We found the following complaints for CHRYSLER ASPEN (2009)
Read complaints for CHRYSLER ASPEN (2009)
Takata recall. The contact owns a 2009 chrysler aspen. The contact received notification of nhtsa campaign number: 16v352000(air bags); however, the part to do the repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure.
The contact owns a 2009 chrysler aspen. The contact received a recall notification for nhtsa campaign numbers: 16v352000 (air bags) and 16v947000 (air bags). The parts needed were not available to perform the recall repair. The manufacturer was not notified. The contact had not experienced a failure. Parts distribution disconnect.updated 03/07/17*lj
Takata recall. The contact owns a 2009 chrysler aspen. The contact received notification of nhtsa campaign number: 16v352000 (air bags). The part to do the repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The contact had not experienced a failure.
I received and responded to a recall notice in july 23, 2016.to date, they still have not contacted me for repair.what are my options?
The overhead control module has failed 3 times in the last 2 years.we are being asked to cover it our of pocket again even though the part should be under the 12 month warranty.chrysler customer service tells me that since it was replace under warranty the last time (12 months ago) our consumer warranty goes back to the one we purchased the first time it failed and won't cover it this time.
I'm having several issues. First, i cant fill my gas tank up all the way, if i do my truck will shut off at any given time. Also my dash board lights don't work. I was told the bulb is sautered to the dash and the whole dash has to be replaced, that's $1300!currently, my major issue is, my truck not starting!!! i have replaced, the starter, the battery, the battery cables, and recently the alternator! i often need to get a jump and it usually turns over and will run for a day or two before needing a jump again! i have read reviews about this vehicle, and soo many of us are having the same issue. I think chrysler should do a recall concerning this matter and keep a good quality standard rating with the people that trust in their name!
Fuel pump short circuit. After pumping gas the truck will not turn on. Short circuit from the pump to the starter. After turning the key to power on the truck all the gas spilled from underneath.i drove to my kids school at 230pm , after leaving powered on the truck to roll the window down and thats when all the gas spilled from underneath.
Chrysler has a major problem with their 5.8 hemi engine.12/16/2020 i paid $3791.07 to replace a bad camshaft and lifters on a vehicle with only 72,768 miles. After researching this problem, i find hundreds of others having the same issues!in contacting chrysler, they of course, refuse to accept any responsibility for this design flaw. Although this is not a safety issue, it is a major engine defect which needs to be addressed. I would be interested if anyone else has expressed their concerns about this problem and chrysler'scomplete disregard.
Description to be sentby email immediately following this transmission. Description email will bear this temporary file number. On a weekday sometime in may 2014, i stopper at a stop sign, without he engine fully heated up, turned the wheel over to make a left turn and pressed the accelerator pedal.despite the fact that i had depressed the accelerator pedal, approximately 5% of travel, the engine remained at the standard 650 rpm curb idle speed. Holding my foot at that position, the engine remained at curb idle for approximately three seconds. The red throttle control lightening bolt illuminated on the instrument panel. Engine operation was otherwise normal. After about three seconds, the engine increased speed normally, the red light went off and i drove off without further malfunction. The check engine light did not illuminate at any time. At some point, in june 2014. The same malfunction occurred again. When opening the throttle from a standing start, the engine refused to respond to the throttle and remained at curb idle for approximately three seconds. The red throttle control light remained on for approximately three seconds, and the engine then resume normal operation. Again, the check engine light did not illuminate. For months, there was a very mild low rpm flat-spotting symptom. Specifically, once the car was in motion, small openings of the throttle produced only very mild acceleration, without hesitation. Pushing the throttle down a little further produced normal acceleration without a downshift. On july 19, 2014,i left the dealership and pulled out onto a feeder road. I noticed the flat-spotting again on the throttle opening at low rpm. I pulled into a parking lot, put the car in park and turned off the engine. I turned the key to on and once again followed the slowly depress fully calibration procedure. This procedure involved fully removing my foot from the pedal, at the end of the procedure. I turned the key off and then re-started the car. Instantly upon firing, the engine went to a 4000 rp
I just purchased the vehicle from the dealer and as i am fueling it for the first time fuel burped up and spilled all along the side. The fuel came pouring out of the tank and spilled over the side of the vehicle into the ground. This emitted a strong gas odor and at the same time produced a spill all around. I stopped fueling the vehicle, however i noticed that i was only able to fill about 3/4 of my tank. I have found many other comments and even videos on you tube of other durango /aspen drivers having the same issue. Please advise.
The fuel spits back when tank is full and spills out on car and on floor. This has happened on multiple occasions. I called chrysler as it is a known problem and they advised it will not be covered under extended warrant or a recall.
The contact owns a 2009 chrysler aspen. After refueling the vehicle, the contact began to drive and almost immediately the vehicle stalled. The contact was able to restart the vehicle. The contact, who was a certified mechanic, diagnosed the vehicle. The contact also confirmed with ourisman chrysler dodge jeep ram of bowie (located at 2406 crain hwy, bowie, md 20716, (855) 822-3228) that the check valve needed to be replaced. The vehicle was not repaired. The contact stated that the failure was more prominent after the vehicle was filled with fuel. The manufacturer was notified of the failure. The approximate failure mileage was 189,000.
I currently own a 2009 chrysler aspen hybrid. Today while fueling my vehicle i experienced the same problem i have been having since i purchased the vehicle about 3 weeks ago. As i am fueling the fuel trigger shuts off on me constantly. As i take it out to reinsert it, it spits out fuel at me. Once i am done fueling and proceed to cap the tank it spits fuel at me as well. Today i was drenched in fuel because as i began fueling my vehicle which had an empty tank it started to spit fuel back at me. This is not only hazardous to the environment but it?s also a personal safety hazard. I had to return home to change because my pants where covered in fuel. As i started to look for facts i noticed that i am not alone. Apparently this is a common issue amongst the durango/aspen models but nothing has been done. I ask you to please look into this issue. Today no one was injured or hurt but if i were to go anywhere after fueling and be exposed to any open flame i can almost assure you that my clothing would have caught on fire all due to a malfunction on these vehicles. I have included below four of a few links that have other individuals whom have or are experiencing the same issue. Please advice. Http://www.alldeaf.com/auto-talk/109865-extended-warranty-dodge-durango-fuel-check-valve.htmlhttp://www.safetyresearch.net/2011/03/23/fuel-spit-back-continues-to-plague-chrysler-vehicles/http://www.arfc.org/complaints/2007/chrysler/aspen_4x2/fuel_system_gasoline/problem.aspxhttp://www.faqs.org/car/chrysler-aspen-4x4-2007/fuel_propulsion-system/
I'm having several issues. First, i cant fill my gas tank up all the way, if i do my truck will shut off at any given time. Also my dash board lights don't work. I was told the bulb is sautered to the dash and the whole dash has to be replaced, that's $1300!currently, my major issue is, my truck not starting!!! i have replaced, the starter, the battery, the battery cables, and recently the alternator! i often need to get a jump and it usually turns over and will run for a day or two before needing a jump again! i have read reviews about this vehicle, and soo many of us are having the same issue. I think chrysler should do a recall concerning this matter and keep a good quality standard rating with the people that trust in their name!
Fuel pump short circuit. After pumping gas the truck will not turn on. Short circuit from the pump to the starter. After turning the key to power on the truck all the gas spilled from underneath.i drove to my kids school at 230pm , after leaving powered on the truck to roll the window down and thats when all the gas spilled from underneath.
My husband's truck and my aspen are both affected by the n08 recall for rear axle pinion nut.we received the first notice of this recall several months ago, but the notice told us that the parts needed for repair were not available and that we would receive a second notice when they were.we have now received the second notice and i have called our local dealer, southern chrysler dodge jeep, in lufkin, texas two times but they only had 3 or 4 of the parts come in and those are already promised to other customers.my husband and i are driving around in these vehicles with our 6 year old son, and no one is able to tell us when we might be able to have this fixed because they do not know when they will receive another shipment and each future shipment will most likely only be 3 or 4 parts.i would like to have the parts shipped to our dealership, reserved in our names, with instructions for them to contact us upon arrival. (2010 dodge ram 1500 & 2009 chrysler aspen), or they can be shipped to us directly.
The vehicle was parked outside. Probable transmission issue. The vehicle was in park. I started the vehicle using the remote start and the vehicle lurched forward several inches then settled back were it was. The outside temperature had been +- zero for several days. It did not repeat after being warmed up. It has never happened before. 116,000 miles.
Chrysler case #: 29959728vehicle description: chrysler aspen limited 4x2 sport utility 4-door i attempted to reach out to my case manager haley and my link has been disabled and her voicemail has yesterday's date. I have not received a call today from anyone at chrysler corp regarding my case. I did speak today with mopar vehicle protection and they stated when chrysler placed the max care coverage on my aspen, they were suppose to place the powertrain wrap with the max care coverage. Per my vehicle info and the sales rep, chrysler lifetime powertrain warranty was included with my vehiclepurchase. I have spoken with jake and meka also with regards to this case and was advised by meka, my case manager should be contacting me back. Seeking assistance since haley x40612 is not in the office.
The contact owns a 2009 chrysler aspen. The contact stated that nhtsa campaign number 13v038000 (power train) had exceeded a reasonable time for repair. The recall notification was received by the contact several months ago. The dealer was contacted and advised that they were unable to obtain the part from the manufacturer. The contact had not experienced a failure.
Description to be sentby email immediately following this transmission. Description email will bear this temporary file number. On a weekday sometime in may 2014, i stopper at a stop sign, without he engine fully heated up, turned the wheel over to make a left turn and pressed the accelerator pedal.despite the fact that i had depressed the accelerator pedal, approximately 5% of travel, the engine remained at the standard 650 rpm curb idle speed. Holding my foot at that position, the engine remained at curb idle for approximately three seconds. The red throttle control lightening bolt illuminated on the instrument panel. Engine operation was otherwise normal. After about three seconds, the engine increased speed normally, the red light went off and i drove off without further malfunction. The check engine light did not illuminate at any time. At some point, in june 2014. The same malfunction occurred again. When opening the throttle from a standing start, the engine refused to respond to the throttle and remained at curb idle for approximately three seconds. The red throttle control light remained on for approximately three seconds, and the engine then resume normal operation. Again, the check engine light did not illuminate. For months, there was a very mild low rpm flat-spotting symptom. Specifically, once the car was in motion, small openings of the throttle produced only very mild acceleration, without hesitation. Pushing the throttle down a little further produced normal acceleration without a downshift. On july 19, 2014,i left the dealership and pulled out onto a feeder road. I noticed the flat-spotting again on the throttle opening at low rpm. I pulled into a parking lot, put the car in park and turned off the engine. I turned the key to on and once again followed the slowly depress fully calibration procedure. This procedure involved fully removing my foot from the pedal, at the end of the procedure. I turned the key off and then re-started the car. Instantly upon firing, the engine went to a 4000 rp
As requested by jake - chrysler corp, cc#: 29959728 i took my car in for repairs last thursday. Matt richardson called on friday stating that the rear end barrings have come apart on the car and that they not only need to replace the barrings, they need to do an entire overhaul of the entire rear end. He explained they will be replacing the pinion nut which was the n08 recall performed last year, the differential unit including replacing the oil in the rear differential unit on the service that was performed in july 2016. He stated that it would take approximately 3 to 4 days. $1150 chrysler's lifetime powertrain warranty should cover this as the pinion nut, rear end differential is part of the powertrain. A warranty that provides protection for as long as you own the car to the key component groups that are essential to keeping your vehicle running: the engine, transmission/transfer case/all-wheel drive assembly, and drivetrain assembly. However, i am being charged. Recall #2 not performed as airbag parts are not available.
I had trouble with a humming noise and popping under my vehicle for a few months. The humming got so loud that we could not hear each other talk to one another at all. It popped pulling out, going around a curve, going backwards, or slowing down. The humming stopped all of a sudden after it got very loud. My aspen then fell toward the right side and smoke started shooting out from the passenger back tire when driving it. I then took it to the mechanic. He said it was very bad. The rear axle and rear axle bearing are destroyed and it will need a new rear end. This vehicle had no8 rear pinion nut recall completed on 1/13/2014. If the recall really solves the 2009 aspen problem of the rear end axle and axle bearings from being destroyed then why am i now having to get a new rear end in december of 2019. I see complaints all over the internet about this problem with the vehicle after the recall was completed so now people are paying for repairs out of pocket.a $2500+ repair for a vehicle is an awful product flaw that chrysler is not being responsible for. I have had cars for 20 years that i never had to pocket money like that for all their repairs together.
I filed a complaint about the pinion nut and rear bearings issue to the nhtsa pinion nut recall - n08 - power train/driveline/differential unit.while stateline chrysler representative, matt richardson, does not feel that the issue is related to the pinion nut recall, i strongly disagree. The reason stated for the when i press the gas that my car makes noise which appears to be coming from the front, but is actually coming from the rear, is because this is related to the rear end differential unit. Fact #1 ' my aspen is 1 of the 11 million vehicles affected built by fca and part of the 2015 nhtsa enforcement action. Fact #2 - stateline chrysler, fort mill, sc handled the recall for the pinion nut repair. Fact #3 ' july 2016, i was advised my car need pinion nut repair after the pinion nut repair service had been performed. Fact #4 ' during the same service, i was advised there was no rear differential fluid in my car by chrysler and that it needed to be sealed. Which means my car's differential unit has not been lubricating. Fact #5 ' i was advised by chrysler that the noise would go away after i paid to have oil 'put into' the rear differential unit. I called matt to advise the noise had not gone away. On the third week, i took my car in and was advised the rear bearings need to be replaced at the cost of $2000.00. Fact #6 ' i was advised by matt richardson my car will lock-up while driving.the failure happened at chrysler which has impacted the way my car drives and my safety. This is truly 100% related to the n08 recall. Fca is accountable for its past failures and has committed to get unsafe vehicles repaired or off the roads, i did not receive any letter as agreed to by a consent order july 2015 with nhtsa, as fiat chrysler agreed.
Have taken car in to chrysler dealership with regards to noise. Car making whinin noise while driving. Initially advised rear pinion seal leaking. So no fluid in rear differential unit. I stated rear pinion nut was a recall and if nut had been replaced, how any why did fluid leak out? rear differential service performed and fluid added with service at my expense. Advised noise would go away. Took car in again almost three weeks later, as patiently waited for noise to go away, now told rear differential carrier bearing are worn and $2000 to fix car! all of these rear differential failures are the fault of the rear differential pinion nut.
The contact owns a 2009 chrysler aspen. The contact stated that another vehicle crashed into the rear of the vehicle. Upon impact, the passenger's side rear seat belt failed to engage and caused the passenger's head to strike the seat. The passenger sustained a concussion and whiplash. A police report was not filed. The vehicle was taken to the dealer where the failure could not be diagnosed. The manufacturer was contacted about the failure. The failure mileage was 45,900.updated 7/9/14the consumer stated the passenger continued to experience on-going headaches. Updated 07/11/2014
Have taken car in to chrysler dealership with regards to noise. Car making whinin noise while driving. Initially advised rear pinion seal leaking. So no fluid in rear differential unit. I stated rear pinion nut was a recall and if nut had been replaced, how any why did fluid leak out? rear differential service performed and fluid added with service at my expense. Advised noise would go away. Took car in again almost three weeks later, as patiently waited for noise to go away, now told rear differential carrier bearing are worn and $2000 to fix car! all of these rear differential failures are the fault of the rear differential pinion nut.
Description to be sentby email immediately following this transmission. Description email will bear this temporary file number. On a weekday sometime in may 2014, i stopper at a stop sign, without he engine fully heated up, turned the wheel over to make a left turn and pressed the accelerator pedal.despite the fact that i had depressed the accelerator pedal, approximately 5% of travel, the engine remained at the standard 650 rpm curb idle speed. Holding my foot at that position, the engine remained at curb idle for approximately three seconds. The red throttle control lightening bolt illuminated on the instrument panel. Engine operation was otherwise normal. After about three seconds, the engine increased speed normally, the red light went off and i drove off without further malfunction. The check engine light did not illuminate at any time. At some point, in june 2014. The same malfunction occurred again. When opening the throttle from a standing start, the engine refused to respond to the throttle and remained at curb idle for approximately three seconds. The red throttle control light remained on for approximately three seconds, and the engine then resume normal operation. Again, the check engine light did not illuminate. For months, there was a very mild low rpm flat-spotting symptom. Specifically, once the car was in motion, small openings of the throttle produced only very mild acceleration, without hesitation. Pushing the throttle down a little further produced normal acceleration without a downshift. On july 19, 2014,i left the dealership and pulled out onto a feeder road. I noticed the flat-spotting again on the throttle opening at low rpm. I pulled into a parking lot, put the car in park and turned off the engine. I turned the key to on and once again followed the slowly depress fully calibration procedure. This procedure involved fully removing my foot from the pedal, at the end of the procedure. I turned the key off and then re-started the car. Instantly upon firing, the engine went to a 4000 rp
Read more
