Enter VIN number
Get the most accurate report for the vehicle. Basic information is FREE
Use this form now and GET 20% DISCOUNT for CarVertical reports!




We found the following complaints for DODGE GRAND CARAVAN (1991)

Read complaints for DODGE GRAND CARAVAN (1991)


Air bag deployedwhile crossing railroad tracks doing 15-20 mph. Can nhtsa help or provide additional information in this matter.

Abs brake alarm and dual pressure switch was part of the recall but the pressure switch wasn't replaced.*phthere was also a problem with the vehicle not being able to start up due to a dead battery. *mr

While driving the van cut off.itcoasted to the side of the street, and when stopped driver smelled smoke. Saw flames coming from underhood.rescued the children from the vehicle.phoned 911, and fire department and police came.the vehicle was towed to s & w towing lot, and there has been no informaion obtainedas to the cause of the fire.

Vehile parked in drivewayvehicle caught fire. All the switches & control modules had melted. The wiring harness was also melted. Was informed that it was an electrical short that caused the fire. The fuse had failed to blow.

Consumer was drivingvehicle out of driveway an noticed black smoke coming fromsteering column. Dealership is aware ofproblem.

Vehicle parked in garage, house smoke alarms went off, owners discovered vehicle on fire, originating underhood.

Vehicle experienced intermittent failure of the body control module prior to replacment, resulting in multiple component failures. Mjs

Andy lewis dodge did not repair anti lock brakes on recalls they were hostile to me and my van was operable when left there. When i picked it up i had to have a wrecker take it home.the battery was dead and the antilock light continued to stay on. They never repaired the brake problem with the recalls. They are leaking now.

While driving engine stalled.then, consumer found outthat camshaft was broken, and engine had to be replaced.

Belt tension pulley failed.

Without prior warning, there is a loss of power, and their is a fuel leakage from the fuel rails.also, there is some type of knocking noise coming from the vehicle,and enginecylinder head had to be replaced.

The mounting bolt/stud for the dynamic tensioner broke, causing loss of serpentine belt driven accessories including the power steering pump, alternator, and water pump.the failed tensioner was a dealer-installed warranty replacement of an oem part; the oem part was replaced due to excessive belt noise on 5/25/93 with 25,915 miles on the odometer.

Vehicle parked in garage, house smoke alarms went off, owners discovered vehicle on fire, originating underhood.

While driving vehicle would lose all power; there's no steering; no braking; engine stalls; transmission does not work; would happen at various speeds; sometimes not starting at all.

Part failure caused 4 people to be marooned on interstate hwy5 at night.

Andy lewis dodge did not repair anti lock brakes on recalls they were hostile to me and my van was operable when left there. When i picked it up i had to have a wrecker take it home.the battery was dead and the antilock light continued to stay on. They never repaired the brake problem with the recalls. They are leaking now.

Muffler replaced three times.

Electrical shortage in driving module caused fire in wiring loom.

Headlight lenses areyellowing and causing poor visibility. Dealer has been notified.manufactures stated the problem is due to the vehicle age and mileage.

Headlight coversare turning yellow. Could not see in dark while driving. Was causing poor visibility for the driver. Took to dealership & the covers were replaced with brighter ones.

Front headlamp plastic lenses of this model grow opaque with time and very little light is able to pass through making it very dangerous at night.the model includes years 1991 through 1995 and possibly the model previous.the lack of light at night is a road hazard both to the driver and oncoming traffic.there is possibly a defect in the type of plastic used or a reaction with the heat of the lamps with the plastic.i have never seen an clear front lense in these models which include the dodge grand caravan, caravan, plymouth grand voyager and voyager.

The head light covers became discolored, which made it difficult to see at night.

Fuel railleaks gas into engine compartment.

I contacted nhtsa over a month ago (odi# 736341), but have heard nothing back.are you hearing me?this problem presents a high degree of danger for a fire. No safety defect listed in summary.

Fuel rail developed a leak at pivot joint between one side portion of rail and center connecting section.nlm

Fuel rail developed leak. Drips gasoline on hot engine parts. Other makes/models have been recalled according to my understanding. Parts are even on back order by chrysler until feb 14th at least. The parts department tells me these have been "trickling in" i guess for other makes/models/years?. But not for our particular vehicle. This seems to be a serious safety concern to me and will cost in the neighborhood of 350.00 for me to get this repaired.

Dealer determined vehicle is leaking fuel onfuel rail at o rings.

Fuel injection system was leaking gas on top of engine.dealer replaced defective injectors twice,and problem has not reoccurred..et.

Fuel rail severely leaks gas at non-servicable o-rings, causing a serious fire danger, when engine and fuel lines are cold.

Without prior warning, there is a loss of power, and their is a fuel leakage from the fuel rails.also, there is some type of knocking noise coming from the vehicle,and enginecylinder head had to be replaced.

Consumer stated upon starting vehicle gas fumes filled the inside compartment, then gradually dissipated.the fuel rail was replaced. *sc

While driving daughter to daycare vehicle acted like it was running out of gas. Started shaking very badly.pulled over,waited a little bit, drove, and started the same problem again.contacted dealer, and was told the fuel injection needed to be cleaned.had that done by a local mechanic.problem went away for about a week.found out by the mechanic that the fuel rail had a leak which wasdripping onto the engine, which could cause a fire.tried to contact manufacturer for the fuel rail, and was told that it is on back order for up to 6 months.

I would like to know if my vehicle, a 1991 dodge caravan with 3.3l v-6 engine is included in the leaking fuel recall (i.e. Fuel rail seals)here is the recall i researched for your reference:nhtsa campaign id number: 00v268000fuel: fuel injection systemmanufacturer: daimlerchrysler corporationmfg. Campaign #: 895 year: 1998make: chrysler truckmodel: town and countrypotential number of units affected: 1163000manufactured from: feb 1995 to: sep 1999 year of recall: '00type of report: vehiclesummary: vehicle description: mini vans built with 3.3l and 3.8l engines. The fuel injection delivery system can leak fuel from some of the sealing o-rings or from hair line cracks in the thermoset fuel injection rail. Fuel leakage in the presence of an ignition source can result in a fire. Dealers will install a seal on the vehicle fuel rails to prevent external leakage of fuel from the fuel rail crossover tube, should the existing o-rings continue to degrade. Daimlerchrysler has not yet provided nhtsa with an owner notification schedule. However, if a vehicle is leaking fuel from the o-rings or from a cracked fuel line, the vehicle should be taken into a dealer to have this repaired as soon as possible. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact daimlerchrysler at 1-800-992-1997. Also contact the national highway traffic safety administration's auto safety hotline at 1-888-dash-2-dot (1-888-327-4236).

I was on my way home with my four kids when i noticed a strongsmell of gas. When my husband got home i had him look at it to find out it was leaking gas from the fuel rail so bad that there was standing gas on the valve cover leaking into where my spark plugs are. I contacted the place i am buying it from and they refuse to fix it, unless i pay for it. Is there any recall in this problem?i see there has been many complaints same as mine.

Separation of fuel rails connecting u tube cuasing fuel leak onto spark plugs.gas odor in van led to discovery of problem before tragic consequences.repair shop informed us that they are seeing this problem often.

Heavy gas smell. Mechanic identified o-ring failures on injectors and fuel line.

Vehicle experienced a leak in the fuel rail. Ownercontacted the manufacturer and the dealer, and neither was willing to assist the owner.....

Fuel rail is leaking onto the top of the engine block.consumer has tried unsuccefully to get the replacement part, but it is not available.nlm

The vehicle had no instrument panel readout.the dashboard lights came on, but the consumer was unable to tell how fast she going..

Liftgate bolt broke, causingliftgate to fall down, and may have caused injuries.there is a recall for 1992 grand caravan, recall97v079000, but this vehicle is not included in the recall due to vin although ithas the same problem.please provide further information.

Transmission shifts weirdly.

Around august 4, 2003, my dodge grand caravan suddenly locked in second gear. I have replaced the filter and the transmission fluid. This did not fix the transmission. While asking friends if they knew any to fix the problem before i take it to a shop to be fixed, one of them print me the information about the chrysler ultradrive transmission report that is on your web site. I have got to my local dodge dealer and they said that they have never heard of ultradrive transmission problem or recall. I showed the dealer the information that i printed from the web site. Dodge said that i would need to call chrysler. I have called chrysler customer relations about the ultradrive transmission locked in second gear. I was told that they only have 4 recalls on the van two of the recalls have been complete but to have not. The two recalls that have been done are: liftgate latch pn cfxr6406 and seat belt buckle/anch. Clip. The two recalls that have not been done are: liftgate support washer and a left wiper pivot.i then explained to the chrysler customer relation that the records on they web site only shows back to 1996 per the web site information. They said that any recall would be with the vehicle for life in the system. I also asked if they had any information on the ultradrive transmissions having a problem with the 1989 to 1991 models. The person said that they are unable to look that information up.i then explained that the information is on the center for auto safety web site. The customer relation person said that if the information is not on the chrysler or dodge web sites then the information is not right. Also the relations person said that even if there was a problem with the ultradrive transmission that it is no longer covered under the manufactures warranty anymore.please contact me by e-mail if you have any information that i may use to resolve the problem with the ultradrive transmission.

Andy lewis dodge did not repair anti lock brakes on recalls they were hostile to me and my van was operable when left there. When i picked it up i had to have a wrecker take it home.the battery was dead and the antilock light continued to stay on. They never repaired the brake problem with the recalls. They are leaking now.

Automatic transmission failure.

Vehicle shuts down completely fromtransmission.vehicle will start back up, but will not go faster than 30-40mph. Before whentransmission was changedvehiclewouldn't go faster than 10mph. Dealer kept rebuildingtransmission,and consumer had to pay out of pocket too often to repairtramnsmissionagain.

Transmission slipped twice.

Vehicle isn't going intogear properly.when puttingfoot on gas pedal vehicle jumps forward, and the gears shift. Thenvehicle cuts off without prior warning, andvehicle won't move sometimes.

Replacement transmission was purchased through chrysler and lasted only 29,000 miles before failing in washington d.c. Traffic on mother's day.chrysler will not replace and are non-responsive to my requests to meet on the subject.

1.transmission solenoid body locks transmission in drive/2/1 range.(the transmission cannot be shifted to neutral, reverse or park without a great amount of force.)disconnecting the battery resets the controls and allows the gears to be changed normally for a month or so.2.idle air control motor sticks in the open position, causing the engine to idle at a high rpm (1000 to start with, more if not replaced right away).this makes stopping the vehicle more and more difficult.

Transmission failed.

While driving vehicle would lose all power; there's no steering; no braking; engine stalls; transmission does not work; would happen at various speeds; sometimes not starting at all.

Original transmission was rebuilt by dealership at our expense.later, had to replace the transmission because of the same problem.chrysler would not cover any of the expenses and we have never heard if any recall work was done for transmission problems.

Transmission fails continually after repair.

Brakes got red hot with smoke as the only indication. Pedal stiff at top. No brake warning light and no abs amber warning light. Lost pressure down to 14.5 psi in front driver side tire. Tire too hot to touch. Break break//////// on older transmission failure the fol. Applies. Transmission seized as though it went into park. Van shook violently until neutral selected on gearshift allowing me to coast to stop. Second complete transmission swap out. First was at 90k miles. Still have part that failed. Second failure i was almost hit from behind.

Consumerhas had toreplacetransmission every year for the past four years.

When driving the vehicle jumps into different gears and jerks all the time. Dealer has not seen.

Transmission rebuilt due to difficulty shifting out of first gear.

While driving the center seat/right side seat belt anchorge releases when the belt is being used due to a problem with the spring clip,dealer has not looked at vehicle for this problem.

The center seat/right side seat belt anchorage releases when seat belt is being used.

While driving, the center seat/right side seat belt anchorage releases when belt is in use.

Seat belt anchorage, the middle seat right hand side the floor latch becomes unbuckled,the little clip that hooks comesapart when driving after being attached. Consumer states the clip is not secure.

Safety belt buckle that isattached to floor comes undone, swings in air.

While driving, the center seat, right seat belt anchorage release, when seat belt is in use.

Middle seat belt designed w/movable floormount, allowing belt to occasionally fall off as it was being put on/taken off.

Seat belt unhooks from floor anchor.

Driver's side seat belt will not extend from the panel. Dealer has been notified. Please provide further informaton.

The seat belt hook on the right side in the middle of the vehicledisengages from the metal floor anchor.the spring clip is not broken. Consumer has not taken the vehicle to the dealer.please add further information.

The floor anchor of the rear seat belt failed.

The center seat/right side seat belt anchorage releases when trying to put on belt. Replaced spring clip several times.

Ea-97-005, the vehicle rear middle right side seat belt anchorage comes loose,preventing protection to the occupant if an accident occurs.

Seat belt in middle rear becomes detached due to a faulty spring clip which snaps inside out. Owner is very concerned for his safety.

Ea-97-005, the rear middle seatbelt achorage does not hook on when using the seatbelt.won't protect the occupant if in an accident.

Center seat right/side safety belt anchorage releases frequently when the belt is in use.

The right side seat belt in the second row comes unhooked from the floor anchorage.problem has not been corrected.

Center seat/right side safety belt anchorage releass frequently when the belt is in use.

Seat belt clip comes off of wall or floor.

Seat belt hook/floor anchor on the middle row/right side failed.

Middle seat belt buckle inoperative.

The driver side seat belt wouldn't hold when trying to latch.

Drivers side seatbelt would not unbuckle. Problem area is buckle housing mark press. Consumer was unable to unbuckle the seat belt, after an hour he went to the dealership and they were unable to unbuckle it so they advised him to cut it off, they could not cut it off due to liability reasons.

Driver's side seatbelt will not stay buckled, inside ofplastic came out with buckle.

Driver's side belt buckle failed tolatch properly. Had to insert latch into buckle on several occasions before it locked properly. Dealer was not contacted.

Consumer went to reach for seatbelt, seatback broke, causing the seat to fall backwards. Seat completly broken, will not stay up.

The contact owns a 1991 dodge grand caravan. While driving at unknown speeds, the brake pedal was depressed, but failed to engage and traveled halfway to the floorboard. The contact stated that the brakes eventfully engaged after the brake pedal was depressed several times. In addition, the anti-lock and brake indicators were illuminated. The vehicle was towed to an independent mechanic, but they were not equipped to service the vehicle. The mechanic referred the contact to another independent mechanic who then referred the contact to a local dealer. The vehicle was towed to glenbrook dodge chrysler jeep (100 w coliseum blvd, fort wayne, in 46805, (260) 579-4713) where it was diagnosed that the anti-lock system failed and the vehicle was in manual mode. The dealer informed the contact that parts were no longer being manufactured. The manufacturer was notified and opened case number: [xxx]. No further assistance was provided. The failure mileage was 66,000. The vin was not available. Information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6).

The contact owns a 1991 dodge grand caravan. The contact stated that there was a failure in which the previous owner had to replace the abs hydraulic control unit. The vin was not included in nhtsa campaign number: 96v099000 (service brakes, hydraulic). The failure recurred and caused the reduced power assist to fail during braking. The vehicle was taken back to the dealer. The dealer kept the vehicle for over two weeks. The manufacturer was notified of the failure and provided no solution other than suggesting the part be replaced a second time by the dealer. The contact was unable to determine if the same part being replaced would prevent the failure or if the failure would recur. The approximate failure mileage was 140,000.

Nhtsa recall:96v099000lifetime coverage...bendix 10 abs brake failure.chrysler corporation denied reimbursement of repairs on 10/20/2020..

Defective abs.

Nhtsa recall #96v099000, referencing abs lifetime warranty.dealer crystal chrysler center, cathedral city, california, (760) 324-4557, has failed to repair the defective abs system of this vehicle under the mandated nhtsa lifetime warranty.dealer has had this vehicle for over six months with the excuse that "diagnosis" is in process.chrysler corporation's "executive referral" customer assistance (586) 274-8177, has failed to assure customer satisfaction.abs anti-lock light remains on, pump and actuator assembly continues to fail and has created a "dead short" in the "fusible links" causingcatastrophic failure in the wiring harnesses.no matter the mileage of this vehicle, i am requesting repairs to the entire abs system under the nhtsa lifetime warranty...please assist.update 9/15/15*cwupdated 11/10/11.

Abs brake alarm and dual pressure switch was part of the recall but the pressure switch wasn't replaced.*phthere was also a problem with the vehicle not being able to start up due to a dead battery. *mr

Andy lewis dodge did not repair anti lock brakes on recalls they were hostile to me and my van was operable when left there. When i picked it up i had to have a wrecker take it home.the battery was dead and the antilock light continued to stay on. They never repaired the brake problem with the recalls. They are leaking now.

Nhtsa recall #96v099000, referencing abs lifetime warranty.dealer crystal chrysler center, cathedral city, california, (760) 324-4557, has failed to repair the defective abs system of this vehicle under the mandated nhtsa lifetime warranty.dealer has had this vehicle for over six months with the excuse that "diagnosis" is in process.chrysler corporation's "executive referral" customer assistance (586) 274-8177, has failed to assure customer satisfaction.abs anti-lock light remains on, pump and actuator assembly continues to fail and has created a "dead short" in the "fusible links" causingcatastrophic failure in the wiring harnesses.no matter the mileage of this vehicle, i am requesting repairs to the entire abs system under the nhtsa lifetime warranty...please assist.update 9/15/15*cwupdated 11/10/11.

While driving,the consumer applied the brakes and a loud humming noise was heard from the front.the driver was able to drive the vehicle to the dealer for inspection.the consumer informed the mechanic a recall notice #(v96099000) regarding the abs hydraulic unit was for this vehicle.the mechanic informed the consumer that the recall was performed in july of 1997 and the remedy was not available for again.please fill in additional information.

While driving abs system went out. Contacted dealership.

The anti-lock braking system failed.nlm

Upon receiving arecall noticeconsumer took the vehicle to service dealerfor repairs of abs brakes.the service dealer told the consumer that he would need to pay for a diagnostic. Consumer statedthere were7 recalls on this particular vehicle. The recall specifically stated thereno charge to the consumer.

Abs/brake light is on for more than 2 minutes, braking condition significantly decreased or vehicle won't stop.

Abs brakes failed prior to recall, recall repairs performed. However electrical parts were not changed since they were not covered under the recall. Owner paid $66.50. 96v-099.

Master cylinder leaking on several occasions due to failure of the abs system prior to recall notice.

While driving approximately 30 mph consumer applied the brakes to come to a stop. When proceeding to pull off vehicle hesitated and wouldnot move. When taken to dealerforservice it was determined to bethe abs not unlocking.

Abs brake failure. Also replaced piston actuator.

While traveling noticed abs indicator light flashed on soon after depressingbrake pedal and vehicle lost all braking power. Please provide further information.

Abslight came on. When brakes were applied, had no brakes. Pedal failed to respond. Felt very hard. Coasted vehicle to side of road. Had vehicle towed to mechanic. Informed a relay/dual function switch had to be replaced. Switch acted as if it was turned off when it was on.

The first repair we were charged with the replacement of the master cycl and the abs piston assy and we were never told it had been recalled, they charged us for 5 pints of brake fluid and all parts totalling $494.51 to complete this job. Since they did not know about the recall. I really doubt they did the job correctly. The next occurrance explains the brake fluid. Then approx 3 months later the brake system completely failed, they said they found a foriegn substance in the brake system, it looked like some type of grease, they said they contacted a area rep and they tested the fluid and found 20% of petrolium in the fluid. They were the only ones that have ever serviced our brake system, now they are denying all responsibility and will not honor the work they did. I talked to other chrysler dealers and they said this job only take 2 pints of brake fluid to complete this type of job. 5 pints is enough to fill the system 1 and a half times. I do not have a technical sheet from chrysler detailing the proced

Abs braking system malfunctioned due to a defective pump relay dual function and a switch pressure acutator, which may resultin extended stopping distance.please provide further information.

Recall repair on the abs system completed, however failed the next month. (96v-099)

Received recall notice on abs brakes,took it to dealer and he said that there was no problem on brakes,send the vehicle home and the brake light still stays on. Took it back and dealer replaced the piston but the brake light is still on.(92v-030).

Antilock brakes failed twice, once causing accident.

Brakes got red hot with smoke as the only indication. Pedal stiff at top. No brake warning light and no abs amber warning light. Lost pressure down to 14.5 psi in front driver side tire. Tire too hot to touch. Break break//////// on older transmission failure the fol. Applies. Transmission seized as though it went into park. Van shook violently until neutral selected on gearshift allowing me to coast to stop. Second complete transmission swap out. First was at 90k miles. Still have part that failed. Second failure i was almost hit from behind.

When applying the brakespedal stiffens and vehicle will not slow down. Owner has to force full body weight on pedal in order to stop vehicle. Dealer has replaced the electrical relay.

Anti lock brakes failed prior to recall notice.

When applying the brakes the vehicle makes a ginding noise and excessive pressure is needed.

Recall 96v099000/ abs brakes.dealer refused to service vehicle due to mileage.

Abs brakes failed prior to/after recall repairs. Also brake warningsystem malfunctioned. (96v-099).

Consumer received a recall noticeon the abs system. At the time the vehicle was o.k. Vehicle is over the extended warranty of 10 years and 100,00 miles. The dealer is notwillingto repair the seatat their expense.

Antilock brakes failed.

Antilock brake warning light illuminated.

Abs brakes failed prior to/after recall repairs. Also brake warningsystem malfunctioned. (96v-099).

Front brake shoe replaced.

Brake pads are corroded around the edges. Winter road chemicals disintegrated brake pads. The dealer has been notified.

The first repair we were charged with the replacement of the master cycl and the abs piston assy and we were never told it had been recalled, they charged us for 5 pints of brake fluid and all parts totalling $494.51 to complete this job. Since they did not know about the recall. I really doubt they did the job correctly. The next occurrance explains the brake fluid. Then approx 3 months later the brake system completely failed, they said they found a foriegn substance in the brake system, it looked like some type of grease, they said they contacted a area rep and they tested the fluid and found 20% of petrolium in the fluid. They were the only ones that have ever serviced our brake system, now they are denying all responsibility and will not honor the work they did. I talked to other chrysler dealers and they said this job only take 2 pints of brake fluid to complete this type of job. 5 pints is enough to fill the system 1 and a half times. I do not have a technical sheet from chrysler detailing the proced

Abs brake failure. Also replaced piston actuator.

While drivingheard a noise inthe steering column . Thentook the vehicleto the dealerand was informed that the steering wheel was broken.

While getting out of the side door of the vehicle the door fell off without inications. Please provide further details.

The sliding side door on my 19991 dodge grand caravan completely fell off while the vehicle was turning a corner. I have noted that tsm's (08-62-93; 08-21-94; and 23-06-93) had been issued describing a defect in the sliding door ajar switch (adjustment).

Side door would be sticking. It fell off the track when closing. Has not been to or notified dealer as of yet.

Retaining bolt failed causing rear door to fall.

Recall 99v-21 is for cracked liftgate bolts, dealer unwilling to check for hairline cracks and stated bolts could only be replaced if broken, consumer not satisfied (not pleased).yh

Retaining bolt failed causing rear door to fall.

Upon entering the driver's side and shutting door, the back window of the hatch shattered.

Hatchback hinge snapped, door would not close.

Recall 99v-21 is for cracked liftgate bolts, dealer unwilling to check for hairline cracks and stated bolts could only be replaced if broken, consumer not satisfied (not pleased).yh

One of the two lifttgate support strut anchors shearded off causing the liftgate to fall, components not repaired under recall due to vin.

While unloading groceries, hatch suddenly slammed shut due to failure (shear) of hatches right strut body anchor. My head was grazed, but am ok.plastic trim by anchor damaged.door is extremely heavy, and will not open without strut assist.a failure of this nature is extremely dangerous - what if the door (500lbs + enertia) fell on us or the kids while unloading groceries, or sitting on gate for tailgate party/drive-in?falling with the speed and force it did would act like a leg/neck/bone crushing guillotine.it is lucky that no one was hurt, but someday, some one will if this weak design is not corrected.i say it is weak because anchor diameter appears to be 1/4" which is ridiculous.3/8" would be minimum diameter for proper design.please do something before someone gets killed.signed - brian d. Lubell

Recall 99v-21 is for cracked liftgate bolts, dealer unwilling to check for hairline cracks and stated bolts could only be replaced if broken, consumer not satisfied (not pleased).yh

The bolt that supports the strut, on the right side of the tailgate , sheared off and caused the gate to fall, hitting owner's head. The problem has not been corrected.

While driving right front axle broke, causing vehicle to stop because wheel will not turn. Had repaired. Axle broke again 3 more times. Also, left front axle has broken. Dealer contacted.

Failure of front left ball joint and axle.ball joint fractured and wheel came off while driving.

While traveling emergency spare tire straps and clamps separated from tire, causing tire to roll onto highway. Replacements made at half cost.*ml

Andy lewis dodge did not repair anti lock brakes on recalls they were hostile to me and my van was operable when left there. When i picked it up i had to have a wrecker take it home.the battery was dead and the antilock light continued to stay on. They never repaired the brake problem with the recalls. They are leaking now.

Vehicle isn't going intogear properly.when puttingfoot on gas pedal vehicle jumps forward, and the gears shift. Thenvehicle cuts off without prior warning, andvehicle won't move sometimes.

1.transmission solenoid body locks transmission in drive/2/1 range.(the transmission cannot be shifted to neutral, reverse or park without a great amount of force.)disconnecting the battery resets the controls and allows the gears to be changed normally for a month or so.2.idle air control motor sticks in the open position, causing the engine to idle at a high rpm (1000 to start with, more if not replaced right away).this makes stopping the vehicle more and more difficult.

The back window of the hatch shattered for no apparent reason.

While driving in the rain, the windshieldwipers failed. Wipers were repaired under recall the first time, then they failed again. Consumer was informed that the defective part was the crank that connected to the wipers and it wasn't covered under the recall. Consumer repaired the part on their own. The slots in the crank flared out which caused it to rock and loosen the nut and fall off.*ph *nlm

Glass wiper won't operate on rear door (stucked up while in operation)creating visual hazards especially when backing up the vehicle during snow/rainy conditions.

Windshield wipers flew off the vehicle, causing poor visibility. The dealer has been notified. Windshield wipers are on back order.

The rear window wiper motor shorted out due to the window washer cleaner leaking into motor. The dealer has been notified. Problem has not been corrected.

Rear window washer motor failed.




Read more




© 2024 All rights reserved