Enter VIN number
Get the most accurate report for the vehicle. Basic information is FREE




We found the following complaints for DODGE DYNASTY (1991)

Read complaints for DODGE DYNASTY (1991)


False deployment of air bag causing consumer to hit curb (minor crash with no damage).

Consumer was traveling about 25mph on highway and without prior warning another vehicle veered into consumer's vehicle.upon impact, airbags did not deploy.dealership was aware of problem.while consumer was trying to turn, the wheel locked and a hit pole and building. During the accident the air bag failed to deploy and the consumer had face and chest injuries.

No deployment of driver's air bag during a frontal crash at 45 mph.

Frontal collision, impact 12:00, speed 35mph, driver side air bag did not deploy, 3 car pile up.

Hit deer on the road drivers side air bag did not deploy.tt

Consumer states that while driving 30 mph the driver's side air bag deployed without impact.

In accident in stop position at 1:30 position drivers airbag deployed and burned bra top body face was burned.tt

Problem with child safety seat.i have the fisher price stay in view.when the lever is pulled to release the seat from the base, one of the mechanisms won't retract allowing you to release the seat.i have informed the manufacturer about this problem.

Vehicle cuts off at random dealer can't seem to find the problem.tt

Entire ignition system separated from steering column. Please describe details.tt

Engine stalls on highway.please give more details.tt

While driving vehicle on the hghway,vehicle just stops. Vehicle has to sit about (3) days before it will start up. This has happened 8 times since may of 96.

Vehicle stalls intermittently while driving, parked, and right after start up; exact cause unknown.tt

Vehicle stalls due to computer failure. Please describe details.tt

Defect in computer causes computer to send "turn off alarm " message to driver; however vehicle is not equipped with alarm system.

Vehicle would constantly shutdown while driving without warning, dealer hasreplaced computer command control module,but problem is still occurring. Consumer stated the starter, fuel injector, fuel pump, fuel filter coil pack, map sensor, and catalytic converter have all been replaced.

The vehicle will start and while driving it will cut off without any warning.dealer replaced the computer chip number of times and vehicle still has the same problem.

Computer designed to allow installation of anti-theft alarm, however this feature causes premature failure of computer.*aw

Car would not start because computer went into security mode (while parked), shutting off fuel supply, although car is not equipped with electronic security system. Computer had to be replaced with an o.e.m. Computer designed to prevent such random occurrances, at my expense of over $500 plus towing charge and inconvenience.

Computer component malfunctioned. *sd

For the third time within a 3 year period my car will start and run for about 2 seconds and turn off, i had it towed and the mechanics would replaced the main computer, or say they did, and charge me a great deal of money. I searched recently on the internet to see if others have had the same problem, and i found that it is a defective part problem found at this site---http://autorepair.about.com/library/a/1f/bl111f.htm i should not have to pay for a defective part which is tied in to an anti theft feature.

Was driving and moved vehicle the steering column burnedthe plastic cover under the electrical ignition, took to dealer and he replaced the ignition switch .

Starter failure. *sd

Transmission,starter and fuel pump were replaced purchase car used .tt

Driving the vehicle and saw smoke and flames coming out of the driver's side door panel.poured water inside door panel, and put flames out.it was stated that it was an electrical fire.

50 amp fuse blew three times. *sd

Computer failed.

Tensioner belt broke while driving, also making a loud noise pe95-012 active.tt

Vehicle leaks oil. *dsh

Vehicle would constantly shutdown while driving without warning, dealer hasreplaced computer command control module,but problem is still occurring. Consumer stated the starter, fuel injector, fuel pump, fuel filter coil pack, map sensor, and catalytic converter have all been replaced.

Steering became hard, resulting in no steering ability, replace belt tensioner and belt.ttdealer replaced serpentine belt and belt tensioner.

Tensioner belt replaced due to noise. *sd

Purchased said vehicle in sept. 2006 used. Was just driving at posted speed limits in a community area of phoenix, when all of a sudden a loud clacking noise started as i pulled up to my designation, so i turned off the motor, lifted the hood and immediately noticed that the tension pulley had nearly completely came off the motor.it did cause the serpintine belt to come off of all the pullies of the motor.i had to have the vehicle towed home, again for the second time since sept. 2006.hen the vehicle was at my home i finished removing the pulley thatwas loose,causing it to bentenough to throw it totally off of its tension purpose.upon removal a bolt was also broken which may have caused the total problem because it was not tightened to torque specs.had to replace both parts attached to this pulley.

Exhaust converter failed.

I smelled a strong order of gas when driving, when i checked under the hood there was a constant dripping fro the fuel rail supplying the fuel injectors...first , it was a small dripping on the front valve cover and after 2-3 months its a strong continuous dripping filling up the valve cover spilling into the manifold area. I have restricted driving my car to 5-7 miles at a time to prevent possible fires.my mechanic called the dealership to see how much they cost and this u-shaped aluminum tubing about14" long ,8" connecting tube where it is leaking from to another piece of aluminum 14" tubing that goes underneath the manifold is $300.00 and $150 to install it. I think it is a factory defect that the manufacturing dealer is gouging almost punishing them for needing the part by charging 3xs what the piping/tubing really should cost. My mechanic and i have been all over the web looking for the same part but all of them say its a discontinued parts and can only be bought by the dealership. What a rip off they know its a factory defect and in high demand but they are not making anymore than that want to make to keep the demand high and to make a big profit on a design mistake in their fuel system design that they sold to the public.they probably knew it was a defective design but pushed it through anyway.

Gas rail sits on top of engine (passenger side), at first i just smelled a whiff of gas occasionally, then the smell became stonger, gas was coming out of the gas rail, at times even squirting a small stream, gas was falling on hot, electrical engine components on top of engine, the running down the side.

The fuel rail that delivers fuel from the gas tank to the fuel injectors failed.

While driving smelt fumes andvehicle stalled out. Contacted dealer.

Fuel rail assembly failed, resulting in gas pouring all over the engine and a pool of gas in the garage.tt

While two months pregnant, my wife noticed a gas odor coming from around the car while she drove to work.she initially assumed it was coming from another vehicle.when i picked her up at work the next day i also noticed the smell of gasoline.when i opened the hood of the car, i noticed a puddle of gas sitting on the top of the engine below the u-shaped fuel track.i didn't drive the car after that discovery for fear that the engine area would ignite.when i contacted a local dealer, they stated that a similar flaw in the fuel track had been recalled on other vehicles for similar reasons.i contacted chrysler only hoping to be reimbursed for the defective part.chrysler's response was that since the vehicle was no longer under warranty, they were not concerned.i'm really only doing this to avoid someone else from being injured by the defective fuel track that leaks and leaves a large puddle of gasoline on top of the engine.

While driving the car stops completely.because of the power module not allowing the gas to get to the engine.please describe.tt

Transmission,starter and fuel pump were replaced purchase car used .tt

Fuel leak,the fuel rail that connects fuel line, has a leak, no parts are available, on national backorder.

While driving gas begin to squirt out of the fuel hose-(a metal piece)

While driving 35mph, noticed odor of gasoline. Pulled vehicle over & parked. Lifted hood & noticd gas had sprayed over engine from 2 spots. Took vehicle to mechanic & was informed fuel rail had a leak. Parts ordered from another state for repairs.

The fuel rail is leaking, causingvehicle to run out of gas at a high rate. Dealer has vehicle now.

The fuel rail leaks like a dripping faucet.this is an item that is on recall for the dodge intrepid.is this the sme part which was recalled on the intrrepid?one dodge dealer parts department said there is a national backorder on this part, and will be at least 2 weeks before one may be available.another said this part almost never goes bad, so they never stock it.it seems that a recalled part should be in sufficient supply for the recall and other customers.is this a common problem with the dynasty too? additionally, the charge for the fuel rail alone is nearly $300.00.is this a fair price?this price does not include installation.dodge recall information line has told me that there are absolutely no recalls on my vehicle.they have my correct name & address, and i have never received a recall notice. Thank you for your assistance.

Vehicle was leaking fuel from fuel injection tube. When consumer started vehicle fuel started pouring out.also,had strong odor of gasoline.contacted dealer, and dealer stated no recalls, and to call nhtsa.

Fuel rail leakages caused fuel to leak all over engine. Spilled fuel could result in an engine compartment fire.

Fuel injection system leaks. *sd

1991 dodge dynasty, 3.3l engine.fuel rail leaking, at crossover tube connection. Fuel leaking down onto vavle cover, which then leaked onto hot exhaust manifold. Minor fire, but thank god i was in my driveway when i smelled the fuel. Opening the hood revealed the small fire that started. The dodge dealer wants 300.00 for the part, and i feel chrysler should pay for this part since it is not a "wear" item, nor is it a moving part, or in a location prone to wear. Had my wife or myself been driving and the fire occured, this could have been a very dangerous situation, and i would have considered a law suit. Any help you can provide me would be great. If you can provide a complaint number to call for chrysler, i will do so. I feel they should at least pay for the part. Vehicle is currently parked, as i cannot locate a used replacement. This is creating a major headache, as we need 2 vehicles, and cannot afford to replace the dynasty at this time, nor can we afford (or justify) 300+ for the repair.thank you.

Leakage of fuel at the fuel rail connections, above the valve covers, which drains onto the manifold and could start a fire. I am told it will cost over $700 to replace the parts which cannot be bought anywhere else.

I own a 1991 dodge dynasty, 3.3 liter. The fuel rail started leaking at the joint on the front, behind the valve cover.

The mechanic stated that he had 6 1991-1993 dodge dynasty 3.3 liter engine, multiport fuel injection system with a defective problem involving the fuel rail in the o rings which shrinks and expands, causing a crack,resulting ina fuel leak, which may start a fire.manufacturer is on national back order for the fuel rail.please provide further information.

Purchased vehicle used oct. 2006. Near mint condition.power everything & everything functions perfect.vehicle emissions perfect.approx. 4 days after final registration was switched, plated, & insured, i hopped onto the freeway, doing about 65 mph. When suddenly in a matter of seconds, i was totally overwhelmed by the smell of gas. I became seriously nauseous and light headed and had to immediately exit the freeway to find somewhere to pull over as fast as i possible could without causing an accident or more serious a fatality.once,i managed to pullover i pulled the hood latch, jumped out to get a breath of fresh air, i popped the hood to try tosee where this gas was coming from. All i could see was gas spaying out all over the place, in massive amounts just like a high pressure hose at a car wash. 1\4 tank leaked out all over the top of the engine & all over the intake manifold of my car.i thanked god, that the engine was not hot enough to ignite the whole car,with me inside.after getting the vehicle towed home, we found out it was the fuel rail feeder that distributes gas to the fuel injectors.the after researching other dodge vehicles i found out there was an undocumented recall for this part,this car year, make and model when it first came out, and that chrysler/dodge continued to install this same part on other years, makes & models &daimler chrysler/ dodge was, very well aware of this.last year they grossed $16.63 million dollars in 2005with $1.5 million in losses & they can't afford to repair this for $700.00 just makes my stomach turn. Now knowing that i could have been killed or could have possibly caused a serious or even fatal injury to someone else, because of daimler chrysler's neglect in admitting this is a defective manufactured part, and them taking full responsibility for this is outrageously unbelievable to say the least.

The fuel rail is leaking from two spots. This was discovered by a mechanic after owner took vehicle to shop for heavy gas fumes. The vehicle is being held at the body shop for repairs. The part is on back order. Please provide any further information.

'o' rings on injectors leaking.

Fuel rail was replaced once in oct. 1991. It developed holes and leaked fuel on the engine. Vehicle has been at repair shop for (2) months because owner could not obtain a fuel rail. Part is on back order.

Fuel rail leaking gas into engine compartment.

Emergency brake pedal arm bent/fell off.

Odometer freezes up when it's cold and does not operate. Please describe details.tt

Speedometer does not work intermittently.tt

While driving at any speed and without warning, thetransmission failed.

Transmission failed.

Transmission,starter and fuel pump were replaced purchase car used .tt

Clamp on transmission hose failed, causing transmission fluid to blow onto engine manifold, resulting in fire.*skd

Transmission (possibly malfunction in computer or solenoid). 2 yrs ago advanced transmissionput in a 604 rebuilt transmission and torque converter. The problem has continued to exist. Most days the transmission shifts fine. Other days the transmission does not shift gears at all. It goes into safety mode and has not gears at all. I never know when it will do this. Also, when i am at a standstill, if i turn off the a.c. The car jumps forward.this has almost caused me to hit other cars in the rear. They have tried putting in other computers and very seldom can get a malfunction readout on the transmission. Seatbelts - the seatbelts do not lock up upon braking nor at any other time. They move forward as far as you move your body forward. They are of no use as a restraint.

Transmission was rebuilt. *sd

Was just driving down road felt like front end was falling out and started jurking.turned around, had to keep pressure on transmission.paid $1600.00 to have transmission replace.

My first transmission failure was during warranty at approx 65,000 miles in 1995.my second transmission failure was in 1997 at 115,000 miles.since i was out of warranty, and did not think chrysler/dodge would replace my transmission i had it rebuilt at my own expense for more than $1700.00.do you think chrysler will reimburse me??.

Automatic transmission will not go into overdrive, vehicle will not travel over 30 mph.

Automatic transmission failure, erratic operation of transmission, please explain.tt

Purchase car new at 79,000 miles the transmission needs to replaced.tt

Automatic transmission will not go into overdrive, vehicle will not travel over 30 mph.

While driving approximately 58 mph on dry pavement, gas pedal was pushed and nothing happened.transmission appeared to be in neutral.consumer pulled over and moved gear shift. After a while,it went into first gear and stayed there, which is the only gearworking now.the three higher gears are not operating at all.dealer has not been notified.no warranty.

Auto-transmission; while driving a computer in transmission failed, resulting in vehicle speed not exceeding 30 mph. Please describe details.

Transmission is slipping, speed drops and then it jerks.tt

Transmission failed.

The transmission caught on fire and the transmisssion was acting up before also. Please describe.tt

Automatic transmission:second gear burns out, will not come out of 1st gear, entirely overheats, no pickup/no acceleration, dealer stripped / rebuilt 2nd gear, replaced all gaskets inside transmission.

The transmission jumping out of gear sometimes it wouldn't go back into gear .tt

While backing vehicle up the reverse went out & then it locked up. The4 cylinders were bad. Had the transmission replaced with another rebuilt transmission in 1994.

Transaxle failure caused vehicle to jolt forward.

Consumer experiencingongoing problem with seat belt not locking and unlocking properly. Daler notified and repaired passenger's side buckle at the cost to the consumer.

Problem with front seat belts latching and unlatching as recall states dealer won't fix because vin is not involved.tt

Seat belts buckles do not clipin well/sometimes come out.

All the seat belt mechanisms are difficult to operate. Please describe details.tt

Both rear set belts have trouble being pulled out. They seem to get stuck and cannot be used. This could result in serious injury or death to rear passengers. I have yet to fix the problem.

Antilock brakes failed.

The abs system in the vehicle failed. In a panic stop the brakes and the abs system did not activate and the vehicle did not stop. Please describe.tt

Recall # 96v099000, chrysler/brakes: hydrualic: anti-skid system. Recall work was performed on march 31, 1998.several days later , the abs warning light came and is still on. Consumer will be contacting dealer about this problem.

Replaced abs pump, also abs light comes on.tt

Had abs replaced less than a year ago, experiencing failure again.tt

Consumer received a recall notice for the abs light defect. Consumer had recall repaired and still the problem reoccurred.

When applying the abs brakes in any type of weather or speed, the abs brake light comes on and the brakes fail to stop the vehicle.consumer states dealer replaced pump, however this did not remedy the problem, dealer can not find problem.

Antilock brake warning light illuminated. *sd

Ea95-016, active, loss of brake effectivess, in for repair to replace entire braking system.tt

Abs system failure.tt

Abs anti-lock system warning light/brake light came on, had to replace the abs brakes.

Brakeswon't stop vehicle. Consumer has had several problems with these brakes.

Hydraulic brake assembly leaking-causing auto not to stop upon demand.tt

Noisy brakes. *sd

Brake calipers replaced. *sd

Brake system failure, replaced calipers, and pads because of excessive wear every few months.tt

Calipers failed.

Brake system failure, replaced calipers, and pads because of excessive wear every few months.tt

While consumer was pulling away from a red lightfront right rotors split in half, causingloss of control.consumer was able to regain controlofvehicle, and pulled over to the side of the road.

Rotors failed.

Replace master cylinder. Tt

Brake pedal sticks. *sd

Abs anti-lock system warning light goes on at times, then off other times.followed by abs anti-lock system functions to failtotally reduced brakes to stop vehicle by 95% used parking brake to achieve stop.

Steering wheel noise. *sd

Steering wheel broke off from column while driving.tt

Power steering loss has been experienced. Please describe.

Power steering pump failed.

Noise from engine area. *dsh

Power steering pump constantly whines.

Power steering pump went out and could not steer vehicle.tt

Have experienced power steering failures, steering belt tensioner was replaced twice.tt

The steering tensioner belt has fractured several times and caused loss of steering. Please describe.

The steering belt tensioner has fractured. Please describe.tt

Power steering pulley failed. *sd

Steering belt tensioner makes chirping sound; repaired/replaced before actually causes any steering problems.tt

Steering became hard, resulting in no steering ability, replace belt tensioner and belt.ttdealer replaced serpentine belt and belt tensioner.

Vehicle was hit by a cart and dented the door, consumer saw another cart hit another vehicle which did not cause any damage, the consumer feels that the design of vehicles today are weak compared to the older ones.

Vehicle bottoms out with passenger's in rear seat.

Rear shocks failed.

2 good year tires failed.

Car intermittently lunges forward; car intermittently stays in neutral when accelerating.

While driving vehicle throttle cable stuck in a open position , and the pedal will not move, rpms went up to 4000.

Wheneverheater is turned on vehicle would fail to heat up. Problem is listed on recall(#91v004000), but not for this vehicle. Contacted dealer & mechanic ordered parts. Mechanic informed owner/manufacturer a month later than recall notice.

Water leaking into area above heater blower motor resistor block may result in corrosion and or fire. Consumer took car in for repair . Consumer was told that there was a safety recall on the vehicle,manufacturer contacted. Vin number given . Manfufacturer stated vehicle was not under recall. Blower resistor had rusted due to water intrusion.the connector had built up resistance from poor connection and burned the resistor.

Water leaking into area above heater blower motor resistor block may result in corrosion and or fire. Consumer took car in for repair . Consumer was told that there was a safety recall on the vehicle,manufacturer contacted. Vin number given . Manfufacturer stated vehicle was not under recall. Blower resistor had rusted due to water intrusion.the connector had built up resistance from poor connection and burned the resistor.

Consumer was traveling about 25mph on highway and without prior warning another vehicle veered into consumer's vehicle.upon impact, airbags did not deploy.dealership was aware of problem.while consumer was trying to turn, the wheel locked and a hit pole and building. During the accident the air bag failed to deploy and the consumer had face and chest injuries.




Read more




© 2024 All rights reserved