We found the following complaints for CHRYSLER NEW YORKER (1993)
Read complaints for CHRYSLER NEW YORKER (1993)
Driver's air bag did not deploy during front end collision; hit another vehicle.tt
Purchased car used, the computer dashboard somtimes doesn't work, was having problem with the abs anti-lock brakes,received recall letter . Please describe .
The contact owns a 1993 chrysler new yorker. The contact stated that the check engine and abs warning lights randomly flashed and remained illuminated for years. The contact also stated that the brake pedal was difficult to depress and he had to apply force each time the failure happened. The vin was not included in nhtsa campaign number: 96v099000 (service brakes, hydraulic). The vehicle was taken to three different dealers who provided various diagnostics and repairs, which did not prevent the failure. The check engine and abs warning lights continued to illuminate and the brake pedal was still hard to depress. The vehicle was not repaired. The manufacturer was notified of the failure and provided no permanent remedy for the condition. The vin and failure mileage were not available.
After seeing recall on internet i took auto to local dealer ferman chrysler, npr<fl with notice said they didn't know about it and had no parts tho showed him printout about the recall.never received letter from mfr. Motor mount has been banging since around sept. And chugging had a tuneup to fix and ferman chgd me 153. To fix sparkplug fit and wrote on form that my motor mount was shaking without attempt to fix.svcman extremely rude said he didn't have time to check brakes & i was holding up the line (my appt. Was at 9 ami was there on time) said he might take a look around noon if they could (i had to leave it overnite )if i have additional damage from this motor mount thing are they responsible?? i reported the svc rep to the mgr who was nice but still no fix!!!!ui t to i.
Pistons failed.
3 of the engine mountsbroke, leaving insufficient support for the engine. Dealer said engine mounts needed to be replaced.
When turning steering wheel, system makes grinding noise. Consumer thinks belt tensioner could be related. Please describe details.tt
Pe95-012 active, belt tensioner broke while driving.tt
Engine failed. *sd
(see your number 98v184ooo)in may of 2000 i detected a leak frome my engine. At that time my mechanic found a leak from the injector o rings and one injector. He replaced the o rings and the injector.now this week i detected another fuel leak from my engine. This time, on 01/12/2001, my mechanic found another leaking injector, and replaced this and all the other original injectors.since this is the same defect as 98v18400 for the chrysler 3.5l eigine , i believe my car should be included in the recall. R ring and replaced all thefound anothe o ring leaking andmy
Complete engine failure.
Experience belt tensioner fracture.ttthere was a loud noise caused by the serpentine belt rubbing on the brake line, fortunately consumer was traveling at a slow speed and the fracture was not severre enough to lose power steering.
Exhaust springs and bolts failed.
Consumer states that fuel leaks into the exhaust manifold. Consumer is concerned that the vehicle will catch on fire.
High beam headlights fail intermittently after being in use for one hour.tt
Right headlight making noise when turned on, c ring holding bushing replaced, but caused headlight covers to close loudly and erratically.*skd
1.car hits a pothole and bottoms out2. The passenger rear suspsenion kinks and splits fuel lines above control arm, the brake line bracket was the cause of the damages. 3. Work hasnt been done as of today. But techs are telling me i have to replace the whole fuel line system do to debris in lines.
Recall 98 v 184 000/fuel leakage:fuel injection system is leaking fuel fromsealing o-rings.dealer was notified, and informed consumer that this vehiclewas not covered underrecall due to vin. Feel free to provide any further details on this matter.
(see your number 98v184ooo)in may of 2000 i detected a leak frome my engine. At that time my mechanic found a leak from the injector o rings and one injector. He replaced the o rings and the injector.now this week i detected another fuel leak from my engine. This time, on 01/12/2001, my mechanic found another leaking injector, and replaced this and all the other original injectors.since this is the same defect as 98v18400 for the chrysler 3.5l eigine , i believe my car should be included in the recall. R ring and replaced all thefound anothe o ring leaking andmy
Fuel rail gasket failure quite common on chrysler cars - cost to repair about $600. Safety issue over possible engine compartment fire if gasoline contacts exhaust header.
The fuel rail is a non wear item and a life safety issue that should be an extended warranty item.there is a similar recall on related components but dealer said this is not covered by that recall.this type of failure can lead to engine fire at startup or while running.manufacturer shuould be held responsible for repair costs.
The fuel injection pump cracked, causing gas to leak.the dealer has been notified.phthe engine control module, the #5 injector, and the fuel rail were replaced.scc
There' s a fuel leak withininjector rail, consumer contacted dealerconcerning recall 98v184000. But was informedthat this vehicle was not part of recall due to vin, althoughit experienced the same problem.
While standing next to their vehicle, consumer smelt gas fumes. Consumer then checked under the hood, and saw that their was fuel on top of the engine motor.the dealership indicated that their was a leak in the fuel pipe. Tsit was revealed that the fuel rail was leaking and had to be replaced.
Consumer received recall 98v184000 concerning fuel leakage. While driving at any speed consumer smelled gas odor inside and outside the vehicle. Dealer examined the vehicle and replaced the fuel rail. A recallwas issued for this make, model and year but the consumer's vehile was not included due to vin.
I own a mint condition 1993 chrysler new yorker with 68,000 miles on it. Last week the engine started leaking a large amount of gasoline from fuel rail onto the top of block and engine compartment. I saw where a recall campaign was issued to correct this safety condition so i contacted the local chrysler dealer to look at the vehicle. He advised me that my vehicle was not part of the recall and will not be repaired under same. How can that be?? it clearly states ""1993 chrysler new yorker"". Now he advises me that the cost to repair a leaking fuel rail/o-ring will be $536.00. This is clearly wrong. I need someone to investigate this defect.
Consumer statedthere are problems with the following:the fuel injection, the fuel leaks out of the fuel feed rail, at the swivel joints, the fuel pressure regulator, and when the engine cools down the fuel leaks all over the top of the engine and could cause a fire.the dealer was notified and stated that there isn't a recall for the problem.scc
While driving or stopping vehicle would smell fuel. Took to dealer & informed fuelinjectors were leaking. Service manager changed "o" rings, head gaskets & seals. The problem has since, reappeared.
The gas tank is leaking. Please describe.tt
In cold weather the front hood would not open,took to dealer to replace latch.
The contact owns a 1993 chrysler new yorker. The contact stated that while in parked the trunk erroneously opened and failed to close. The vehicle was not repaired and the manufacturer was notified. The vin was not available. The approximate failure mileage was 67,000.
Speedometer and odometer failure.
Transmission jump sometime it don't shift right .
The transmission broke down with just 15,000 miles.please describe.tt
Know defect in both controller and seal failure at low temperature ,justn like the space shuttle.
Auto-tran: transmission slips; does not engage in drive gear properly; feels as though vehicle is pulling backwards.tt
Transmission does not shift up from second, stalls in reverse
Original problem was failure to shift to overdrive(went into limp-home configuration) after stopping it did shift but eventually failed to shift at all.this ocuurred on a trip out of state.
Noise and thump in front end. Probable cause transmission.tt
Transmission and transmission controller failed. Yh
Transmission and transmission controller failed. Yh
Axle shaft, wheel bearings, and pads failed.
I had to replace the transmission on this chrysler -- people stop me in malls, supermarkets and ask me if i've had trouble with the transmission as they have -- all the way back to 1990 everyone i've spoken to that has had a chrysler van, new yorker, dynasty, etc. Has had major transmissions problems and/or has had to replace the transmission.in speaking with my local aamco transmission reps and continental transmission rep (a buffalo store) -- chrysler cars are their number 1 repair.i had occasion to speak with the vp of customer service for aamco at the executive offices in pa -- he also reiterated that chrysler is their number 1 repair.this should be looked in to.with all of the chrysler repairs i've heard of just in the buffalo area alone, nationally their has to be thousands of consumers who have incurred a major expense.please please investigate this.when i purchased this car from an elderly man in 7/2000 it only had 19,025 miles on the car and it was in showroom condition.around 21,000 miles the car started to have hesitation problems and i didn't know it was the transmission.one local buffalo transmission shop indicated that the computers operating the transmissions were bad and they've had to sell many of them.thank you and i really appreciate an investigation.
The transmission failed causing the vehicle to jerk when changing the gears from park to drive.nlm
Seat belt unlatched by itself upon a frontal collision.tt
The contact owns a 1993 chrysler new yorker. The contact stated that the check engine and abs warning lights randomly flashed and remained illuminated for years. The contact also stated that the brake pedal was difficult to depress and he had to apply force each time the failure happened. The vin was not included in nhtsa campaign number: 96v099000 (service brakes, hydraulic). The vehicle was taken to three different dealers who provided various diagnostics and repairs, which did not prevent the failure. The check engine and abs warning lights continued to illuminate and the brake pedal was still hard to depress. The vehicle was not repaired. The manufacturer was notified of the failure and provided no permanent remedy for the condition. The vin and failure mileage were not available.
The abs pump went out on the vehicle on august 30, 2013.it has been at the dealer since september 4, 2013.i have information stating that the pump is covered under a lifetime warranty and chrysler corporation has given me the run around on it saying that it does not mean lifetime since it failed again after the original recall repair.i am sorry but i thought lifetime meant lifetime according to the documents that i have and read.they refuse to provide me with an alternate car to drive so i can get to work stating that is not covered either.they are the poorest excuse of a business that i have ever dealt with and tell you something different with each customer service representative you speak to.they cannot even tell the same lies twice.i was first informed that they couldn't get the parts, then told they were on back order and now i am told they do not have an eta for the parts.i will not advise anyone to purchase any of their products since they do not honor warranties or stand behind their products.
The contact owns a 1993 chrysler new yorker. The contact stated that while driving approximately 30 mph, the contact approached a traffic signal and when the brake pedal was engaged, there was a delayed response. The vehicle was towed to an authorized dealer for diagnosis. The technician stated the failure was contributed to the abs. The vehicle was not repaired. In 2008, the vehicle was repaired under a recall associated with nhtsa campaign id number 96v099000 (service brakes, hydraulic). The manufacturer was notified of the problem. The vin was not available. The approximate failure mileage was94,000.
The contact owns a 1993 chrysler new yorker. The contact stated that while driving 15 mph, the vehicle failed to respond to deceleration attempts. The contact also stated that he had to pump the brake pedal until the vehicle stopped. The vehicle was taken to the dealer for inspection but they could not determine the cause of failure. The vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was 92,000.updated 8/27/15
Frequent issues with abs seizing. Was in shop most ofsummer 2015. Brakes need repairs again, and original shop is refusing to address or repair.r 320,000 of this model had already been recalled !!!filed with nys attorney general case 2015-1251639
I have a 1993 chrysler new yorker, which has a recall on the abs system, i had the system replaced by hahn motor company, yakima, wa.last week, july 21, 2003, the abs and brake lights started coming on again - i called and made an appointment with hahn motor company to have the vehicle fixed.the lights have been on the entire week and this morning when i took the vehicle in - they have had my vehicle all day and are now telling me the system has now decided to work correctly and they cannot find any problem.
Axle shaft, wheel bearings, and pads failed.
The contact owns a 1993 chrysler new yorker. While driving 30 mph approaching a stop, the contact applied the brakes but the brake pedal extended to the floorboard. The vehicle was taken to a local mechanic who informed the contact of recall 96v099000 (service brakes, hydraulic: antilock) and advised her to take the vehicle to an authorized dealer. The vehicle was taken to an authorized dealer who refused to perform the recall repair. The contact called the manufacturer who stated that the recall had a lifetime warranty. The failure mileage was approximately 65,000 and the current mileage was 66,763.
The contact owns a 1993 chrysler new yorker.the contact stated that the brakes on her vehicle suddenly felt as if more pressure needed to be applied when the pedal was depressed.the brakes pulsate when braking on slick surfaces.the abs activates on dry pavement and slows the vehicle down; therefore, more pressure has to be applied to the brake pedal.a mechanic stated that the abs pump was not activating properly.the dealer could not duplicate the failure.nhtsa campaign id number 96v099000 (service brakes, hydraulic:antilock) was referenced.the current mileage was 104,500 and failure mileage was 99,817.
Dt:the contact states there is nhtsarecallcampaign 96v099000 concerning anti lock brakes. The vehicle was taken to dealerfor diagnostic test, and according to the test, the problem was related to the recall.the dealershipmaintained it was not a problem,and will not perform the recall work.the manufacturer was called, and based on the dealership'srecommendation , they also refused to repair the vehicle.
Anti-lock brakes light on buzzing underneath hood power brakes appears to switched to manual.
I have a 1993 chrysler new yorker, which has a recall on the abs system, i had the system replaced by hahn motor company, yakima, wa.last week, july 21, 2003, the abs and brake lights started coming on again - i called and made an appointment with hahn motor company to have the vehicle fixed.the lights have been on the entire week and this morning when i took the vehicle in - they have had my vehicle all day and are now telling me the system has now decided to work correctly and they cannot find any problem.
Abs brakes are inoperative.when applying the brakes the pedal is hard and it vibrates.vehicle was takento the dealer for inspection, but dealer could not determined the cause of the problem.mechanic contacted consumer that brake pump was under recall.consumer went to dealership but refused to repair vehicle.*la
Antilock brake pump failed causing vibration/extended stopping distances.*aw
Anti-lock brakes light on buzzing underneath hood power brakes appears to switched to manual.
Consumer contacted the dealer in reference to recall 96v09900, manufacturer's recall 68. , dealer states parts are not available. Consumer currently experiencing problems with faulty brakes. Please provide any further details.
Abs brake failure prior to/after recall repairs,still experiences problems with abs light coming on and pedal becoming very hard.(96v-099).
Purchased car used, the computer dashboard somtimes doesn't work, was having problem with the abs anti-lock brakes,received recall letter . Please describe .
While drivingvehicle will lose brakes. Problem is intermittent. Contacted dealer, and the dealer was not iwlling to do anything.
When brakes are applied, they pulsate.tt consumer states when driving and put on the brakes, the vehicle begins to shake, it feels like the tires are on a wash board and continues to shake until the vehicle comes to a complete stop, consumer was advised that rotors are warpind.
Brakes failed causing vehicle to pull to the right.
When applying the abs brakes the pedal nearly traveled to the floor,causing extended stopping distance.alsoextreme pressure was used to get the pedal to move. Cause unknown.please give any further details.
This car has had many steering and braking problems.
Fluid is leaking from hydraulic unit, a pint a day is added to unit to keep it from drying out. Consumer went to a dealer in town, and one dealer stated that fluid was being over filled. Second dealer confirmed a leak, and ordered the part for repair.
When brakes are applied, they pulsate.tt consumer states when driving and put on the brakes, the vehicle begins to shake, it feels like the tires are on a wash board and continues to shake until the vehicle comes to a complete stop, consumer was advised that rotors are warpind.
Brake calipers failed.
The brake pads failed.
Brake rotors failed.
Power brake failure; hard pedal; no power assist; slow stopping;valve installed; rotors replaced; rotors remachined. Tt
This car has had many steering and braking problems.
When turning steering wheel, system makes grinding noise. Consumer thinks belt tensioner could be related.ttconsumer was advised maybe power steering pump or rack an pinion.
Vehicles steering belt tensioner fractured replaced 2 times.tt
When turning steering wheel, system makes grinding noise. Consumer thinks belt tensioner could be related.ttconsumer was advised maybe power steering pump or rack an pinion.
Pe95-012 active, tensioner belt broke while driving loss of steering.tt
Experience belt tensioner fracture.ttthere was a loud noise caused by the serpentine belt rubbing on the brake line, fortunately consumer was traveling at a slow speed and the fracture was not severre enough to lose power steering.
When vehicle is driven over a snowdrift a certain way, the serpentine belt pops off the bottom pulleys.this causes vehicle to lose power steering, heater/cooling, and alternator power.
Steering belt tensioner dropped out onto ground while making a turn. Tt
Replaced/repaired power steering belt tensioner.
Power steering reservoir cracked causing leakage.
When turning steering wheel, system makes grinding noise. Consumer thinks belt tensioner could be related.ttconsumer was advised maybe power steering pump or rack an pinion.
Vehicle mouldings around vehicle are all separating from vehicle due to poor design and craftsmenship.
Consumer was informed by mechanic the control arm needed replacing. *jg
Consumer was informed by mechanic the control arm needed replacing. *jg
Rear air suspension won't pump up, air pump only runs for 30 seconds, the left air bag leaks and the right leveling sensor is inoperative.consumer has taken vehicle to dealership for repair to the air suspension, was informed the left air bag, leveling sensor, and a new pump.*jg
Rear air suspension won't pump up, air pump only runs for 30 seconds, the left air bag leaks and the right leveling sensor is inoperative.consumer has taken vehicle to dealership for repair to the air suspension, was informed the left air bag, leveling sensor, and a new pump.*jg
The pulley's that the serpentine belt is on, do not line-up, it results in the belt shredding, and i was told that the belt might be thrown off all together. I have had it fixed once but it's starting to happen again.
Cruise control does not hold vehicle back when travelling down steep environment; goes up to nearly 90 mph before driver can stop/slow down.tt
While driving vehicle between 30-40 mph gas pedal became stuck,causing speed to increase. Vehicle had to be placed in park and hand brake pulled to stop vehicle. Cause unknown.
Turned heater on, after approximately 20 minutes condensation and fog formed on all the windows, turn heater off, to no avail.
Read more
