We found the following complaints for CHRYSLER CONCORDE (1999)
Read complaints for CHRYSLER CONCORDE (1999)
The vehicles clock spring failed prior to recall notification.the recall was on various chrysler vehicles except the concorde.the consumer has requested reimbursement.*nlm
Vehicle involved in head-on collision. Airbags failed to deploy allowing driver to suffer severe injuries. If air bags had deployed, driver would not have gone forward in vehicle. Driver struck head on steering wheel and broke left hand on tilt-wheel handle. Are there other instances of air bags in chrysler products not deploying? this is supposed to be the main safety feature and it failed big time.
Consumer was pulling out of parking garage and putvehicle in gear and the vehicle pulled off on its own very fast, causing the consumer to crash into another vehicle. Air bags did not deploy . Dealer has been contacted.
While traveling about 30mph on highway andwithout prior warning another vehicle veered intoconsumer's lane and hit vehicle head ondriver's side. Upon impact, airbags didn't deploy.dealership is aware problem.
Dt:the contact was driving on october 3, 2005 when she ran over a ladder that was in the middle of the road.this caused the contacts' vehicleto be hit by another vehicle, causing the vehicleto t hit the brick wall on the freeway.then, another vehicle hit the contct'svehicle. Upon impact,both of the frontal airbags failed to deploy.the vehicle was totaled after the crash.the contact'sneck was sprung due by the airbag failure. The vehicle has not been inspected to see why the airbags failed to deploy
Nhtsa#02-v-293-000: the vehicle experienced the same problem as stated in recall # 02 v 293 000.the clockspring was broken/air bag light stayed on, and there was no horn(electrical failures).(model lxi)scc
Immediately after starting car & putting it into gear, it took off at a high rate of speed, even while foot was on brake pedal.driver served to avoid parked cars and went through a fence hitting a ditch, went across a street, hit another ditch before stopping. Also, there was no deployment of air bags. *cj
The contact owns a 1999 chrysler concorde.while driving 35 mph, the vehicle hesitated, vibrated, and then shut off.the contact was able to restart the vehicle and drove to a mechanic.the mechanic stated that the engine caused the failure.as of december 10, 2007, the mechanic had not repaired the vehicle.the current and failure mileages were 83,000.updated 3/11/08 the consumer stated while driving the headlights blink within the first 5-10mins and the dealer will not fix the defect which the consumer was informed the computer was the problem. Updated 03/11/08
Problems with vehicle's heater, engine making knocking noises and slow acceleration.*mrthe heater stopped working intermittently which lead to a build up of heat in the engine cabin, which in turn lead to a build up of sludge.during acceleration, the vehicle rattled and vibrated and it did not accelerate smoothly. The consumer was informed that the entire engine block needed to be replaced, which was the cause of the problems. Also the front window and power mirror were inoperative, the dealer found a bad window motor.
6 times my 1999 chysler concorde 2.7 motor was taken to dealership for problems with the motion sensor/cause motor to uphift or downshift at random or get stuck in gear...last week a loud rattling in the motor 74000 miles...engine replacement ...$3,000
Problems with trunk release on the dashboard, driver's window, seat belt retractors and the computer chip. *mr ph
While traveling highway speed, the automatic transmission down shifted abruptly with no warning.the owner was able to coast down a ramp onto a side street.the cause stated by a mechanic was that the torque converter destroyed itself. Tsthe motor that operates the drivers side window failed.an electrical component failed causing the battery to discharge.consumer has been refused any compensation for the failure of the torque convertor.*jg
Takata recallcar caught fire in the front of the car (defrost vents) i went inside the store while my car was parked on the street when i came bac my car was smoking. Fire department said it was caused by fan motor fail.
Since 2010, the car has had many electrical issues that have resulted in over 5,000 dollars in repairs and the problems continue to persist.in 2010, the car began having intermittent lighting issues and failure of the trunk latch opening mechanism. In aug 2010, the bcm was fixed/replaced.since then, the a/c has become the problem that has led to thousand of dollars of repairs.the problem is that intermittently the a/c will not respond to changes in the temperature controls and only 180 degree air comes out.the dealer has replaced almost all mechanical parts of the a/c and the electrical controls with the exception of the bcm.the problem continues and now the so call new bcm is no longer under warranty.
The interior lights illuminated on their own. Consumer believed there may be a possible electrical problem.
The bcm on the car has been shorting out.the lights turn off the dash lights turn off the fuel gauge drops out the heat and a/c won't work all at once.the dealership replaced the bcm once.the problem came back less than a year.now the dealer said the bcm has shorted out the junction box or the junction box shorted out the bcm.
Nhtsa#02-v-293-000: the vehicle experienced the same problem as stated in recall # 02 v 293 000.the clockspring was broken/air bag light stayed on, and there was no horn(electrical failures).(model lxi)scc
On 6/12/03 i filled out a vehicle owners questionnaire on a 1999 chrysler concorde, vin [xxx]. On 8/02/02 i purchased this chrysler concorde with 48,580 miles.on 8/15/02, i took the car back to [xxx] because of electrical problems, car leaking oil,brakes sticking,and air, heater,defrost,ventilation problems.upon arrival to [xxx]on 8/15/02 to drop the car off to be serviced there were 48,620 miles on the odometer. After receiving a phone call from [xxx]dealership stating "that the car was ready." "and had been serviced." after arriving and getting in the car, i noticed that the odometer had been changed, because it was now reading 48,883 miles.i then questioned [xxx]about the additional miles and was told "been everything had fixed."on 4/15/03, i was back at [xxx]having electrical problems in the dashboard. And the air conditioner was blowing out hot air.in the month of may 2003, i received a recall notice about the driver's seat bolt being defective, which may break causing the seat to suddenly recline. I took the car in on 5/27/03 to have the bolt replaced. After being at the dealership for about two minutes i was told that "the car was ready to go." i asked if the bolt had been replaced? i do not believe it had because it was not gone long enough. I also had to request a customer's copy of the invoice. When i received the invoicei notice that the invoice stated that the car wasgray. The car is black.pleaselookinto this matter.thank you[xxx] *sccinformation redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6).
While replacing the battery the jack broke andvehicle fell to the groundand consumer was under the vehicle. Consumer sustained major injuries and was transported to a hospital. Consumer will contact the manufacturer in the near future.
Car has popping sound around left front wheel,all but one window is off track and cant use.have to bang key on end to get it to turn ignition over.car shakes when braking.wont stay in alignment.uses oil from first day we bought car.when windows did work they snapped shut loudly.this is a smooth riding car but has way to many problems.also the tv cable broke and had to be replaced which was the only component that wasnt covered on the warranty.kinda strange since the car wont budge without it..i am sorry i ever bought this car.i am paying for a vehicle that will be trash by the time it is paid for.
Dt: in april 2005 owner put key in the ignition switch and it gotstuck.the key would get stuck more and more often, then wouldn't turn at all. The key would get stuck in the ignition, allowing the car to be left with the key in it. Once the key was stuck in the ignition for weeks, and had tobe repaired by a locksmith. The locksmitih advised consumer that this was a common problem with these type of cars. It was a 1999 chrysler concorde. The problemreturned becuase the key sometimes getting stuck.owner couldnot turn the key over.if consumer fiddled with the key it will turn over.dealership advised consumerthat the pin inside the ignition interlock broke off and then it wont work anymore. The ignition switch was eventually recalled 04v021000, but dealership advised that it was not related to this problem with the ignition.
While parked, consumer smelled smoke and noticed that smoke was coming from under the hood. Consumer put fire out, and vehicle restarted 15 minutes later.consumer then unpluged battery.consumer stated the starter was replaced.*et
Problems with trunk release on the dashboard, driver's window, seat belt retractors and the computer chip. *mr ph
While parked, consumer smelled smoke and noticed that smoke was coming from under the hood. Consumer put fire out, and vehicle restarted 15 minutes later.consumer then unpluged battery.consumer stated the starter was replaced.*et
Steering rack corroded, dealer replaced rack and pinion.all four power window motors burned, dealer replaced.heater fuse box was burned, dealer replaced.
On 6/12/03 i filled out a vehicle owners questionnaire on a 1999 chrysler concorde, vin [xxx]. On 8/02/02 i purchased this chrysler concorde with 48,580 miles.on 8/15/02, i took the car back to [xxx] because of electrical problems, car leaking oil,brakes sticking,and air, heater,defrost,ventilation problems.upon arrival to [xxx]on 8/15/02 to drop the car off to be serviced there were 48,620 miles on the odometer. After receiving a phone call from [xxx]dealership stating "that the car was ready." "and had been serviced." after arriving and getting in the car, i noticed that the odometer had been changed, because it was now reading 48,883 miles.i then questioned [xxx]about the additional miles and was told "been everything had fixed."on 4/15/03, i was back at [xxx]having electrical problems in the dashboard. And the air conditioner was blowing out hot air.in the month of may 2003, i received a recall notice about the driver's seat bolt being defective, which may break causing the seat to suddenly recline. I took the car in on 5/27/03 to have the bolt replaced. After being at the dealership for about two minutes i was told that "the car was ready to go." i asked if the bolt had been replaced? i do not believe it had because it was not gone long enough. I also had to request a customer's copy of the invoice. When i received the invoicei notice that the invoice stated that the car wasgray. The car is black.pleaselookinto this matter.thank you[xxx] *sccinformation redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6).
Yesterday i had to go to the hospital because the trunk lid fell on my neck when i was unloading my trunk.this car has an electrical trunk that opens and the trunk also, has a spring air rod that controls the hold of the open trunk.i know this failed because the trunk just lost its hold all of a sudden and landed on my neck.as i tried to lift it from above me (its very heavy- big trunk), my left hand indexfinger broke and my left arm and hand are in pain.not to mention, the severe pain i am undergoing with my neck. I also bled a lot and immediately went to the emergency room.i believe this can be a manufacturing defect due to the excessive weight of this trunk door and the device being relied on for the control of trunk.
The contact owns a 1999 chrysler concorde lxi. While driving approximately 70 mph on normal road conditions there was pressure applied to the accelerator pedal and unexpectedly, the speed rate reduced to 20 mph. The contact was able to drive on the emergency lane with caution and suddenly, the speed rate increased to 70 mph. The contact was able to continue driving. The vehicle was taken to an independent mechanic for diagnostic testing; however, the technician was unable to duplicate the failure. The identical failures occurred on four separate occasions. An independent mechanic on two separate occasions reset the crank shaft sensor code. The failure continued to occur after the repair was made in addition, the vehicle stalled intermittently. The contact had concerns of the safety risk involved.the failure and current mileages were 121,000.
Dt: on june 23 2005 while driving down the road the engine began to jump. Owner was going 45 mph. There were no warnings until the engine light came on almost at the same time the engine began to jump. The power steering and brakes still worked so owner slowed down , and got into the right lane in case the car stopped completely.car was taken to the mechanic who stated that it was the timing chain and other factors in the engine.manufacture has been contacted, but will not cooperate with owner.the car had only been driven for five minutes.there were no other problems with vehicle. Car is now in shop for repairs.
While drving aproximately 45 mph on the highway the engine stalled. Consumerwas then able to pull to the side, avoiding any accidents.
Dt:the contact stated the engine died while pulling from a parking lot.she was unable to restart the vehicle.it was towed to a dealership service department.the water pump failed,and the timing chainbroke.the problem occurred because of a sludge build up in the engine.the service dealer replaced the timing chain, the retention for the timing chain, water pump, and other parts in the area.the engine was also cleaned thoroughly.the check engine light came on previously.however, the dealership was unable to diagnose any problems at that time.updated 01/04/06.
While driving 55 mph the vehicle stalled.the consumer managed to pull over and had the vehicle towed. The cause has not been determined.*sc
The chrysler 2.7 engine. Mine ceased to exist august 16, 2005 co-incidentally one month after i had the ac/evaporator, cooling system fixed. For the second time! after reviewing many of the complaints of numerous websites including consumer auto safety, i absolutely cannot believe chrysler can still make denials about product liability and get away with it. For all the complaints in which the engine failed while on the highway and loosing power steering, a death would have to occur first in order for chrysler to issue a recall. The damage to them would be tremendous having known all along about these complaints of faulty engines as other manufacturers have had to admit! i currently was offered by impartial services group hired by chrysler a mere 5,000 for my dead defaulted engine. I denied it, because the estimates were over 7,000. And these "replacement" engines had the same miles as mine when it died, and i was given a mere 90 day warranty. This is the craziest thing i have ever heard of. Why cant one of these organizations enforce this recall? i currently have my dead vehicle sitting on a friends driveway by an intersection with a lot of traffic. Attached with a sign chyrsler engine oil sludge! and that is where it will sit until i have a full remedy. This is my right!
- the contact ownsa 1999 chrysler concord.the contact stated that the vehicle had 44548 miles when purchased on05/01/2002. The vehicle was 3 years old at that time.the contact stated that 2 motors seized. The contacthad driven the vehicle approximately 16,000 miles when the first motor failed at 60,000 miles with no warning.the contact was driving 55 - 60 mph when the motor began clicking very loudly.the contact stated that the weather was very nice.the second time this happened the vehicle was being driven between 25 - 35 mph and the motor again began clicking, and seized.the contact turned the car off, and had it towed to theregular mechanic.the mechanic inspected the vehicle and determinedthat the motor had seized.the contact stated that the vehicle had just had two oil changes because sludge was found in the oil.a synthetic oil was put in thevehicle to try and combat the sludge.the contact stated that she has been trying to get another motor without any success, and the vehicle was sitting in storage with the mechanic.the current mileage was 90000.
After the consumer changed the oil, the engine light illuminated the dash board. A little whilelater, the light was on and off, suddenly the engine stalled and never startedagain.an independent mechanic indicated to the consumer that 2.5 engine was garbage, andneeded to be replaced. The consumer believed the problem was a bad oil pump.
I had a a/c diagnostics test at maxwell(chrysler/plymouth) 6905 i.h. 35 south austin, texas 78715 on april 5, 2003. Service advisor: 9 doug shaw told me i needed fan belts(two at $165), rt cooling fan motor soon($236.00 for cooling fan motor, and other engine cooling fan motor replaced but if cooling fan motor only at $322.14), evaporative coil(at cost $1035.00), evac&recharge-add dye($145.00 cost) for testing. I had someone else put on the rt cooling fan motor and put fill it up with freon. It is still not working properly. Sometimes it will come on and blow cold air sometimes it won't. But it will not come on right away.driver's door radio door speaker has a buzz.
The engine started to make a wierd noise. Vehicle was towed to dealer, dealer stated engine completely failed due to slug build up.
Engine light came on at about 30 mph and i heard a light ticking sound.engine was shut down immediately and car was towed into a garage. I was told the engine seized , and would cost $5,000 to replace e it. My car has 87000 miles,but i contacted chrysler anyway and was told they couldn't help .my car sits because i cannot afford the cost of a rebuilt engine.
While driving down i-45 in conroe, texas, my engine sputtered, jerked, and died.as you know when you lose engine power, your steering wheel becomes locked up and its almost impossible to control the car.it has died on me before but on back roads almost home or at an intersection.i didn't realize the seriousness of it until it happened on the freeway and there are people coming up on me doing 70-80 mph and i am quickly coming to a dead stop.
When driving consumer heard a knocking noise, and sludge coming from the engine.consumer had the vehicle towed to thedealership,but dealership did not resolve the problem.
The contact owns a 1999 chrysler concorde.the contact stated that the abs light illuminated and she heard a noise in the engine compartment.the mechanic stated that the pump motor circuit for the abs failed and caused the light to illuminate.the approximate cost to repair the vehicle was between $1,500 to $2,000.the front rotors were replaced in april of 2006 and in september of 2007.in january of 2007, the front driver side bearing was replaced.the mechanic stated that the failure was due to poor design and cheap parts.the air conditioner also began to leak.the mechanic stated that there was a hole in the suction line because of the design, and it rusted and rubbed through another part of the vehicle.the air conditioning suction line was replaced in september of 2007.the leak could have potentially caused a fire.the mechanic stated that the power steering kit needed to be replaced.the vehicle could easily rust into the frame and condensation could collect.the vehicle is currently hesitating and surging.the current mileage was 78,100 and failure mileage was 78,000.updated 03-04-08 the leak of the power steering hose could cause a fire. Updated
2.7 liter engine failed on 1999 chrysler concorde with 65,000 miles.chrysler claim they do not have a problem with this engine and has refused to offer any assistance on the repair.estimated cost to repair is $6,000.
The vehicle was on the road when all of a sudden the check engine light turned and within seconds the engine shut down. Manufacturer will be contacted by owner.
1999 chrysler concord2.7 liter engine-has history of engine failure.my 1999 concord now has smoke coming from the exhaust pipe, rough idle when cold, and also has intermittent oil pressure light illumination (all within 24 hours of the car being serviced for the oil light problem).
Experienced engine failure due to sludge build up caused by car heater.
My car shut off while at a stop light.it started back up, but making this awful rattling noise.i had a auto shop tell me a few things and i paid to get a few repairs that cost me closed to $1,000.then before i could get a repair done to the timing chain of my '99' concorde, it shut down on me as i was leaving work.i had to get it towed from the middle of traffic, during rush hour and it is now in my garage waiting to be repossessed.
Entering on-ramp to interstate. Car starts clunking, vibrating, clicking. Car dies on the on ramp on an interstate. Car died at 5:30 pm, it's dark out and almost hit by numerous cars speeding up to merge onto the interstate. 2 small children in the backseat. Cannot remove until help arrives because it is 5 degrees above zero outside.towed car to local repair shop. Timing chain tensioner needed replacement. Clean sludge from oil pan. Found oil sludge and metal shavings in the oil pan and the oil screen.$834 in repairs and now engine has very loud knock. Repair shop tells me the engine is basically shot and nothing can be done to fix or salvage.
I have a 1999 chrysler concorde lx with a 2.7 engine. My wife was driving down an access road at about 45 mph when the car started losing power. She thought it was because of the air conditioner but when it stopped it died. No warning lights came on to tell her anything was wrong. Did not notice temperature getting hot. Had it towed to mechanic shop. Mechanic said it had water in the block with the oil. Said it needed a new motor. To rebuild mine, at his cost, would be $4500.00. This is without the labor of removing and reinstalling motor. Other option- wait until a used one becomes available. That would cost $1700.00-- $2700.00.i have found many similar stories on this web sight. Bdm.
Reference number: [xxx] [xxx]. This is a defective product liability issue. I want financial compensation for the repair of my vehicle. Daimler .chryslerand its representatives are directly responsible for the mechanical failureof this vehicle. Faulty engine design, and incorrect maintenanceperformed.vin# [xxx] 1999 concorde11/04/03 repair orderinvoice#[xxx]:replace camshaft sensor. Mileage 83117.02/02/04 repairorder invoice#[xxx]:replace camshaft sensor. Mileage 88097.03/22/04invoice# [xxx]:a/c compressor seized, replace engine. Mileage91065.estimated repair cost $7740.00 please contact me as soon aspossible.thank youinformation redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6)
Dt*:the contact stated while driving 65 mph on the interstate a loud noise was heard and the vehicle stalled.the vehicle was maneuvered off the road and towed to the dealer who determined the crank bearing fractured and the engine needed to be replaced.
The contact owns a 1999 chrysler concorde.while driving 45 mph, the oil light illuminated intermittently then the engine shut off.the contact stated that the vehicle had an oil change the month before the failure.the mechanic stated that the engine was seized it needed to be replaced.the current and failure mileages were 107,000 miles.
I was driving my 99 concorde on a curvy road when engine started knocking and died. I had only manual steering and no brakes. It took all of my strength to keep it from going off a curve. I called the tow service and had it towed to a garage. They said a rod bearing had gone out of the engine. After numerous calls to chrysler and the district mngr. He had it towed to the dealership where i bought it. To rebuild my engine (with their discount) was $6300.00. Another rebuilt engine was $7300.00 a new engine was $8300.00. I have records this car was babied and regularly serviced. Chysler has denied their problem with hundreds/thousands of the 2.7 l engines saying the sludge build up in the engine causes the blow up. They blame the owners for poor maintenance. So now i have a lawn ornament in my driveway. I refuse to pay this. I can buy another used whole car for that. I've been a chysler man for years as was my father. I have 3 now. When they are gone. That's it. Believe me i will research my next auto i purchase.
Oil sludge causing engine failure.
Dt consumer states that on august 20, 2005 the vehicle completely came to a stop while going at 40 mph, the vehicle lost power. Consumer hadittowed to the dealer . They said the cam shaft cracked and broke, and there was metal flying in the engine. The vehicle would turn over, but would not start. There was no forewarning prior to this incident. The dealer said this was a common problem.the engine was known to be a sludge builder whether highway or city driving. Consumer contacted the manufacturer, they said there was no problem with the engine.
I have a 1999 chrysler concorde with a timing chain problem....this is my second concorde after the other got stolen....and after i paid $3800 to repair the timing chain on it....can anything be done of this problem....i cant afford it again???
The contact owns a 1999 chrysler concorde lx. The contact was driving 40 mph when a clicking noise was heard from under the hood. The contact also mentioned that the check engine warninglight was illuminated and the engine stalled. The vehicle was taken to a private mechanic where the mechanic advised that the engine needed to be replaced. The manufacturer was not contacted and the vehicle was not repaired.the failureand the current mileages were110,727.
I was hoping you could give me information about a possible class action lawsuit concerning chryslers 2.7 engibne.i have a 1999 chrysler concorde.july 30th, 2004my car started making a horrible noise and stopped running as i rolled into my mechanics place of business.he was able to listen to it and immediately told me of the problems he has seen with this engine and thought there might be a silent recall, i should take it to a chrysler dealership.i had it towed to the dealership, where they diagnosed a bad timing chain.after researching this i didn't feel that it was myresponsibility and contacted chrysler customer relations.after several calls, they finally agreed to pay for only the parts, i was responsilble for labor.by the way, my car has approx. 44,000 miles.after replacing the timing chain, i called to see when my car would be ready and i was told that the engine is still making noise.the short block and oil pump was gone, therefore,i needed to replace the engine at my cost of $5,500.i reminded them of the 2.7 engine problems, which fell on deaf ears.customer relations are of no help either, they claim that the timing chain didn't cause engine failure, but the oil pump did.they will not assist with any of the charges.i asked them to not fix it because i am trying to get help with this.i have requested a service rep. To assist with this matter.chrysler also requested to see if i had neglected the car before paying for parts on the timing chain.they found no evidence of sludge or abuse.just like everyone else, i am extremely upset about this matter.i purchased the car with the intent of it lasting longer than it has, especially with such low mileage!i would appreciate it if you could contact me with any information.
I have a 1999 chrysler concord [xxx] which i bought used from bud brown chrsyler. The mileage at the time i had bought was 55286. I had change the oil regular. At about mileage 62400 my engine fail. I come to find out pricing to repair the engine. My car engine is know to go out (2.7l). From what i understood when built the oil pump wasn't big enough to circulate the oil and cause a sludge built up. I was driving back to work when my went out and was with out my car for an month.information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6)
1999 chrysler concorde. I experienced engine failure at 105,000 miles. My mechanic has informed me thatthis is a problem that dodge is aware of and that there is a class action suit against them.
While driving the engine completely locked up. Consumerhad the first engine 2.7 replaced with a rebuilt 2.7 liter engine. In which she was told the 2.7 liter engine was the only one to fit the vehicle. This rebuilt engine was experiencing the very same problem as the first.consumer stated that transmissionand input, output sensor has been replaced.
Dt*: the contact stated while attempting to accelerate from a stop, the vehicle jerked forward and then stalled.the vehicle was towed to an independent repair shop who determined the vehicle needed a new engine.
1999 chrysler concorde begain to hiccup on the interstate. As i pulled off an exit it stopped right in the middle of a very busy intersection. The car completely shut down, not steering ability, no driveability. I was almost hit and several other cars had to avoid hitting me. There were many drivers affected and angry.
2.7 engine failure due to oil sludge on 1999 chrysler concorde lx.
Dt*: the contact stated the engine was knocking.the knocking started intermittently and has become progressively worse.the dealer determined the engine needed to be replaced due to sludge buildup.no repairs have been made to the vehicle.
Air conditioning continually goes out. As car has expired warranty, chrysler says they have no obligation to repair. I disagree. I believe that chrysler, and in my particular situation, has a faulty a/c system.
Car engine failure at 90,000 miles.was traveling on i-75 at 70 mph, engine gave no warning, just had cam shaft sensor replaced and oil sensor replaced, this was the second time for both items in the past year. Have not gave authorization to replace engine, cost estimated at 6000.00.was told by mechanic this a problem with the vechile.contacted chrysler, was told i should have bought a new vechile instead of buying a used one.this only had 50,000 miles on it when purchased, but i travel over a hundred miles to and from work daily.engine should not have failed at 90,000 miles.
Total engine failure of 1999 chrylser concorde 2.7l engine.
While driving at 50 mph, the consumer heard a loud fluttering sound under the hood of the vehicle. The vehicle immediately lost power and a few seconds later itstalled.the vehicle was towed to the dealer, who informed the consumer that the serpentine belt snapped.the dealer found the timing belt idler tensioner bolt broken off in the block andthe water pump leaking they drilled out the broken bolt and replaced the timing belt and tensioner, the engine was cranked over and the discovered that all cylinders the had no compression. Probable cause was bent valves.consumer had to replace the engine.
Another chrysler 2.7 litre catastrophic engine failure timing chains failure demolished engine at highway speed.
Consumer stated that her engine started to tick, as if she was low on oil.she states she took her vehicle to the dealer/mechanic and was told that her engine was going.she states that this makes her angry , because she has had regular maintenance on this vehicle, and it only has 60,000 miles.
Intermittently when trying to start the vehicle consumerhad problems starting it.also, while driving at any speed vehiclestalled when the brakes were depressed. These problemsoccurred thirty times since february of 2004.dealer was notified of the problem but refused to check the problem because there was no recall for stalling.
I bought a 1999 chrysler concorde that started off with no heat (replaced heater core) then had tranny fluid in the radiator(replaced radiator) now the engine seized and has anti-freeze in the oil. This all happened within a month of purchased.
I own a 1999 chrsyler concorde that has just over 40,000 miles when the engine just died.turns out thatsludge build up is the problem but the engine is ruined????i have religiously maintained the vehicle according the the manual.then i found that this a known problem with this 2.7l engine.why hasn't chrysler stepped up to inform their customers of this problem and worst yet why haven't the local dealers been informing the local customers about this problem??i am furious and will not buy another product from chrsyler,ever.i was seriously considering the new 300m becuase i love the car but no way will i purchase one now after babying this car for the last 6 years.i am heading back to the honda dealer tomoorw to buy a new honda accord.my son ss drivng my 1990 honda acoord i owned before trying an "american" made car again with 131,000 miles on it and never one problem.never again.....no chyrsler products in my furure....ever!is there any recourse??????? thanks you for your support.
Consumer advised that timing chain guide has broken twice while driving resulting in extensive engine damage.1st failure occurred in 10/01 at 34k miles.2nd failure occurred in 11/02 at 58k miles. Ts
While driving home from work my 1999 concorde with 90,000 miles on it started knocking very loudly.i had to shut the vehicle down because it sounded like the motor was tearing itself apart.had the vehicle looked at by a mechanice who said the motor needed to be rebuilt or replaced at a cost of about 3000-4000 dollars.the vehicle still sits in my driveway today making payments on it.this happened in 2004 and its now 2007.great way to back your product chyrsler by telling me i didnt maintain proper maintanance.want to see the reciepts.
Chrysler concord 2.7 engine driving down hwy oil light came on loud knocking under hood car stoppedtowed car to dealer.they said i had a blown enginei change the oil every 3 to 35 hundred miles. They said that the engine had excessive sludge. After talking to several other engine people they said that the 2.7 engine has a habit of blowing at around 75000 miles
While driving the car shut down with out warning or lights.total shutdown without power steering on busy road.the engine locked up due to engine sludge.the engine had to be replaced with new block because the poorly designed engine could not be rebuilt due to the fact that the cylinder walls are too thin.used engines are not available because the problem is so widespread.
Car stalled, oil light came on, car started making knocking noise, towed to chrysler.dealership and was told the only way to fix it was a new engine. At my expensehave since found out this is an ongoing problem with this motor and chrysler wont do anything about it, i have maintained this car with regular oil changes every 3000 t0 3500 miles. I have been told the cost is 5000.00 to replace the engine.i am devistated by this and think chrysler needs to own up to its defective motors.
Dt*: the contact stated the engine started making a tapping noise while idling.the vehicle was towed to a dealership.the dealership determined the engine seized and needed to be replaced, however no repairs were made.the vehicle has been maintained including oil changes on a regular basis.
Dt*: the contact stated while traveling 40 mph, the engine began to knock.the vehicle was taken to an independent repair shop who determined the rods were about to blow and the engine should be replaced.
Air conditioning/heating unit does not cool or heat properly. Has been investigated regularly without chrysler dealer "finding" anything.on particular date below it was a very cold morning, used heat and drove 3 kids 20 miles. Stopped for half hour, got back in car and car sounds like a diesel engine - rough and loud. I was alone with the 3 kids.asked a couple of men to listen, they thought cylinder(s) were gone as noise lowered when engine revved. (by the way, this car has had 2 transmissions already, with 73,000 miles). Limped home scared to death on interstate highway with the 3 kids.stopped at service station, told not to drive as engine was failing.called aaa and they came and towed to chrysler dealer. Dealer was unable to replicate the diesel sound and "found nothing wrong." today is nov 24th 2003 and this morning the same sound is back in my engine. The heat only works when i am moving, not at idle, and leaves a very odd smell in the car if the car is left idling with the heat on.i have a 5 month old, a 5 year old and an 8 year old, i am getting very frightened to drive this car with them in it anymore. I did an online search and found that this ac/heat problem is prevalent in this model (chrysler concorde 1999) and can create sludge in the engine that causes sudden engine failure.i want this fixed and i want you to get after chrysler about this! *la
Dt*: the contact stated while driving 30 mph to purchase a replacement tire for the vehicle, a rattling noise was heard. While the vehicle was at the independent repair shop, the mechanic attempted to restart the vehicle, but it would not start and made a rattling noise.the mechanic determined that the timing chain was broken. There were no warning signals prior to the failure. The noise began on the day of the incident. The engine was replaced 2 to 3 years prior to this incident. Through research on the internet, the contact found many complaints regarding the engine for this year, make and model. There was a class action suit on the internet as well.the vehicle had regular maintenance and oil changes performed.
Engine started making loud knocking noise.had the car towed to chrysler.chrysler reports that the timing chain came loose and caused severe damage to the water pump and engine and the timing chain, water pump and engine need to be replaced.they report that there were no oil leaks and filter and plug were in place and dealer could not explain cause. I have spoken to chrysler corp. And the dealership.chrysler agreed to help with repair until they found out the engine was damaged and needed to be replaced. The repair will be 6,700 dollars.i see there are other reports of this same problem.would like to know if others received any financial assistance from chrysler and what my next steps should be.
Was driving north on mi 31 bypass heading for schroeder motors to pick up my dodge ram pick-up truck that was in for service. Turned onto napier rd going west and heard a clapping sound like a baseball card in the spokes of a bike. I thought a piece of paper got into the fan blade. There were no warning lights that came on. Just as i pulled into schroeder motor mall the car died and that was the end. It rolled to a stop right into a parking spot. I had there mechanics look into it and he had told me that the water pump looked like it failed and caused the timing chain to slip resulting into warped valves. I was given an estimate to replace engine for about $6700.00. They were going to allow me $1000.00 for my troubles off of the bill. Mechanic put all of the parts in my trunk and i had the car towed home where it will set until i get some answers.
Here is a copy of our sales ticket that explains all of the updates that we perform on this engine.hopefully this will help you.if you have any further questions feel free to contact our customer service department at 1-800-827-7450.--oil starvation is a problem with this engine, so jasper installs the newest design oil line which has a larger diameter pipe to allow more oil flow and better lubrication. The newer design pipe has one gentle bend opposed to the original which had two 90-degree bends which tends to restrict to oil flow. --to prevent bearing failure jasper installs aluminum rod & main bearings instead of tri-metal bearings.the aluminum bearings conform to the mating surface more completely, which provides more exact clearances.the aluminum bearings are also more corrosion resistant.the original tri-metal bearings were prone to not conform well, which led to dirt and debris becoming lodged in the bearing due to excessive bearing clearances. --water pumps on this engine have been known to leak or fail.one of the issues leading up to this was due to the timing chain tensioner. It would apply more tension to the chain then was needed, causing stress on the water pump.jasper installs a later design tensioner, which applies the right amount of tension on the timing chain and reduces the stress on the water pump. Jasper installs the newest design oe water pump & water pump gasket which will seal to the block better than the original oe design. --with the use of an mls gasket, the standards for machining on the head and block have been increased to insure that the gasket can seal properly.this is to help prevent coolant from entering the oil cavities causing damage to the engine. ----jasper does not install the cam gear balancer due to a bulletin from chrysler effective 12/14/01 stating it is not needed and not serviced from this time forward. --do not remove from core and install on jasper's engine. --live run tested oil.
I own a 1999 chrysler concorde lxi.i have had numerous problems with this car since i have owned it.lot of little things. Window motors, cooling fan, transmission overspeed sensor, and the list goes on.now the air conditioner is going out, having to service it about every 2 months.why i am writing though is the steering.seems like it is going bad.i feel this is a safety issue and read many complaints on your web site concerning this.why hasn't a recall been ordered for this and the speed up issue?
1999 chrysler concorde engine failure at 90000 whille wife and children in traffic engine failure due slug build up. Mechanic said it would cost $4600.00 to replace engine still owe 11000 on it, and cant afford to repair. Mechanic said slug build up is due to oil pump design also have ac problemand have had radiator fan failure twice , speed sensor failure, broken window clips,brake shimmy , broken recliner seat bolts
I have a 1999 chysler concorde, 2.7 liter, with 85,000 miles.the engine began knocking and then the oil light then came on.i stopped the car on the expressway.after sitting i could restart the engine, drive a short distance (.1 miles) before the light would come on again until i got to an exit.the car was then towed to a garage.they have diagnosed likely bearing failure requiring an engine rebuild.the oil pressure is dropping as the engine warms up.they found metal shavings (brass)in the oil.until this problem, the engine had not knocked or had any valve noise or other issues indicating low oil pressure.i have generally changed the oil every 3,000 miles.this failure seems premature and without warning.the safety issue is that motorists are left stranded on the expressway due a possible defect involving the materials used in the manufacture of this particular engine.while the mileage exceeds the manufacturers warranty, the failure is extremely premature.
2.7 engine seized.
While driving at 40 mph, the vehicle stalled on a side street.the vehicle was towed to a repair shop.the mechanic informed the consumer" the engine had seized up and a new one was needed".the manufacturer and the dealer were aware of the problem.
While driving, the engine failed.previously there was a knocking noise.after getting off the road it did start again.this was the first time this had ever happened. The consumer took to the vehicle to the dealer and mechanicsaid the rod bearings were gone.
Dt*:the contact stated while driving at normal speeds the engine stalls without prior warning.although the engine stalls, the abs, check engine, battery, and interior lights illuminate.the vehicle can be restarted after this occurs, but continues to stall again.the vehicle was seen by the dealership,but no repairs were made.
Vehicle stopped running and would not restart.consumer left the vehicle, and went back the next day, and it started.vehicle was driven to the dealer, where they discovered sludge in the engine, and the engine bearings were defective.
I own a 1999 chrysler concord (purchased new) and was told that my engine was "shot".to replace it will cost $5,000.this included $3,800 for the rebuilt engine and $1,200 for labor.this is ridiculous!!!it has 78,000 miles on it and i have always taken it in for scheduled maintenance.for a car that cost over $22,000 to need this kind of repair at these few miles is unacceptable to me. Perhaps i am naive. I wonder how many problems with the engine others have encountered, but haven't officially reported.many i am sure.i am working full-time as well as part-time to save money for a down payment to purchase a house this year.thanks to myengine being "shot" - my husband and i will have to forgo our dream of owning a home anytime soon.hopefully we can get past this and the interest rates will stay low enough for our two year old daughter to have christmas in her own home in 2004!!!
The timing chain busted through the casing that houses it in the engine.the dealership told me that the cause could be a flaw in the chain link, and it caused severe damage to the rest of the engine, and that the engine must be replaced.estimated cost is $7000.my comments to them were, if it is a flaw in the chain, shouldn't it be covered under the warranty?they told me no.i'm trying to find out if there has been othe occurrances of this priblem, and what my recourseand next step should be.
Complete engine failure due to build up of sludge and bearing material in oil filter causing timing chain to jump and engine to fail.luckily this happened at the auto repair shop, not on the highway, as many others have experienced.have literally found hundreds of complaints on the internet relating to the chrysler 2.7l engine and its propensity to fail.our 1999 chrysler concorde has less than 40,000 miles and has always received routine maintenance.we were among the lucky ones...our engine failed while backing out of the auto shop garage...instead at 65 miles per hour going down the highway.interesting how there are no warning lights...nothing to tell you this is about to happen.
Without warning on early monday morning around 12:15 am on the new jersey turnpike between exits 1 and 2, my family was driving from mayrland back to new york, my 1999 chrysler concorde lxi madea loud banging noise under the hood along with smoke and all the lights came on the car. The engine just stopped; i swerved and pulled along the shoulder. There was oil everywhere on the ground. When oil was poured into the car, it came right out. So, my car had to be towed to brooklyn, which costs $445. Luckily my in-laws live near by so my son and wife were able to stay there for the night. My mechanic inspected the car and said that his whole fist can fit in the engine block. He said that it was caused by internal damages and a bad oil pump. My car only has 63,000 miles and is only 5 years old. Now, i need to replace my engine and the part alone will cost me $2,200.
I have a 1999 chrysler concorde that has been at the atlanta dodge dealership since march 26. The engine has sludge build-up and will need to be replaced. The air conditioner was serviced before my trip to atlanta, yet i still experienced the unit making noises the day after we arrived. (thankfully, we arrived). Within an hour of the ac unit making noises, the engine died on i-20 west. I had the car towed to the dealership. I live in florida and purchased the vehicle only 6months old ago, it has about 79,000 miles. I had 3 regular oil changes during those 6 months, and one month before my business trip, i had a diagnosis test done at goodyear because the oil light was flashing on-an-off. Goodyear also changed the oil that 3rd time. Nothing was discovered. As a single parent of 4 kids, i was trying to rebuild my credit after a series of job layoffs. I have had auto rentalsfor the 5th week now and see no end in sight. Luckily, i did purchase an extended warranty, but no one is assuming responsibility for the defect, no one-- the warranty people, thrifty dealership (where purchased) or chrysler!i am sinking further into debt. This is so unfair to the consumer. I am more than angry. I will never purchase a car again without checking ?mycarstats? (i did a very generic online search and had carfax). And will never purchase a dodge or chrysler again.i am now searching for a mechanic?s special to get around town and to work.
My 1999 chrysler concorde had a complete engine failure.it happened suddenly & without any warning lights.i was stranded on i-40 in busy traffic.the dealership says that it "spun a bearing" & showed me some metallic glitter in the oil. The car now needs a new engine at a cost of approximately. $4500.00- 5000.00.i have a useless 1999 concorde with only 90k miles & i still owe $11.000.it had regular maintenance performed. *nlm
While driving on the highway; the engine of my 1999 chrysler concorde, had a catastrophic failure.there was an incident involving the timing chain that led to a great many failures, top so being the crankshaft, as i was told by the dealership i had evaluate the problem.the engine is the 2.7l dohc v6 that comes stock with the 1999 concorde.i changed my oil regularly and never expected the motor to fail at just over 42k miles.i was 400 miles from home when this occurred, and had to wait in a shopping center for several hours until we could arrange a way home for myself, my wife, and at the time my 5 month old daughter.
My wife's 1999 chrysler concorde (2.7 motor) shut down up at wal mart.i got a call from my buddy who said he thinks she needs a battery.i go up there, buy a battery, put it in, start the car and it is knocking to high heavens.i pull the dipstick and there is a grease like substance on it.i immediately go into wal mart and buy oil.i fill the crank case up and have her start it up again.i knocks for about fifteen seconds then sounds somewhat normal.i instruct her to drive home and i will follow her.it is about four miles to home.she makes it three miles and the car just shuts off and she struggles and gets it off the road.this occurred about two hundred yards from an exit and a red light.i called a tow truck in and had it towed to the dealer where i bought it.they called the next day and we went up to see them.they never once mentioned any problems with this engine.they simply suggested we either replace the engine which is very expensive or buy a new car from them.we bought a car because she and i work and both of us work thirty plus miles from home.to boot, they sold us another concorde!!! unbelievably i found out about this widespread problem with these engines today, 8-18-08 at a dealership.they were offering us very little for a four year old concorde and stated that engine as the reasoning.i was furious.we traded it off, lost our tails-again- and moved onto a more reliable foreign named vehicle.i started surfing around to make sure that this foreign dealership was not lying about the engine and found thousands of complaints.i figured i should do my part against these robber barons and enter the arena as well.the worst part of this whole thing is we refinance our house years ago and paid off that 99 concorde to get ahead.it blows up months later and we are back to square one and actually worse off because the 04 wasn't worth anything either.
Dt: the contact owned a 1999 chrysler concorde. The engine went out with only 49,000 miles on the vehicle while driving 55 mph.this did not cause an accident, they were able to steer the vehicle to the side of the road.there were no problems with the engine prior to this.the contact purchased the vehicle from a first time owner hehad the vehicle for about six months. The contact took the vehicle to a repair shop, and they told himengine had to be replaced, and thatcar needed oil changes often. The contact insistedthat during thesix months that he owned thevehicle he kept up with the oil changes, and didnot believe that was the cause of engine failure.
I was returning home from relatives house. Engine started to rattle and the engine died on me and my son. Repair shop told me of the problem with the chrysler 2.7 liter engines blowing. Car has 95,000 miles on it.
- the contact stated that his engine seized because of a lack of oil. The contact had the car taken to a local repair shop and he was told by the mechanic that the failure was do to a clogged oil line.
Dt*:the contact stated that there was blue smoke coming out from the exhaust system and a loud ticking noiseof the pistons hitting the head of cams. While driving, the engine eventually seized and failed resulting in an non-drivable state.when the manufacturer was alerted, they determined there was no problem with the 2.7 liter engine.updated 09/11/06.
The car's engine seized up in traffic, and thankfully someone helped me get it out of rush hour atlanta traffic before there was an accident.but, it certainly could have caused one.now the motor is shot and the car is undriveable.
Dt:the caller states thatwhile driving at 50 mph engine lost power. Hewas able to get it off the road. He had it towed to a garage. They said he needed a new engine. He was told that the oil drained out of it while the vehicle was in motion and that caused the engine to fail. Caller had the vehicle towed to his home. Manufacturer has not been contacted yet.
We purchased a 1999 concorde that had 39000 miles on it in 2001.we have put 21000 miles on it since then without a problem...until last week.i was driving my 5 year old son to school and the car died on me at a stop light.i put it in neutral and started it again and was able to make it to his school, 1 1/2 miles away.after dropping him off i got it to the end of the driveway and it died again.after it cooled down it started ok and i was able to drive it home, 6 miles away.at 4 miles it stalled on me again.when i got within 1/2 mile of home it started chugging on me and when i turned the corner on my street it died again.i got it started one more time and coasted into my driveway.we could not get it to start again until it had cooled down for 2 hours.we took it to a mechanic, not a chrysler dealer, who believed it was the cam sensor.because he felt it was a possible warranty item he suggested we take it to a dealer.we did, and they said there was no warranty so we had our mechanic replace the sensor.the day after that when we would stop at a signal the oil light would flash on and off.there was oil in it since the mechanic had also just changed the oil when he had it.we took it back to the mechanic.he felt there was something wrong with the engine, but he could not identify it.he again suggested we take back to the dealer since it only had 60000 miles on it and believed it should not have this kind of a problem.we received a call from the dealer today.they informed us the car needs a new engine.
My 1999 chrysler concorde engine failed without warning on 9/21/2006.i talked with two local mechanics who both have had over 20 years in their respective businesses and both indicated the engine in my vehicle is notorious for failing without any warning and that they both have seen several of these engines and have read the problems that have been associated to this vehicle and other chrysler products with the same engine.i have contacted the chrysler consumer center and they want me to have the car towed to the closest service center so that they can diagnose why the car failed with no apparent warning.they indicated they would not offer any reimbursement of the tow bill or cost of tearing the engine down if they determined the engine was not their responsibility.i am reporting a complaint now due to fact that i have read several incidents where chrysler has not offered any help on any of the repair cost on the vehicles that apparently have a real problem with the 2.7 liter engine failure and have not recalled the vehicles or tried to fix the problem prior to engine failure.
Stepson was driving car back from toledo ohio area to canton ohio and the engine in the car jerked and then just quit. Car was towed to local dealership and informed this morning that the timing chain had broker and destroyed the engine.after researching this today i find out that there are websites referencing this and many documented cases of this catastrophic failure happening to others. I called chrysler today and i was informed that they could do nothing since the vehicle is out of warranty and that i was not the original owner so chrysler could not establish how well the vehicle was maintained.
Dt: the consumer states that onchrysler 1999 concorde the engine filled up full of sludge and the engine was destroyed. This happened in october 2003. The car was sitting in the driveway of the owner, andit has not been fixed. The cost from the dealer was $7,600.00 for a new engine, but in canada it was $3,200.00.the owner was in canada when this happened. The dealer said that the owner did poor maintenanceon the car, and that caused it to fill with sludge. The ownersend the manufacturer a letter and has not had a response. The car set in the driveway for 2 years. The owner had to tow the car back to the states.was hoping that chrysler was going to fix the car, and chrysler dealership responded they were not going to fix it.the owner said that chrysler was taking the owner to court over the payments on the car. The ownerwanted chrysler to fix the engine and then will pay them the money.
I currently purchased a 1999 concord with the 2.7 engine and had the for 3 months . I took it in for a oil change yesterday and after driving the car back to work i looked out my side view mirror and seen a huge puff of blue smoke when i took off from a stop light. I took the that night to friend who is a mechanic and he told me that the engine is done. He told me about the engine failures on these engines and so i went online to see if he was telling me the truth and i was very surprised of the amount of complaints on the engine.. The price for a rebuilt is about $3500.00 and replacement engine about $6500.00 of which i cannot afford and i still owe $4300.00 on a pile of junk that i cannot drive. Is daimler going to remedy this problem and help us out with the cost or are they sitting on there thumbs waiting for the problem to go away?
I experienced complete engine failure while traveling at 55 mph on route 295 in new jersey. First i heard a sputtering sound then the car lost power. I had to cross from the fast lane to the shoulder while losing power. I just made it to the shoulder when the car stopped for good. There was plenty of oil in the car and in fact it had just been in the shop for another costly repair of $1500 for a leaky air conditioner compressor. A bad smell had been coming into the passenger cabinwhenever i turned on the heat or air conditioner. After having the car towed i was told that by the mechanic that this car was notorious for engine failure and that he could see metallic material in the oil clearly showing the engine was blown. To repair it with a rebuilt engine it would cost $5900 plus tax.
Timing clutch broke. Ruined engine. 100,000 miles. Otherwise in perfect condition. Too expensive to replace with a new engine. Especially with the mechanical history of this specific engine. The only offer i have received to sell this vehicle is the salvage yard. $100 if i bing it to them. $50 if they come get it. This is ridiculous. All other parts in perfect condition.
Sludge build up in vehicle's engine.*mrwhen the dealer was notified about the knocking in the engine and slow acceleration they told the consumer the entire engine block would have to be replaced. The engine cost approx $5721.04 in repairs and chrysler refused to cover the cost. The consumer found that a lot of engine replacement are due to a latent defect in the car from the chrysler websites and feels that chrysler should take some responsibilities in repairing the vehicle.
My 1999 chrysler concorde with 46,000 miles on it developed sludge in the engine causing the timing chain to come off its track and subsequently damagingother parts of the engine. The dealer says the engine needs to be replaced at a cost of $8,000. When i asked what caused the sludge, the dealer told me i didn't have the oil changed enough.when i produced documents to the contrary, the dealer told me the oil used must have been bad and broke down. I find this highly unlikely. To date, i have not gotten satisfaction from the dealer or chrysler. I am aware of others with the same problem.several of these people were also told the same thing by their dealers.it seems like it's a canned routine to deflect responsibility for this problem onto someone else. I believe chrysler is aware of this problem and is not standing behind their product.can anything be done?
1999 chrysler concorde died after the motor started knocking.*mr
Problems with vehicle's heater, engine making knocking noises and slow acceleration.*mrthe heater stopped working intermittently which lead to a build up of heat in the engine cabin, which in turn lead to a build up of sludge.during acceleration, the vehicle rattled and vibrated and it did not accelerate smoothly. The consumer was informed that the entire engine block needed to be replaced, which was the cause of the problems. Also the front window and power mirror were inoperative, the dealer found a bad window motor.
The bolt that holds the fan andengine pulley came loose, causing no steering ability, almost resultingin an accident.dealer said the problem was caused by the bolt being tightened too hard.
Dt: the contact stated vehicle stalled . This has been ongoing for the past two months. After the vehicle stalled it wouldnot restart and had to betowed to a dealership. Diagnostic testing found the throttle module needed to be replaced. The module was replaced but the vehiclecontinued to stall. Updated 12/27/2005.prior to the vehicle stalling the check engine light would flash, then the vehicle would slowly lose power then shut off. The vehicle would not restart for approximately 45-50 minutes.after the vehicle was restarted it would idle low and the engine would shake; then eventually shut off again.the dealer was unable to duplicate the problem.
I was driving back from a trip from ft. Lauderdale ,fl. On labor day 9/5/05. When my 1999 chrysler concorde just stopped for no apparent reason . I just purchased this vehicle 4 months ago and i am still making payments on it. The vehicle only has 75,500 miles on it.i have put on 5,000 miles since i owned it and have changed the oil twice already.
Dt*: the contact stated while driving at 65mph the engine started knocking.the vehicle was taken to a dealership were they determined the engine was defective.there was no warning prior to the incident.the manufacturer has been alerted however no repairs have been made.
I was driving my 99 chrysler concorde home and it started knocking and then died.my engine is gone.i have 3 kids and i have no means of fixing this.and now, no way to travel.
I was told by my mechanic that i have been burning oil extemely fast. He suggested a heavier weighted oil and engine restore. He also recommended that i get a quote on having my engine rebuilt since the car probably has loose rings and valves. (i was quoted a price in the $4k-$5k range). I think chrysler should build engines that last longer than 97,000 miles.i was driving home the other day and when i went to accelerate from a stop light and the car just died. Thank fully i was on a hill & was able to coast off to the side. I mangaged to get it started again, however in a different situation it could have caused an accident. It also happened to my 16 year old son, who is no longer allowed to drive the car, since i feel it is unsafe.
Dt*:the contact stated while driving, a knocking sound was heard in the engine.the vehicle was taken to the local independent mechanic for inspection.the mechanic recommended changing the oil filter and it was replaced.however, several months later, the contact heard the knocking noise again while driving at 35 mph.the vehicle stalled and the engine would not restart.the vehicle was pushed into a yard, were it remains.updated 04/11/06.
Friday, i was driving to work, the car felt like it was going to stall out, i luckily made it to work. It made an awful sound like something broke. Later that day, i took it to a nearby garage, the mechanic said the engine had blown & his suggestion was to take it to a junk yard & hope for a couple hundred dollars, other wise, it would cost 2000.00 for a remanufactured motor & 1000.00 for labor to install the motor. He also stated that the chrysler 2.7 motor was notorious for broken timing belts & the engines locking up.
Engine failure while driving a chrysler concorde 2.7 liter engine due to sludge build-up in the engine.no warning whatsoever. *la
Driving down interstate 265 at 55 mph, engine just quit, causing a potentially deadly situation. When the engine quit, it lost power steering and brakes. Car only has 70,000 miles.air conditioning quit working in may of 2003.
I bought a 1999 concorde with a 2.7l engine at the end of march of 06. On april 3, 2006 i got an oil change and other maintenance, and the car was at approximately 127k miles. All seemed well with the car.on 7/2/06, the day before my scheduled oil change, my wife took my car to work instead of her own, as she was going to the grocery store afterwards. At about 7:07 am, i get a call from my frantic wife, and she explained to me that she was on i-96 just before the exit to i-275 in michigan going about 70 mph and the car lost power and died without warning. My first thoughtwas "are you ok?" i immediately got up and went to where she was. The car would not even turn over. I simply thought it was the alternator. However, i was infuriated when the mechanic told us that the 2.7l engines in the 1998-2001 had a design flaw, wherein an unreasonable amount of sludge build up occurs, preventing the oil from circulating through the engine, which would explain why there was very little oil on my dipstick. The mechanic couldn't give me a price on the cost of fixing the problem, mainly because out of all of the cases that he's seen with this same engine, there have been no fixes. I cannot begin to explain how inconvenient this is for me and my family. Both my wife and i are students who work. From what i've been reading, the repair/replacement of the engine can cost up to $9,000 dollars. At this point, that's more than the car is worth now, and we simply don't have the money for this type of expense.
While driving 67 mph main engine bearing failed. Dealer determined that engine must be replaced.
While driving the engine light came onand the vehicle cut off.the vehicle was towed.it was discovered that the engine was defective.( aresearch was done on the 2.7 l engine, and the failure rate was great).
Vehicle began responding to acceleration very slowly. Vehicle seized on the road in november "05". Dealership offered to replace engine for appr. $2,000- $4,000.i did not accept the offer.
Car purchased new, 3/99.jan 07, timing chain failure.while driving back from repair shop, engine bearing failed.repair shop diagnosed oil sludge failure in 2.7 liter engine. Total cost of repair and engine replacement: $ 6,092.00.
The engine seized and quit on our 1999 chrysler concord as i pulled into a local macdonalds.the vehicle was towed to our mechanic and we were informed that the engine needed to be replaced.thankfully, this did not happen the day before while i was in 65 mile an hour traffic.we had been experiencing oil burning for the previous two months.but the car seemed to be running fine.i had just had the oil changed 12 days prior to this incident.because our mechanic is having trouble locating a used engine, i began searching and found that we are not the only consumers of this product to have this happen to.
Engine started making loud knocking noise.had the car towed to chrysler.chrysler reports that the timing chain came loose and caused severe damage to the water pump and engine and the timing chain, water pump and engine need to be replaced.they report that there were no oil leaks and filter and plug were in place and dealer could not explain cause. I have spoken to chrysler corp. And the dealership.chrysler agreed to help with repair until they found out the engine was damaged and needed to be replaced. The repair will be 6,700 dollars.i see there are other reports of this same problem.would like to know if others received any financial assistance from chrysler and what my next steps should be.
Dt*:the contact stated while driving at 30mph the vehicle stalled without warning.the vehicle was pulled over, restarted, and then driven home.the vehicle was towed to the dealership and it was determined the oil did not distribute properly in the engine causing a piston rod bearing to burn.the vehicle needs a new engine.
I purchased a 1999 chrysler concorde and after getting on the highway with the car to take it to my local dodge/chrysler autoshop (not even 3 minutes), the car failed and stalled on a major highway. I was able to pull the car onto the side and after calling several people and waiting for over an hour, i was told that the engine was probably locked and had it towed to a chrysler autoshop in the vicinity of where i stalled. I wasn't even able to make it to the next exit on the highway once i merged on the highway , approximately 1 mile from where i purchased it, the car stalled, no warning just stopped with 18 wheelers and everything behind me and almost crashing into me.
My engine in my 1999 chrysler concorde completely failed with no warning while driving under normal conditions. I kept my car in the shop practicing all periodic maintenance procedures.
Premature engine failure of the 2.7 liter engine found in the chrysler concorde.
1999 chrysler concorde engine failure at 90000 whille wife and children in traffic engine failure due slug build up. Mechanic said it would cost $4600.00 to replace engine still owe 11000 on it, and cant afford to repair. Mechanic said slug build up is due to oil pump design also have ac problemand have had radiator fan failure twice , speed sensor failure, broken window clips,brake shimmy , broken recliner seat bolts
I suffered major loss in valu,e and my husband was in a very dangerous situation due to the failure of the 1999 concord engine.y 1999 chrysler concord had under 57,000 miles, and was diagnosed as needing a replacement engine due to oil sludge. Despite providing chrysler will oil change records showing the timeliness of maintenance to my engine, they claimed no responsibility. I was told i needed to replace my engine and that it would cost approximately $9000!!!my husband was driving the vehicle on the highway at a speed of approximately 65 mph when the engine started smoking, bogged down and started to "die". In order to avoid a potential accident, he had to immediately drive over the shoulder and through the grass so he could safely get the car off the highway and onto the side of the feeder road.the cost to replace or repair the engine was much more than the blue book value of the vehicle. In fact, the blue book value was deflated at least in part to failing engines of the concord. I had little choice but to sell my car "as is" for a mere $1000!!! my car was in very good condition prior the engine failure and i believe the blue book value was approximately $7000
I was stopped at a stop sign and pushed the gas pedal to proceed. When the gas pedal was pushed my car began to make loud screeching noises and lost power in the middle of an intersection.
My 1999 chrysler concord engine seize after an oil charge. I got the oil change on saturday and monday my car engine was knocking and by the end of the week the car was parked in the drive way. I researched the web for information on this engine and pretty much everybody that has this engine will have to use out of pocket money to fix the dame thing that cost twice its market value to fix.
Dt:the consumer owns a 1999 chrysler concorde. While driving, the vehicle began to make a noise and the engine just shut off. Prior to this incident the blower worked but there was no heat. The mechanic said the engine was bad and this was a bad year for these engines.
Without any warning, my chrylser concorde 2.7l engine suffered a complete failure.repair costs are near $5000 and upon research, i found this to be a common problem on chrysler 2.7l engines from 1998 to 2000.chrysler denies any allegations of the engine being faulty and that they are failing due to improper maintenance.the most that engine ever went between oil and filter changes was 4200 miles and that was a one time occurrence.the rest of the changes were done at or before 3000 miles.chryslers recommendation under normal conditions is 6500 miles.
While driving vehiclemade a loud rattling noise.consumer pulled over,stopped the vehicle, and the enginefailed. Took the vehicle to the chrysler dealer. Found that they have been having this problem with the engine on thisparticular vehicle.
The contact owns a 1999 chrysler concorde.the contact stated that the engine stalled while driving.the failure occurred without warning.the check engine light illuminated.a local mechanic diagnosed the vehicle as needing a new engine.the engine has not been replaced.the current mileage is 126,000 and the failure mileage was unknown.
While driving at 50 mph engine failed without warning. The vehicle was towed to the dealer.the dealer replaced a total of 5 computers but the vehicle continued to stall.*nlm
1999 chrysler concorde 2.7 litre engine failed. Suddenly just stopped. Had a recurring problem where the engine would shut off and the steering wheel would lock up, whether i was driving straight or making a turn. Im one of many thousands of chrysler victims.
The contact owns a 1999 chrysler concorde.while driving 35 mph, the vehicle came to a complete stop without warning.the vehicle was towed to the dealer and they stated that the timing chain tensioner failed.the timing chain kit was replaced.when the oil pan was removed to make the repair, there was a lot of oil sludge build up.the current and failure mileages were 118,000.updated 3/11/08 updated 03/11/08
Have had trouble with the 2.7 liter engine in my 99 concorde, sludging, excessive oil consumption, coolant loss and premature engine failure. Despite regular oil changes the engine would sludge up and cause tapping noises. Had the problem dealt with once in 2003 at area dealership under the extended warranty, at that time the dealer tried to charge me for the repairs stating it waslack of maintenance that caused the problem. Eventually they assumed responsibility and repaired the vehicle. Since then i have changed oil regularly as i had before and the problem of oil consumption persisted. I just added oil and coolant as needed between regular changes at the rate of approximately 2 quarts oil per month and 1 gallon of coolant per month. While driving home from work the engine very abruptly started to clack so i pulled over and had it towed to my regular repair facility, where i was informed the engine was no longer usable due to oil sludging and lack of oil circulation. Contacted chrysler corp. They instructed me to take it to the dealer that originally repaired it and they would make a determination after the dealer inspected it . This is the same dealer that tried to blame me for the original problem. Have researched this problem and have discovered this to be a rampant problem with this engine and that chrysler denies any responsibility. There are numerous web sites detailing the problems consumers are having with this engine and their stymied efforts to have chrysler deal with them fairly.when i called nhtsa they stated they had no complaints, i hope this one will prompt a further investigation.
While driving vehicle stalled.consumerwas unable to restart the vehicle, but managed to pull over, and hadvehicle towed.dealership mechanic had been notified, but was unable to resolve the problem.
Engine shuts down after driving more than 90 miles with out stopping.
Dt*:the contact stated while driving at speeds above 45 mph, the check engine light illuminated.the rpm's then went to zero and the vehicle stalled.this has occurred 5 times in the past year.the vehicle was pulled over and started after waiting at least 2 hours.the computer does not store any codes and the dealership is unable to determine a problem.the fuel filter and battery have been replaced, but this has not corrected the problem.
The contact owns a 1999 chrysler concorde.while driving 45 mph, the vehicle shut off and stopped in the middle of the freeway.the contact was able to maintain control of the vehicle, although the brakes and power steering failed.someone had to assist her with steering the vehicle to the side of the road.the police was called and the vehicle was towed to the auto repair shop.there had not been any engine failure prior to this incident.the auto shop stated that engine sludge coated the engine.it would cost $5,000 to replace the engine.the failure mileage was 60,000. Updated 2/23/09 the passenger seat belt was difficult to unfasten and the rear passenger door had to be opened from the outside. Updated 02/26/09.
I'm filing a complaint about my 1999 chrysler concorde.my car was in the shop for other repairs and when i picked the car up and drove it home and begin to give me problems so i turned around to drive the car back to the repair shop and it cut off right in the middle of the intersection.i had it towed to the shop and they called me and said the engine went out.i could not understand why and howdid this happen cause this was without warning and i only had the car for a short period of time and i kept the maintenance up on it.the repair shop said that this would be a hassle going thru the extended warranty company cause they would not want to replace the engine so i wanted a second opinion, i had it towed to another shop and they said the same thing, that this was a 2.7 engine and it's expensive and it's not worth anything and the warranty company will probably not cover much of anything.i feel that since this engine is known to have engine failure problems, something should be done about this cause it's not safe for an engine to go out without any forewarning and it's not affordable at all..please acknowledge this immediately.
Consumer stated that vehicle would not start.hetookvehicle to dealer, and was told that engine malfunctioned.it would cost consumer $8000.00 to get it repaired.consumer insisted that the motor should not havefailed at 96000 miles.
6 times my 1999 chysler concorde 2.7 motor was taken to dealership for problems with the motion sensor/cause motor to uphift or downshift at random or get stuck in gear...last week a loud rattling in the motor 74000 miles...engine replacement ...$3,000
While driving vehicle stallled. Driver was unable to restart vehicle, andha dit towed to the dealer for inspection. Mechanicdetermined that the engine needed to be replaced due to sludge build up.
Fuel pumpfailed/timing belt broke, and the piston went through the engine.as a result, the vehicle stalled while driving at a low speed. Dealership was unable to replace the engine due to a back order because this was a common problem.
While driving, the vehicle completely shut down. The consumer was told there was oil sludge build-up in the engine. Please provide any further information.
Engine seized while driving, causing vehicle to losepower.
2.7 eng. Failure chrysler concorde 1999 ,well maintained( it just stoped).
The engine in our 1999 chrysler concord blew at only 38000 miles, it was the famous flawed 2.7, chrysler refused to replace the engine - told us we must not have changed the oil often enough!my husband is a district supervisor for a oil change chain here in michigan, the oil was changed religiously with synthetic blend, an oil far superior to the basic factory recommendations.we replaced the engine ourselves at our own expense with a3.2at a cost of $3000.chrysler refuses to admit any defects in their 2.7 motors, yet other companies whom used this engine have voluntarily recalled it!
While driving between 35-45 mph, the vehicle stalled without warning. When this occurred, the vehicle lost all power. Please provide any additional details.
Oil sludge in low mileage engine.
(1) heard persistent knocking/pinging sound that was growing louder(2) took to mechanic who diagnosed imminent engine failure - cracked rod(3) replaced engine, found cracked rod and engine loaded down with sludge.
Consumer statedwhile driving heard someengine noise. Pulled off the road,and engine diedcompletely. Dealer notified.
While on my way home from work at 2 am, i started to hear a loud "clunking" noise from the engine compartment on my 1999 chrysler concorde.i was on the highway, and the car rapidly decelerated to 25 mph.i managed to pull off into a rest stop, but didn't even make it into a parking spot before the engine quit.i found it amazing, since we just got the car back after $1600.00 in repairs four months ago.now, my mechanic is telling me that chrysler only made these engines to last for up to 5 years at the most, and he's not surprised.well, i am.a vehicle should last more than 5 years.now the only option the mechanic tells me i have is to purchase a whole new engine and replace the old one.
Sludge build up in engine has caused thru no error on my end a blown engine, with no warning. I need a new motor even after all the money i've put into it with sensors in the tranny, new window motor, rod knocking...and i changed oil in the car every 3,000 miles using the oil that chrysler recommends. There is so much sludge build up on this 2.7 engine that if it were a human artery the patient would have died too...this is an ongoing problem with these motors and no one will do anything to help us get it fixed, unless we have an extra $7,000.00 sitting around
1999 chrysler concord with engine problems customer wants the blue book value for the car from the dealership**ccthe consumer stated the engine had to rebuilt due to sludge build-up. A mechanic informed the consumer, the vehicle was built with a faulty oil pump, which was too small for the engine. The front seat belt retractor were replaced.
Door's automatic locking mechanism/ power windowsfailed, and engine was making loud noise . Also,and front alignment malfunctioned twice. Dealer notified.
The contact owns a 1999 chrysler concorde.while driving approximately 30 mph on normal road conditions, the contact heard a loud noise coming from the engine.the vehicle stalled intermittently and the check oil warning indicator illuminated on the instrument panel.the warning indicator remained lit until the engine was turned off.the vehicle was driven to the contact's residence and inspected by an independent mechanic.the technician stated that oil sludge caused the engine failure and it was recommended that the engine be replaced.the vehicle is currently inoperable and has not been repaired. Updated 3/5/09 updated 03/10/09.
Engine began to make noise. Shut down & towed to shop. During diagnosis noise got progressively louder & timing chain jumped. Engine needs to be replaced. Car has 59,000 miles & was always well maintained. My research on the internet has turned up many chrysler & dodge 2.7 litre engines from 1998 to 2002 with the same low mileage failures. Chrysler corp. Blames it on lack of maintenance, but that's hard to believe with so many identical complaints.
Consumer complained aboutengine failure on 2 separate occasions which resulted in vehicle stalling. This occurred because of oil sludge build up in the engine, and dealer replaced the engine.
Dt*: the contact stated while driving 20 mph the engine failed without warning.the vehicle was towed to the local dealership.the dealership determined the engine needed to be replaced.the manufacturer was alerted.
My 1999 chrysler concorde was maintained per the owners manual instructions yet the engine failed at 55,700 miles.please advise why chrysler has provided 50% of the cost to replace chrysler engines for other customer yet chrysler has not offered any financial help to replace the engine in my chrysler vehicle?
Ii bought a 1999 chrysler concorde in late october of 2003.it had low miles (35,000) and the dealership (a chevy dealership) gave me a 90 day or 3,000 mile warranty.i am faithful about taking care of my care so imagine my surprise when the engine light came on and as i was driving it to the chrysler dealership, it died.i had it towed there and they called me the next day and told me that the timing chain had gone out and that i would need to have it replaced.i gave them the go-ahead.but within hours, they called me back and asked if i had ever changed the oil in my car?i told them that i had within the last 1,000 miles.i had just purchased the car, and it had come with a 120 point inspection (including an oil change).the chrysler dealership said it was the worst case of sludge he had ever seen in his 17 years of working as a mechanic!i was stunned.i had just purchased this car!he told me i should have it returned to the chevy dealership where i purchased it, and demand that they repair it.well two days later, i have my car towed down the road to the chevy dealer and i call them to tell them the bad news.they inform me that they can fix it at the cost of $7300 for a new engine, $6300 for a rebuilt one or $5700 for a used one of 30,000 miles!i financed the car at a 9% interest rate on $7,000.if i pay for a new engine, i would be paying for this car 2 1/2 times over!i told them that it was unacceptable.they then told me the name of the local chrysler representative here in the greater cincinnati area.i have a phone call in to mr. Greg pritz but i have yet to hear back from him.do you offer advice or suggestions.durell - butch - hamm.
The number 4 cylinder failed causing the vehicle to loose all power while driving.nlm
Consumer states that while driving heard a banging noise from the front of vehicle, check engine light came on.had vehicle serviced, the engine had blown.*mr
Engine started making loud knocking noise.pulled off of highway at next exit, drove into parking lot and stopped vehicle.had vehicle towed to dealer and was informed that the engine needed replacement due to oil starvation.dealer could not explain cause of starvation, as oil levels were normal, oil pump was functioning and oil was clean.dealer could also not explain lack of telltale warning lights for oil pressure, etc. Prior to event occurring.estimated cost of repair $5,000.this is apparently not an uncommon problem.have reported to chrysler although car no longer under warranty.am awaiting response.
I saw a light bluish smoke come from my tailpipe once and then later in my drive the engine started making funny noises and then all of the sudden my car seized up and shut off.it restarted but then shut down again almost immediately.my engine is completely shot says my mechanic with me getting almost no compression.i was not overdue on my oil change and i had just refilled my oil 2 days previous.
My car a 1999 chysler concord has approximately 70,000 miles on it. It has used oil ever since 30,000 miles mark i'm talking 3 quarts per oil change. I see in chyslers memo to dealers this is acceptable it should use 1 qt. Per 750 miles. At that rate it's empty on oil by oil change time at 3000 miles. Now i'm driving and a rod bearing goes out. Again another well known and documented problem with the 2.7 l engine. Here i sit making $400.00 payments on a car i can't afford to fix ($4000.00) to replace engine. Please help us to get a much needed recall!! thank you. *ph
Contact states: contact maintains car regularly, without any warning the car made a clicking sound and stopped. Will not start and had to have tit owed. Now finding out that the timing belt broke, and there was so much engine damage that a new engine is required due to damage of sludge build up.
Dt: the contact owns a 1999 chrysler concorde. The timing chain failed while driving on august 16, 2005 , causing the engine to stall. The dealership stated thatthe contact could haveengine rebuilt which would cost$7000-8000 dollars or they could do it for $2500. The dealershipcould not givethe contactany type of explanation as to why the timing chain failed. The current mileage on vehicle is64, 200.
Dt:contact stated the timing chain broke. The dealer could not give an estimate over the phone of how much it would cost to repair thevehicle. The manufacturer has not been contacted.
Dt:th econsumer complained about anengine problem. The first time he stopped at a traffic light and when he tried to pull out the engine stalled.he was able to get it to start it back, but it made a lot of noise.the consumer took vehicle to a mechanic who told him that there was a problem with the timing chain.and they told him that the engine needed to be replaced.he had the engine replaced.recently, the problem recurredthe consumertook vehicle to a mechanic again.they told him that if they fixed the timing chain that it might help or there may be more problems.he has not had this fixed as of yet.
Fuel pumpfailed/timing belt broke, and the piston went through the engine.as a result, the vehicle stalled while driving at a low speed. Dealership was unable to replace the engine due to a back order because this was a common problem.
1) driving 1999 chrysler concorde when weird noises started.pulled off the road.stuck with my (2) children in a hot car until tow truck came.2) car would not restart.called chrysler dealer.they said the tensioner for the timing belt was broke.we fixed that for over $400.00.then they ran a compression check.no compression.they said the valves in the engine were probably bent.looking at $2,500.00 or more to fix or a re-built engine for $7,000.00.3) my husband had the car towed back home.we are tearing it apart ourselves. (cant afford chrysler to do it).the valves are bent.we are taking the heads to a local machine shop to put new valves in.
While making a left hand turn vehicle stalled. As a result, the timing chain broke, and sludge built up.
Dt*: the contact stated while traveling 70 mph, the vehicle stalled without warning.the vehicle would not restart and was towed to the dealership, who determined the timing chain broke and bent the valves.a new timing kit and heads needed to be installed.
Blinking engine light, smoke from exhaust, all mechanics state that i need a new engine,but no shaking, rides smooth, unsure why it smokes, i have used sealant, check gaskets and no change.. I bought the car in 2008 from a private owner and it passed smog, shortly after the engine light came on and it went downhill from therediagnosed engine, repaired oil pan.
Air conditioner has to be recharged periodically due to a leak.
The contact owns a 1999 chrysler concorde.the contact stated that the abs light illuminated and she heard a noise in the engine compartment.the mechanic stated that the pump motor circuit for the abs failed and caused the light to illuminate.the approximate cost to repair the vehicle was between $1,500 to $2,000.the front rotors were replaced in april of 2006 and in september of 2007.in january of 2007, the front driver side bearing was replaced.the mechanic stated that the failure was due to poor design and cheap parts.the air conditioner also began to leak.the mechanic stated that there was a hole in the suction line because of the design, and it rusted and rubbed through another part of the vehicle.the air conditioning suction line was replaced in september of 2007.the leak could have potentially caused a fire.the mechanic stated that the power steering kit needed to be replaced.the vehicle could easily rust into the frame and condensation could collect.the vehicle is currently hesitating and surging.the current mileage was 78,100 and failure mileage was 78,000.updated 03-04-08 the leak of the power steering hose could cause a fire. Updated
I have a 1999 chrysler concorde that has been at the atlanta dodge dealership since march 26. The engine has sludge build-up and will need to be replaced. The air conditioner was serviced before my trip to atlanta, yet i still experienced the unit making noises the day after we arrived. (thankfully, we arrived). Within an hour of the ac unit making noises, the engine died on i-20 west. I had the car towed to the dealership. I live in florida and purchased the vehicle only 6months old ago, it has about 79,000 miles. I had 3 regular oil changes during those 6 months, and one month before my business trip, i had a diagnosis test done at goodyear because the oil light was flashing on-an-off. Goodyear also changed the oil that 3rd time. Nothing was discovered. As a single parent of 4 kids, i was trying to rebuild my credit after a series of job layoffs. I have had auto rentalsfor the 5th week now and see no end in sight. Luckily, i did purchase an extended warranty, but no one is assuming responsibility for the defect, no one-- the warranty people, thrifty dealership (where purchased) or chrysler!i am sinking further into debt. This is so unfair to the consumer. I am more than angry. I will never purchase a car again without checking ?mycarstats? (i did a very generic online search and had carfax). And will never purchase a dodge or chrysler again.i am now searching for a mechanic?s special to get around town and to work.
Erratic functioning of air conditioner in very warm climate. Dealer unable to repair in timely manner. Also dealer not willing to hand out paperwork upon vehicle taken in for repair. As well dealer did not offer alternate transportation to me the consumer!
A/c heater problems since car was new, control head replaced three times. Entire a/c system replaced by reputable independant auto/truck a/c company @ 60k miles. This independant company indicates that it's widely known in the industry that chrysler a/c systems are expected to fail @ 60k miles, and we can reasonably expect newly installed system to perform for 60k miles. We've spent over $2000 on the a/c,last month replaced with control head #3 @ chrysler dealer $300.00, still not working right... Clear that chrysler really has no clue... System is clearly defective. Problem very widespread, ask anyone. Most folks just give up, junk or trade.
Whenever i turned on ac,car smells like a barn, house of mold. On two occasion dealer spray the ac inlet but problem continues, i believe this is significant health problem my wife and 25 months old daugther unable to get in my car. Ts
Driving down interstate 265 at 55 mph, engine just quit, causing a potentially deadly situation. When the engine quit, it lost power steering and brakes. Car only has 70,000 miles.air conditioning quit working in may of 2003.
Air conditioning/heating unit does not cool or heat properly. Has been investigated regularly without chrysler dealer "finding" anything.on particular date below it was a very cold morning, used heat and drove 3 kids 20 miles. Stopped for half hour, got back in car and car sounds like a diesel engine - rough and loud. I was alone with the 3 kids.asked a couple of men to listen, they thought cylinder(s) were gone as noise lowered when engine revved. (by the way, this car has had 2 transmissions already, with 73,000 miles). Limped home scared to death on interstate highway with the 3 kids.stopped at service station, told not to drive as engine was failing.called aaa and they came and towed to chrysler dealer. Dealer was unable to replicate the diesel sound and "found nothing wrong." today is nov 24th 2003 and this morning the same sound is back in my engine. The heat only works when i am moving, not at idle, and leaves a very odd smell in the car if the car is left idling with the heat on.i have a 5 month old, a 5 year old and an 8 year old, i am getting very frightened to drive this car with them in it anymore. I did an online search and found that this ac/heat problem is prevalent in this model (chrysler concorde 1999) and can create sludge in the engine that causes sudden engine failure.i want this fixed and i want you to get after chrysler about this! *la
Air conditioning continually goes out. As car has expired warranty, chrysler says they have no obligation to repair. I disagree. I believe that chrysler, and in my particular situation, has a faulty a/c system.
While replacing the battery the jack broke andvehicle fell to the groundand consumer was under the vehicle. Consumer sustained major injuries and was transported to a hospital. Consumer will contact the manufacturer in the near future.
I was parking on a parking lot and lot had a structured small post on the driver side; due to visibility that the vehicle lamp omitted to light properly, i damaged the front right corner bumper.i have noticed thatthe corner lamp assemblies have a problem with the reflectors.this lamp doesn't have the required amber side reflectors don't work well cause i can barely see (not like my other cars).there is a recall set already for part number cs114-u0bj2 which is a combination corner and lamp assembly for this vehicle.i am asked to contact sabersport who is doing the recall (recall id#09e012000 exterior lighting); however, their number is disconnected and their online contact number is a wrong number.at this point, i don't think its right that i have to pay for these repairs.even upon repairs,i need the vehicle with correct lamp assembly so it doesn't happen again.next time, could be a worse accident.[xxx]information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6).
Dt*:the consumer stated the brake pedal must be pressed down too far to stop the vehicle.the vehicle has been to the dealership and multiple independent repair shops, but there was no repair available.the manufacturer determined this is how the vehicle was made.also, the headlight gasket continuously falls out but no repair is available. Updated 03/28/06.
The headlights on my 1999 chrysler concord have become foggy and discolored to the point that the lights appear dim in the evening.this appears to be somewhat hazardous as visibility in night driving is necessary.chrysler says that thereis no warranty for the headlights.cost to replace them is probably in the neighborhood of $700.i have heard this is a common problem.i have had many problems with this vehicle and i realize i bought it used but i feel that these headlights were defective from the beginning.
Subj auto 1999 chrysler concordeplastic headlight lens on both sides have degraded are becoming opaque, thereby reducing the effectiveness of the lights at night.
Dt*:the contact stated the seals for the headlights cracked and the headlights are on the verge of detaching.the dealership determined the entire headlight assembly must be replaced.
The contact owns a 1999 chrysler concorde.while driving 35 mph, the vehicle hesitated, vibrated, and then shut off.the contact was able to restart the vehicle and drove to a mechanic.the mechanic stated that the engine caused the failure.as of december 10, 2007, the mechanic had not repaired the vehicle.the current and failure mileages were 83,000.updated 3/11/08 the consumer stated while driving the headlights blink within the first 5-10mins and the dealer will not fix the defect which the consumer was informed the computer was the problem. Updated 03/11/08
The headlights on my 1999 chrysler concord have become foggy and discolored to the point that the lights appear dim in the evening.this appears to be somewhat hazardous as visibility in night driving is necessary.chrysler says that thereis no warranty for the headlights.cost to replace them is probably in the neighborhood of $700.i have heard this is a common problem.i have had many problems with this vehicle and i realize i bought it used but i feel that these headlights were defective from the beginning.
Dt: the headlights havea coating that gradually isgetting worse. It's hard plastic headlight that the sun hits,causing it to turnyellow and to have athick tint of film on it. This can be hazardous at night.
Problems with speed sensors on chrysler concorde.*mrthe consumer was very concerned about the speed sensor problem, and feels that it should be addressed.two incidents occurred with in a year of purchasing the vehicle. Please respond promptly in resolving matters. The windowmotor failed and the headlight devices fell off.
Dt: the headlights havea coating that gradually isgetting worse. It's hard plastic headlight that the sun hits,causing it to turnyellow and to have athick tint of film on it. This can be hazardous at night.
Dt*: the contact stated the driver's seat was fractured.a nhtsa recall, # 03v035000 was performed on the vehicle concerning, seats: front assembly: recliner on 9-23-03 however, the recall did not remedy the problem.the dealership would not offer a second repair under the recall.08/29/06the right rear stop lamp blub had to be replaced and both front wiper blades were replaced.
The contact owns a 1999 chrysler concorde. The contact stated while driving at an undisclosed speed, there was a gasoline odor detected while the vehicle was parked. There was no visible fuel leak on the ground when the contact inspected the vehicle. The dealer was informed of the failure but informed the contact that the vehicle needed to be diagnosed. The vehicle was not diagnosed nor repaired. The manufacturer was made aware of the failure and informed the contact that the vin was not under recall. The approximate failure mileage was 248,000.
While driving down i-45 in conroe, texas, my engine sputtered, jerked, and died.as you know when you lose engine power, your steering wheel becomes locked up and its almost impossible to control the car.it has died on me before but on back roads almost home or at an intersection.i didn't realize the seriousness of it until it happened on the freeway and there are people coming up on me doing 70-80 mph and i am quickly coming to a dead stop.
Fuel pumpfailed/timing belt broke, and the piston went through the engine.as a result, the vehicle stalled while driving at a low speed. Dealership was unable to replace the engine due to a back order because this was a common problem.
A heavy odor of gascoming into the vehicle.vehicle was taken to thedealer, andthey didn't seem to think that it was important toreport this to nhts .the fuel rail was replaced..et.
A heavy odor of gascoming into the vehicle.vehicle was taken to thedealer, andthey didn't seem to think that it was important toreport this to nhts .the fuel rail was replaced..et.
There is a fuel leak at the connection of fuel rail and fuel line 2.7l engine vehicle was staionary cold or hot motor 6/ 2/ 2017 . There was a recall early 2000 year for same problems .
The interior lights stayed on, even after the vehicle was turned off, which drained the battery.consumer had to remove the fuse as a temporary fix for this problem. The cause of the failure was undetermined.
The contact owns a 1999 chrysler concorde. The contact stated that the passenger and driver side door handle broke; as a result she was unable to unlock the doors in order to exit the vehicle. The contact alsomentioned that the automatic locks and interior lights would turn on and off. The vehicle was taken to a local mechanic who decided to glue the handle back on as a temporary remedy. The remedy failed to repaired the problem since the handle came off completely. The manufacturer was made aware of the failure but did not offer any assistance since the vehicle was not included in any recalls. The vehicle was not repaired. The failure mileage was unknown and the current mileage was 85,000.
When i was in my car one day, i parked and tried to get out. The door stuck and i think this was because the rubber stuck to the door.. It took me fifteen minute to get out of my car. I had to lift up the bottom of the now detached inside plastic frame in order to get out of my car. In about a year< the same thing happened to the passenger door> my daughter tried to get out of the vehicle and the door got stuck... She pushed the door and the plastic inside frame detached from the door the same way the driver's side did.now we must lift that door too.. This happens almost all of the time and if there is an emergency and we have to get out, this is a huge concern. If there was a fire or crash..i met someone with the exact year and model care and they have the same problem... Please help me!
Brakes continuously lock, which causestires to lock and the car skids and pitches forward.our door locks are broken and the bottom portion of the back seat is coming out from the floor.when we purchased the car, we asked the salesperson (tim white) if the car was in good condition and if this was a rental car.he said"it had one owner."when i repeated this to the manager last week, he said it did.he stated that the owner was the rental company in florida.then i pointed out to the manager that one owner did not mean one driver. With it being a rental car it has had many drivers some not so careful as others. If i had been inforrmed of the cars true history and condition, i would never have purchased this automobile.( dot number:)
Door's automatic locking mechanism/ power windowsfailed, and engine was making loud noise . Also,and front alignment malfunctioned twice. Dealer notified.
This is the message that i sent to chrysler corporation on 4/8/2003.i am having a problem with the items below.the car is a 1999 chrysler concorde lxi.i purchased it used sept. 2002.i currently have 46201 miles on the car and by looking at the information on you website see that i am not the only individual to have these problems.my rear driver's side window is not working.it worked when i purchased the car, but now it doesn't even go down.i am having it replaced, but am not happy that a car only 3 years of age has such a problem.i have already done my research and have realized that i have purchased a car with numerous problems.also, the front passenger door lock mechanism (actuator) also has to be replaced.it is currently making a very loud pitched noise when activating the locking feature.the unlock doesn't make the noise.i would appreciate a response about this information.i will also be contacting the nhtsa about these issues so they are aware of them.when at the dealer today, 4/8/2003, the service person said that the door lock mechanism has been a consistent problem.i really don't think that i will be purchasing or persuading an individual to purchase a chrysler product.sincerely, [xxx]. *nlminformation redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6).
Passenger door lock stopped working. Only able to open the door mannually inside by flicking the lock up or with my key outside by unlocking it.
The contact owns a 1999 chrysler concorde.while driving 45 mph, the vehicle shut off and stopped in the middle of the freeway.the contact was able to maintain control of the vehicle, although the brakes and power steering failed.someone had to assist her with steering the vehicle to the side of the road.the police was called and the vehicle was towed to the auto repair shop.there had not been any engine failure prior to this incident.the auto shop stated that engine sludge coated the engine.it would cost $5,000 to replace the engine.the failure mileage was 60,000. Updated 2/23/09 the passenger seat belt was difficult to unfasten and the rear passenger door had to be opened from the outside. Updated 02/26/09.
The plastic trim molding, that is between the glass and the hood, is rattling severely.consumer feels that this molding may fly off at high speeds. Also,consumer hasa problem with the trunk hydraulic lifter failing to keep the trunk propped up safely.
My son, a teenager and excellent driver, was driving through heavy snow.car was in motion with minimal spinning of wheels.smoke entered passenger compartment through vents.he turned off car and popped hood, which did not release.saw flame in engine compartment through slits near wipers.still could not release hood by hand at front of vehicle.used snow to attempt to extinguish fire and was joined by person who completely dischargedsmall extinguisher.asked that fire department (fd) be called, and fd extinguished fire.car was a total loss.contacted daimler chrysler same date and have not heard result of investigation.i understand there's no relevant recall, but car was in excellent working condition.i loved it and had no complaints.now am forced to replace vehicle.insurance has completely satisfied lease obligation, but i am disadvantaged as i must replace vehicle and i feel that the manufacturer must be at fault.can you provide any info or assistance?
Plastic trim molding, that is between the glass and the hood, is rattling severely. Consumer feels that this molding may fly off at high speeds. Also, trunk lid springs failed to keep the trunk propped up safely.
Air conditioning continually goes out. As car has expired warranty, chrysler says they have no obligation to repair. I disagree. I believe that chrysler, and in my particular situation, has a faulty a/c system.
I took the vehicle to my dealer in richmond,va.to have the transmission fluid changed.three hundred miles later the transmission locked up.according to the present dealer the transmission is totaled and must be replaced at $2700.00.i contacted the chrysler corp.and they refuse to acknowledge a problem and will not participate in replacement.
Automatic transmission failed. Yh
Clamps on transmission hose that connects to the radiator is leaking transmission fluid onto the front brakes discs.consumer found out about the problem when trying to putvehicle in reverse, and the vehicle would not move . Contacted dealer, and dealer stated that they were aware ofproblem, and thatclamps have been redesigned fornewer models. But, there was nothing that they could do.please give any further details.
I own a 1999 chrysler concorde lxi.i have had numerous problems with this car since i have owned it.lot of little things. Window motors, cooling fan, transmission overspeed sensor, and the list goes on.now the air conditioner is going out, having to service it about every 2 months.why i am writing though is the steering.seems like it is going bad.i feel this is a safety issue and read many complaints on your web site concerning this.why hasn't a recall been ordered for this and the speed up issue?
While slowing to a stop the transmission makes noise (clunks).nlm
Dt:1999 chrysler concord.the consumer stateda sensor chip malfunctioned inthe transmission.this made the vehicle shift through the gears.the problem has been repaired.this started approximately 2 weeks ago onseptember 7, 2005.
Transmission failure after only 57,801 miles.
While driving 60-65 mph, transmission would not shift, then, there was a loud noise, and vehicle started to slowdown. Consumer was able to coast to shoulder. Towed to independent shop, transmission had to be replaced. 2 days prior, vehicle had been taken to dealer for problems with transmission, when in park it would roll, and when in drive it felt like it was in neutral. Dealer stated there was nothing wrong with transmission and it was safe to drive.
The car i was driving was a 1999 chrysler concord that had been in excellent driving up until the time of the incident.just three days earlier the automobile was serviced at a chrysler dealership service center for an oil and oil filter change. I inquired at the pick up event if the brakes were okay and it was reported to me that the were fine and that everything with this automobile was fine.on sunday, september 3, 2006, i started this automobile in my garage to go to church. After putting my seat belt on, i usually inch myself out of my garage very, very slowly. However, this time after adjusting the transmission lever from park to drive my automobile took off so fast i could not control it at all. I hit the breaks as hard as i could but my automobile would not slow down at all. Not only that, i could control the steering of my automobile at all. I live near the pacific ocean and there is a drainage ditch right across the street where i live that connects with the ocean. There is a chain-linked wire fence that separates the street from the drainage ditch.my automobile raced out of my garage, down my driveway, went across the street and hit the curb across the street where it force my automobile to swerve across the adjoining street to break through the chain-linked fence where it went down a concrete embankment for an approximate 20-foot drop until it completely stopped in the water. The car then began filling up with water until it became completely submerged. Fortunately, a neighbor happened to be looking out of his second story window of his house when this incident occurred and immediately called 911. Emergency personnel arrived promptly to save my life by pulling me out of the window of my automobile. I was taken by paramedic personal by ambulance to the emergency room of a nearby hospital were it was determined i had not sustained any immediate injuries at all.the automobile was later determined to be a totaled wreck.
Sensor on automatic transmission failed for second time.in each case, while at speeds in excess of 40 mph, car downshifted hard and in most recent episode, stalled in traffic.first replacement of sensor covered under warranty on 9/5/00 at 23,885 miles.part replaced was 4800878.second incident took place on 1/25/02 at 45,910 miles.part replaced shown as 4800879 but service manager at dealership (eddie accardi, pompano beach, fl) indicated he replaced both an input and output sensors (this is not reflected on my invoice however).in each case, failure came on with out any warning.car is driven by my wife (56 years old) who is an adequate operator.she says in most recent incident, when car downshifted hard, it also stalled in traffic.she had some difficulty restarting the engine, then pulled the car to the side of the road and called me.i drove the vehicle to the dealership at about 30 mph and 4000 rpm.check engine light came on, speedometer did not operate.would not shift to next higher gear.vehicle stalled each time i stopped for traffic light. Attempts to discuss this with chrysler customer service and service manger at accardi did not receive what i consider, a serious concern for the potential gravity of such a loss of power on the highway.in fact, a "manager" there told my wife and i that these things happen, will happen again and if people die, well that's why chrysler keeps a team of lawyers working.
The speed sensor in the automatic transmission failed causing the check engine light to illuminate.nlm
Transmission will not shift into 3rd gear.
Have received no satisfaction from chrysler. No safety defec tlisted.
While driving at any speed and when shifting from first to second gear vehicle stalled.consumer had a certified mechanic check the vehicle, and was told that transmission needed to be replaced.
While diving consumer vehicle shifted from 1st to 2nd gear.
While driving 70 mphvehicle suddenly decelerated to zero. Asa result, vehicle would not accelerate no more than 5 mph. No impact reported.
Vehiclewas lackingpower while driving thenlostpower. Dealer notified, and informed consumer thattramsmission needed to be replaced. Feel free to provide any further information.
While driving at 50 mph, the gear slipped out of drive and into another gear vehicle.
Transmission input sensor failed on my 1999 chrysler concorde lxi with 25,000+ miles causing the transmission to abruptly down shift causing vehicle to over rev engine which caused an abrupt slowdown which could have caused a rear end collision or a loss of control. Part id # is 4800878. Since my failure i have heard of 2 other failures just from people i've talked to. This is a problem chrysler is aware of. They should be held accountable for any accident which this failure contributes to. A safety recall should be initiated. Just for info this repair cost me $161.87. Pretty steep for a known problem!
Gear shift lever was almost impossible to shift into park when parking the car. Turned off the motor and could not get the gear shift lever into park in order to start car.
Gear shift lever veryhard to shift . Originally stuck in drive.
Dt*:the contact stated the vehicle would not shut off, the gearshift was wobbled, and the gear indicator displayed park.the vehicle then accelerated backwards.the transmission was shifted into what appeared to be drive, but slipped into third gear.the vehicle was not taken in for service.there was a nhtsa recall# 04v021000, pertaining to the floor shift.the vehicle was not included in the recall due to the vin.
The consumer stated that her husband put their vehicle in park and got out of the vehicle.when he got out of the vehicle and closed the door, his vehicle began to roll forward.she stated he tried to catch it, but could not.he stated that the vehicle rolled down an embankment and damaged the front and side of their vehicle.no one else was involved.she states that they received a recall notice about 2 wks ago, but forgot exactly what it was for. She stated that her husband could have been seriously hurt if he had stood in front of the vehicle.
There has been a recall on this vehicle (which i never received) while it has been at the dealer a 2nd recall to fix what the 1st recall didn't fix.now they want a $1000 to fix the vehicle but claim that it isn't under recall for the problem.the floor shifter/pin/cable assembly unit. Also the transmission previous complaint # ag#200510260.
Nhtsa recall 04v021000 regarding thefloor shift ignition park interlock.the vehicle was taken to the dealer for the recall.the mechanic replaced the load-limitingfloor shifter lever. The consumer stated a portion of the statement was inaccurate. *tc
While driving and upon turning ignition off, without the key in the ignition, gears moved. Consumer states shift does not lock in park when key was removed.
After getting out ofvehicle while it wasin idle gear went into reverse, and vehicle ran into an embankment before stopping.
Shifter pin to interlock cable broke off causing the ignition key to become removable while the vehicle is in any gear. Yh
While traveling highway speed, the automatic transmission down shifted abruptly with no warning.the owner was able to coast down a ramp onto a side street.the cause stated by a mechanic was that the torque converter destroyed itself. Tsthe motor that operates the drivers side window failed.an electrical component failed causing the battery to discharge.consumer has been refused any compensation for the failure of the torque convertor.*jg
Another chrysler 2.7 litre catastrophic engine failure timing chains failure demolished engine at highway speed.
Problems with trunk release on the dashboard, driver's window, seat belt retractors and the computer chip. *mr ph
The consumer received 3 recall letters on the vehicle since ownership.in every instance, the consumer contacted the local sales and service dealer for a remedy.the dealer advised the parts were not currently available and stated they would contact the consumer once they arrived. The consumer was never contacted by the dealer for the remedies, so the recalls remained open.the most recent recall involved the seat belts.
The contact owns a 1999 chrysler concorde.while driving 45 mph, the vehicle shut off and stopped in the middle of the freeway.the contact was able to maintain control of the vehicle, although the brakes and power steering failed.someone had to assist her with steering the vehicle to the side of the road.the police was called and the vehicle was towed to the auto repair shop.there had not been any engine failure prior to this incident.the auto shop stated that engine sludge coated the engine.it would cost $5,000 to replace the engine.the failure mileage was 60,000. Updated 2/23/09 the passenger seat belt was difficult to unfasten and the rear passenger door had to be opened from the outside. Updated 02/26/09.
Due to location ofbuckle forseat beltconsumer has a problem undoing the belt. The buckle is hard to press and seat belt was placed between the front seats and it is too far.
1999 chrysler concord with engine problems customer wants the blue book value for the car from the dealership**ccthe consumer stated the engine had to rebuilt due to sludge build-up. A mechanic informed the consumer, the vehicle was built with a faulty oil pump, which was too small for the engine. The front seat belt retractor were replaced.
Rear passenger's seatbelt recoiledbut would not come back out. Itwas stuck, causing loss of protection.
Rear seat belt locks were not working properly.the rear seat belts failed to lock and therefore the consumer was unable to place the car seat in vehicle. Ph
Driver's seat back fell backwards while driving. Dealer had been contacted.
The driver seat broke when the consumer hit the brakes . The bolts to the seat broke and the frame to the seat busted. The consume sustained injuries to his neck and back.
Drivers bucket seat failed without warning, causing losts of visibility, nearly caused a crash.
I found five recalls on the safecar.gov site, yet i have never been notified of any of them.in approximately 2000-2001, i had a failure of the driver's seat, while trying to move the seat back for more room, where the back fell all the way down to a reclining position. I was not able to make it stay up.the dealer at the tme repaired it at an approximate cost of $1,100.00. Sometime later, i read in the newspaper later about a recall for the seats, and took it to joliet dodge, joliet, il, who is now out of business. They refused to do anything, telling me i had already had it fixed, and refusing to reimburse me for the cost to repair.fast forward to july 2014.when trying to move the seat back by using the lever for that and pushing back with my body, the seat back totally failed again. It goes all the way down, and will not stay up.because of the age of the car, and the fact that i am a retiree on only social security for a very limited income, and not being able to afford the cost to repair, i did a home made fix by putting my large plastic cooler on the floor in back of the seat to hold it up.i am lucky this happened while the car was in park, not moving, else i might have had a terrible accident. The first time it occurred, i was driving, but had no accident.
Consumer states driver's seat collapsed backward withoutwarning.mr
Dt*: the contact stated the driver's seat was fractured.a nhtsa recall, # 03v035000 was performed on the vehicle concerning, seats: front assembly: recliner on 9-23-03 however, the recall did not remedy the problem.the dealership would not offer a second repair under the recall.08/29/06the right rear stop lamp blub had to be replaced and both front wiper blades were replaced.
While vehicle was parked driver heard a loud noise. Driver's seat collapsed forward.this caused the driver to sustain major injuries, and was transported to the hospital. Vehicle was taken to the dealer for inspection, andmechanicdetermined thatrecliner boltsneeded to be replaced.
The seat back on my 1999 chrysler concorde broke, allowing the seat back to fall back into a reclining position. The car was traveling at a slow speed because i was making a turn.
While traveliingand without any indication driver's seatback broke, causing poor visibility. Please provide further information.
While driving 10-15 mph driver seatback collapsed, vehicle has not been taken to dealership yet. No injuries.consumer stated that the dealer refused to repair this as a safety item, regardless of mileage this was a malfunction or failure of equipment.
Alarmed to see other consumer complaints of similar problems with the steering and failure of rack and pinion and front end suspension.also, we have replaced the sway bar links.we have repeatedly had problems with a/c erratic operation as other consumers reported.fully alarmed by numerous fuel throttle and seatback collapse problems reported.r&p steering unit replaced.steering was real loose.
The dealership refused to honor the recall for the vehicle. Consumer stated the seat bolt was on recall.
Recall 03 v 035 000/seat back reclining bolt. While driving 45 mph the driver's seat completely reclined without warning. No accident or injury reported,butvehicle was serviced for this recall approximately a year ago.
Brakes continuously lock, which causestires to lock and the car skids and pitches forward.our door locks are broken and the bottom portion of the back seat is coming out from the floor.when we purchased the car, we asked the salesperson (tim white) if the car was in good condition and if this was a rental car.he said"it had one owner."when i repeated this to the manager last week, he said it did.he stated that the owner was the rental company in florida.then i pointed out to the manager that one owner did not mean one driver. With it being a rental car it has had many drivers some not so careful as others. If i had been inforrmed of the cars true history and condition, i would never have purchased this automobile.( dot number:)
Recall service for driver seat bolts was performed in 2003.while leaving a stop light the driver's seat unexpectedly reclined fully.the driver regained control of the vehicle and no accident ensued.the driver suffered muscle strain in lower back.no other damage or injury.dealer initially agreed to cover repair, but three days later changed position and will not cover the repair.
The contact owns a 1999 chrysler concorde. The contactstated while driving at approximate speeds of 55 mph, the front drivers seat would recline backward without driver intent due to a bolt snapping. The contact received notification of a recall (nhtsa campaign id number: 03v035000: seats: front assembly: recliner) and took the vehicle to the dealer for repairs. The dealer advised the recall repair was previously performed on the vehicle and the manufacturer would not cover the cost of a second repair. The failure persisted. The failure mileage was unknown and the current mileage was 58,000.
Dt:the front passenger seat reclining bolt broke.
The consumer received 3 recall letters on the vehicle since ownership.in every instance, the consumer contacted the local sales and service dealer for a remedy.the dealer advised the parts were not currently available and stated they would contact the consumer once they arrived. The consumer was never contacted by the dealer for the remedies, so the recalls remained open.the most recent recall involved the seat belts.
Seat bolt recall being ordered.the dealer told the consumer the recall could not be performed because the mechanism under the seat malfunctioned and shorted out the door locking and trunk popping circuitry.
Dt: the contact statedfront passenger seatbroke. The boltloosened and the seat reclined all the way back. Nhtsarecall 03v0350000 was issuedon the seat, but it affected the driver's side only. He had no current plan torepair the vehicle.
In may 2003, the consumer made an appointment with the dealer for recall # 03v035000 repairsconcerning seat back reclining bolt.upon arriving for the appointmentdealer stated there were no parts available.consumer has not received a call from the dealer stating when the parts would be available.
Consumer had the driver's seat repaired according to nhtsa recall campaign03v035000 for the reclining seat position. Now the passenger seat broke and collapsed back.the back of the seat was stuck and would not come up at all. The passengersunable to sit up in a regular seatedposition.
One year laterafterconsumer receivednhtsa recall letter03v035000 the seatback recliner unexpectedly broke. Passenger sustained a cut onthe forehead,and knee bruiseswhen he came in contact with the dashboard.
1999 chrysler concorde engine failure at 90000 whille wife and children in traffic engine failure due slug build up. Mechanic said it would cost $4600.00 to replace engine still owe 11000 on it, and cant afford to repair. Mechanic said slug build up is due to oil pump design also have ac problemand have had radiator fan failure twice , speed sensor failure, broken window clips,brake shimmy , broken recliner seat bolts
Dt*:the consumer stated the brake pedal must be pressed down too far to stop the vehicle.the vehicle has been to the dealership and multiple independent repair shops, but there was no repair available.the manufacturer determined this is how the vehicle was made.also, the headlight gasket continuously falls out but no repair is available. Updated 03/28/06.
On 6/12/03 i filled out a vehicle owners questionnaire on a 1999 chrysler concorde, vin [xxx]. On 8/02/02 i purchased this chrysler concorde with 48,580 miles.on 8/15/02, i took the car back to [xxx] because of electrical problems, car leaking oil,brakes sticking,and air, heater,defrost,ventilation problems.upon arrival to [xxx]on 8/15/02 to drop the car off to be serviced there were 48,620 miles on the odometer. After receiving a phone call from [xxx]dealership stating "that the car was ready." "and had been serviced." after arriving and getting in the car, i noticed that the odometer had been changed, because it was now reading 48,883 miles.i then questioned [xxx]about the additional miles and was told "been everything had fixed."on 4/15/03, i was back at [xxx]having electrical problems in the dashboard. And the air conditioner was blowing out hot air.in the month of may 2003, i received a recall notice about the driver's seat bolt being defective, which may break causing the seat to suddenly recline. I took the car in on 5/27/03 to have the bolt replaced. After being at the dealership for about two minutes i was told that "the car was ready to go." i asked if the bolt had been replaced? i do not believe it had because it was not gone long enough. I also had to request a customer's copy of the invoice. When i received the invoicei notice that the invoice stated that the car wasgray. The car is black.pleaselookinto this matter.thank you[xxx] *sccinformation redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6).
The brake pedal locked up when the brakes were applied, which caused extended stopping distance.
Brake power booster failed.*mr ph
Have received no satisfaction from chrysler. No safety defec tlisted.
While driving on i-95 at 60 mph the vehicle started rapidly accelerating on it's own with my foot off the gas pedal. Applied brakes and shifted to neutral. Came to a stop. Put car in park and then into drive and car rapidly accelerated, tires smoking! brakes applied at maximum pressure car still accelerated. Shifted to neutral and turned key off.
When coming to a stopbrakes made a grinding noise. Dealer said there was a defect inthe brakes, and that the grinding was a normal noise. *ml
1999 chrysler concorde v-6 3.2l:brakes drop to 20% power in cold weather.no warning. No brake lite on dashboard.20% brakes are effective enough at at slow speed and initial departure from parking spot.lack of full power is not evident until full power is applied. Brakes return back to 100% power after warmer weather.after prolonged cold weather, the brake pedal freezes in place.rubber boot on piston forward of brake pedal covered with rusty dust & shows possible exposure to interior water leak.in process of repairs now.
When the brakes were applied the pedal went to the floor, resulting in extended stopping distance, and causing a collision which resulted in minor injuries.vehicle was tataled.the dealer has been notified.
I put car in reverse in parking lot and it lunged forward at full throttle with tires smoking, sideswipping one vehicle and pushed parked 2nd vehicle 30 ft into parking lot isle.my foot never left the brake pedal (used to shift), and brakes were useless in trying to stop the car.after hitting the second car (totalling it) got car stopped by slamming gear shift lever into park.this is the 3rd instance of this happening in the milwaukee area that is known to us.substancial injuries were incurred in second instance where car when through garage door with severe facial injuries. The 3rd car went through a window of a business.all 3 were 1999 chrysler products.chrysler refuses to accept any blame for the accident and sent us a form letter saying the car was okay when it left the factory.our car was a chrysler concorde lxi, the 2nd a chrysler lhs, and the 3rd a dodge neon.
Brakes continuously lock, which causestires to lock and the car skids and pitches forward.our door locks are broken and the bottom portion of the back seat is coming out from the floor.when we purchased the car, we asked the salesperson (tim white) if the car was in good condition and if this was a rental car.he said"it had one owner."when i repeated this to the manager last week, he said it did.he stated that the owner was the rental company in florida.then i pointed out to the manager that one owner did not mean one driver. With it being a rental car it has had many drivers some not so careful as others. If i had been inforrmed of the cars true history and condition, i would never have purchased this automobile.( dot number:)
While driving 60 mph vehicle accelerated to 80 mph,and brakes did not slow down vehicle. Consumer shut off engine.
Brakes locking up while cruise control on causing vibration, burning smell and smoke to come from the wheels.
1999 chrysler concorde engine failure at 90000 whille wife and children in traffic engine failure due slug build up. Mechanic said it would cost $4600.00 to replace engine still owe 11000 on it, and cant afford to repair. Mechanic said slug build up is due to oil pump design also have ac problemand have had radiator fan failure twice , speed sensor failure, broken window clips,brake shimmy , broken recliner seat bolts
The contact owns a 1999 chrysler concorde.the contact stated that the abs light illuminated and she heard a noise in the engine compartment.the mechanic stated that the pump motor circuit for the abs failed and caused the light to illuminate.the approximate cost to repair the vehicle was between $1,500 to $2,000.the front rotors were replaced in april of 2006 and in september of 2007.in january of 2007, the front driver side bearing was replaced.the mechanic stated that the failure was due to poor design and cheap parts.the air conditioner also began to leak.the mechanic stated that there was a hole in the suction line because of the design, and it rusted and rubbed through another part of the vehicle.the air conditioning suction line was replaced in september of 2007.the leak could have potentially caused a fire.the mechanic stated that the power steering kit needed to be replaced.the vehicle could easily rust into the frame and condensation could collect.the vehicle is currently hesitating and surging.the current mileage was 78,100 and failure mileage was 78,000.updated 03-04-08 the leak of the power steering hose could cause a fire. Updated
Failure of inner tie rod end and steering box.
Consumer states that while driving at any speed on flat surface and without warning the steering wheel seize up causing a distraction to the consumer. Dealer notified. Ts
While driving the vehicle at any speed the power steering wheel is not working properly, making hard the consumer to drive the vehicle. Please provide further information thank you. Ts
Steering wheel locked up.
Vehicle:1999 chrysler concorde lxi,pproximate milage:50,000problem:steering wheel; rack and pinion:( 1.)the steering wheel jams and i have to jerk the steering wheel to release it.( 2.)there is also 1/2" to 1" of play in the steering wheel either way when it is "working properly".the problemstarted intermitently then rapidly worsened.i spoke to a mechanic and he said this is a common problem with this model.my coworker is approching 50,000 miles with a 2000 chrysler 300m, (an upgrade, but basiclly the same car), he is having the same problem.i have contacted diamler chrysler, but have gotten nowhere.i am taking it to the shop 6/21/04 to be fixed.this is a very expensive problem and seems to occure at around 40000 to 50000 miles, (chrysler said they would have split the cost with me if the milage wasn't so high). I feel that this problem seriously needs to be followed up on.it is a huge safety problem.
The contact owns a 1999 chrysler concorde.the contact stated that the abs light illuminated and she heard a noise in the engine compartment.the mechanic stated that the pump motor circuit for the abs failed and caused the light to illuminate.the approximate cost to repair the vehicle was between $1,500 to $2,000.the front rotors were replaced in april of 2006 and in september of 2007.in january of 2007, the front driver side bearing was replaced.the mechanic stated that the failure was due to poor design and cheap parts.the air conditioner also began to leak.the mechanic stated that there was a hole in the suction line because of the design, and it rusted and rubbed through another part of the vehicle.the air conditioning suction line was replaced in september of 2007.the leak could have potentially caused a fire.the mechanic stated that the power steering kit needed to be replaced.the vehicle could easily rust into the frame and condensation could collect.the vehicle is currently hesitating and surging.the current mileage was 78,100 and failure mileage was 78,000.updated 03-04-08 the leak of the power steering hose could cause a fire. Updated
Vehicle:1999 chrysler concorde lxi,pproximate milage:50,000problem:steering wheel; rack and pinion:( 1.)the steering wheel jams and i have to jerk the steering wheel to release it.( 2.)there is also 1/2" to 1" of play in the steering wheel either way when it is "working properly".the problemstarted intermitently then rapidly worsened.i spoke to a mechanic and he said this is a common problem with this model.my coworker is approching 50,000 miles with a 2000 chrysler 300m, (an upgrade, but basiclly the same car), he is having the same problem.i have contacted diamler chrysler, but have gotten nowhere.i am taking it to the shop 6/21/04 to be fixed.this is a very expensive problem and seems to occure at around 40000 to 50000 miles, (chrysler said they would have split the cost with me if the milage wasn't so high). I feel that this problem seriously needs to be followed up on.it is a huge safety problem.
I have been without my 1999 car (5) times.my complaint regarding the "front left" has been the same each time the care was in for service.each time the "symptom" was not fixed.this time the rack and pinion is being replaced.
There is loosnessinsteering wheelwhenturning a corner. Dealer has replacedrack andpinion. Please provide additional information.
Alarmed to see other consumer complaints of similar problems with the steering and failure of rack and pinion and front end suspension.also, we have replaced the sway bar links.we have repeatedly had problems with a/c erratic operation as other consumers reported.fully alarmed by numerous fuel throttle and seatback collapse problems reported.r&p steering unit replaced.steering was real loose.
Steering rack corroded, dealer replaced rack and pinion.all four power window motors burned, dealer replaced.heater fuse box was burned, dealer replaced.
Steering gear is faulty, as diagnosed by a chrysler authorized service rep. Steering gear emits loud clunking noises when vehicle is driven on non smooth roads. Dealer refuses to replace steering gear under warranty conditions.condition has worsened during last 15000 miles.
Problems in steering ,noise and loose control when i driving , i send my car numerou time todealer without resolve this problem.
Crack in dashboard over airbag.
While driving at 50 mph the trim plastic which covers the windshield wipers fell off. Dealer replaced the part atconsumer'sexpense of $152.00.
Yesterday i had to go to the hospital because the trunk lid fell on my neck when i was unloading my trunk.this car has an electrical trunk that opens and the trunk also, has a spring air rod that controls the hold of the open trunk.i know this failed because the trunk just lost its hold all of a sudden and landed on my neck.as i tried to lift it from above me (its very heavy- big trunk), my left hand indexfinger broke and my left arm and hand are in pain.not to mention, the severe pain i am undergoing with my neck. I also bled a lot and immediately went to the emergency room.i believe this can be a manufacturing defect due to the excessive weight of this trunk door and the device being relied on for the control of trunk.
I was parking on a parking lot and lot had a structured small post on the driver side; due to visibility that the vehicle lamp omitted to light properly, i damaged the front right corner bumper.i have noticed thatthe corner lamp assemblies have a problem with the reflectors.this lamp doesn't have the required amber side reflectors don't work well cause i can barely see (not like my other cars).there is a recall set already for part number cs114-u0bj2 which is a combination corner and lamp assembly for this vehicle.i am asked to contact sabersport who is doing the recall (recall id#09e012000 exterior lighting); however, their number is disconnected and their online contact number is a wrong number.at this point, i don't think its right that i have to pay for these repairs.even upon repairs,i need the vehicle with correct lamp assembly so it doesn't happen again.next time, could be a worse accident.[xxx]information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6).
The driver is unable to lock the glove box. Yh
The molding between the hood and the windshield flew off as i was driving in the freeway.i was driving like i normally do ( approx. 65mph), when fwy is clear of cars; this is not reason enough for this car part to fly off.luckily, fwy was clear, if not, i could of had an accident since it affected my visibility while driving.once i replace this, i wonder if next time... Will i have an accident? how to ask they install it so it doesn't fly off? dealer says they must install it per manufacturer requirements but the normal way it comes from manufacturer doesn't work cause it eventually flies off.i noticed there are countless complaints regarding same issue with nhtsa.how many complaints are necessary for it to be recalled?
The contact owns a 1999 chrysler concorde. The contact stated that the passenger and driver side door handle broke; as a result she was unable to unlock the doors in order to exit the vehicle. The contact alsomentioned that the automatic locks and interior lights would turn on and off. The vehicle was taken to a local mechanic who decided to glue the handle back on as a temporary remedy. The remedy failed to repaired the problem since the handle came off completely. The manufacturer was made aware of the failure but did not offer any assistance since the vehicle was not included in any recalls. The vehicle was not repaired. The failure mileage was unknown and the current mileage was 85,000.
Ctuator forelectric door lockshas been replaced several times. Problemlocks will not disengage when t door needs to be opened.even the key todoor fails to unlockvehicle. Dealership cannot find an effective remedy for this problem.please provide any additional information/attachments.
Door autolock mechanism failure, power window failure prior to the april 13, 2001 incident.parked in driveway, picked up four children.engaged car in reverse, automatically accelerated at a minimum of 20mphs, applied brakes would not work, tried putting car in neutral, tried shutting off car, had to turn wheel of car to avoid hitting a house across the street, car continued to move forward over a curb and finally stopped once it hit bushes in a neighbors yard.vehicle was inspected by chrysler special investigations, was informed thatno association was made in any manufacturing or assemby system defects.throttle cable was not binding and was operating normally, hoses in tact per chrysler.referred to my insurance agency to file a claim.car max the dealerwhere i purchased the car offered no assistance as well.november 12, 2001 took car in to have repairs done to doors and windows, left door lock mechanism replacement $300.00, all four window regulator assemblies had gone bad.over $1,000 to repair.
The plastic piece on the hood blew off while driving 60 mph on the highway. The manufacturer stated that several other vehicles experienced the same problem, and the part #4805701-ab was on back order.
The cowl panel replaced by hood molding 4805701ab, change of design from original molding that blew off. The consumer was driving. On a windy day.the cross wind from an open panel truck caused the cowl panel on the hood to come off.the panel hit the windshield but caused no damage.
Dt: the consumer stated that the cowl molding flew offhood and hit the windshield. The windshield did not break. The vehicle was a 1999 chrysler concorde. Theconsumer contacted chrysler, and the consumerstated that chrysler did not know what the part was called. The consumerthen called the dealer, and they had one in stock. The consumer did not plan on replacing the part.
Plastic trim molding, that is between the glass and the hood, is rattling severely. Consumer feels that this molding may fly off at high speeds. Also, trunk lid springs failed to keep the trunk propped up safely.
Dt: contact stated that the trunk lid fell on his head and caused an injury. The lifts that hold the trunk lid up failed. The dealer has not been contacted yet. The manufacturer informed him there were no recalls on the trunk and offered no free remedy.he had the problem for two years, but did not experience an injury until now. The lifts that hold the truck lid open were not replaced after the injury.
Dt:the contact stated thataccording to the mechanic at the local dealership, the hydraulic lift that holds up the trunk was not designed to hold the load.the trunk fellon him, butdid not injure him.the dealership stated the hydraulic lifts need to be replaced on both sides.this has been happening since purchase of vehicle.also, hestatedthe vehicle waslow to the ground, the front end scraped when backingof the driveway or driving over a bump.he tookthe vehicle to two dealerships, and was willing to pay out of pocket.both dealerships stated there was nothing that could be done.updated 11/30/2005 -
Dt:the contact stated the mechanic at the local dealership told him the hydraulic lift that holds up the trunk was not designed to hold the load.while in use the trunk fell and hit him in the neck.he usually can catch the trunk before it falls.this has been happeningsince purchase of vehicle. The dealership statedthe hydraulic lift needed to be replaced on both sides. Also,stated the vehicle was low to the ground, the front end scraped while backing out of the driveway or driving over a bump.he has taken the vehicle to two dealerships, and was willing to pay out of pocket.both dealership stated there was nothing that could be done.
The plastic trim molding, that is between the glass and the hood, is rattling severely.consumer feels that this molding may fly off at high speeds. Also,consumer hasa problem with the trunk hydraulic lifter failing to keep the trunk propped up safely.
The vehicle ran over an object in the road, and minutes later theentire front end of the vehicle collapsed.
Vehicle is rattling underneathand thewill not go over forty miles on highway.dealership is aware ofproblem.
Update to previous report assigned odi id: 707635.vehicle has without warning shuddered violently on 3 occasions, once at 25-30 mph and twice at 67 mph.malfunction could not be replicated after 90 miles of test driving.no problems apparent with suspension or steering.no engine or tcm fault codes recorded.at this point cause unknown.
On 3 separate occasions over 3 days,vehicle began to shudder violently.once at 35 mph and twice at 65 mph.applying brakes did not stop problem.only when speed came down to 35 - 45 mph.two dealers have inspected the tires, engine, transmission and suspension without result.while problem has not recurred since 5/30, there could be a serious accident if it occurred again at high speed in heavy traffic.
I have been without my 1999 car (5) times.my complaint regarding the "front left" has been the same each time the care was in for service.each time the "symptom" was not fixed.this time the rack and pinion is being replaced.
Dt:the contact stated thataccording to the mechanic at the local dealership, the hydraulic lift that holds up the trunk was not designed to hold the load.the trunk fellon him, butdid not injure him.the dealership stated the hydraulic lifts need to be replaced on both sides.this has been happening since purchase of vehicle.also, hestatedthe vehicle waslow to the ground, the front end scraped when backingof the driveway or driving over a bump.he tookthe vehicle to two dealerships, and was willing to pay out of pocket.both dealerships stated there was nothing that could be done.updated 11/30/2005 -
Door's automatic locking mechanism/ power windowsfailed, and engine was making loud noise . Also,and front alignment malfunctioned twice. Dealer notified.
When traveling at highway speed around or about 50-60 mph vehicle pulled to the left, causing poor steering control. Consume has contacted the dealer, dealer noticed tsb for the same type of problem. Dealer corrected the problem by installing a small bolt to support the large bolt struts.consumer still having problems. Please provide any further details.
Alarmed to see other consumer complaints of similar problems with the steering and failure of rack and pinion and front end suspension.also, we have replaced the sway bar links.we have repeatedly had problems with a/c erratic operation as other consumers reported.fully alarmed by numerous fuel throttle and seatback collapse problems reported.r&p steering unit replaced.steering was real loose.
Dear sir: i would like to know if chrysler has replaced the sway bar links and trailing arms on the cars coming off the assembly line?the dealer told me they do not know.i am planing onbuying a new concorde lxi in the near future. Please responde.i do not know where else i can get this info. Thank you charles field
The contact owns a 1999 chrysler concorde.the contact stated that the abs light illuminated and she heard a noise in the engine compartment.the mechanic stated that the pump motor circuit for the abs failed and caused the light to illuminate.the approximate cost to repair the vehicle was between $1,500 to $2,000.the front rotors were replaced in april of 2006 and in september of 2007.in january of 2007, the front driver side bearing was replaced.the mechanic stated that the failure was due to poor design and cheap parts.the air conditioner also began to leak.the mechanic stated that there was a hole in the suction line because of the design, and it rusted and rubbed through another part of the vehicle.the air conditioning suction line was replaced in september of 2007.the leak could have potentially caused a fire.the mechanic stated that the power steering kit needed to be replaced.the vehicle could easily rust into the frame and condensation could collect.the vehicle is currently hesitating and surging.the current mileage was 78,100 and failure mileage was 78,000.updated 03-04-08 the leak of the power steering hose could cause a fire. Updated
Dt*: the contact stated while driving 70 mph on normal road conditions, the driver side and passenger side trailering arm-link fractured.the nature of the failure was permanent.there were no warnings prior to the incident. Updated 12/05/06.
Alarmed to see other consumer complaints of similar problems with the steering and failure of rack and pinion and front end suspension.also, we have replaced the sway bar links.we have repeatedly had problems with a/c erratic operation as other consumers reported.fully alarmed by numerous fuel throttle and seatback collapse problems reported.r&p steering unit replaced.steering was real loose.
Vehicle has been experiencing ongoing problem with engine check light keep coming on. Vehicle has been in / out of dealer shop on three occasions, andproblem isstill unresolved.
I had a a/c diagnostics test at maxwell(chrysler/plymouth) 6905 i.h. 35 south austin, texas 78715 on april 5, 2003. Service advisor: 9 doug shaw told me i needed fan belts(two at $165), rt cooling fan motor soon($236.00 for cooling fan motor, and other engine cooling fan motor replaced but if cooling fan motor only at $322.14), evaporative coil(at cost $1035.00), evac&recharge-add dye($145.00 cost) for testing. I had someone else put on the rt cooling fan motor and put fill it up with freon. It is still not working properly. Sometimes it will come on and blow cold air sometimes it won't. But it will not come on right away.driver's door radio door speaker has a buzz.
Consumer inquired as to whether a recall part could have caused other malfunctions.*ph
We were driving down the highway and the plastic piece flew off the car. Luckily nobody was driving behind us i'm sure it would have hit them.
I have a knocking noise in the front end.service mechanics can't find the source of the problem.it is getting worse.
Air conditioning continually goes out. As car has expired warranty, chrysler says they have no obligation to repair. I disagree. I believe that chrysler, and in my particular situation, has a faulty a/c system.
1999 chrysler concorde engine failure at 90000 whille wife and children in traffic engine failure due slug build up. Mechanic said it would cost $4600.00 to replace engine still owe 11000 on it, and cant afford to repair. Mechanic said slug build up is due to oil pump design also have ac problemand have had radiator fan failure twice , speed sensor failure, broken window clips,brake shimmy , broken recliner seat bolts
I had just pulled into a parking space and was about to shift from drive to park when my 1999 concorde took off jumped a curb stop and hit a tree, where the engine continued to accellerate and the wheels dug 5-6 inch ruts in the ground, before reversing jumping back over the curbing and stopping.the whole time my foot was also on the brake which didn't respond.
Consumer states that put vehicle in gear and acceleratedand vehicle took off full throttle.nlm
Hi i need to ask if the probelm on thesearch page .of the car surging out of controll and hiting thingor killing the 2 people .i wont to know if the problems all from the same person. I see most of the complaints are from a person or astate which i do not know. But it end in . Is this a person lastand frist mane. Or is this a stat in which it happen .i just got my wife this car one day ago . Because it help her back and it was a smooth riding car. Can you email back or call meif itis a problemi need to know what i can doto fix it or get thedealer to fix it . . thank you i need to know so i can save my wife from any harme. If this happensthank you alex in sunny ca.
While driving 60 mph vehicle accelerated to 80 mph,and brakes did not slow down vehicle. Consumer shut off engine.
My wife was backing out of a parking space when her car surged out of control, hitting a repair vehicle and grocery cart stand.most of the right side of the car was damaged.the dealer has declared nothing wrong with the vehicle, but this was an uncontrolable situation and only by luck was no one hurt.
The car i was driving was a 1999 chrysler concord that had been in excellent driving up until the time of the incident.just three days earlier the automobile was serviced at a chrysler dealership service center for an oil and oil filter change. I inquired at the pick up event if the brakes were okay and it was reported to me that the were fine and that everything with this automobile was fine.on sunday, september 3, 2006, i started this automobile in my garage to go to church. After putting my seat belt on, i usually inch myself out of my garage very, very slowly. However, this time after adjusting the transmission lever from park to drive my automobile took off so fast i could not control it at all. I hit the breaks as hard as i could but my automobile would not slow down at all. Not only that, i could control the steering of my automobile at all. I live near the pacific ocean and there is a drainage ditch right across the street where i live that connects with the ocean. There is a chain-linked wire fence that separates the street from the drainage ditch.my automobile raced out of my garage, down my driveway, went across the street and hit the curb across the street where it force my automobile to swerve across the adjoining street to break through the chain-linked fence where it went down a concrete embankment for an approximate 20-foot drop until it completely stopped in the water. The car then began filling up with water until it became completely submerged. Fortunately, a neighbor happened to be looking out of his second story window of his house when this incident occurred and immediately called 911. Emergency personnel arrived promptly to save my life by pulling me out of the window of my automobile. I was taken by paramedic personal by ambulance to the emergency room of a nearby hospital were it was determined i had not sustained any immediate injuries at all.the automobile was later determined to be a totaled wreck.
Immediately after starting car & putting it into gear, it took off at a high rate of speed, even while foot was on brake pedal.driver served to avoid parked cars and went through a fence hitting a ditch, went across a street, hit another ditch before stopping. Also, there was no deployment of air bags. *cj
I put car in reverse in parking lot and it lunged forward at full throttle with tires smoking, sideswipping one vehicle and pushed parked 2nd vehicle 30 ft into parking lot isle.my foot never left the brake pedal (used to shift), and brakes were useless in trying to stop the car.after hitting the second car (totalling it) got car stopped by slamming gear shift lever into park.this is the 3rd instance of this happening in the milwaukee area that is known to us.substancial injuries were incurred in second instance where car when through garage door with severe facial injuries. The 3rd car went through a window of a business.all 3 were 1999 chrysler products.chrysler refuses to accept any blame for the accident and sent us a form letter saying the car was okay when it left the factory.our car was a chrysler concorde lxi, the 2nd a chrysler lhs, and the 3rd a dodge neon.
While backingvehicle out of the garage it suddenly accelerated, resulting in a collision. Dealer has been notified.
I was at a car wash with my car running and in park.i shiftedwhen my car surged backward out of control hitting the car behind me.when i put the car in park after the crash the engine was roaring.no one was injured but it did over $800.00 damage to my car and $3000.00 damage to the car behind me.
The vehicle was in an accident due to a malfunction of the engine. The vehicle unexpectedly began to accelerate.the owner shut off the engine and applied the brake, but the motor was going at such a high speed,the vehicle did not stop.the police did take a report.the consumer was looking for a place to park whenall of a sudden the vehicle had gone at an uncontrollable speed and when the consumer shut off the ignition and braked, the consumer hit a parked vehicle. *sc
Consumer was pulling out of parking garage and putvehicle in gear and the vehicle pulled off on its own very fast, causing the consumer to crash into another vehicle. Air bags did not deploy . Dealer has been contacted.
Vehicle accelerated suddenly when put into drive range.driver could not stop vehicle by braking.braking skids left on paving.vehicle traveled approximately 300 feet beforecolliding with a concrete block wall,totallingvehicle and wall.
Problems with speed sensors on chrysler concorde.*mrthe consumer was very concerned about the speed sensor problem, and feels that it should be addressed.two incidents occurred with in a year of purchasing the vehicle. Please respond promptly in resolving matters. The windowmotor failed and the headlight devices fell off.
I own a 1999 chrysler concorde lxi.i have had numerous problems with this car since i have owned it.lot of little things. Window motors, cooling fan, transmission overspeed sensor, and the list goes on.now the air conditioner is going out, having to service it about every 2 months.why i am writing though is the steering.seems like it is going bad.i feel this is a safety issue and read many complaints on your web site concerning this.why hasn't a recall been ordered for this and the speed up issue?
Have received no satisfaction from chrysler. No safety defec tlisted.
When putting vehicle in reverse withbrake applied, vehicle accelerated suddenly and unexpectedly,resulting in a collision.manufacturer has been notified.2 people were injured in accident.
Alarmed to see other consumer complaints of similar problems with the steering and failure of rack and pinion and front end suspension.also, we have replaced the sway bar links.we have repeatedly had problems with a/c erratic operation as other consumers reported.fully alarmed by numerous fuel throttle and seatback collapse problems reported.r&p steering unit replaced.steering was real loose.
Sudden acceleration after startup an put into gear.hit building across street.
While driving on i-95 at 60 mph the vehicle started rapidly accelerating on it's own with my foot off the gas pedal. Applied brakes and shifted to neutral. Came to a stop. Put car in park and then into drive and car rapidly accelerated, tires smoking! brakes applied at maximum pressure car still accelerated. Shifted to neutral and turned key off.
Car had been returned to driver after coming out of a car wash.vehicleaccelerated out of control, causing an accident and fatality to the driver of the concorde.
Sticking throttle or gas pedal.
Accelerator malfunction. 1999 chrysler concorde accelerator stuck, unable to engage the braking system so turned car off. Lost steering, braking control and hit a barricade, totaling vehicle and causing concussion and head to toe bruising.
After depressing gas pedal it became stuck, causing consumer to hit another vehicle, and a pole. Dealer has been contacted. Please provide further information.
1999 chrysler concord brake equipment became inoperative during operation of the vehicle. *mr the consumer place the vehicle in drive and the vehicle "took off."the accelerator stuck.the vehicle was totaled. *sc
While driving, the accelerator pedal assembly came apart. The owner ordered the part for repair.the owner also contacted the manufacturer but was not given any assistance. Provide further details.
I had just left church, and got into my car to come home.i put on my seat belt, moved the seat forward, checked the mirrors, and with my foot depressing the brake, took off the emergency brake, and looked over my left shoulder.as i did this, i viewed a white car stopped about two cars length behind me, waiting to exit the parking lot.they waived to me to go ahead.at this point my car was completely stopped.the column shifter was in reverse, and my foot was still on the brake pedal, when all of the sudden my car ( by itself ) went into full acceleration forward, about one and a half car lengths hitting a tree, without my shifting anything on the shifting column.the airbag did not deploy.the impact stirred up a huge amount of dirt and dust in front of my windshield.the tree was the only thing that stopped my car as the motor was still in full acceleration as i reached to turn off the ignition.many witnesses gathered around my car coming to my door to see if i was hurt.i have been in touch with daimler chrysler, and they refuse to except liability for what i am sure is a malfunction in this car!the exact same thing happened to my husband with this same car in sept of 1999, only the car went into full acceleration in reverse.
When driving and upon making a graudal stop after cutting off and restarting vehicle with foot depressed on the brake pedal,vehicle took off, resulting in unwanted and unexpected acceleration which caused consumer to run into a bridge. Consumer has contacteddealer. Please provide any further details.
The molding between the hood and the windshield flew off as i was driving in the freeway.i was driving like i normally do ( approx. 65mph), when fwy is clear of cars; this is not reason enough for this car part to fly off.luckily, fwy was clear, if not, i could of had an accident since it affected my visibility while driving.once i replace this, i wonder if next time... Will i have an accident? how to ask they install it so it doesn't fly off? dealer says they must install it per manufacturer requirements but the normal way it comes from manufacturer doesn't work cause it eventually flies off.i noticed there are countless complaints regarding same issue with nhtsa.how many complaints are necessary for it to be recalled?
On 6/12/03 i filled out a vehicle owners questionnaire on a 1999 chrysler concorde, vin [xxx]. On 8/02/02 i purchased this chrysler concorde with 48,580 miles.on 8/15/02, i took the car back to [xxx] because of electrical problems, car leaking oil,brakes sticking,and air, heater,defrost,ventilation problems.upon arrival to [xxx]on 8/15/02 to drop the car off to be serviced there were 48,620 miles on the odometer. After receiving a phone call from [xxx]dealership stating "that the car was ready." "and had been serviced." after arriving and getting in the car, i noticed that the odometer had been changed, because it was now reading 48,883 miles.i then questioned [xxx]about the additional miles and was told "been everything had fixed."on 4/15/03, i was back at [xxx]having electrical problems in the dashboard. And the air conditioner was blowing out hot air.in the month of may 2003, i received a recall notice about the driver's seat bolt being defective, which may break causing the seat to suddenly recline. I took the car in on 5/27/03 to have the bolt replaced. After being at the dealership for about two minutes i was told that "the car was ready to go." i asked if the bolt had been replaced? i do not believe it had because it was not gone long enough. I also had to request a customer's copy of the invoice. When i received the invoicei notice that the invoice stated that the car wasgray. The car is black.pleaselookinto this matter.thank you[xxx] *sccinformation redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6).
I bought a 1999 chrysler concorde that started off with no heat (replaced heater core) then had tranny fluid in the radiator(replaced radiator) now the engine seized and has anti-freeze in the oil. This all happened within a month of purchased.
Problems with trunk release on the dashboard, driver's window, seat belt retractors and the computer chip. *mr ph
Both the front drivers window and front passenger window the clips fell off the window and both windows were replaced.i do have a piece of one of the clips.
Dt:1999 chryster condorde, consumer had turned the air conditioner on, and the air conditioner had been on for a while, the driver's side window exploded on the consumer.the temperature that day was around 101 degrees. Consumer was injured slightly from the broken glass.
Problems with speed sensors on chrysler concorde.*mrthe consumer was very concerned about the speed sensor problem, and feels that it should be addressed.two incidents occurred with in a year of purchasing the vehicle. Please respond promptly in resolving matters. The windowmotor failed and the headlight devices fell off.
The drivers side window fell off the track.*nlm.
While traveling highway speed, the automatic transmission down shifted abruptly with no warning.the owner was able to coast down a ramp onto a side street.the cause stated by a mechanic was that the torque converter destroyed itself. Tsthe motor that operates the drivers side window failed.an electrical component failed causing the battery to discharge.consumer has been refused any compensation for the failure of the torque convertor.*jg
Car has popping sound around left front wheel,all but one window is off track and cant use.have to bang key on end to get it to turn ignition over.car shakes when braking.wont stay in alignment.uses oil from first day we bought car.when windows did work they snapped shut loudly.this is a smooth riding car but has way to many problems.also the tv cable broke and had to be replaced which was the only component that wasnt covered on the warranty.kinda strange since the car wont budge without it..i am sorry i ever bought this car.i am paying for a vehicle that will be trash by the time it is paid for.
Power windowsfail to come down due to electrical failure. Dealership has examinedvehicle six times and failed to remedyproblem.please provide any additional information/attachments.
All of the power windows have failed over time. I believe the window is forming a seal with the rubber gasket at the top of each window. The power moter for the window does not have enough torque to break this seal to open the power window. All of the power windows have now failed over period of 6 months.
Door's automatic locking mechanism/ power windowsfailed, and engine was making loud noise . Also,and front alignment malfunctioned twice. Dealer notified.
I own a 1999 chrysler concorde lxi.i have had numerous problems with this car since i have owned it.lot of little things. Window motors, cooling fan, transmission overspeed sensor, and the list goes on.now the air conditioner is going out, having to service it about every 2 months.why i am writing though is the steering.seems like it is going bad.i feel this is a safety issue and read many complaints on your web site concerning this.why hasn't a recall been ordered for this and the speed up issue?
Driver's and passenger's side windows had to be replaced.2 days later, the right rear window failed. Dealer statedthat the electronic motor needed replacement. Also,front driver's side window needed to be replaced again.
Steering rack corroded, dealer replaced rack and pinion.all four power window motors burned, dealer replaced.heater fuse box was burned, dealer replaced.
This is the message that i sent to chrysler corporation on 4/8/2003.i am having a problem with the items below.the car is a 1999 chrysler concorde lxi.i purchased it used sept. 2002.i currently have 46201 miles on the car and by looking at the information on you website see that i am not the only individual to have these problems.my rear driver's side window is not working.it worked when i purchased the car, but now it doesn't even go down.i am having it replaced, but am not happy that a car only 3 years of age has such a problem.i have already done my research and have realized that i have purchased a car with numerous problems.also, the front passenger door lock mechanism (actuator) also has to be replaced.it is currently making a very loud pitched noise when activating the locking feature.the unlock doesn't make the noise.i would appreciate a response about this information.i will also be contacting the nhtsa about these issues so they are aware of them.when at the dealer today, 4/8/2003, the service person said that the door lock mechanism has been a consistent problem.i really don't think that i will be purchasing or persuading an individual to purchase a chrysler product.sincerely, [xxx]. *nlminformation redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6).
Door autolock mechanism failure, power window failure prior to the april 13, 2001 incident.parked in driveway, picked up four children.engaged car in reverse, automatically accelerated at a minimum of 20mphs, applied brakes would not work, tried putting car in neutral, tried shutting off car, had to turn wheel of car to avoid hitting a house across the street, car continued to move forward over a curb and finally stopped once it hit bushes in a neighbors yard.vehicle was inspected by chrysler special investigations, was informed thatno association was made in any manufacturing or assemby system defects.throttle cable was not binding and was operating normally, hoses in tact per chrysler.referred to my insurance agency to file a claim.car max the dealerwhere i purchased the car offered no assistance as well.november 12, 2001 took car in to have repairs done to doors and windows, left door lock mechanism replacement $300.00, all four window regulator assemblies had gone bad.over $1,000 to repair.
1999 chrysler concorde engine failure at 90000 whille wife and children in traffic engine failure due slug build up. Mechanic said it would cost $4600.00 to replace engine still owe 11000 on it, and cant afford to repair. Mechanic said slug build up is due to oil pump design also have ac problemand have had radiator fan failure twice , speed sensor failure, broken window clips,brake shimmy , broken recliner seat bolts
Rear passenger window has never worked since i've owned the car.driver's window recently fell out of the track and i believe the window motor is close to failing.
When driving, the center field of view is distorted, creates excessive visual fatigue and dizzyness when driving on highway. Never cpmplained about it, originally believed it was part of design of "cab forward"yesterday while on trip, 2nd driver complained of dizzyness and discussed problem. Definitely is a problem.
The contact owns a 1999 chrysler concorde. The contact was driving approximately 70 mph when the windshield wiper cowl, a part which covered the base of the windshield washer, ejected from the vehicle. The vehicle was not diagnosed or repaired for the failure. Neither the dealer nor the manufacturer was contacted.the failure mileage was unavailable.
Dt*: the contact stated the driver's seat was fractured.a nhtsa recall, # 03v035000 was performed on the vehicle concerning, seats: front assembly: recliner on 9-23-03 however, the recall did not remedy the problem.the dealership would not offer a second repair under the recall.08/29/06the right rear stop lamp blub had to be replaced and both front wiper blades were replaced.
While driving on the freeway at 65 mph when the plastic piece in front of the windshield wipers broke loose and hit the windshield, and flipped over the vehicle. Consumer was able to pull over and out of traffic. The seven clip areas were completely abandoned.
Read more
