced by the customer.
Consumer tires were included in recall 00t-005 but there were not parts available for replacement, consumer replaced tire with competitors brand and request compensation (firestone).nlm
Firestone radial atx tires (p235/75r15) experienced a blowout and vibration, consumer received recall notice 00t005 and replaced all tires and is requesting reimbursement.
Vehicle was being operated on us60 (freeway) in mesa az at approximately 60 mph in the center lane of a 3 lane roadway.all was normal with no vibrations.there was an instant bang with immediate onset of major vibrations and the vehicle pulled initially to the left and then back to the right.there was traffic to the left front and right rear at the time of the event.when traffic cleared the vehicle was pulled off to the right shoulder.the right rear tire had lost all but a 1 inch strip of the tread surface over the complete circumference of the tire.the tire still had air pressure and due to the shoulder hazard on the freeway, the vehicle was driven to the next exit where the tire was changed in a parking lot.there was obviously a very large piece of tire rubber that was thrown out into traffic and not recovered.it is fortunate that this was rather late hour with little traffic.had this event occurred during rush hour with solid traffic it would almost certainly have resulted in secondary damage or collateral accidents. Has this type of tire disintegration been a reported hazard for this type of tire in the past ?this mishap was reported to the firestone tire co. And they requested that the tire be returned to bfts,1515 elm hill pike #405,nashville, tn.37210-3615;case # 017918.the tire was shipped via ups on 08/04/99,package id: 106576,tracking ref: 1z85e4270310251306.( dot number: vnhl1pm474 tire size: 23575r15xl )
Consumer noticed that all 4 tires were experiencing tread separation.
Firestone apx tires on rear driver side blew out due to tread separation, causing a loss o vehicle control. Rubber from tire also caused damage to wheel well.
Since ownership, tires have caused vehicle to ride rough. Consumer replaced all four firestone atx (p235/75r15) tires when separation started to occur.consumer received recall notification, however has not received reimbursement as of 3/25/01.
We suffered a sudden tire failure on the left rear wheel while traveling northbound on i10 between tucson and phoenix and towing a 1970 vw beetle.just prior to the tire failure, i felt something was not right, so i stopped the vehicle on the shoulder of the interstate and inspected the hitch, the vw beetle and the rear tires on my explorer and found nothing of concern.as i was getting back up to speed, the tire tread on the rear left tire came totally off and the explorer felt like i was driving on ice, essentially no steering without danger of losing control.i stabilized the vehilcle but it gradually slide to the left and i sensed that if i tried to correct the car would go out of control. Fortunately, i was in the right lane on a two lane highway with no one around but i the car gradually move to the left slowing slowly; when the beetle caught the shoulder gravel we launched into to a roll over.we rolled twice and landed upright and the treadless tire was still inflated.towing the beetle provided a substantial amount of drag slowing both vehicles lessening the severity of the explorer's roll. When the beetle broke loose during the roll it took a lot of momentum with it as it rolled much further than the explorer causing the explorer to hit on both roof edges on subsequent rolls and landing on the tires without the airbags deploying; both passenger were wearing seatbelts and despite sprains, bruises and scratches we walked away from the accident.however, both cars were totaled and contents damaged and lost.a few weeks before this, i had the front tire develop a severe bump and took it to my local firestone dealer and bought new front tire and asked them to check the rear tires which still had plenty of tread depth which by the way the front tire that developed the bump also had plenty of tread left.firestone dealer assured me the back tires did not need replacing.( dot number: )
Prior to recall 00t-005 and 00v-402 the vehilce experienced sudden loss of control, the consumer believes the sway bar links malfunctioned causing the loss of control and that the tire also blewout during this accident, the consumer suffered a busted and swollen lip and body aches (firestone).nlm
Pe00.020; she was traveling about 65mph on highway and vehicle started to vibrate.she pulled over to the shoulders, andrear left tire tread had separated. Firestone, wilderness #at, p23575r16.there were no injuries.tookvehicle to firestone, and the attendanttold her that the tires weren't on the recall campaign.
Firestone wilderness/at p25570r16 tires on this vehicle developed a bubble on the side of the tire, insidetread while traveling at 60 mph, and a small piece of another tire fell out of the sidewall.dealer has replaced the tires.
Vehicle was involved in an accident due to faulty firestone tires (p255/r16), consumer stated that the tires have problems with skidding and tread.
Tread came off of tire while the car was in motion.we looked into purchasing two of the same tires but instead got four new tires from a different company.we are certainly happy that we made that decision in the light of what is being brought to our attention now.be advised we would like repayment for our expense of the new tires.( dot number: )
Firestone: insureds tire blew out, he lost control of the veh, the veh flipped over she has the receipt at home. She will send it to us via fax. She purchased the tire in fla. It was a new tire and now she is told that it may have been a recapped tire. Insd still has tire. She purchased the tires 2/99. (claim# 11-3354-635) *mw
While driving about 75 mphleft rear tire hadtread separation. Vehicle was wandering around the road.firestone, wilderness at, p235/75r15, dot hyhl1p458. Failure caused damage to the aluminumwheel.
Pe00040, tire tread separation: whle driving about 45 mphtread on one ofrear tires came off. Driver was able to maintain control, and was not injured. Tire size lt23585r16, dot # vdortwt. Original equipment on a 1998, ford, f350. Firestone has not been notified about this matter. Please provide any further information.
The owner is experiencing difficulty with firestone to replace his four defective firestone tires, prior to this recall the owner experienced a blowout. Nlm
About two month ago consumer had found out that tires were cracking. Tires were not listed on the recall.
What are the chances of sub recovery on a firestone atx tire failure with only a photo of the tire? it appears the belt separated. Thanks...shane (claim 43-r340-135) *mw
Tread separation from the firestone atxii tire was the possible cause of a vehicle rollover, there was one fatality and one injury due to the accident. (attorney for client)
Tread separated from body of tire( dot number: vncu ipl 1 tire size: p255/70r16 )
While driving about 70 mph left rear firestone atx tire exploded. Consumer maintained control of vehicle. This was the third time this happened. Tire size t235/75r 15.
Consumer experienced a flat, and when vehicle was take in, was advised by mechanic that the flat was due to tread separation, consumer has replaced all 4 firestone at(p255/70r16) tires.
While driving the right front tire tread separated from the tire, the consumer requested reimbursement for all tires replaced but was denied reimbursement because the replacement tires were purchased prior to the cut off date (firestone radial atx, p235/75r15 dot#w2hl-1pm-105).nlm
The consumer was driving onhighway and anotherindividual had signaled to him to pull over.when he pulled over, he noticed that tread on rear tires came off. Vehicle came with firestone atm tires#p235/75r15105s.
On sunday, august 20, 2000 my family and i were driving in our 1995 ford explorer when the tread on our firestone p225/70r15 detached from the tire. I was able to keep my suv under control and no additional damage was incurred.the tire was original equipment on the explorer with 37,000 miles on the tires. I am very concerned that the tires on my suv were not part of the initial recall. I believe this indicates that the defect in manufacture is systemic to all your tire products. I have the tier but not the tread, as it is some where in pieces on the highway. I would like a quick resolution to this matter and request that you pay for the replacement the tires with qualified tires at a dealer of my choice. Please respond promptly, as i need my suv for immediate transportation.( dot number: w2uu 1mx tire size: p225/70r1 )
On 9/18/99, my father, husband, son and i were involved in a rollover accident on i-10 because of the tread separation on the left rear tire.as a result of the accident, my father was taken by helicopter to a local hospital where he died 2 days later as a result of his injuries.my son was not harmed, my husband suffered minor injuries and was transported by ambulance to the same local hospital, and i had very minor cuts and bruises.( dot number: )
Firestone at tire (p23575r15) tread separated from the rest of the tire and caused $1700 damage to the rear quarter panel.nlm
Had stopped vehicle to check tires and noticed tread separating onleft rear firestone tire with 32,000 miles on it. Drove to tire retailer andhad2 tires inrear replaced.p225/70r15 on 1995.dot# w2uu1mx.
We don't have the recall tires or a problem on our vehicle. But, rather suspect tread separation being caused by anti-lock braking system and disk breaks on all 4 wheels. This can cause more breaking/shear stress on the tread over time. Running at high-speed doesn't simulate breaking, particularly in heavy stop-go commuting which many vehicles are now being used for. Then when they are taken on long high-speed drives, the weakened tread is subject to failure. Testing should include anti-lock brake surging tests and radial break-load simulation.( dot number: )
Consumer received recall 00t005, however the firestone tires were replaced due to the tread on the outer edges of the tire were wearing and pulling away, consumer is requesting reimbursement.
Rear passenger's tire tread separated at 65-70mph, causingdriver to lose control.tire size p235 original equipment.prior to recall (00t-005) consumer replaced two firestone tires.the consumer wants to be reimbursed for the cost of two tires replaced before the firestone recall. Consumer also experienced noise when braking due to prmature wearing of brake pads and bad rotors which replaced.
Pe00 020; rear driver's side tire had tread separation. Firestone ,wilderness arx, p235/75r15.
Since these tires were officially recalled yesterday (8/9/00), we have contacted the dealer where we purchased the vehicle.they stated that it will probably take up to six months before we are contacted and can begin to rectify the problem.i feel this is unacceptable.my wife and children use this vehicle primarily and i am concerned about the dangers.is the information from the dealer correct?i have been trying to get through to the firestone hotline 800#, but cannot get through for any further information.any info you could give me would be appreciated.( dot number: tire size: p175r15 )
Firestone radial atx ii tires (p235/75r15) experienced an air leak between the tread and sidewall, the dealer recommended all tires be replaced, the consumer is requesting reimbursement for the 2 faulty tires.
While driving at approximately 55 mph inford, explorer, 1995 right rear firestone tire, size: p255/70r16, dot: vdcu1px019experienced tread separation. *note:vehicle was involved in a crash due totread separation. Vehicle classified as a total loss, and consumer'swife suffered nose/head injuries.firestone wilderness at tires.
Tread separated( dot number: vnuu80a tire size: p225/70r15 )
The tires began to separated which caused severe vibration while driving, the consumer replaced all four tires and request reimbursement (firestone).nlm
Going 70 thud thud thud and flat. Steel belt split.( dot number: tire size: p235/75r15 )
The tread partially separated from the front left tire at 70 miles per hour.it did not blow and i was able to slow and get off the highway.if it had blown i feel certain that we would have rolled in that truck. (dot number: w2uutiresize: 225/70 r15)
I no longer own this truck, hence the missing information.i was driving at high speed on a nice sunny 70- some degree day when a part of the tread peeled off and the sidewall blew out. I was able to steer to the shoulder and stop, with significant difficulty.i did not know this info might be significant until now.i was not in a southern state in hot weather. The tire was only six months old, i had ruined the original equipment tire at a construction site.( dot number: )
Firestone radial atx tire, tread separated while driving at 65 mph.dealer has not been contacted.
Consumer needed a tire patched, dealer would not patch tire because consumer was waiting for replacement tires due to recall 00t005 and said that having a new tire on the vehicle for a few weeks would be fine, consumer sent a photocopy of the receipt for reimbursement and is being denied because the original wasn't sent, consumer is requesting reimbursement for the road hazard warranty that is now useless and for the prorated cost of a faulty tire that was replaced.
Consumer has replaced firestone tires twice for a total of eight tires due to recall 00t005, firestone has not yet responded back to consumers request for reimbursement, tire size is p235/75r15.
Pe00 020; consumer traveling about 75mph onhighway and heard a loud noise.then,lost control of the vehicle, and it rolled three or more times on the highway. Left front tire tread separated. Tires were firestone wilderness #at, p23575r15.there were onefatalityand three injuries.
While this blowout did not cause injury, death or property damage it is of note that the explorer spun violently left and right. The tire tread separated and the low speed and wet roads prevented greater damages. The maintained tire pressure was a constant 30 psi or 4 psi above ford specifications. (tiresize: p235-16)( dot number: tire size: p235-16 )
Firestone radial atx tires experienced tread separation, ripping the rear of the vehicle on both occasions.
While traveling on i-90 at ellensburg, wa, in light rain and a temperature in the 30's, the right rear tire suddenly failed with complete tread separation, literally it was just a ball of wire and rubber.i have never seen a tire fail so completely.the tire easily had another 10,000 miles of tread left.had a tire on the front of the vehicle failed in such a fashion, i would never have been able to maintain control.as it was, we were swerving over both lanes before we could get the vehicle slowed down and stopped.i was so shook up by the incident i immediately went to a tire deal and purchased a set of new tires and they were not firestones!( dot number: tire size: p325/75r-1 )
Firestone wilderness at tires affected by recall (oot-005), tires replaced, owner seeking reimbursement.
While driving the tread of the tire began separating from both the front and rear tires, the consumer replaced all four tires prior to recall 005-00t and request reimbursement (firestone).nlm
Consumerreceived a recall notice on tires that had replaced before due to tread separation.replaced them with new tires.firestone p235/ 75 r15.
Pe 00020: was driving approximately 70mph whenvehicle started to vibrate before a loud noise was heard. Then, vehicle started swerving back & forth. Was controllable. Pulled to side of road. Checked tires andnoticed that right rear tire had lost all its tread & was shredded. Was original tire & was inspected.sizep235/75r15 with 64,000 miles. Firestone radial atx.
The tread on the right front tire separated and the vehicle went off the road and rolled 4 or 5 times.i was injured with bruses, scratches,and glass cuts in my face.i have contacted norma davis at firestone (800-543-7522),but she stated that i needed the tire for her to help.i have since had the vehicle repocessed, because my insurance(nationwide insurance co.)chose to repair the vehicle for $10000.after months of taking the vehicle back to the repair shop, i was told that nationwide would no longer be responsible for repairs caused by my accident.my credit is ruined and i can not get any help.i do not know where to turn.please help me if possible.thank you very much.( dot number:)
Consumer was traveling about 55mph onfreeway andwas going under/over path whenhe heard a noise andvehicle started to vibrate. Then, he pulled over and noticed thattread had separated fromtires. The vehicle has firestone tiresatx #@p235-/75rr15105s dot w2hl1pn.
Pe00 020;was traveling about 65mph onhighway andheard a noise.went home and parked the vehicle.next day noticed that half of the tread had separated from the tire.he tookvehicle to firestone, it was the front left tire. Firestone #atx p23575r15#dot.there were no injuries.
Consumer received recall 00t005, however the firestone tires were replaced due to the tread on the outer edges of the tire were wearing and pulling away, consumer is requesting reimbursement.
While drivng on a gravel road the tires shredded and the vehicle rolled over 3 times, the infant in the rear of the vehicle only sustained a cut on the leg the driver sustain injuries to the head, neck and arms (firestone wilderness at 15").nlm
While driving approximately 70 mphright rear tire treadseparated fromtire which caused extensive damaged tovehicle.the tire is a firestone wilderness at.tire size p235/75r15. Tires were purchased as replacements. Approximate 20000-25000 mileage.the tread separation caused damage to the vehicle.
The rear driver's side tire (firestone radial atx) suffered tread separation while operating at highway speed.this resulted in loss of control of the vehicle as it pulled severly to the right.attempts to regain control of the vehicle ultimately resulted in a roll-over.the vehicle was considered a total loss.( dot number: )
Pe02000 tire tread separation: while driving between 50- 60 mph, the tire on the rear passenger's side went flat. Driver was able to controlexplorer. One other person was in the explorer. No one was hurt. Tire was a firestone, wilderness, ht. Original tire equipment.please provide any further information.
Firestone wilderness at tires (p255 70 r16) went flat and experienced tread separation, consumer is requesting replacement tires.
While driving approximately 70 mphright rear tire tread was separated, causingvehicle to flip 3 times. Driver sustained injuries. Tires were the original ones whenvehicle was purchased. Vehicle was a 1995 ford truck explorer.please add addtional tire info.rmation, odi# 6141. Firestone atx p235/70/r15 *mw
Peoo 020; consumer was traveling about 70mph onfreewayandthere was a knocking noise coming from vehicle. He lost control, vehicle rolled twice across the highway. Right tire on the passenger side tread had separated from the wheels. There were sixinjuries, and everyone inside ofvehicle was transported to the hospital.tire size #p235/75r15/105fm+s, and#dot w2hl 1pm 105.firestone company in ohio has evaluated this tire last year, and they were aware of problem.
Recall 00t005000/tread separation: tire replacement for firestone, wilderness at, p235/75r15, dot# hxhl. Replaced on 15-sep-2o00 at 74,028 miles, and caused vehicle to vibrate. Taken to dealer for inspection, and informed consumer that three of the four tires were causing vibration due to tire hop. Firestone was not notified at this time. The firestone dealer replaced all 5 tires.
Tires suffered from curbing effect and consumer replaced them, dealer deemed consumer ineligible for reimbursement because the tires were purchased prior to jan. 1, 2000, consumer still requesting reimbursement (firestone atx ii p235/75r15).nlm
While driving,rear firestone atx tires that were purchased after market, had a tread separating which caused vehicle to go into a spin, resulting in body damage.the tread separation also caused damage to the vehicle.
V1 driving back to houston from louisiana when tread of tire came off causing veh to go out of control and hit a tree. Vehicle being towed back to houston to jack roach ford. Ni wants to pursue a claim against firestone. His tire came apart and caused him to hit a tree. Ni has copy of receipts were he replaced his tires with firestone tires. He has photos of his vehicle and the tire appears to have the same proble. (claim# 53-c438-456) *mw
Going 70 thud thud thud and flat. Steel belt split.( dot number: tire size: p235/75r15 )
In june i replaced two tires.appeared belt separated - resulting in excessive wear in spots.current tires have fine cracks all around tires near rim.( dot number: vnhl tire size: p255/70r16 )
Seeking reimbursement for replacement of firestone wilderness tires p23575r15 under recall (oot-005). Cj
Firestone radial atx ii tires (p235/75r15) experienced an air leak between the tread and sidewall, the dealer recommended all tires be replaced, the consumer is requesting reimbursement for the 2 faulty tires.
The front passenger side tire tread separated while driving, on another occasion the the rear drivers side tire blew out causing the driver to lose control of the vehicle and ended up in a grassy median, in july of 2000 prior to the recall 00t005, consumer had to replace two more tires due to bad belts,consumer is requesting reimbursement for faulty tires (firestone wilderness atx, p235/75r15).nlm
Firestone tires experienced vibration, thumping noises, and a tread separation, the consumer is requesting reimbursement for the replacement tires.
Firestone apx tire blew out due to tread separation, causing loss of vehicle control. Rubber also caused damage to wheel well.
Rear firestone atx tire came completely off while driving causing vehicle to rollover and slide 60 feet upside down, consumer sustained some glass in face, ears, some cuts around left eye and bruise from where seat belt restrained driver, consumer request reimbursement for damages suffered as a result of accident.nlm
Consumer was traveling about 65mph on the highway and he heard a noise .he pulled over and noticed a chunk of the passenger rear side tires came off.
Firestone wilderness at tires experienced cracking along the tread edge, consumer wants reimbursement.
Pe00020; tire tread separation:tire on the passenger's front side was showing signs of tread separation. It was a firestone,wilderness at, 16 inch.please fill in vin/ and list dot # and tire size.
On july 5, 2000, while traveling west on interstate 40, three miles east of grants, nm, the right rear tire blew apart.we were able to safely get off the highway. This was the third firestone tire that has blown or experienced tread separation on me.( dot number: tire size: 235x75r15 )
Firestone tires experienced vibration, thumping noises, and a tread separation, the consumer is requesting reimbursement for the replacement tires.
While driving about 60 mph right rear tire suffered a tread separation. However, consumer kept control of vehicle.firestone atx,235/75r15 .the tread separation damaged the right rear wheel and body panel of the vehicle, and the manufacturer reimbursed the customer for the damages.
Tread separation/defects all four tires after 7 months. (tiresize: 16)( dot number:tire size: 16 )
Tire: belt separated on firestone, wilderness/at tires, p255/70r16 onford, explorer, 1995.ford/firestonehave been contacted. Dot # vncu1pl015, the tread separation caused damage to the vehicle.
Consumer replaced firestone tires prior to recall 00t005 and is having trouble seeking reimbursement.
Firestone wilderness tires on vehicle, inquire about possible recall as tires were cause of insd losing control, tires only 2-3months old. (claim# 42-1277-959) *mw
Consumer had an accident when the firestone at tire separated causing slight damage to the rear passenger side door, consumer request reimbursement.nlm
Pe00020, tire tread separation: while driving about 60 mph,tread on the driver's rear side tire came off, causingvehicle to roll over.driver was alone and was not injured. Tire size p25570r16.vehicle was totalled.firestone was notified through e-mail about the tire. There was no reponse from firestone. Please provide any further information.
While driving about 70 mph left rear tire blewout, causing vehicle to rollover. Firestone wilderness tires, sizep225/70r15.
Abs failure on both of my '95 fords.. A windstar and an explorer.in both of the cars the abs loses the ability to work properly. At all brake applications to very, very quickly alternates braking b/w wheels essentially it interferes with the braking of the car..remedy is to disconnect the abs. Ford disavowed any knowledge of a pervasive problem..
Tensioner belt was going into it's frame holder.while opening the hood and truck running serpentine belt might have break have been cut apart and injuring the person looking for the problem. 3-other explorer had the same problem while i was with the mechanic.
Clear coat is pealing on hood and over back hatch, transmission problems and headlight problems the headlight will not work on dim i have taken it to the shop and they can not find anything wrong with it.the sensor keeps going out on the transmission.
Items subject of 12/01/00 recall have also failed on my vehicle (both original parts). No safety defect listed in summary.
Center console caught fire.
Since 1997, vehicle has had problems with the check engine light.response from ford was that due to the large number of sensors that activate the light, it would be impossible to tell what was setting it off.then told ford to run pcm diagnostic test to obtain codes, didn;tknow what i was talking about.finally got them to do it, and it came up with faulty o2 sensor.replaced sensor, and problem persisted.went back, ran test, came back with same results.ford has been no help, contacted ford, said not safety related, therefore not their problem.will never buy a ford again.
No summary.dt
Environmental control system,1995 ford explorer -air flow blend door failure caused windshield to completely fog obscuring view forcing emergency pull over and stop on interstate.other drivers were forced to take evasive actions to avoid collision. *nlm
As i drive the explorer on the highway or at any speeds for longer periods of time(200+ miles), engine checklight comes on, and the horsepower is affected.gas mileage decreases to about 8 mpg, and this lasts for as long as the vehicle is driven. I have had the transmission replaced, and i have changed the spark plugs, the spark plug wires, the mass air-flow sensor, the fuel filters and the alternator. The problem is still occurring though. I would like to get the problem fixed so as to feel safe in this vehicle.
I got in my car a battery less than 2 weeks old was almost dead nothing was plugged in or on i drove got on the freeway about 20 min on freeway car stops won't move makes rev noiseeventually starts long enough to stop again at bottom of freeway exit starts again get in into gas station i sit in gas station for about 12 hours add 5 quarts of transmission fluid eventually car will let me drive about two blocks but come to find out i was driving well on fire race to get my dog and i out car catches completely on fire fire man says it electric under hood no previous problems other than the battery and the od off light coming on and off i had the car about a month police report number1702207 oakland ca police department
Purchased vehicle from private seller. I asked the seller why the o/d light off was flashing on the dash. He said he had no experience with engines and he didn't know what it was for. The next day, i was checking all fluids and levels. Anyway, i look in the transmission filling area and noticed the level was waaayyy past full (above crossbar area); i see that there is only milky-pink like substance in it.from all the research i have done already, i think the pink substance is a mixture of transmission fluid and anti-freeze. I have not had a chance (or the money) to know exactly what is wrong with it, but i do know that anti-freeze is not supposed to be in the transmission fluid area(s). My guess is that the problem was caused by an internal failure in the radiator cooling line.i believe that ford should recall these transmissions because they know it is a major problem. Please, is there anyone that has already started a class-action lawsuit on ford because of this matter? knowing that they are selling (or sold) a defective product to hundreds of thousands of customers.this has to be a manufacturer issue! the consumer should not be responsible for this issue.
While driving 65 mph vehicle suddenly accelerated to extremely high rpms withoutwarning.the consumer had to press the brake pedal with both feet to get the vehicle to slow down.
Turn on the cruiser control couldn't get it off the throttle was stuck .tt consumer stated the cruise control system would not turn off when applying the brakes and manually pulling the cruise control button off, consumer had to turn off the engine and coast to the side of the road, consumer stated the accelerator throtle was stuck.
Vehicle shaking with unwanted acceleration resulting in vehicle collision due to lack of control.
1995 ford explorer with acceleration problems.customer states that her vehicle accelerated without warning. The consumer stated even having 2 feet on the brake didn't stop the vehicle from accelerating. The vehicle eventually slowed down as if nothing ever happened. The consumer was informed there was no recall for her vehicle.updated 09/17/07.
Cruise control failed to disengage, vehicle went to 90 mph.tt
1). Gas pedal sticks.2). Puffs of smoke come from steering column in the area of the emergency light button.3). Cruise control shuts off.
Throttle binds on initial take off causing abrubt accelleration.due to throttle body valve sticking.newsgroupautos.makers.ford.explorer has confirmed numerous similar complaints.
As i drive the explorer on the highway or at any speeds for longer periods of time(200+ miles), engine checklight comes on, and the horsepower is affected.gas mileage decreases to about 8 mpg, and this lasts for as long as the vehicle is driven. I have had the transmission replaced, and i have changed the spark plugs, the spark plug wires, the mass air-flow sensor, the fuel filters and the alternator. The problem is still occurring though. I would like to get the problem fixed so as to feel safe in this vehicle.
I was driving my car when it began to down shift around 35mph. Eventually, after adding more gas, it kicked into gear. My vehicle is an automatic. Once it down shifts, the od light begins flashing on and off. It has now been doing this consistently. The drive is not a smooth drive and when i am going approximately 50-60mph or more, the car begins to shake.
The vehicle doesn't shift since its missing the transmission wiring harness o/d sensor cant locate a replacement part the check engine light goes on all the time it uses a lot of antifreeze speed control don't work fuel pump keeps going out.
Whle driving down a major highway vehicle suddenl accelerated at approximately 80 mph. Driver hadfoot on the brakes, but the vehiclewould not slow down. Had to get to road side and cut vehicle off.
While merging into rush hour traffic, the throttle stuck at 3000 rpm.when the brakes were applied, it was not enough to slow the car.after 1 mile, the accelerator was finally freed which allowed me to finally regain control of the vehicle.ford says this item is not covered under any existing recalls.
Sudden acceleration.
Upon accelerating the throttle sticks, causing vehicle to increase in speed.*nlm
While traveling with cruise control on and trying to exit,tried to releasecruise control, butvehicle accelerated on its own,resulting in a multi vehicle collision/wrecksimilar to recall 95v052000.
Firestone 7515 garners ferry rd, cola sc 29209 did following repairs:05/22/00 alternator, 05/01/00 both rear calipers & drums, 02/15/00eet/eec sensors, including temp sending unit, egr valve, coolant temp sensor08/07/99 front driver side lower control arm, ball jt, alternatorand horn .i purchased new tires 09/15/00.i removed goodyear tires pulliam put on my truck 08/27/98.
Consumer states was driving with cruise control engaged.attempted to pass another car when vehicle accelerated suddenly.consumer put car in neutral and coasted to side of highway.attempted to restart vehicle and engine revved up to 6000 rpms.on 10/12/02 while driving with cruise control engaged car accelerted w/o warning again.this time consumer lost control of vehicle and crashed sustaining injuries. Ts
Vehicle had sudden acceleration with several different sequences during and after the failure.occured more than 1 time.tt
While drivng the vehicle suddenly went into open throttle position, rpms unknown, shut the engine off, waited a few seconds,turned the ignitionon again and the accelerator was still in open throttle position.
Auto began to accelerate all of a sudden w/o consumer applying any gas- abs brakes failed so consumer had no brakes.tt
Cruise cotnrol failed.
Since i've purchased this vehicle, the cruise control has never worked.
Vehicle accelerates, mostly at speeds of 50-55 mph, consumer applies brake, but engine keeps revving. Consumer then uses emergency brake to slow vehicle down. Then, puts vehicle in park. This has happened 4 times,twice to dealer, cannot find cause.
Turn on the cruiser control couldn't get it off the throttle was stuck .tt
This is a complaint about ford's recall process. I recently received a safety recall notice regarding a fire hazard. I have not owned my 1995 explorer for at least five years. When i called the number listed in the recall notice i got a department at ford - the man said they contract out their recalls to a third party and that he could not help me, nor could he give me their number. He said the company gets owner information by using the dmv. If they had done that they would know i have not owned this vehicle in many years.this recall notice was about a fire hazard and obviously will not get to the person who may now own the vehicle, so it isn't a very effective recall. The third party company who is doing this for ford is not doing a very good job on something as critical as a safety recall.
Upon pressing accelerator pedal and while accelerating onto hwy. Experienced throttle sticking,stayed in wide open position, causing excessive engine speed and power, had to pull up pedal with hand to decelerate on two occasions,has been fixed.
I was driving a 95 ford explorer south bound on us 95 at approximately 70 mph, when the vehicle began accelerating on it's own.when i took my foot off the accelerator the vehicle kept accelerating on it's own even with the cruise control off and my foot off the accelerator pedal.i then tried to apply the brakes but since the vehicle was accelerating the explorer just shook. I also double checked the cruise control and it was in fact off and tried to pump the gas to see if the pedal was stuck but neither worked.when the vehicle reached approximately 85 mph i attempted to shift into neutral when the vehicle skidded out of control.the skid mark was about 350 feet long and then the explorer left the road and rolled a few times until it came to a stop on the driver's side with the engine still roaring.the engine only stopped when passenger turned off the ignition key since the driver was unconscious.
Throttle linkage sticks. *sd
Vehicle experiences intermittent sudden acceleration.
1st incident:dec.12th 1998.concern: speed jumps on highway and surges only when speed control is on.cause: speedometer assembly binding.correction: replace speedometer assembly.cost to me $309.252nd incident:jan.5th 1999.concern: same as 1st incident.speed jumps on highway and surges only when speed control on. Cause: 14401 loom, sensor & assembly shorted.correction: repair loom 14401 speed control diag. R&r sensor & assembly.cost to me: $308.87.3rd incident:traveling on highway with speed control set at 70mph.explorer speed slowly increases to 80 on its own.i look at the speedometer, realize this and tap the brake.the explorer is still going 80mph or higher.i press the off button to the speed control but it will not disengage.i cannot stop the suv.i do not panick but i'm scared as i put on the emergency lights,press with all my might on the brakes and within a few minutes, get the explorer off the road to the shoulder.i put the suv in park, jump out of the car, look both ways, cross the highway, wave my arms for help and watch as my suv is parked with the engine stuck and running at 80mph or more.some good samaritans stop and i explain what happened.one of them approaches the explorer with caution and turns the ignition off and brings me my keys.they look at my manual and unhook the speed control box under the hood.i drove home with the emergency lights on (about 8 miles) going about 50mph with no problems then parked it.if another car had been near me when the explorer went out of my control, i could have hit them and there would have been injuries or possible loss of life at 80mph. Thank you.
When traveling with cruise control engaged ,and upon depressing the accelerator pedal, there was continuous acceleration. Also,while attempting to press the speed control button off, button would not disengage, causing continuous acceleration. Consumer has contacted the dealer. Please provide any further details.
Since purchase of vehicle in 1998 following components had to be replaced: transmission/fuel pump/ all 4 tires blew and not on recall/ cruise control/radio quit, and no longer able to buckle drivers seat belt.*et
I took my 95 explorer in for a recall (09s09) for a speed control deactivation switch which may pose a risk of fire if it leaked. When i got my veh. Back i looked under the hood to check their work. (i am a mechanic my self by occupation) they had replaced the pigtail to the switch but not the switch itself.when i talked to the service manager about it he stated that the pigtail was the fire hazardand they only relocated the switch if it was leaking at the time of the recall. The letter talked about the switch and not a pigtail leaking brake fluid.the switch is mounted on the master cly.above the exhaust manifold area.was your recall intent to have ford replace the pigtail and switch or the pigtail and the switch but only if the switch was leaking. I will be waiting your reply thank you for your time.
Service brakes, hydraulicdetails: i took my 95 explorer in for a recall (09s09) for a speed control deactivation switch which may pose a risk of fire if it leaked. When i got my veh. Back i looked under the hood to check their work. (i am a mechanic my self by occupation) they had replaced the pigtail to the switch but not the switch itself. The letter talked about the switch and not a pigtail leaking brake fluid. The switch is mounted on the master cly.above the exhaust manifold area. The recall intent was to have ford replace the pigtail and switch or the switch but only if the switch was leaking. The service manager would not give me any explanation. Is ford changing the wrong part. I am not sure how the pig tail will stop the brake fluid from leaking.
Vehicle experienced sudden acceleration.
The speed control increases on its own while in motion.the speedometer assembly has been replaced but to no avail.the speed increases and consumer cannot control it, consumer has to put all her weight on the brakes.if consumer lets off the brakes the vehicle jumps forward.the engine races even when consumer is able to put vehicle in park.*jg
While driving at any speed the gas pedal is working intermittently, and when driving the vehicle, it is hard to depress.
While driving vehicle at speed of 55 mph, accelerator pedal stuck while passing.tt
As consumer put vehicle in reverse with foot on brake, engine revved and vehicle surged backward and hit another vehicle. $ amount of damage unknown.
While driving onhighway at 60-65 mphcruise control engaged in whichvehicle suddenly accelerated at speed as high as 90 mph without prior warning, foot was depressed on brake pedal, and vehicle continued to accelerate, brakes failed to respond.in order to stopvehicleit was placed in neutral and then turned completely off. Consumer has contacteddealer. No determination has been made at this time.please provide any further details.
Vehicle went into open throttle position, to stop vehicle applied brakes steering direction of skid to stop the vehicle.tt
Cruise control speed servo failed. *dh
Tl-the driver owned a 1995 ford explorer.the vehicle was parked and shut off for approximately 30 minutes when the driver heard a loud bang and noticed the vehicle was on fire.the police and fire department appeared on the scene to extinguish the fire.no injuries were reported.the vehicle was destroyed but it was not removed from the location.the manufacturer was notified and he was informed his vehicle was included in the recall associated with nhtsa campaign id number 09v399000, vehicle speed control.the vehicle was not repaired.the failure and current mileages were unknown.sm.
My ford explorer cruise control switch in my engine started on fire and luckily i was at the dealer when it happened it was there being fixed because it kept blowing a fuse when the fuse was fixed the cruise control switch started on fire. It looks to me this is a common problem on fords. I have a 1995 ford explorer.i would like to report this because if i did not have know what was wrong i could have been driving the car and burned up. All i want our the new cruise control wire and switch and have it installed at the dealer for free.http://www.usautoinjurylaw.com/cases/fires/ford-explorer.htmhttp://www.switchfires.com/recall.htmhttp://www.washingtonpost.com/wp-dyn/content/article/2007/08/03/ar2007080301845.htmlmy car is not in the least but it should be.
Transmission caught on fire. Consumer stated that when the car is in drive it goes intoneutral and engine revs.
While driving on highway at speed 60 mph the vehicle suddenly accelerated to a speed of 95 mph, the consumer stopped vehicle by putting into neutral.
Dt*: the contact stated while idling in the driveway for five minutes, the vehicle caught on fire.the fire department was contacted and extinguished the fire.the fire department determined the master cylinder switch on the front driver side started the fire.the dealer was not alerted.
The contact owns a 1995 ford explorer. While driving approximately 50 mph, the contact noticed an increase in engine rpms. The vehicle suddenly accelerated abnormally. The contact was able to stop the vehicle by depressing the brakes and the vehicle was towed to the dealer. The technician inspected the vehicle and found that the throttle pedal was sticking to the hood release cable. The technicians repositioned the cable.the approximate failure mileage was 150,000. Updated 01/04/12the consumer stated the engine rpm red lined two or three times, before he regained control of the vehicle, by downshifting and turning off the ignition. He dealer found the throttle pedal sticking on the hood release cable.updated 01/09/12
When proceeding through a light while turning, the truck accelerated.as the driver applied the brakes the truck slowly rotated blocking the second lane.inadvertently, the driver shift gears into reverse then neutral which brought truck back to natural idle.truck diagnosed "air idle control valve" stuck in open position and now needs transmission replaced.please describe details.since the air idle control valve was replaced, the vehicle experienced sudden acceleration.the consumer was concerned about the speed control cables that were recalled on the 1999 explorers. *scc
Accelerator pedal and mounting bracket broke off of the firewall under the dash board and stuck in the accelerated position causing excessive speed and lost of control of the vehicle.closer inspection of the metal bracket that holds the accelerator rod and pedal broke off the firewall.weld broke, the bracket in question has holes drilled into it at the top and bottom a diameter of about 7/16" but bolts and nuts are missing.owner resecured this bracket by drilling thru the firewall and secured the same with two bolts, two nuts and two washer. This problem also affected my 1996 explorer.
Consumer states while coming into long driveway the accelerator pedal got stuck attempted to brake with pedal and emergency brake. Drove into brick wall.neither one of the air bags deflacted.dealer notified.
Accelerator got stuck, causing the vehicle toaccelerate. Driver could not stop vehicle, not even with thebrakes. Vehicle ended up hitting another automobile in order to stop.
Consumer had noticed that whendriving and upon depressing the accelartor pedaland releasing footfrom pedal,thevehicle continues toaccelerate as if force was still being applied to the pedal,causing the consumer to havehave some near mishaps. Consumeralso contacted the dealer on a number of occasions due to the above listed problem.
My 1995 ford explorer has the accelerator pedel sticking at high rpm which causes the vehicle to lock wide open throttle resulting in the vehicle speeding out of control.the vehicle cannot be stopped even by standing on the brake pedel with both feet.this has happened several times.throttle can be unstuck only by stomping on throttle several times.
Accelerator pedal spot welds, which attach the pedal to the floor of the vehicle, came loose.
Accelerator is sticking. Has this been reported before to this model?
While traveling at highway speed of 50 mphaccelerator pedal broke completely off from weld, and left vehicle without power. Dealer notified, and repairs were made at consumer's cost.
Accelerator pedal sticks.
While driving and applyinggas pedal, gas pedal gets stuck, causing vehicle to accelerate and keep going until the consumer is able to pull gas pedal up withher foot in order to get vehicle to slow down. *ml
While driving on i-95 in route from nc to fl the accelerator stuck. Vehicle was very difficult to control while braking and trying to get over to shoulder. Incident was reported to ford via their web site on 1/10/03, case id 681115, no response to date.
Consumer stated the accelerator pedal jammed between the center mount and carpeted floor while driving, the pedal including the steel arm and mounting bracket failed, which became separated from the firewall, the accelerator pedal mounting bracket that holds the entire pedal and related arm cable broke, closer examination revealed that the accelerator pedal bracket was tack welded to the interior of the firewall under the drivers side dashboard, the weld holding bracket failed causing the pedal to get stuck.
Gas pedal sticks- repld at 30,000 miles under warranty with upgraded version per dealer. But it is now sticking again. Dealer says manufacturer will not cover under warranty at this time.very hazardous when attempting to accelerate.an accident waiting to happen.
Consumer stated the accelerator pedal jammed between the center mount and carpeted floor while driving, the pedal including the steel arm and mounting bracket failed, which became separated from the firewall, the accelerator pedal mounting bracket that holds the entire pedal and related arm cable broke, closer examination revealed that the accelerator pedal bracket was tack welded to the interior of the firewall under the drivers side dashboard, the weld holding bracket failed causing the pedal to get stuck.
I presses the throtle very hard to accelerate and the pedal frozefull throtleit tool about 50 yards to stop the engine remained full throtleit finally changed after i switched to park gear,but only after the engine raced higher for about 5 seconds.
Vehicle experienced sudden acceleration while driving at 70 mph. When this occurred the accelerator pedal went to the floor, and didn't go back up until the truck was stopped and turned off. Cruise control wasn't engaged at the time of the incident.the emergency brake was engaged and service brakes were depressed to stop or slow down the vehicle.dealership performed several tests, including a diagnostic test, but no problem was found. Vehicle is currently at the dealership.
While drivingall of asudden gas pedal stuck all the way to the floor and didn't release.
While driving stepped ongas pedal andpedal just came off. Then, stopped vehicle.vehicle had to be towed, and repair edat a ford dealer. Could not explain what wascause of this problem.
While driving, gas pedal completely collapsed; factory weld came off; lost all vehicle power; managed to drift to side of road; speed 45 mph.tt
When driving at 40 mph and taking foot off accelerator pedal to slowdownvehicle will stall. Consumer must shift into neutral to restart vehicle.
Accelerator sticks to the floor.
Dt*: the contact stated while driving 70 mph on the highway, the accelerator pedal bracket suddenly fractured and the pedal went all the way to the floor.the vehicle started slowing down, the engine was still idling but the throttle did not have impact on the rpm.there were no warning signals prior to the incident.updated 11/3/2006 - the brackets spot welds (3) broke causing the bracket, with the pedal still attached, to just dangle by the accelerator cable. The consumer repaired the vehicle by drilling 2 holes in the bracket and attaching the bracket to the firewall with bolts.
While putting car in reverse, car took off backwards when consumer took foot offthe brakes without pushing on the accelerator. Consumer hit a tree, thenput car in drive with foot still on the brake, and tires started spinning. Furthermore, gas pedal was stuck like it was in cruise control, and car took off into a 3 foot retainer wall and went over it. Consumr was wearing a safety belt.
While driving and trying to change lanes, pressed onthe accelerator and itstuck dueto abroke weld.this caused vehicle took off.consumer saiddriver had to press the gas pedal again to get pedal unstuck.
Gas pedal assembly detached from vehicle at fulcrum during normal operation of vehicle.
Bracket that holds accelerator in place has sheared off.dealer has been contacted.
While driving applied pressure to the accelerator pedal to accelerate slightly in order to pass another vehicle. In both instances, the accelrator pedal went all the way to the floorboard without moving the feet whatsoever,and the vehicle accelerated. Placed vehicle in neutral to stop it. Dealer replaced throttle cable.
While driving about 35 mph,trying to stop, the accelerator sped up, causing the vehicle to collide into a tree .dealerhas been contacted.
I have a 1995 ford explorer the windows work sometimes you mit drive a block than thay don'tand the 4/4 will the same thing . My son has 1995 explorer it will do the same thing is there a recall if not ther shough be thank you .
I have experienced an under the hood fire on my 1995 ford explorer which i believe was caused by a faulty speed control deactivation switch.my vehicle had begun to exhibit symptoms which have been described in relation to recall campaign number 05v388000.specifically, the cruise control had stopped functioning, brake fluid was leaking around the switch and my vehicle had started blowing fuses.on october 29th my fiance drove the vehicle to work.shortly after having arrived at work, someone interrupted a meeting she was having with her supervisor to inform her that her vehicle was on fire.the fire was quickly extinguished and the vehicle was not a total loss.in fact, the damage looks relatively minor to me.however the local ford dealership has given me an estimate for repairs in the amount of $12860.02.i have researched and determined that the switch for my explorer is the exact same switch as is used on the 1995 ford f-150, which is the subject of a recall for this very issue.the part number in question for the explorer is f3tz9f924bb.the part number for the f-150 is f3tz9f924b.a parts sales person at the ford dealership has informed me that these parts are identical and has faxed me information to prove this.i also have very good photographs of the damage, as well as the vehicle.the vehicle has not been touched since the fire other than to be towed to the dealership.i believe the estimate for repairs is based on a visual inspection.the fire department was called, so there may be an official report available.
Consumer's concern over the handling by ford motor companies of the cruise control deactivation switch recall.*mrone nov 11, 2003 the consumer took the vehicle to the dealer because the brake light illuminated, brake fluid was leaking and the cruise control no longer functioned.the dealer quoted the consumer $5000 to fix the vehicle.the consumer declined the repair, purchased the part himself and replaced it himself.the consumer recently heard about the recall and contacted the manufacturer to see if he could recover the money he spent to replace the faulty parts.the manufacturer indicated that the consumer's vehicle was not included in the recall.the consumer's vehicle also experienced stall during acceleration, excessive tire wear, pulling to the right and transmission failure.
We own a 1995 ford explorer xlt that has a faulty cruise control switch. Ford will not fix the switch, but has recalled other auto models to fix the same problem.
Dt: 1995 ford explorer - master brake cylinder caught on fire. Incident occurred on september 8, 2005. While in the drive through at a fast food restaurant started smelling smoke, smelt like plastic. Whenthe consumer lifted the hood it was on fire.
The cruise control failed to work when trying to set the speed.dealership was notified, but did not resolve the problem.
While putting car in reverse, car took off backwards when consumer took foot offthe brakes without pushing on the accelerator. Consumer hit a tree, thenput car in drive with foot still on the brake, and tires started spinning. Furthermore, gas pedal was stuck like it was in cruise control, and car took off into a 3 foot retainer wall and went over it. Consumr was wearing a safety belt.
Ac stay on, cannot defrost.i suspect blend door, according to internet forums with the same problem
While driving turned on the defroster, windows got fogged up, driver unable to see, driver lost control of vehicle. Ran into ditch. Vehicle being towed to dealer. Insurance adjustor looked at vehicle.
Problem with heater/a.c. System. *dh
Water got sucked into the air intake, through the air filter, and into the engine, resulting in hydrostatic lock-up and total engine failure.
Heater was blowing out cool air when used. Vehicle had been taken to the dealer, who informed consumer that the heat plenum malfunctioned and needed to be replaced.
Rear window in the suv exploded because of the heat. The dealer is aware of the problem. The window is being replaced.
Rear window exploded while vehicle was parked, reason unknown. Nothing has touched the window when this occurred. .dealer/manufacturer notified and informed consumer that repairs would only be done at consumer's cost.
No summary listed for above vehicle.
Rearview mirror creates visual obstruction. *aw
Rearview mirror is located too low, causing a blind spot located in driver's direct line of sight, also bumper rusted.
Location of rear view mirror interferes with forward visibility.
Rear view mirror became unglued.
Rear view mirror came off.
Power sunroof failed. *dh
Driver's side window imploded while driving on the freeway covering the driver and interior with glass.
Blend door breaks -windshield frosts in cold wheater
Windshield defect causing poor visibility in line of vision, replacement of windshield & wiper arm did not correct the problem.
Driver window has fallen out of the door panel, causing the window to become inoperable.please give any further details.
Defect in the windshield causing a line in the vision, replacing windshield and wiper arm.
Windshield washer will not spray fluid on the windshield unless it's pushed hard repeatedly, also the windshield wipers come on for no apparent reason.
Washer function only intermittently. Wipers often stop or work at arbitrary, intermittent speeds. Dealer said they fixed it but it stopped working shortly thereafter. Didn't have the energy to argue with them. This problem has been going onn since about a year after car was purchased. I saw a news article aboput the problem and thought i would contribute another report. Thanks!
Windshield defect causing poor visibility in line of vision, replacement of windshield & wiper arm did not correct the problem.
I was driving my car when it began to down shift around 35mph. Eventually, after adding more gas, it kicked into gear. My vehicle is an automatic. Once it down shifts, the od light begins flashing on and off. It has now been doing this consistently. The drive is not a smooth drive and when i am going approximately 50-60mph or more, the car begins to shake.
Passenger rear tire came off of vehicle.*mr the consumer stated the vehicle had been serviced the day before, all of the wheels were removed because the brakes had to be serviced and it was possible the lug nuts were not properly re-torqued.
While driving on highway travelling about 35mphall ofasuddenrear right wheel started to wobble.noticed that the 3 out 5 wheel studs had broken off.contacted dealer. Repaired vehicle at no cost.
Aluminum wheels cause tires to go flat. *dsh
Read more
