We found the following complaints for CHRYSLER 200 (2012)
Read complaints for CHRYSLER 200 (2012)
The contact owned a 2012 chrysler 200. While the contact's granddaughter was driving 10 mph and making a left turn, another vehicle crashed into the front passenger side. The air bags failed to deploy and the driver side seat belt failed to restrain the driver, which caused her head to hit the steering wheel. The driver sustained bruising to the forehead, but medical attention was not required. The front seat passenger was uninjured. A police report was filed. The vehicle was driven to a local auto body shop where it was deemed a total loss. The contact received notification of nhtsa campaign number: 16v668000 (air bags, seat belts) several months prior to the failure. The dealer and manufacturer were not notified as the recall notice stated that owners would receive a second notice when remedy parts become available. The failure mileage was 80,566.
Air bag warning light illuminates.dealer states it may be a bad connection under the seat. No action taken except checked said connection, all connections free from debris and corrosion, and secure. Failure indicated around 76,000 miles. Not diagnosed or repaired. Airbag warning light continues to illuminate. Current mileage: 99,580.
Vehicle was recalled ten months ago (16v-668). Parts are still not available. Local chrysler dealership is stating parts will not be available until 2018. Make chrysler fix this safety concern!
Transmission rebuild and three torque convertors in 6 moheater warm on left cool on rightengine stalls on highwayheat worked when taken to draler.they replaced sa clicking blend door actuatorin the morning there was warm air on the left and cool air on the right'dealer says need a heater core and radiator.this happened overnight?recall onairbags.no airbag light on at dealer,they flashed the tipm as per recall,now airbag light is on code reads replace occupant controle module.they claim this not on the recall,11v315000
On june 21st, 2020 i was at a red light when a van hit me in the rear and my airbags did not deploy. Me and my wife and kids were in the car and injured. I got taking to the hospital right away and my rest of my family went after i was taken in.
Takata recall. The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (seat belts, air bags); however, the parts to do the repair were unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The vehicle was taken to the local dealer (sheets chrysler dodge jeep ram located at 250 auto plaza dr, beckley, wv 25801; (304) 252-4555) where it was confirmed that the parts were not available for the recall remedy. The manufacturer was not contacted. The contact had not experienced a failure. Vin tool confirms parts not available.
2012 chrsler 200.at29509 miles car taken in for transmission problems and leaks.torque convertor replaced.while there dealer addressed recal n38.reprogramed tpm.1may201511nov 2015 car was taken in because transmission would not shift.while there air bag light deployed.code reads occupant restraint control module.dealer refuses to replace under recall. Mileage52819.car will be in back for service today.after replacing torque convertor and transmission again it went three miles and wouldnt shift correctlyand again stalled on highway. Current issue:replace occupant restraint module under recall38.
The contact owns a 2012 chrysler 200. The contact stated that there was no failure with the horn operating until the vehicle was serviced for an unspecified manufacturer recall regarding the air bags. Months after the air bag recall was serviced by massey yardley jeep chrysler dodge ram (777 north state road 7, plantation, fl 33317, 954-327-4000), the horn failed to function properly and various warning indicators flashed on the instrument panel without warning. The contact was waiting for a response from the dealer to determine if they could duplicate the failure. The manufacturer was notified. The vehicle was not repaired. The approximate failure mileage was 46,000.
Mold inside passenger door and back left side door, every time it rains, water collects in the door and never comes out - causing mold to form. Car has never been wrecked and it was bought brand new
This car has a air bag sign in dasboard. 7-8 months ago there was a air bag recall for this car but the agency said it was for different part recall which means this car still has an airbag sign in dashboard. I am not sure when did the sign appear first time. One day i started this car and their was an airbag sign and it never disappear after that. *dt
Received a recall notice but no parts are available for a fix.been waiting about 6 months with no action.how do i get the company moving on providing corrective action?
The contact owns a 2012 chrysler 200. While driving approximately 45 mph, the contact crashed into the rear end of another vehicle. The driver sustained severe injuries to the right leg and ankle and also suffered from a cracked sternum. A police report was filed of the incident. The air bags failed to deploy with the impact. The vehicle was completely destroyed and towed to savage facility. The manufacturer was notified of the defect and planned to launch an investigation in regard to the faulty air bags. The approximate failure mileage was 850.
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (seat belts, air bags); however, the parts to do the repair were unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The contact called the dealer (meadowland carmel at (877) 752-7220) where it was confirmed that the parts were not available for the recall remedy. The manufacturer was not made aware of the issue. The contact was informed that owners would receive a second notice when parts become available in august of 2017. The contact had not experienced a failure. Vin tool confirms parts not available. Updated 08/09/17*lj
The contact owns a 2012 chrysler 200. The contact stated that the recall notice for nhtsa campaign number: 16v668000 (air bags, seat belts) was received in september of 2016. After contacting the manufacturer on multiple occasions, the contact was informed that the parts needed for the recall remedy were still not available and no estimated time for receiving the parts could be provided. The local dealer was not notified. The contact had not experienced a failure. Vin tool confirms parts not available.
Vehicle was involved in a side impact crash with a guardrail. Vehicle was traveling approximately 45 mph on an interstate highway when the passenger side struck the guardrail. No airbags deployed and my wife who was in the front passenger seat with her seatbelt on was injured on her entire right side.
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (seat belts, air bags); however, the part to do the repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The contact called a local dealer (carl burger chrysler jeep dodge ram world (8355 hercules st, la mesa, ca 91942) and was informed that the part to do the repair was not available. The manufacturer was not made aware of the issue. The contact had not experienced a failure. The vin was not available.
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (seat belts, air bags); however, the part needed for the repair was not available. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The vehicle was not diagnosed or repaired. The manufacturer was made aware of the issue. The contact had not experienced a failure. Vin tool confirms parts not available.
Takata recall. The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign numbers: 16v668000 (seat belts, air bags) and 17v640000 (air bags, seats); however, the parts to do the repair were unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The dealer (oliver c joseph chrysler dodge jeep, 3795 il-15, belleville, il 62226) was contacted and confirmed that the parts were not available for the recall remedy. The manufacturer was not contacted. The contact had not experienced a failure. Parts distribution disconnect.
Notification for recall 16v-668 with no solution involving pretensioner airbag deployment where airbags will not deploy was reported 2 years prior to official notification of recall 16v-668.this was due to a front-end crash in 2014 where there were two passengers and the airbags did not deploy.the crash involved a nose dive going approximately 40mph into a 2-story gully directly hitting a large oak tree with no airbag deployment.this crash and the airbags not deploying was reported to asheboro chrysler dodge jeep ram service department in 2014 with no solution or knowledge of issue.official notification was provided in december 2016 through the usps.
The contact owns a 2012 chrysler 200. The contact received notifications for nhtsa campaign numbers: 16v668000 (seat belts, air bags) and 17v640000 (seats, air bags); however, the parts needed for the repairs were not available. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repairs. The vehicle was taken to roberson motors (3100 ryan dr. Se, salem, or 97301, (503) 363-4117), but the parts were not available for the repair. The manufacturer was not contacted. The contact had not experienced a failure. Parts distribution disconnect.
Our airbag lights are on. We got notified by the dealership of the recall. But this matter regarding the wheel bearings is a serious matter. I've repaired my car 5 times all around the car. That's not normal. All of these vehicles have a similar issue in the rear end where when i'm driving and hit a bump, the rear end shifts left or right.
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (air bags); however, the part for the repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The contact had not experienced a failure. The manufacturer was notified. Parts distribution disconnect.
There was a recall on my vehicle i took it to the dealership in harrisonburg va to be repaired. They only fixed the active head restraints. My car failed a state inspection due to my airbag light illuminating. I have read that "certain" chrysler 200's 2012 they are to reprogram the tipm then replace the occupant restraint module if needed. They refused to replace this gave me an estimate of $400. I called chrysler and they also said my car was not recalled based on the vin and my issue. I am a single mother with two kids my car has 67,000 miles on it has never been wrecked or damaged and i believe chrysler should replace this. My car is only 4 years old an airbag should not become defective in 4 years. This exact issue is what other 2012 chrysler 200s have also. I am still unable to have my car pass a state inspection and i also informed chrysler that when passengers ride in that seat they are putting lives at risk by not acting quickly. It is dangerous and chrysler should recall all 2012 200's. It hey informed me the problem is in the dash i don't even feel safe driving my car what if my air bags don't deploy? i will live with that the rest of my life and chrysler should be held accountable for negligence. Just because my vin number doesn't match at this time or the time frame they claim the defects were installed doesn't mean the part they installed isn't defective. I hope you all take this matter very seriously. This is a safety issue that could take or save lives.
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (seat belts, air bags); however, the parts to do the repairs were unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The dealer confirmed that the recall remedy was not available. The manufacturer was not notified of the issue. The contact had not experienced a failure. Vin tool confirms parts not available.
Open connection in drivers headrest airbag
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (seat belts, air bags); however, the part to do the repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The manufacturer was notified of the issue. The contact had not experienced a failure. Vin tool confirms parts not available.
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (air bags, seat belts); however, the part to do the repair was unavailable the contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. An unknown chrysler dealer was contacted and stated that the parts were unavailable. The manufacturer was not made aware of the issue. The contact had not experienced a failure. Vin tool confirms parts not available. Updated 08/03/17*ljupdated 08/29/2017
Takata recall/air bags.i received notice of a recall (ca recall #s61) on 9/13/16.website is showing the replacement part is still unavailable as of today 2/11/17.i would think after five months the parts should be available.i'm very unhappy with this situation.
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (seat belts, air bags); however, the part to do the repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The contact inquired about part availability and was informed that owners would receive a second notice when the part becomes available, which may be in june of 2017. The contact had not experienced a failure.
The contact owns a 2012 chrysler 200. The contact received a recall notification for nhtsa campaign number: 16v668000 (seat belts, air bags); however, the parts to do the repair were unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repairs. The manufacturer was not made aware of the issue. The contact was informed that a second notification would be sent to owners in june of 2017. The contact had not experienced a failure.
"takata recall"as i was driving down highway. I heard a safety ding and i noticed my air bag saftey light was on. I took it to the dealership and told me it was to due the the airbag sensor and could not be fixed at this time. That was back in the beginning of the year. To date there is no remedy.
Takata recall. The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (air bags) and stated that the part was not available within a reasonable time frame to schedule the recall repair. The dealer did not give a specific date for when the part would become available so the contact was unable to determine when the vehicle would be repaired. The manufacturer was contacted and could not provide an estimated date for when the contacts vehicle would receive the recall repair.the contact was experiencing a failure in which there was an abnormal noise heard coming from the area near the air bags in the front of the vehicle. The failure mileage was not available.vin tool confirms parts not available.
The contact owns a 2012 chrysler 200. While the vehicle was parked, the front passenger side headrest air bag inadvertently deployed. The vehicle was taken to a dealer where it was not diagnosed. The contact was informed that the recall stated only to replace the module, not the headrest part. The contact received notification of nhtsa campaign number: 13v282000 (electrical system, air bags). The manufacturer was not notified of the failure. The failure mileage was approximately 75,000.
The contact owns a 2012 chrysler 200. The contact received a recall notification for nhtsa campaign number: 16v668000 (air bags); however, the parts to do the repair were unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The dealer dodge, jeep, chrysler of winter haven, florida was contacted and confirmed that the parts were not available for the recall remedy. The manufacturer was made aware of the issue and was not able to confirm when the parts were to become available. The contact had not experienced a failure. Vin tool confirms parts not available.
The contact owns a 2012 chrysler 200. The contact stated that the recall notice for nhtsa campaign number: 16v668000 (air bags, seat belts) was received in september of 2016. After contacting nhtsa, the contact was informed that the parts needed for the recall remedy were not available and no estimated time for receiving the parts could be provided. The dealer and manufacturer were not notified. The contact had not experienced a failure. Vin tool confirms parts not available.
Takata recall. The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (seat belts, air bags) however, the part to do the repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. Vin tool confirms parts not available.
Takata recall. The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (air bags); however, the part for the repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The contact had not experienced a failure. The manufacturer was made aware of the issue. Parts distribution disconnect.
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (seat belts, air bags). The part to do the repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The contact spoke to poulin chrysler dodge jeep ram (401 n main st, rochester, nh 03867) who stated that the parts were not yet available and they did not know when they would be available. The contact had not experienced a failure.
The contact owns a 2012 chrysler 200. The contact stated that the air bag warning light flashed for several months. The failure progressed and the air bag warning light remained illuminated. The vehicle was taken to the dealer but was not diagnosed or repaired. The vehicle was not included in nhtsa campaign number: 13v282000 (air bags, electrical system). The vin was not available. The manufacturer was notified of the failure. The approximate failure mileage was 50,000.ma 10/5
Takata recall. The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (air bags, seat belts); however, the part to do the repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The manufacturer was notified of the issue. The contact had not experienced a failure. Vin tool confirms parts not available.
I got into a car accident in may of 2016. My air bags did not deploy, as they should have given the speed i was going. I also was not notified of this recall until later that year. I have called and checked online to see when the parts would be in to have the recall issue solved and i have been told they do not have an eta and the parts aren't available.
On september of 2016, i received a recall notice stating that the potential loss of airbag and seat belt pretensioner deployment during a crash may increase the risk of injury.it also stated that when a remedy and parts were available, i would be notified.i have been driving this car for 7 months (probably for 5 years, since i purchased it new) without this needed protection, and there has been no notification yet.when can i expect chrysler to correct this problem?
The light of the air bigs is always light on when driving.i never had accident.
Re s61/nhtsa 16v-668 i had this condition and paid to have it repaired.chrysler (fca) has been telling me for almost a year that they will reimburse me for the repair as soon as they determine the needed part. They state that they still don't have an identified repair so i have to keep waiting for my refund.that is not timely resolution.
I received a recall notice months ago and have had not response to checking and or repairing recall parts and or no contact, i have registeredat recalls. Mopar. Com with no response to date (waiting months)
Its been several months now that i just recieved my safety recall notice and yet a dealership has not repair any of the recalls. Please address this asap before an accident does occur. Thank you
I received a recall notice in 11/2016. According to auto nation chrysler in phoenix, the part has not yet been produce nor available for replacement. How much longer am i forced to drive an unsafe car?
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (seat belts, air bags); however, the part to do the repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. The vin was not available.
Took my car in for airbag safety recall and the work was done.later my airbag light came on and i was told that it was unrelated to the recall but a defective connection for my head restraint airbag was out and it would cost $531 dollard to fix.what a coincidence.now my headrest air bag is non-functioning and the light remains on.this happened at jeep chrysler in san leandro,ca. On marina blvd.
The contact owns a 2012 chrysler 200. While driving, the seat belt warning indicator illuminated. The vehicle was taken to the local dealer (bill luke chrysler jeep dodge and ram located at 2425 w camelback rd phoenix, az 85015) where it was diagnosed that the seat belt module needed to be repaired. The manufacturer was made of the failure and placed the contact on the fast track system where they would reach out to him when the remedy was available. The contact paid for the repair and requested reimbursement. The failure mileage was 50,000.
I was driving home from work and i was coming down a side street and i saw this u haul van going a high rate of speed at least 35 - 40 mph (the posted speed is 15 mph) and it hit me on the passenger side and pushed me into a tree and while hitting the tree my airbags did not go off and i was hurting at that time, i was taken to the nearest hospital and released and when i went to the dealer and told them what was going on they said its not their problem that i would have to take it up with the manufactor and i did, but like ususal they said they did no wrong their car is up to par but as i read on their website that the airbag is suppose to go off during a side impacted and i am very upset that this happen to me and my car has been sitting and getting worked on since sept. 6, 2012 and there was a part to my car that was on back order which i am shocked when its a brand new car.i am having the worst time with this whole thing and it seems like no one cares that i got hurt or that i am having so many problems with the car, the insurance and many other things can some one please take a look into my case and help me i can't take anymore ......................i can't or there isn't or sorry for your inconvience i am going crazy.
I've been notified for sometime now about a recall for my car. Nothing has been corrected yet in reference to the airbag and seat belt -constraint controls. What happens if i have an accident with these features still not corrected?
I was driving straight forward, in the right lane of a four lane highway (two lanes in either direction). A car traveling in the opposite direction, lost control and crossed the highway, striking my car's front end. My car received extensive front end damage. The car was totaled, as was the other car. I was driving and my wife was in the front passenger seat. We were both wearing our seat belts. At the time of the impact, neither airbag deployed, nor did the seat belt pretensioners activate (locking the seat belts in place), causing serious injury to both of us, requiring hospital admittance in the intensive care unit, for myself. Police traffic crash report, photos and other documents are available if required, in the future. Also, i just received a re-call notice, dated october 1, 2016. Nhtsa 16v-668, concerning the car i was driving at the time of the crash...updated 01/04/17 *po - inj but not death as indicatedupdated 7/25/18*dt
The contact owns a 2012 chrysler 200.the contact stated that while driving 25 mph, she was rear ended and the air bags failed to deploy.no warning lights illuminated on the instrument panel.the driver's head struck the steering wheel and as a result, the contact sustained tooth trauma and back injuries that required medical attention. A police report was filed.the manufacturer wascontacted.there was no diagnosis completed on the vehicle.the failure mileage was 26,000 and the current mileage was 27,000. Updated 06/22/15.
"takata recall" my air bag light is on in the dash board my car was already at the dealership for another issue the agent informed me the airbag modular has failed i informed the agent there is a recall for the tipm.a defective tipm can causeair bags not to inflate and other major issues.the dealership want to charge me 429.00 to fix.
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16668000 (air bags, seat belts); however, the part to do the repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. Beaver toyota of saint augustine was contacted about the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. Vin tool confirms parts not available.
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (air bags, seat belts); however, the part to do the repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The dealer and manufacturer were not made aware of the issue. The contact had not experienced a failure. Vin tool confirms parts not available.updated 08/24/17*ljupdated 09/20/2017
The contact owned a 2012 chrysler 200. While the contact's partner was driving 25 mph, the driver crashed into a wall to prevent rear ending another vehicle. The driver sustained injuries to the back and neck, which required medical attention. The air bags failed to deploy. A police report was filed. The vehicle was towed from the scene and confirmed destroyed. A dealer was not contacted. The manufacturer was not made aware of the failure. The vin was included in nhtsa campaign number: 16v668000 (seat belts, air bags), but the vehicle had not been serviced. The approximate failure mileage was 147,000....updated 10/17/17 updated 9/5/18
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (seat belts, air bags); however, the parts to do the repair were unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The lake shore dealer was contacted and confirmed that the parts were not available for the recall remedy. The manufacturer was not made aware of the issue. The contact had not experienced a failure. Vin tool confirms parts not available.updated 09/07/17*lj
The contact owns a 2012 chrysler 200. The contact stated that she received notification of nhtsa campaign number: 13v282000 (air bags , electrical system) and stated that the parts were not available. The contact also mentioned that the air bag warning light illuminated two weeks sporadically. The vehicle was neither diagnosed nor repaired. The failure mileage was not available.
I keep getting airbag icon airbag error message. I was instructed by insurance to run vin to see if there has been a recall upon running vin i was notified there was 3 recalls listed for vin.
The contact owns a 2012 chrysler 200. The contact stated that the air bag warning light illuminated intermittently. The vehicle was not diagnosed or repaired. The manufacturer was notified of the failure. The approximate failure mileage was 60,000.
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (air bags, seat belts). The part to do the repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The dealer and manufacturer were not contacted. The contact had not experienced a failure. Vin tool confirms parts not available. The consumer stated the vehicle was repaired.
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (seat belts, air bags); however, the parts to do the repair were unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The dealer was not contacted. The manufacturer was contacted by email at [email protected] and confirmed that the parts were not available for the recall remedy. The manufacturer was made aware of the issue. The contact had not experienced a failure. Vin tool confirms parts not available.
Takata recall.i have a recall on airbags and seatbelt transponder may not work in event of an accident.i refuse to drive this car and am not waiting until june 2017 for a repair.i want a buyback immediately....with incentive ...so i can get on with my life.a rental is being offered at this time .i am not satisfied and a buyback would make more sense.
The contact owned a 2012 chrysler 200. While driving 45 mph, the contact lost control of the vehicle. The vehicle rolled a few times and struck several trees. The air bags failed to deploy. A police report was filed. There were minor injuries, which did not require medical attention. The vehicle was destroyed. The manufacturer was not notified. The approximate failure mileage was 40,000.
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (air bags, seat belts); however, the part for the recall repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The contact had not experienced a failure. The manufacturer was not made aware of the issue. Vin tool confirms parts not available.
My car has 42k miles. Air bag light is on. Second issue is a clunking noise in left front wheel and can be felt in steering wheel while in motion.
Takata recall - i never received any information regarding this recall.i am just now (july 2016) experiencing the airbag warning light coming on and a warning tone being emitted randomly while i'm in motion.i'm interested to know if i can still take my car to the dealership to have it worked on under n38 13v282?
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign numbers: 13v282000 (air bags, electrical system) and 16v668000 (air bags, seat belts) however, the parts to do the repairs were unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repairs. The manufacturer was made aware of the issues. The contact had not experienced a failure. Vin tool confirms parts not available and parts distribution disconnect.
The contact owns a 2012 chrysler 200. The contact stated that within two weeks of owning the vehicle, the head rest restraint deployed without warning. The vehicle was included in nhtsa campaign numbers: 13v282000 (electrical system, air bags), 16v668000 (seat belts, air bags), and 17v640000 (seats, air bags). The dealer (autonation usa corpus christi, 3115 s padre island dr, corpus christi, tx 78415-1815, 361-217-6733) was notified of the failure. The vehicle was not repaired. The manufacturer was notified of the failure. The approximate failure mileage was 52,000.
The contact's spouse owns a 2012 chrysler 200. While the contact's spouse was driving 45 mph, her vehicle was cut off by another vehicle and crashed into a wall. The air bags failed to deploy. The contact sustained injuries to the c3/c4 cervical vertebrae and a laceration to the knee, which required medical attention. A police report was filed. The vehicle was towed to an independent facility. The vehicle was repaired; however, the contact was concerned that the air bags were never replaced. The vehicle was included in nhtsa campaign number: 16v668000 (seat belts, air bags). A dealer was not contacted. The manufacturer was notified of the failure. The approximate failure mileage was 64,000.
I received a letter back in january that a vehicle i own has a safety recall of "loss of airbag and seat belt pretensioner deployment capability during a crash. I emailed them back in february and was told i needed to wait they would get back to me as soon as possible, i emailed again in april was told the same thing it is now august. My son drives this car, would they be so laid back if it was one of their family members ?i would appreciate it, if you could tell me how i can take this further. Thank you
Recall was issued in september 2016, for;"vehicles may experience loss of air bag and seat belt pretensioner deployment capability in certain crash events due to a shorting condition resulting in a negative voltage transient that travels to the occupant restraint controller via the front impact sensor wires."it is now july 2017, without an estimated repair time nor when or how the situation could be fixed.
Takata recallunknown my car stalled out on the side of the road and i left it there to be picked up by my mechanic the next morning. I found out the next day that my car had been crashed and i went to the tow yard where the vehicle had been taken to retrieve my personal items from the vehicle and noticed that my airbags did not deploy. My car has been considered a total loss by geico car insurance. Geico claim number [xxx]. I still have my title, it is a rebuilt one. Geico has been taking their sweet time to reimburse me for my vehicle. The actual accident occurred on april 25th, 2017. The police report is inaccurate. Today is august 30th, 2017 and i'm still waiting on a check. The tow yard has apparently become the lienholder so i've been told and geico has to pay them off before they can pay me? i don't know it's crazy. There would be no lien if geico had handled this in a timely manner. I have had to come out of pocket to purchase a cheap car in the meantime while i wait. I have just recently received emails from carfax saying that my car may be at risk of being recalled so i put in my vin number ([xxx]) and it says that my chrysler 200 2012 is a s61. However, i was aware the passenger seatbelts were locked but i was still able to wrap the driver's belt around me. Furthermore, i've had numerous headlight issues in both headlights and the ac eventually stopped working. There was also a check engine light on that could not be turned off. I spoke with chrysler and they told me nothing can be done as far as reimbursement at this point because i have no possession of the vehicle. However, the title is still in my name and the possession issue is geico's fault. I am looking for some type of justice in this situation it could have been me in the crash. I am [xxx]and it says under federal law that my vehicle can be replaced. #16v-668information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6).
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (seat belts, air bags); however, the part to do the repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair the manufacturer was notified of the issue. The vin was unknown. The contact had not experienced a failure. Vin tool confirms parts not available. Updated 01/25/17. Updated 03/03/17*lj
The contact owns a 2012 chrysler 200. The contact received a recall notification for nhtsa campaign number: 16v668000 (air bags); however, the parts to do the repair were unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The dealer (east hartford chrysler/jeep/dodge of hartford, connecticut) was contacted and confirmed that the parts were not available for the recall remedy. The manufacturer was made aware of the issue and was not able to confirm when the parts would be available. The contact had not experienced a failure. Vin tool confirms parts not available.
My seat pops out sometime when driving. It happens anytime whether in motion or stationary hence the airbag light is on.
The contact owns a 2012 chrysler 200. The contact stated that the air bag sensor warning light illuminated. The vehicle was not diagnosed nor repaired. The manufacturer was not mad aware of the failure. The approximate failure mileage was 75,000.
I had safety recall on active head restraints,i received a notice and i proceed to take my car to my closest dealership,they told me the tipm was reprogram,new orc module was installed and s61 occupant restraint controlled recall. They told me my car was ready to pick up. But i still have the same problem. I asked why my airbag light was on and they stated my car can be check again but they are going to charge me 125 dlls only for the diagnosis,parts and laborwill be charge separately, i cannot pay for that, and i am worried about the safety of me and my family. Would you please help me.give me any options. At the time of this happen my car was park in my house. The next day when i was ready to go to work the airbag light turn on.please help me . Thank you
Takata recall. The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (air bags) and stated that the part was not available within a reasonable time frame to schedule the recall repair. The interim recall notification letter did not give a specific date for when the part would become available. The manufacturer could not provide an estimated date for when the contact's vehicle would receive the recall repair. The contact was not experiencing a failure. Vin tool confirms parts not available. Updated 04/05/17*lj
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (seat belts, air bags). The part needed for the repair was not available. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The vehicle was taken to paulding chrysler dealer (located on 1246 old griffin rd, dallas, ga 30157), but the part was not available for the repair. The technician at paulding chrysler informed the contact that there was no remedy and to wait for a second recall notice. The manufacturer was made aware of the issue. The contact had not experienced a failure. Vin tool confirms parts not available.
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (seat belts, air bags). The part to do the repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The contact spoke to a dealer who was unaware of the recallthe manufacturer was not made aware of the issue. The contact had not experienced a failure. Vin tool confirms parts not available. Updated 07/11/17*lj*as
The contact owned a 2012 chrysler 200. While driving 45 mph, the contact crashed into two cows. The air bags did not deploy. A police report was filed. The contact sustained injuries to chest area, which required medical attention. The vehicle was destroyed and towed. The vin was included in nhtsa campaign number: 16v668000 (air bags, seat belts). The manufacturer was not notified of the failure. The failure mileage was approximately 79,000.
2012 chrysler 200. Consumer writes in regards to airbag recall. *ld
My car engine is knocking loud when i drive, do i need a new engine..?
Air bag light is on , going threw brakes and tires every 6 months sense i bought it in 2016. Also no heat started at passanger side and worked its way towards drivers side. Also front windows do not go down started passanger side and 3 months later no driver side. Also was driving about 35 mph made right hand turn car has stalled 5 times.
I bought my car brand new in 2012 from chryaler dodge and jeep in springfield pa. I babe around 96,000 miles on my car and this will now be the third alternator that has been put in my vehicle. From what i know, the alternator should last up between 80,000 to 100,000 miles. I believe there has to have been a defect with my specific car. Along with some of the other recall items i am now reading about with my model, having kids, i am increasingly concerned about my health andsaftey driving this vehicle. I want to know what can be done about this on your end
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign numbers: 16v668000 (air bags) and (seat belts); however, the part to do the repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. Vin tool confirms parts not available.
Took car in to dealership years ago to have head rest and airbags fixed. Received a notice by inputting my vin that these fixes were incomplete . Also discovered that the 3.6 pentastar engine from the factory had substandard engine bearings which could result in the engine seizure and the remedy was for the factory to replace the engine. My 2012 chrysler 200 was manufactured during this time frame, yet was never notified by the manufacturer of this dangerous condition.
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (air bags, seat belt); however, the part for the recall repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The contact stated that the air bag warning indicator illuminated. The approximate failure mileage was 70,000. The manufacturer was not made aware of the failure. Vin tool confirms parts not available.updated 05/04/17*lj
Airbag sensor light keeps coming on intermittently.i took to dealership,they said would be fee for doing sensor check.we called chrysler dealership and they said it was not under recall.i took to advance auto and they ran a sensor check for free for me and they said there were "zero" issues or problems which is not right because the light and dinging come on intermittently every few minutes when driving.what is strange is that it only happens when my husband is driving the car.when i drive it, it doesn't happen.the lady at the dealership said it was strange, but that the transmission recognizes different people driving and tries to adjust for it and maybe that was it?the other dealers said that was something they'd never heard of.meanwhile, they say there is nothing they can do if there is no sensor light appearing when i take it in, or not showing up on the error report from the scan.so, i am stuck with driving a car that constantly dings, lights come on, and when i read the manual it said "take to the dealership immediately if this happens!".it is scary, especially when i have my children and grandchildren in the car, to worry whether my airbag is going to explode at any given time without notice.i would sincerely request chrysler take care of this issue.
On nov 7 2016 at roughly 7pm, i was heading west on the 10 freeway location 34.065990,-117.993771, baldwin park, ca. Traffic started to slow to 45 mph then came to a sudden stop and i was the last one in the 4 car collision. My airbags did not deploy and. I feel that the brakes may be faulty for when i stepped on them as hard as i could it seemed to be more of a skipping stop. For the littlest bump feels like ur hydroplaning to a stop. Chrysler never informed me of any recall about the airbags though i felt they should of deployed. My car was in the shop till march so i havent had it back but a few months.
The contact owns a 2012 chrysler 200. The contact stated that the air bag warning light remained illuminated and the horn randomly sounded without warning. In addition,the vehicle randomly stalled numerous times. A pass time failure occurred and the dealer rewired the vehicle. A mechanic indicated that the tipm was faulty and may need to be replaced. The mechanic suggested that the vehicle be taken to the dealer for further inspection. The dealer was notified of the failure and the contact was uncertain as to why they indicated that the orc module needed to be replaced, but did not verify if the vehicle was included in nhtsa campaign number: 13v282000 (air bags and electrical system). The vehicle was not repaired. The contact was to check with the manufacturer to determine a repair solution for the vehicle. The approximate failure mileage was 89,444.
The contact owns a 2012 chrysler 200. While operating the vehicle, the air bag warning indicator remained illuminated. The vehicle was taken to militello motors (1029 n. State st, fairmont, mn) where it was diagnosed that the driver's side head rest air bag was faulty and needed to be replaced. The vehicle was not repaired. The manufacturer was not notified. The vin was not available. The failure mileage was 77,000.
The contact owns a 2012 chrysler 200. While driving 10 mph, the tire pressure gauge malfunctioned, the seat belt warning indicator illuminated, and the air bag warning indicator illuminated. The warning indicators functioned normally after 20 minutes, but the air bag light remained illuminated and a tipm warning indicator flashed. The vehicle was not diagnosed or repaired. The vin was excluded from nhtsa campaign number: 13v282000 (air bags, electrical system). The failure mileage was approximately 70,000.
The contact owns a 2012 chrysler 200. The contact stated that while driving 11 mph another vehicle crashed into the contact which caused the contact to crash into a tree and the air bags failed to deploy. The police report was file. The contact sustained major injuries. The vehicle was destroyed and was towed away from the crashed scene. The dealer was not contacted. The manufacturer was made aware of the failure who did not offer any additional assistance. The vin was not available. The failure and current mileage was 740.
Air bag light came on and stays on. Randy wise dealership in durand michigan checked and charged us. They said they don't know what is wrong with it.this knocked out cruise and traction control.this came on while in motion and is now on continuously.the other safeties are out too.
There is no major problem but my air bag light went off and i took it to my dealer and they told me that i would have to pay to replace occupant restart controller. I looked on recall site and it states that the problem would be fixed free of charge and they are trying to charge me $289+tax to fix it. Why???/ is there something that i am missing?
The contact owns a 2012 chrysler 200. The contact stated that the recall for nhtsa campaign number: 16v668000 (seat belts, air bags) was excessive. The contact received the recall notification over twelve months ago. The dealer stated that the parts were not available for repair. The manufacturer was not notified. The contact mentioned that the air bag warning indicator illuminated intermittently. The failure mileage was 40,000. Vin tool confirms parts not available.
Takata recall. The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number:16v668000 (air bags, seat belts) and stated that the part was not available within a reasonable time frame to schedule the recall repair. The dealer did not give a specific date for when the part would become available. The manufacturer could not provide an estimated date for when the contact's vehicle would receive the recall repair. The contact was not experiencing a failure. Vin tool confirms parts not available.
Takata recall. The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (air bags). The part to do the repair was not available. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. Vin tool confirms parts not available.
The contact owns 2012 chrysler 200. The contact stated that a vehicle crashed into the passenger's side of the vehicle. The air bags did no deploy. A police report was not filed and there were no injuries. The cause of failure was unknown. The manufacturer was not notified of the failure. The failure mileage was unknown.
I received notice of recall s61 for replacement of occupant restraint controller in november 2016. I registered to be told when repairs could be madewith mopar.comas of this date i am told the parts for this repair are still not available i believe adequate amount of time has been given to the company to secure the parts. Can you facilitate this for me?
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (air bags); however, the part to do the repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The manufacturer was contacted and confirmed that the vehicle was included in nhtsa campaign number: 16v668000 (air bags), but there was no date for when the parts would be available. The vin was unknown. The dealer was not contacted. The contact had not experienced a failure.
Takata recall. The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (air bags) and stated that the part was not available within a reasonable time frame to schedule the recall repair. The dealer (eide chrysler, 1112 missouri ave, bismarck, nd 58504, (701) 223-1170) did not give a specific date for when the part would become available. The manufacturer could not provide an estimated date for when the contact's vehicle would receive the recall repair.the contact was not experiencing a failure. Vin tool confirms parts not available.
I was in an accident on i 79 in pa going 70mph slid on some slush spun around a few times before i hit a guardrail head on and the airbags never when off in my car.
My airbag light had come up. It turned of once then came back on. It has not turned off since then. It started on 6/19/17. It turned of once when i was at a stop light. Now it's always on.
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (air bags, seat belts); however, the parts to do the repair were unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The manufacturer was notified of the issue. The contact had not experienced a failure. Vin tool confirms parts not available.
The contact owns a 2012 chrysler 200. The contact stated that the air bag indicator illuminated. The local dealer was contacted. The vehicle was not diagnosed or repaired. The manufacturer was notified of the failure. The failure mileage was 90,987. ... .updated 11/16/17 the consumer stated the parts to repair the vehicle were ordered.
The contact owns a 2012 chrysler 200. Upon starting the vehicle, the air bag indicator illuminated. The contact previously received notification of nhtsa campaign number: 16v668000 (seat belts, air bags). The part to do the repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue and stated that parts for the recall repair were not available and that they did not know whether the air bag indicator illuminating was due to the recall or not. The contact spoke to central jeep chrysler dodge ram of norwood (56 boston-providence turnpike, norwood, ma 02062) who stated that parts for the recall repair were not available; however, they could diagnose the failure for a fee. The vehicle was not diagnosed or repaired. The approximate failure mileage was 115,000. Vin tool confirms parts not available.
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (seat belts, air bags); however, the parts to do the repair were unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The local dealer and manufacturer were not contacted. The contact stated that he was informed a year ago that he would be contacted when parts became available and that owners would receive a second notice in august 20017 when remedy parts became available. The contact had not experienced a failure. Vin tool confirms parts not available.
"takata recall" the issue is in the electrical warning system. The warning indicates air bag. Air bag light is on and has stayed on continues to stay on. It does not flash it just stays on. On the start of the vehicle once the ignition switch is turned on and the car is running. It continues to stay on while vehicle turned on and running. I believe it may be a recall with the modular.
Van horn chrysler and dodge in plymouth wi. Sold me a vehicle that was in a major front end accident. When they sold me the air the airbag was not attached. The steering was pulling to the right. The suspension was severely damage, it was so severe that when i took the car to chrysler, i spend money there to get the problems repaired. Because van horn wouldn't pay for the repairs. After chrysler couldn't make the repairs, because the car had been in a major accident from the previous owner. Chrysler referred me to the body shop, where i was out of pocket for another additional repair.i also forward this information to chrysler customer assistant1-888-992-1997. My case number there is [xxx].they (chrysler customer assistant) said the car should have never been sold. They informed [xxx] manger to get in touch with me to make a settle. Which he hasn't as to 10/14/205. Tom boweo was the person that i spoke with at milosch's palace collision center, lake orion mi. (248)276-6653. The car is registered to [xxx]. My email address is[xxx]. My phone number is [xxx]. My cell number is [xxx]information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6).
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number:16v668000 (seat belts, air bags) however, the part to do the repair was unavailable.the contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. A dealer was contacted and stated that the vehicle had no recalls and that the only problem the vehicle had involved a bolt. The contact had not experienced a failure. Vin tool confirms parts not available.
There was a recall on the airbag and seat belt pretensioner deployment capability on my car that started on october 1, 2016. When i got the recall notice in october it said that there was no current remedy. It's now december and there still is no remedy which means that the problem won't be fixed in the foreseeable future which is outrageous. If our lives are at risk because a car company can't get off its [xxx] and fix this, then the government needs to intervene. I don't feel safe driving my car because in the back of my mind i know that it might not protect me completely if i get in a crash which should not happen. This needs to be fixed now.information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6).
Airbag warning light on dash, chrysler stated it was only recalled for computer software update.dealership stated airbag has internal failure of orc and needs console replaced.chrysler stated that they would have repaired problem if my car was 2011 model.would not repair airbag issue since it is 2012 model.airbags may not deploy when needed, and may deploy when not needed.very dangerous issue, dealership wants over 450.00 to correct.
The contact owns a 2008 (na) chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (air bags); however, the part to do the repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. The vin was not available. Parts distribution disconnect.
The contact owns a 2012 chrysler 200. The contact stated that while driving approximately 45 mph, the vehicle was crashed into on the driver's side. The driver's side frontal air bag failed to deploy upon impact. The contact sustained injuries to the face and chest. The vehicle was towed to a private repair center. The manufacturer was not made aware of the failure. The vehicle was not repaired. The failure and current mileage was 4,000. ....updated 03/18/13updated 04/02/2013
I get a recall about air bag (something about the seats) and my airbag light comes on. I take it in and the dealer wanted to charge a diagnostic charge. I contacted chrysler and was told to take it back to the dealer and they would look at it. Took it back, and the dealer, herman jenkins in union city tn, stated they could not find the problem. Today i have a air bag light on all the time. Was told by a mechanic, that if the light was on the air bags will not deploy. My wife drive this car every day. I will not buy another chrysler, if they can't stand behind their product. Could not believe that the dealer could not fix a product they sell!.
Recall date was september of 2016 and almost a year later the parts still have not be released to dealers to fix this issue.this seems like an excessive amount of time to wait for such an important recall issue
My airbag light is coming on while i'm driving and i am still under warranty.
Vehicle randomly stalls, reverse and drive. It will stall in traffic, while driving and backing out of the driveway. I had a p0335 code after it stalled about 10 time.i have changed the crankcase sensor 3 times but does not correct the issue. Also have electrical issue with windows not working and only half the defrost working.
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (seat belts, air bags); however, the parts to repair the vehicle were unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. Sunset dodge-chrysler-jeep-ram (7745 south tamiami trail, sarasota, fl 34231-6841, 941-922-2400) was contacted several times and informed him that they only received two replacement parts per month. The manufacturer was made aware of the issue. The contact had not experienced a failure. Parts distribution disconnect.
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (air bags). The part to do the recall repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The manufacturer was not aware of the issue. The contact had not experienced a failure. Vin tool confirms parts not available.
The airbag light came on so i got the code reader and scanned it said it was (driver active headrest control circuit open
The contact owns a 2012 chrysler 200.the contact received the recall notification related to nhtsa campaign id number 13v282000 (air bags , electrical system). The contact stated that the dealer and the manufacturer were contacted numerous times and they had no idea when the parts would become available for the repairs.the repair was not taken care of in a reasonable amount of time. The contact had not experienced a failure.
The air bag & seat belt tensioner may not deploy, replacement of occupant restraint controller is required.it's been over 6 months with no remedy provided by chrysler, this is unsatisfactory.[xxx] gilbert, azinformation redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6).'
The contact owns a 2012 chrysler 200. The contact was driving approximately 25 mph when the brakes were depressed however, the vehicle did not stop and began to slide instead. The air bag warning light illuminated simultaneously with the failure. In addition, there was a loud whistling sound coming from the front end of the vehicle. The contact was able to stop the vehicle on the shoulder and the vehicle was later taken to the dealer for diagnostic testing. The contact stated that the vehicle was taken for diagnostic testing twice. The technician advised that the clock spring sensor failed and would need replacing. The vehicle was repaired. The approximate failure mileage was 11,500.
Randomly shuts down while driving down the road,with no warning
Started with the abs and traction control lights coming on, my cruise control stopped coming on and a week later i pulled out of the bank and stopped alone side of the curb and the car just shut off, no restarting at all nothing happens, the right info panel said no bus, its at the chrysler dealer ship now and they can find nothing wrong with it at all, even though it wont come on.
Vehicle randomly stalls, reverse and drive. It will stall in traffic, while driving and backing out of the driveway. I had a p0335 code after it stalled about 10 time.i have changed the crankcase sensor 3 times but does not correct the issue. Also have electrical issue with windows not working and only half the defrost working.
Vehicle shuts off while driving.this happened 3 times in less than 3 years.driving vehicle and instrument panel lights up and vehicle shuts down.1st time - july 2015,this happened coming into a roundabout - lost all power including steering and brakes.was lucky enough that no other vehicles were around.dealer replaced tipm.same thing happened less than 1 year later (april 2016).in a parking lot and vehicle just shut off.dealer replaced tipm again stating part failure - under warranty since was less than 1 year since replacement.now less than 2 years later on 12/26/17 vehicle shut off while driving 70mph on the highway!was lucky enough to be on 2 lane highway instead of 4 and able to get to the side of the road.took to dealer that purchased from (happened closer to that dealer than the one that previously had fixed).explained situation, that part was replaced before same thing happening.they said nothing wrong, couldnt find anything and sent me on my way - drove back roads because i was afraid to drive.not even 30 miles later and same thing happened.shut down while driving.able to restart vehicle every time.took to dealer that had fixed in the past.tipm failure again!this is 3 times that the part has failed.covered under warranty again - they said part warranty had been extended from 1 to 2 years.this is a known problem and definately a safety hazard!!i got the car fixed and traded it in the day i got it back!3rd failure was at 113k miles.car purchased brand new in 2012.
We got recall p25/nhtsa 14v-234i called the dealership in garden city long island ,ny tel 516 292 9764 to make an appointment, i have been there several times for oil change. I requested about this recall and there response-1- oh we do not have part in stock, we will call you when we get the part,2- on the phone they keep transferring the line, finally i end up with leaving message, but no call from them.3-they keep you on hold so long that you have to hang up the phone.i do not know what to do. I feel this dealership is arrogant, irresponsible, unprofessional and danger to the car owners.i hope you take action immediately. I might be one case but there are millions of mini van like mine.thanks for your cooperation.[xxx]information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6).
The contact owns a 2012 chrysler 200. The contact stated that the heater core malfunctioned. The vehicle was taken to the kernersville chrysler dodge jeep ram dealer (950 nc-66, kernersville, nc) where it was diagnosed that the heater core failed. The vehicle was repaired, but the failure recurred at approximately 72,000 miles. The manufacturer was notified of the failure. The vin was unknown. The approximate failure mileage was 19,000.
There was a recall on my vehicle i took it to the dealership in harrisonburg va to be repaired. They only fixed the active head restraints. My car failed a state inspection due to my airbag light illuminating. I have read that "certain" chrysler 200's 2012 they are to reprogram the tipm then replace the occupant restraint module if needed. They refused to replace this gave me an estimate of $400. I called chrysler and they also said my car was not recalled based on the vin and my issue. I am a single mother with two kids my car has 67,000 miles on it has never been wrecked or damaged and i believe chrysler should replace this. My car is only 4 years old an airbag should not become defective in 4 years. This exact issue is what other 2012 chrysler 200s have also. I am still unable to have my car pass a state inspection and i also informed chrysler that when passengers ride in that seat they are putting lives at risk by not acting quickly. It is dangerous and chrysler should recall all 2012 200's. It hey informed me the problem is in the dash i don't even feel safe driving my car what if my air bags don't deploy? i will live with that the rest of my life and chrysler should be held accountable for negligence. Just because my vin number doesn't match at this time or the time frame they claim the defects were installed doesn't mean the part they installed isn't defective. I hope you all take this matter very seriously. This is a safety issue that could take or save lives.
My car received a software update for the pcm on 3/2/2017. On 03/6/2017 my car shut off completely in the middle of driving down the interstate.
The contact owns a 2012 chrysler 200. The contact stated that when taking off from being idle, the accelerator pedal was depressed but the vehicle failed to respond. The failure recurred on numerous occasions. The vehicle was not diagnosed or repaired. The manufacturer was not made aware of the failure. The approximate failure mileage was 60,000.updated 4/29/15the consumer also stated the vehicle stalled at stop signs. Updated 05/05/15
I bought my car brand new in 2012 from chryaler dodge and jeep in springfield pa. I babe around 96,000 miles on my car and this will now be the third alternator that has been put in my vehicle. From what i know, the alternator should last up between 80,000 to 100,000 miles. I believe there has to have been a defect with my specific car. Along with some of the other recall items i am now reading about with my model, having kids, i am increasingly concerned about my health andsaftey driving this vehicle. I want to know what can be done about this on your end
Takata recall ----while driving, in motion, to pick up my daughter from schooli start to hear a winding sound. My electrical system that powers the radio and uconnect system starts to shut down.my abs light andesc light comes on and im startingto smell a burning in the car,while this winding sound is getting louder, smoke is coming from the hood.the timing or transmission is disabled , the car shutsdownin the middle of the road, in front of the school exit. We could have been struck from behind or the side of the vehicle. Car smellslike it caught fire.
I am an owner of a 2012 chrysler 200 and on feb. 1st while sitting in my driveway a fire started in the internal. I called chrysler and i received a letter that they will not take responsibility for any manufacturing or assembly error. A week prior before the car caught on fire the heat would only work on the driver side. This vehicle is not safe and it is very disturbing that a company like chrysler would not take responsibility for an unsafe vehicle.
Takata recall the tipm has malfunctioned car will not function of start
I think my car has electrical issues window start and stop working . I replaced a headlight and it starts and stops working at one point my started stopped and started working. My headrest deployed on passenger side while driving and it's a big space now on it
The convertible top motor is broken and the top will not go up or down. Luckily it is broken in the up position. I have been trying to get the part replaced through chrysler and all they can tell me is that the part has been discontinued and no after market parts are even available. I bought this car in october 2016, because l wanted a convertible and now i have been without a working top since june 4,2017. I was parked in my driveway when l tried to put the top down and it would not work. I have been told by the chrysler dealership that the part number needed to fix this problem is#68028392aa.
The contact owns a 2012 chrysler 200. The contact stated that while driving at 70 mph, the headlights failed without warning. The contact also stated that the traction control, the cruise control and the abs warning lights were illuminated. The contact also stated that there was a grinding noise coming from the front of the vehicle. The vehicle was not taken to be diagnosed or repaired. The manufacturer was notified of the failure. The approximate failure mileage was 112,000.
While driving 15mph in a 25mph zone due to not being able to see the road on a downgrade i almost hit an animal and coming close to also hitting a low center median being unable to see in front of my vehicle more than 10 feet or less. Informed chrysler and as other people stated they want to do an adjustment and diagnosis of problem. I have and drive other vehicles and have not had this issue with anything else just this vehicle there is not enough light and the cutoff is seriously bad.
I am writing this complaint in response to my 2012 200 chrysler which has completely lost all power.it started out with the windshield wipers stopping on me and then one day while driving the car i lost power.the steering wheel locked up and the car came to a complete stop.luckily i wasn't on the highway and was pulling into the parking lot of my office building.after speaking with chrysler i was told there was nothing they could do since this part is no longer covered under warranty. It seems strange to me that this part on my car had a recall for the software a few years ago and now the hardware is bad.i see a ton of complaints on this very issue including a lawsuit.if safety is of concern, it would seem like they would anything in their power to help the consumer.
My stepdaughter's car (2012 chrysler 200), apparently has a bad tipm. Took it to checker who diagnosed the "check engine" light which had come on and told us it was most likely the tipm. We then took it to the local chrysler dealer (earnhardt, chrysler, jeep, dodge, ram in gilbert, az) for an n38 recall issue (active head restraint/air bag) they told us they would reset the tipm module and we were hoping to have the issue resolved. It should be noted that before we took it for the recall issue, the car had seemed to be working fine and mysteriously the check engine light had turned off. Well, lo and behold after they reprogrammed the tipm and did the air bag recall we picked up the car and my wife immediately noticed that the check engine light had reappeared and the car was once again driving like [xxx]! i came home and started doing research and found this webpage that told me to file complaints, however, i also noticed that there was apparently a software patch that chrysler came out with as a result of this problem. I called chrysler @ 800-992-1997 thinking i might get someone who could give me more information but of course this hapless character didn't know what the hell i was talking about in reference to a "software patch" he did call the dealership we were just at for the recall, but of course, got nothing but an answering machine. He told me he left a message and they would call back monday to talk about our concerns. I'm not holding my breath waiting for the call.what bothers me most, and is extremely frustrating is the fact that thousands of people have contacted chrysler and other sources and have gotten nowhere.information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6).
My abs light has turned on.and my abs isn't working.also my radio also is only working intermittently.
The contact owns a 2012 chrysler 200. When the contact shifted the gear into the park position, the instrument panel gauges fluctuated independently and the vehicle stalled without warning. The vehicle was able to restart on the first attempt; however, the failure recurred. The vehicle was towed to an independent tow company (718-828-1500) who informed the contact that the alternator failed and needed to be replaced. The vehicle was not repaired due to the quote provided. The manufacturer and dealer were not contacted. The failure mileage was approximately 101,580.
Alternator dies at 78,000 miles. Heat no longer works due to heating core at 60,000 miles.
Car stalled out while driving. This happened several times. Sometimes while driving on a straight road and sometimes when making a sharp turn to park. Car horn also started going off on it's own while driving. Had to have the tipm module replaced. This is a safety issue.
Wipers only work on high. Wiper motor shorted to ground causing internal collateral damage to tipm. Removed and replaced wiper motor. Removed and replaced tipm and updated software.
Air bag light is on , going threw brakes and tires every 6 months sense i bought it in 2016. Also no heat started at passanger side and worked its way towards drivers side. Also front windows do not go down started passanger side and 3 months later no driver side. Also was driving about 35 mph made right hand turn car has stalled 5 times.
The contact owns a 2012 chrysler 200. The contact stated that while driving 20 mph, the heating system was activated and cold air emitted only from the passenger side vents. The failure recurred continuously. The vehicle was not diagnosed or repaired. The manufacturer was notified of the failure. The failure mileage was 55,000.
The electrical throttle light keeps coming on and the car shuts off.
The car shut off without warning leaving me stranded 10 miles from home. I now believe it happened ones before, the car was towed and on a whim the driver turned the key and the car started.
The contact owns a 2012 chrysler 200. The contact stated that there was no failure with the horn operating until the vehicle was serviced for an unspecified manufacturer recall regarding the air bags. Months after the air bag recall was serviced by massey yardley jeep chrysler dodge ram (777 north state road 7, plantation, fl 33317, 954-327-4000), the horn failed to function properly and various warning indicators flashed on the instrument panel without warning. The contact was waiting for a response from the dealer to determine if they could duplicate the failure. The manufacturer was notified. The vehicle was not repaired. The approximate failure mileage was 46,000.
I was traveling 55 mph on the highway my tire blew out an the fender blew off but somehow the cars whole engine wiring system was ripped out of the car in which the whole car went completely dead of all electricity thankfully i was able to pull on shoulder of highway before the car stopped rolling.
The contact owns a 2012 chrysler 200. While driving 55 mph, the vehicle jerked and stalled without warning. The vehicle was able to coast to the side of the road where it failed to restart. The vehicle was towed to darcars chrysler dodge jeep ram of silver spring (12511 prosperity dr, silver spring, md 20904, (301) 622-0010) where it was diagnosed that the integrated power module needed to be replaced. The vehicle was repaired, but the failure recurred eight times. The vehicle was taken to an independent mechanic where a diagnostic test was completed, but a failure code could not be found. The manufacturer was notified of the failure and informed the contact to take the vehicle back to the dealer. The approximate failure mileage was 80,000.
Takata recall - i never received any information regarding this recall.i am just now (july 2016) experiencing the airbag warning light coming on and a warning tone being emitted randomly while i'm in motion.i'm interested to know if i can still take my car to the dealership to have it worked on under n38 13v282?
Purchased a used chrysler 200 in february 2017 at 87,xxx mi. It is now june 2017 and 3 times in the last 3 days my car has suddenly died. The first time i was slowing down and made a right turn and upon accelerating it died, dash lights illuminated, quickly tried to restart and was unsuccessful with just nothing happening when turning key. Took key out of ignition and retried and started right up.next day i was again slowing down and making a right turn and bam same thing same details. 3rd incident i was driving straight and the car stalled this time i was doing about 15 mph and the steering locked up, quickly took key out and restarted. Engine light was on and diagnosed as crankshaft position sensor malfunction. Replaced the sensor and have only driven for short distance as the first 2 times this happened were terrifying enough. After hours of online research i've found this is common and just being neglected. Chrysler fix this issue before someone gets seriously injured
The contact owns a 2012 chrysler 200. The contact stated that there was a premature failure with the vent control electronic function. The vent controls failed to generate warm air when the heating function was used. An independent mechanic stated that the heater core needed to be replaced. The vehicle was not inspected by a dealer. The manufacturer was notified of the failure. The vin and failure mileage were not available.
The contact owns a 2012 chrysler 200. When the contact attempted to drive the vehicle, the heater on the front passenger side failed to function and prevented the passenger side window from defrosting. The vehicle was taken to doug marine motors (1120 clinton ave, washington ct house in oh 43160) where it was diagnosed that the heater core needed to be replaced. The vehicle was not repaired due to the repair fees. The manufacturer was contacted and did not assist. The vin was unknown. The approximate failure mileage was 60,000.
I just rented the vehicle and noticed the following,the battery has no boot or other insulation device protecting either its positive or negative terminals. The battery is located down in a well in front of the front left tire.it would be very possible for someone to accidentally drop a metal tool down into that well where it could cause a short-circuit to the negative terminal. A short-circuited auto battery is capable of delivering hundreds of amps of current, which equates to an electric arc welder.the potential dangers of those unprotected battery terminals should warranta safety investigation to determine if a recall should be initiated to correct this apparent desgin flaw.
The contact owns a 2012 chrysler 200. While driving approximately 60 mph, the vehicle lost power, but did not stall. Additionally, the tail lights and driver's side headlight were inoperable. The vehicle was taken to deacon's chrysler dodge jeep ram (located at 835 som center rd, mayfield, oh 44143, (440)442-0424) where it was diagnosed that the totally integrated power module needed to be replaced. The vehicle was not repaired. The manufacturer was notified. The approximate failure mileage was 75,899.
To start off the abs and traction control will not stop turning off and on even after replacing everything . Almost all the time when it rains they will kick in the e brake and start grinding . No matter how many times i change the brakes and rotors and master control they never stop squeaking . Lastly almost all the electrical problems started after the alternator failed and i had to replace it . My speedometer just died on me today and i have no clue how that happened .
The contact owns a 2012 chrysler 200. While driving 10 mph, the tire pressure gauge malfunctioned, the seat belt warning indicator illuminated, and the air bag warning indicator illuminated. The warning indicators functioned normally after 20 minutes, but the air bag light remained illuminated and a tipm warning indicator flashed. The vehicle was not diagnosed or repaired. The vin was excluded from nhtsa campaign number: 13v282000 (air bags, electrical system). The failure mileage was approximately 70,000.
The contact owns a 2012 chrysler 200. The contact stated that while driving at various speeds, the vehicle stalled without warning. The contact stated that on several occasions, the vehicle failed to restart. The vehicle was taken to an independent mechanic who replaced the alternator however, the failure recurred. The cause of the failure was not determined. The local dealer and manufacturer were not notified of the failure. The failure mileage was unknown.
The car has stalled on four different occasions while driving.it stalled three time while driving in traffic. One time it stalled on the highway. The car has turned back on after a couple of tries. A malfunction indicator light comes on after the incident and stays on for a period of time. The light simple goes out without any intervention. Everything appears to be running okay and then another incident of stalling occurs.
The contact owns a 2012 chrysler 200. The contact stated that the vent control failed to release heat from the vent on the front passenger side. The failure prevented the windows from defrosting in inclement weather. The vehicle was taken to yark chrysler jeep dodge ram (6019 central ave, toledo, oh 43615, (419) 877-7712) to be diagnosed. The manufacturer was notified of the failure. The vin and failure mileage were not available.
The dashboard lights and the head and back lights will flicker on and off.the car has shut off while driviing in traffic.sometimes it doesnt start at all , i have to baqng the door and then the loghtas will come on.i put a brand new battery and altintor in the car and my nechnanic doesnt have a clue what is wrong woth it.believe it to be the computer system.
When going over the bridge or entering into traffic car seem to stall, radio and light shutoff and give me a error message enter id code. Have been nearly rear ended by on coming traffic.the console for the heat controls have fell down and dealersays they cannot find anything wrong with it.purchased the car in march of 2012 and have had problems since i bought it. I love car but hate all the problems that i am having and it's only been 9 months and took it back to dealer about 4 times already and have an appointment on 1/11/2013.
This is a problem that started with the prior owner of the vehicle but the connecting rods in the engine are failing the hazard switch does not work and the traction control does not work i noticed atleast the connecting rod was a safety recall and vin specific it was noticed when the cam shaft started making noise due to debris
The contact owns a 2012 chrysler 200. The contact stated that the vehicle failed to start. The vehicle was diagnosed by an independent mechanic who determined that the tipm module had failed. The dealer was made aware of the failure and the contact was advised to tow the vehicle to their location for a diagnostic test. The manufacturer was made aware of the failure and advised the contact to take the vehicle to the dealer for the diagnostic test. The vehicle was not yet diagnosed nor repaired. The approximate failure mileage was 87,000.
Thereis an awful smell of fumes coming through the airvents inside car. It's so terrible that it takes your breath away. Well i found out there is a recall on this because it has something to do with thac 7 heating system. Mold and bacteria has set up around the heater core and the antifreeze has started looking like thick glue or something. Now my heat does not work correctly. The smell that's coming through the vents, well i had to go to emergency room because i could not breath. The smell settles in my clothes and by me breathing it in, the smell has settled in my nostrils. By the time i get to work all my clothes i have on smells. Went to hospital because it has made me so sick, my yes burn from the smell.this is dangerous. The mechanic i saw said the compartment where the antifreeze is needs to be flushed out and thermostat replaced and probably valve gaskets and the heater core may be stop up also since the antifreeze was like glue,the fumes from the vents is bad it can affect your respitory system and your breathing. Lake keowee chrysler dodge of senca sc was called about this problem. They said they needed the number from recall. Well this license mechanic is going to tell me how to handle this problem. This has affected my health and it also affected my heating system. It will not work. I have to put on face mask so i won't have to smell that awful fume. I already spoken to an attorney about this.
The contact owns a 2012 chrysler 200. While driving approximately 10 mph, the engine stalled without warning. The contact required a jump to restart the vehicle. The engine started and the instrument panel illuminated, but the failure recurred. The vehicle was not diagnosed or repaired. The manufacturer was made aware of the failure and advised the contact to take the vehicle to a dealer. The approximate failure mileage was 56,000.
On april 26, 2012, i purchased a brand new 2012 chrysler from an official chrysler corporation dealership.since then this car has been put in the shop approximately 30 times for from medium to major problems. The 1st major problem was 9/26/212 which was diagnosed as gear-rack and pinon.it has had two lifters(relative to the motor) because of loud tapping.three heater cords; a couple of re-calls;transmissions leaks; internal engine damages; headlamps needed immediate replacements; washer fluid tank leaked and needed immediate replacement; the car horn failed to blow on demand; brakes needed immediate replacements; camshaft, rockers had to be replaced twice; heater cord experienced internal failure and had tobe replaced; brake pads; brake light (dashboard) has been beeping on since 2013 and is still doing the same thing today; engine air filter had to be replaced; and a host of other vehicle problems that should not be happening on a brand spanking new 2012 vehicle!!please assist and advise.
The car consistently stalls out at least 4-6 times a trip in the middle of driving, if not more. It also honks on its own during that time.it was brought to the dealership and a shop and they couldn't find anything wrong
Driving home from work i entered on to the highway and while driving, the vehicle completely shut off. This has happened three different times and i have two children and this is the only vehicle i have. I am fearful that this problem may cause injury.
There is no heat on passenger side so the defrost does not work and it affects visibility when driving.
Engine shuts off while driving down the road. It happens on the freeway, on city streets, or at idle. We had the pcm updated in december 2016. It is now march 2017 and the vehicle continues to shut down while driving or at idle. It is extremely dangerous. The brakes barely work and you lose power steering when this happens. This is a serious issue and needs to be addressed. There are hundreds if not thousands of posts online about this issue, with no resolution. This needs to be addressed before someone dies.
The contact owns a 2012 chrysler 200. While driving approximately 10 mph and activating the right turn signal, the windshield wipers engaged automatically. The failure recurred every time the turn signals were used. In addition, the heater would blow hot air through the driver side vents and cold air through the passenger side vents. The vehicle was taken to a dealer, but was not repaired. The manufacturer was not notified of the failures. The vin was unknown. The approximate failure mileage was 76,000.
First time car wouldn't start.dealership charged battery and did software update.second time car wouldn't start they replaced battery.third time car wouldn't start battery completely drained they said it was a glove box switch.fourth time car wouldn't start they said it was the usb cable keeping the radio powered on all the time.same chrysler dealership worked on it all four times.brand new car bought august of 2012.all four times have been in less than two months!this car is not safe.chrysler is not doing the right thing by their customers!any help would be appreciated.in the usa we should not have to put up with being ripped off like this.
With no warning, no engine light, on i pulled out into traffic, turning right on a two way road the car went into traffic and suddenly no power. I was lucky to be able to drift on the shoulder.i towed my car to the dealer and was told it was the crank sensor. I asked what caused it, because i had no warning, they said it was probably a short. This could have been very tragic.
The contact owns a 2012 chrysler 200. While the contact's husband was driving various speeds, the battery died and the mirrors, lights, and horn failed. The vehicle was taken to hilton head chrysler jeep dodge ram fiat (265 drivers way, hardeeville, sc 29927) where it was diagnosed that the alternator, generator, and battery failed and needed to be replaced. The vehicle was repaired. The manufacturer was made aware of the failure and stated that the vin was not included in nhtsa campaign number: 14v634000 (electrical system); however, the failure later recurred and the vehicle was taken back to the same dealer where it was diagnosed that the failure recurred; however, the vehicle was now included in nhtsa campaign number: 17v435000 (electrical system). Both the dealer and manufacturer stated that the repair parts were not yet available. The vehicle was not repaired. The approximate failure mileage was 59,914.
I bought this car use with 27,000 mile on it. I have only had the car for 45 days or so. My car is jumping forward when i come to a stop. At first the lurching was very faint now at 31,000 miles the lurching is more pronounced.i took the car to the dealership prior to the warranty ending and they acted like they where unaware of the issue/or didn't understand the issue.any way i am beginning to feel unsafe since it is happening more.the car lurched forward during a sudden stop one time, not good.
The battery light in my car continues to come on even after having the battery replaced as well as the alternator replaced. Also the internal lights inside of my carbegan to blink like crazy, air conditioner was coming on/off, and the lights even shut off at one point almost as if the car couldn't control itself. I do not feel safe driving it.
While driving my vehicle back the office from my lunch break, i made a right hand turn onto the main road and began to accelerate the vehicle with more gas.at about 35mph the car engine completely shut off and i had to coast to the side of the road with no power steering.i had to wait approximately 20 mins until my car would restart again.i was able to get back on the road until after another few hundred yards of driving the car stalled again completely.i was then forced to call a tow truck to have it taken to an auto shop.
My passenger side window does not come back up after being let down, using the driver window button or the passenger button. I have replaced the motor, the switch and regulator but same issue. I have research and looked online where this seems to be a common problem even after the individuals replaced all parts from 2004- up until now.
I was driving down a busy street, trying to make a left hand turn through traffic, and my car stalled without no warning and everything was locked including brakes. I took it into chrysler and they couldn't find anything wrong with it because no fault light was coming on. So they took the next step of putting a module on my car for 2 days to see if it happens again, but lucky for me it didn't because the first time was scary enough for me. Then when i took it back in they just told me that when my car does that just put it in neutral and restart it. So three weeks later my car did it again but this time i was on a busy freeway going 70 mph, so i tried their suggestion and it did not work, for the second time everything just quit working in my car. So i called them again talked to the manager at chrysler and he said if there is no lights coming on when my car does this he really can't do anything about it.
"takata recall" my air bag light is on in the dash board my car was already at the dealership for another issue the agent informed me the airbag modular has failed i informed the agent there is a recall for the tipm.a defective tipm can causeair bags not to inflate and other major issues.the dealership want to charge me 429.00 to fix.
Vehicle stalled and would not start while driving (2 times )towed to dealer as (both times) tow driver could not restart.dealer reported no computer codes and car started after car started on problem.there appears to be common safety hazard that has been experienced by many owners, that reportly chrysler and nhtsa agreed upon a resolution to avoid a recall by chrysler of this safety hazard in sept 2012.chrysler doesn't acknowledge and not sharing this information with dealers so they can take corrective action. Various attempts tried to resolve this hazardouscondition have included replacing the powertrain module, camscope replacement, monitoring the on board with a copilot computer-which also showed no codes.the dealer did say that chrysler suggested an additional module be added to the on board computer, but none of their customers returned a third or more times as previous attempts were unsuccessful and appeared to give up.this life threatening safety hazard needs to beinvestigated and resolved, as we were driving on aroadway and the motor just shut off.,if this not resolved it will sometime cause injuries or deaths, which could end up with a recall something that chrysler possible replacement of on computers.
Still not fixed. Cleaned throttle body, and when that didn't resolve the issue they replaced throttle body. Car still stalls at random times, both while moving and waiting at lights. Almost been in several accidents. All loss of power steering and control of the car.
I noticed after i purchased my vehicle in 2012, i started having issues with my car in 2013.my car started having heat coming from the bottom of my driver and passenger side.i ignored this issue but then it started happening more often.on my last oil change the dealer didn't fill my overflow for the antifreeze so i had a friend to fill it up.after filling the antifreeze he decided to turn on the engine.what happens next is that the antifreeze began to boil.this should not be happening.i made an appointment at the dealer and took it on yesterday.i was told it was the tipm which was shorted out and that the fan wasn't coming on like it should.the cost of this repair is $1275.00.i believe chrysler is aware of the issues and that they need to reimburse customers for this issue.
Engine shuts off on highway going full speed limit surrounded by heavy traffic. I was terrified. The engine light comes on & can't get car started. Then car starts & engine light goes away. Not to mention transmission is leaking & new transmission was put in 2015. Chrysler can't get me in until 4/19/18 bc its busy season. This may be why windshield wipers come on everytime i turn left.
The contact owns a 2012 chrysler 200. The contact stated that the battery warning indicator illuminated. The vehicle was serviced per an unknown recall at du page chrysler dodge jeep ram (433 e n ave, glendale heights, il 60139, (630) 446-1400); however, the remedy failed to repair the vehicle. The contact mentioned that all the warning indicators illuminated on the instrument panel after the recall repair. The manufacturer was not made aware of the failure. The failure mileage was 75,000.
Windshield wipers quit working. Only wipe on high. Took into dealer to repair, they replaced the wiper motor. Did not fix problem, they then ran codes to tell me it is the tipm. My extended warranty company said they will not cover, problem still not fixed.
I was driving on the expressway and my car died without any warning. I brought it to the dealership and they said i had oil in the injectors. They cleaned it up and sent me on my way for $715. Not even a month later i'm still having the same issues and nowsometimes it's not starting. So another repair shop changed the battery and starter, after the work they run some tests and say that i have a bad tipm to bring it back to the dealership. I bring it back to them and they want around $1800 now for this repair. I called chrysler and spoke with them about this and they refused to help in any way with this situation even though we are loyal dodge family customers(on our 5th vehicle). The reviews online show many people having this issue and it is a very dangerous and scary experience having your car die in the middle of the expressway with no power steering. I definitely think there should be a recall for this part to save the lives of others on the roadways. Thanks in advance
The contact owns a 2012 chrysler 200. While driving approximately 40 mph, the vehicle experienced a complete loss of power. In addition, the vehicle was no longer operable. The vehicle was towed back to the contact's residence. The failure occurred without warning. The vehicle was not diagnosed nor repaired. The manufacturer was notified of the failure. The failure mileage was approximately 42,000.updated 06/14/16*ljupdated 06/16/16.
My car heating system only heat half of the car and you can smell antifreeze coming through the vents. The passenger from window has stop working, it will come down but want go up. And the two windows in the back is trying to stop working. I just got this car on 11/01/2015 with only 32,000 miles on it.
My cars a/c heater blend door actuator has gone out. Upon my research i see there are numerous chrysler 200 owners with the same problem. It is my understanding gm recalled the same part from the same manufacturer. Shouldn't chrysler recall the part as well? the problem is persistent in the part continually clicks, cold air running through the vents when the heater is on.
Our car started over heating & smoke started coming out, the car was beeping & the gauge for the heat was sky rocketing to the h. White smoke started coming out of the left side of the engine & then the car was making a knocking sound. At the stoplight waiting to turn our car ended up shutting off & not starting.
The contact owns a 2012 chrysler 200. The contact stated that within two weeks of owning the vehicle, the head rest restraint deployed without warning. The vehicle was included in nhtsa campaign numbers: 13v282000 (electrical system, air bags), 16v668000 (seat belts, air bags), and 17v640000 (seats, air bags). The dealer (autonation usa corpus christi, 3115 s padre island dr, corpus christi, tx 78415-1815, 361-217-6733) was notified of the failure. The vehicle was not repaired. The manufacturer was notified of the failure. The approximate failure mileage was 52,000.
While driving the car.. Thecars electrical system stopped working. While driving on the freeway the car shut down and was almost in severe car accident because of the issue.there is a new battery and the alternator has been checked and is in great working condition.
While driving the battery light came on and electrical systems began to fail.radio, abs system, windows and ac all shut off.the car failed to accelerate properly and engine would not shift gears.braking and steering systems became compromised before car completely stalled and coasted to stop on side of road.approximately 2-3 minutes from battery light going on to the car becoming totally nonresponsive.car would not start, unless jumped.required tow.dealership states the issue was an alternator that shorted, and in turn burned out the battery.required the replacement of both the alternator and the battery at a cost of approximately $1100.00 (before negotiated discount of 10%).
Purchased new from chrysler dealer lot in april 2012. On occasion most commonly in summer months,when the vehicle is turned off the ignition will not release the key it is impossible to get the key out of the ignition i have to start the car and turn it off several times before it will release the key.
The contact owns a 2012 chrysler 200. The contact stated that the vehicle would not generate heat. The failure occurred without warning. The vehicle was taken to the dealer where it was diagnosed that the heater core malfunctioned and needed to be replaced. The vehicle was repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 54,000....updated 05/19/17
The heater on the passenger side of the car is not heating up and blows very cold air making it hard to defrost the window to see when driving
The contact owns a 2012 chrysler 200. The contact stated that the air bag warning light remained illuminated and the horn randomly sounded without warning. In addition,the vehicle randomly stalled numerous times. A pass time failure occurred and the dealer rewired the vehicle. A mechanic indicated that the tipm was faulty and may need to be replaced. The mechanic suggested that the vehicle be taken to the dealer for further inspection. The dealer was notified of the failure and the contact was uncertain as to why they indicated that the orc module needed to be replaced, but did not verify if the vehicle was included in nhtsa campaign number: 13v282000 (air bags and electrical system). The vehicle was not repaired. The contact was to check with the manufacturer to determine a repair solution for the vehicle. The approximate failure mileage was 89,444.
The contact owns a 2012 chrysler 200. While driving 50 mph, the vehicle accelerated independently, the rpm gauge increased from 0-4, and the speedometer gauge failed to display the actual speed. The failure recurred numerous times. In addition, the contact stated that the vehicle failed to start. The vehicle was taken to a dealer where the battery was replaced. The manufacturer was not notified of the failure. The approximate failure mileage was 99,000.
My 2012 chrysler 200 hard top convertible top will not go up or down. It was in a stationary position when i tried to put the top down and it would not go down.it has been broken since june 4,2017. The part number to replace it is 68028392aa. This part has been discontinued and therefore i am unable to put my top up and down. I have tried to work with the local dealer and have even contacted fca (chrysler administration). To date i have not been able to get any results. Can you please help? thank you.
The contact owns a 2012 chrysler 200 convertible. While driving various speeds, the vehicle suddenly shut off. The vehicle was taken to an unknown dealer who was unable to determine the cause of the failure. The manufacturer was notified of the failure. The failure mileage was 58,000.
My light are not working went to the dealer said i need part call (tipm) totally intergrated power module and the cost it 1,204.00.
The contact owns a 2012 chrysler 200. While driving 60 mph, the contact realized that the passenger side of the vehicle became cold. While the defroster was activated, the contact realized that only the driver's side was defrosting and not the passenger side. While the vehicle was stationary, the passenger side began to defrost. While the vehicle was in motion, the passenger side became cold. The dealer (east gate chrysler, 500 n shadeland ave, indianapolis, in) diagnosed that the heater core failed. The vehicle was not repaired. There were no recalls associated with the vin. The manufacturer was not notified. The failure mileage was 100,000.
Totally integrated control module has failed leaving my car unable to start and once started have lurches in acceleration. Will crank but not start.
The contact owns a 2012 chrysler 200. The contact stated that the vehicle was not emitting heat and the defroster failed to defrost the windows. The vehicle was taken to an independent mechanic where it was diagnosed that the heater core and the radiator needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure. The approximate failure mileage was 60,000.
There is an electrical problem on my car. First the lights would turn on and off, then the alarm would go off, then the radio stopped turing on, the ac stopped working and now it won't turn on.
While on the freeway in the rain, the windshield wipers stop in motion and stay in upward position against the windshield. Freeze up of wipers is intermittent. Wipers do not always respond to off position.
Projector type head lamps are aimed too low and cannot be adjusted as designed.on dark roads peripheral lighting from head lamps is non existent. Brights are needed but not practical for constant use and is illegal in town as well.this is a real design flaw and some one is goingto get hurt in a night time accident due to the poor design of the lighting system on this model.
Entering freeway was accelerating,merged into a lane and took foot off of the accelerator and the car rpms kept climbing and speed kept increasing within 10 seconds it stops and will respond normally usually happens when there is a quick attempt to accelerate.
Passenger side heater stopped working. Vehicle turns off while in drive and moving.
Driving car and preparing to stop for a red light the car suddenly stalled..no warning. Everything just quit. Thankfully i was already coming to s stop and was at a point where pulling off of the road was an option. Now today the car will not start. Only 58,000 and driven only locally.. Results pending on issue. No codes found yet. Mechanic states that at first look the car appeared to be out of gas, which is not the case. However it looks like this might be a fuel issue. I have seen recalls around the tipm and fuel sensors and prior years recalls for the car stalling.
While driving, the car began to rapidly lose functionality while warning lights were appearing on the dashboard until it abruptly shut down while driving in traffic. The time from no warning lights to complete loss of functionality was approximately 10-15 seconds. The shut down included an abrupt loss of power steering and braking capabilities while driving on a busy street at night. I was able to quickly compensate for the loss of power steering and braking and stop the vehicle while avoiding a crash, but just barely. Thankfully, i broke down next to two police officers who helped push my vehicle onto the side of the road. These officers may be able to attest to the fact that no noises or abnormal operation of the vehicle was apparent before the abrupt shut-off while driving. Attempts to restart the vehicle involved no clicking or the engine attempting to turn over. The vehicle is currently being repaired, but the preliminary diagnosis is one of a faulty alternator. I will attempt to retain the faulty alternator from the repair center. I had only started the car 2-3 minutes before the incident and there were no apparent electrical issues (engine struggling to start, lights dimming, etc.) while starting the car or during operation.
"takada recall" while driving down the road at 40 mph. I heard a chime and looked down at my instrument panel. The abs and the electronic stability control was on. Light was on for both. But instead of the esc it was the little car with wavy,jiggly lines under it. These two lights have been on constant for a good 3 weeks. It has gone out while driving a few times for a few minutes just to come back on and stay on almost all the time. There is no flashing of the lights. I don't drive every day. I drive around 5 times a week and short distances of 2 to 4 miles for the most part. There is also a whistling nice coming from the front of the vehicle. I don't think it is very safe to drive since the brakes and traction of the car are all to important part of me and my families safety. Please help with this issue. I paid and am still paying a lot for this car that now has 62000. Miles on it.
The contact owns a 2012 chrysler 200. While the vehicle was parked, the front passenger side headrest air bag inadvertently deployed. The vehicle was taken to a dealer where it was not diagnosed. The contact was informed that the recall stated only to replace the module, not the headrest part. The contact received notification of nhtsa campaign number: 13v282000 (electrical system, air bags). The manufacturer was not notified of the failure. The failure mileage was approximately 75,000.
Takata recall: there is a problem with the electronic throttle control light that causes the car to decelerate randomly, in combination with a ticking sound that comes from the air bag area of the glove box that is exacerbated by the ac and the heat being turned on.i feel that the car is unsafe to drive, although it says there is no open recall on these components.this happened several times to me on the expressway today.
Passenger side pushes out cold air, terrible to drive in and uncomfortable. Battery has been replaced 4 times in the last 2 years. Alternator as well. While driving to work, my windshield frosted over from being so cold and i had to veer off the road to avoid getting into an accident.
The contact owns a 2012 chrysler 200.the contact received the recall notification related to nhtsa campaign id number 13v282000 (air bags , electrical system). The contact stated that the dealer and the manufacturer were contacted numerous times and they had no idea when the parts would become available for the repairs.the repair was not taken care of in a reasonable amount of time. The contact had not experienced a failure.
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 13v282000 (electrical system); however, the part to do the repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. On a separate occasion, when the brakes were applied and the gear was placed into park, the vehicle accelerated through a wall. The air bags deployed. There were no injuries and a police report was filed. The vehicle was towed to the contact's residence and later towed to geico. The front end of the vehicle was replaced. The dealer diagnosed the brakes. The manufacturer was notified. The approximate failure mileage was 51,000.
The car randomly loses power along with the power steering and cuts off. I could be driving for 30 mins and it'll be just fine then out of no where it may cut off at stop light, while i'm decelerating or even trying to gas up. It has cut off numerous times on the highway without any warning or light and i'll only know by the sudden loss of power steering or noticing the rpm gauge dropping to 0. Sometimes it'll start up just fine right afterwards like nothing happened and sometimes it'll take a minute or two to start up. It may start a right back up then cut right back off or it may start up and be fine until the next day. Sometimes it only starts back up when i disconnect the negative battery terminal for a few seconds.
The contact owns a 2012 chrysler 200. The contact stated that the radio shorted out several times and the vehicle stalled. The vehicle was unable to restart and was towed to the contact's residence. The vehicle was then towed to atlanta west chrysler dodge jeep ram (1251 thornton rd, lithia springs, ga 30122, (770) 942-1102) where it was diagnosed that the motor failed to function, and the engine assembly and battery needed to be replaced. The contact was uncertain if the failure was related to manufacturer recall campaign number: l33. The vehicle was not repaired. The manufacturer was notified of the failure to determine their guidelines for the repair. The approximate failure mileage was 93,800. .
Under normal driving conditions all of a sudden the vehicle accelerates on its own. The engine stalls and loss of steering. The electronic throttle control warning light comes on and blinks, as well as the engine light and the traction control light comes on. Acceleration is only at 20% of what it normally is with intermittent thrust of power followed by engine failure. This lasts for several miles then the problem seems to disappear. Chrysler has no idea a out this problem with there vehicles and if u take it to an auto repair place. It saysthe vehicle is fine when they plug it in. I did some research on this to find out what to do and the internet is swamped by people with this car, this same year or around the same year... With the same problem. This vehicle is unsafe. Logic suggests that chrysler wont voluntarily recall this vehicle for financial reasons which is understandable but at the same time i don't wanna die because i cant control this car when it has the above mentioned "episode".
I have a 2012 chrysler 200 touring v6 bought it brand new. While driving on the highway taking the off ramp i engage my brakes before i get to the traffic light also engaging my turn signal. As soon as the turn signal is engaged all my lights flicker off and on this included the dash lights, stereo and the center console everything except my headlight flicker. On a few occasions the lights have totally went off and would only come back on when the turn signal was disengaged. I had taken the vehicle to a mechanic who tested my battery and alternator also checking all the fuses. He was at a lose to explain why the [xxx] was doing this. I also contact the dealer who sold me the vehicle and gave me the run around stating that they had not heard of any other vehicles doing this and dismissed my worries with saying its is your battery and or alternator.information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6).
I own a 2012 chrysler 200, the engine stops/fails about every two months while braking or while stopped. This is dangerous as it can stop anywhere and they might rear end the car or something. I have taken my car to the chrysler dealership 4 different times with the same issue, the first time they changed the pcm. After about 2 months the car's engine stopped while braking or while at a stoplight. The 2nd and 3rd time i took the car they did not find anything wrong with the car and gave it to me after a couple of days. The 4th time when i took the car they said that it was the battery and they put in a new battery. Well about 2 days ago the car stopped again while at a stoplight. I have not taken the car to the dealership as they never find anything wrong with the vehicle. I am tired of them not finding what is wrong with the car. I believe that i speak for many chrysler 200 owners when i say that an investigation needs to be done for the whole chrysler group, especially to the 200, which have many complaints online and none one seems to find the solution. Please investigate this for the safety of the drivers. I am so sick and tired of the mopar mechanics not finding anything. I do not know if the issue is with the pcm, computer, or engine. Please investigate.
The dealership wants to charge me $1800 to replace the tipm, but i see other chrysler models have been recalled for the same thing... Except mine hasn't. This isn't just a minor inconvenience... It's very very unsafe: 'the fuel pump not turning off and burning out'the airbags not deploying or deploying randomly'the engine stalling while driving'the starter cranks but won't start'the horn going off at random times'power windows not working'doors locking or unlocking themselvesmy wipers, horn and lights go on at random times. At times it's while i'm driving.... Sometimes it's while it's parked. The car doesn't even need to be turned on for this to happen. It's drained my battery a few times and now it's not even drivable. It started back in november, 2016, but has continued through the present. I haven't been able to drive it for the last 2 weeks.
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign numbers: 13v282000 (air bags, electrical system) and 16v668000 (air bags, seat belts) however, the parts to do the repairs were unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repairs. The manufacturer was made aware of the issues. The contact had not experienced a failure. Vin tool confirms parts not available and parts distribution disconnect.
Cruise control has a short.if i hit the steering wheel air bag it will eventually turn on the cruise.this happens when the car is in motion and usually when i am traveling on a highway which makes it dangerously distracting.the car only has 13,000 miles on it.the problem has been going on about one year.
Purchase new off the chrysler dealer lot april 2012.there are three knobs that control the heating and cooling in the car when the blower is turned to a low setting it will blow hot air regardless of temperature that is selected for example if it is sitting at 66degrees it will blow extremely hot air and only if the blower is set to max will it eventually cool down to the selected temperature. Once the cooler temperature is acquired, if the blower is turned down it will eventually go back to blowing only really hot air regardless of temperature setting.
The car accumulates debris below the windshield under the plastic tray which clogs up a drain tube which then makes the water flood back through the heater core into the passenger side of the car . Wetting the floor soaking the carpet and causing rust and black mold. I had it fixed once, but after investigation into the chrysler cars that this is an on going problem with all their vehicles for yrs now. This needs to be recalled and this design flaw fixed. Either they need to have free maintenance of this or they need to have a separate tube for rain drainage and a different tube for ac heat drainage.. It has cause depreciation of my over all resale value of this car plus caused carpet padding damage rust and possibly mold in my car.. Chrysler keeps laying back on the owners saying maintenance problem .. And charging over 500 to fix it. It's not like an owner can easily clean this area it involves take apart the windshield wipers etc
The contact owns a 2012 chrysler 200. The contact stated that when the key was turned over, the lights flickered for the gauges and an abnormal noise emitted from the fuel pump and the vehicle failed to start. The vehicle was towed to the dealer but was not diagnosed or repaired. The manufacturer was notified of the failure. The failure mileage was not available.
While driving, attempted turn was made going approx. 10mph and the vehicle completely shut down without warning lights or anything. Once shut down i am able to restart but having this issue remain is frustrating. The vehicle has been taken to the dealership several times and each time no code is found and nothing is able to be done. Having this issue can cause serious damage and is extremely dangerous especially since i have children and i fear for our safety.
The contact owns a 2012 chrysler 200. The contact stated that the vehicle alarm activated while the doors or trunk were opened. The vehicle also stalled numerous times without warning. In addition, the headlights failed to illuminate while driving at night. The door ajar warning light illuminated while the doors were closed. The vehicle was taken to the dealer on several occasions where the electrical module was replaced, but the failure persisted. The manufacturer was made aware of the failure. The failure mileage was 3,875.
When i turn on the fan when using the heateror the air conditioner there is a noticeable clicking sound coming from the dash on the passenger side of the car. The sound at this time is lasting about 30 seconds or so then stops. This happens when driving or standing still.
Engine light came on, had battery replaced since the battery was about 6 years old.car has only 29582 miles on it.seemed to fix then while driving 3 miles later battery light came on again. Decided to take to dealer the mext morning. Then while driving to dealership the car began to rapidly lose functionality while warning lights were appearing on the dashboardone by one until it car lost power while driving. The time from no warning lights to complete loss of electrical functionality was approximately 2 minutes.the shut down included an abrupt loss of power steering and braking capabilities while driving on a busy street during day. I was able to quickly compensate for the loss of power steering and braking and stop the vehicle while drifting into a gas station parking lot. Attempts to restart the vehicle involved no clicking or the engine attempting to turn over.had car towed to dealership.i can only assume ot may be the alternator since battery is brand new now.i am wondering if this is part of campaign #17v-435 but my car is a chrysler 200 3.6 engine 6 cylinder touring convertible and that recall does not show 200's on the notice.i have not gotten any recall noticies for this type of problem.. I bought car brand new. I am the only owner and faithfully take my car to the dealer for maintenance and oil changes.
Dear sir/ madam:11-08-15a fireoccurred at my house which was located at [xxx], on the above date, i parked my 2012 chrysler 200 in the garage and went to bed. Approximately 45 minutes to 1 hour after retiring, i was awakened by a loud explosion and my neighbors beating on my front door to awaken me and my 21 year old grandson.he also was sleeping in another bedroom. When both of us attempted to escape from the house through the kitchen/garage entrance, we were met my heavy bellowing grey and black smoke that prevented our exit and almost overwhelmed us.several months later, i am yet suffering from the shock and emotional trauma.because of dealing with flashbacks, nightmares, intermittent waves of nervousness, deep sadness, feelings of grief/loss, periodic confusion, digestion issues, and numerous financial concerns, i am in professional counseling.i have been unable to write this letter until now.even now, a friend is assisting me with completing this communication.this is the second contact i have had with your corporation.the first was the morning after the fire, when my son called on my behalf from his cell phone.he was informed that there was no recall of this particular chrysler 200, however there were some known problems with the gas tank and ignition systems that were built between march and november of 2012. Please understand.i lost my house, 23 long years' worth of cherished belongings, and the car i recently purchased. I lost everything in the fire.i decided that,i would rather initially contact chrysler directly.my hope is that chrysler will understand the gravity of the situation and do the right thing without going through expensive attorneys.[xxx]https://onedrive.live.com/redir?resid=cebfb7d86d50e64d!750&authkey=!aalipdbqwpwsze8&ithint=folder%2cinformation redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6).
My car engine is knocking loud when i drive, do i need a new engine..?
The contact owns a 2012 chrysler 200. The contact stated that there was no heat coming from the front passenger side vent and the defroster also failed to function on the front passenger side. The dealer (landmark dodge chrysler jeep ram,1900 s noland rd, independence, mo 64055, 1-(816) 833-2100) was contacted for routine servicing and they flushed the radiator, but the failure continued. The manufacturer was contacted. The vehicle was not repaired. The approximate failure mileage was 130,000.
On 1/12/2020 while driving home from work i turned on my right turn signal to merge and it rapidly clicked and flashed on the dash after the initial 3 normal flashes and i noticed the car in the lane next to me wasn't acknowledging my turn signal. Once home an hour later, i realized my passenger rear tail light was steadily light (not flashing) even though my car was off and my lights were not engaged and position off. I could not get my turn signal/tail light to turn off. The brake lights work fine when the brake is applied but the tail lights will not turn off. The rear signal won't work either since the light won't turn off to flash. I had to remove the light from the rear fender and unplug the light so my car won't die and plug it back in when i go to drive so i atleast have the tail and brake light on while driving. I can find no info on how to fix this and chrysler wasn't any help. The problem is still unresolved, but it did go off for just one moment, flickered and came back on when i plugged it back in the last time i drove.
Re s61/nhtsa 16v-668 i had this condition and paid to have it repaired.chrysler (fca) has been telling me for almost a year that they will reimburse me for the repair as soon as they determine the needed part. They state that they still don't have an identified repair so i have to keep waiting for my refund.that is not timely resolution.
2012 chrysler 200 engine dies without warning when driving. Restarts after 45 to 60 min. Car dies anytime, in heavy traffic on 2 occasions - no power steering, very hard brakeing and nearly causing accident. Died in freeway traffic
Brakes rotors bushingsengine has whine and what sounds like a missclicking noise on start up, clicking when turning ignition key withoht starting completely, and clicks when turning key off.salesman says he called chrysler and was told the 200 car is made to veer to the right to stop driver who might accidentally go to sleep from entering oncoming traffic. Dealership said call warranty.had this 2012 car a with 46k that was a rental for afewdays so far its engine is quite noisy.calling warranty company to make appt to have car checked out.
The contact owns a 2012 chrysler 200. The contact stated that while driving 20 mph, the steering wheel became difficult to turn. The vehicle was taken to the dealer for inspection where they stated that there was no power steering fluid in the vehicle. The vehicle was replenished with power steering fluid but the failure recurred. The also contact stated that the power steering hose exploded and needed to be replaced. The vehicle was repaired. The manufacturer was not notified. The failure mileage was 6,047. The consumer stated there were numerous problems with the vehicle, such as a coolant leak, oil leak, air condition, the cd player did not work, the power steering hose burst, the wire harness, the transmission was replaced, the engine was noisy and the seat belt on the passenger side was not properly installed.the vehicle cut off several times. Updated 10/31/13
The dashboard lights and the head and back lights will flicker on and off.the car has shut off while driviing in traffic.sometimes it doesnt start at all , i have to baqng the door and then the loghtas will come on.i put a brand new battery and altintor in the car and my nechnanic doesnt have a clue what is wrong woth it.believe it to be the computer system.
"takada recall" while driving down the road at 40 mph. I heard a chime and looked down at my instrument panel. The abs and the electronic stability control was on. Light was on for both. But instead of the esc it was the little car with wavy,jiggly lines under it. These two lights have been on constant for a good 3 weeks. It has gone out while driving a few times for a few minutes just to come back on and stay on almost all the time. There is no flashing of the lights. I don't drive every day. I drive around 5 times a week and short distances of 2 to 4 miles for the most part. There is also a whistling nice coming from the front of the vehicle. I don't think it is very safe to drive since the brakes and traction of the car are all to important part of me and my families safety. Please help with this issue. I paid and am still paying a lot for this car that now has 62000. Miles on it.
After owning my car for only a few months the check engine light came on and a minute later the electronic throttle control light and then the electronic stability control light. After taking my car to kendall dodge chrysler jeep ram 5 times, an independent auto shop once and another visit to the dealership where the car was purchased my car is still having issues shifting from 2nd gear to 3rd. At least that's what the auto shop told me the problem is, with the transmission. I hit the gas and the car clunkers and jerks like a manual car when i'm just lightly pressing on the gas. The car doesn't even have 52,000 miles. I've had it less than a year and half the time it's been in and out of repair shops.
I was driving at normal condition at 35 miles per hour, at one time, the abs and esc light come on thedashboard, there is no rain no snow, no excessivebraking or speedingor turning, since 4 days passed,the lights come on every day when engine running.updated 11/04/15
The contact owns a 2012 chrysler 200. While driving 35 mph the steering wheel ceased and the vehicle stalled. The contact was able to restart the vehicle after five minutes. While driving and making a left turn the vehicle stalled again. While attempting to start vehicle there was abnormal ticking noise detected. The abs and traction control warning lights were illuminated. Additionally, the speedometer was inoperable. The local dealer was not contacted. The manufacturer was contacted but no further assistance was provided. The failure mileage was 114,000.
While driving down the road the etc light came on and the traction light came onand the car will not accelerate. I was able to park the car and when i restarted it that was a very rough idle and the check engine light the etc light and the traction light are all on.
Under normal driving conditions all of a sudden the vehicle accelerates on its own. The engine stalls and loss of steering. The electronic throttle control warning light comes on and blinks, as well as the engine light and the traction control light comes on. Acceleration is only at 20% of what it normally is with intermittent thrust of power followed by engine failure. This lasts for several miles then the problem seems to disappear. Chrysler has no idea a out this problem with there vehicles and if u take it to an auto repair place. It saysthe vehicle is fine when they plug it in. I did some research on this to find out what to do and the internet is swamped by people with this car, this same year or around the same year... With the same problem. This vehicle is unsafe. Logic suggests that chrysler wont voluntarily recall this vehicle for financial reasons which is understandable but at the same time i don't wanna die because i cant control this car when it has the above mentioned "episode".
Takata recall, abs and traction light are on they make a funny noise when i first start the car and start driving. But after i go so far or to 25mph, my lights come on and i brake just fine. I also have a issue with my turn signals, if my headlights are off my front left turning sognal works but if my headlights are on my front left turning signal does not work.
Takata recall: there is a problem with the electronic throttle control light that causes the car to decelerate randomly, in combination with a ticking sound that comes from the air bag area of the glove box that is exacerbated by the ac and the heat being turned on.i feel that the car is unsafe to drive, although it says there is no open recall on these components.this happened several times to me on the expressway today.
2 weeks ago abs and esc light are on all the time when engine running , after i test the car they find abs module-esc module need to be replaced, how is this possible car have only 21.500 miles, cost is:$760.00 dollars, care have expired warranty in march this year, and18 more months power train warranty, i call chrysler, they say i need to pay because car have no basic warranty anymore, that is not right, so now i driving without abs even if i have money i am just scared that same abs module going to be bad after 2-3 years and i need to replace again,
This chrysler 2012 200 started to have brake squealing issues at about 7,000 miles i went to dealership and they told me that it was probably just being broke in since i purchased this car at 200 miles on it.the problem continued and no one at the dealership would address this problem.i then told them they had to do something about it and they then told me that there was not a fix for this that chrysler could not fix this problem.and that they the dealership dennis dillon and chrysler had no idea what to do.i continued to drive my car and in september of 2013 my car's check engine light came on and i took into the dealer dennis dillon and was advised that my cylander head was gone and would need repaired. I was told to go ahead and dive my car while the parts came in.my car was fixed and picked up from dealer then 1 day later my car overheated on interstate and broke down was then told a clamp came off and was then fixed.since this issue my car has not driven the same. It is sluggish . I asked the dealer about the lemon law and was told to contact chrysler . I did so and was told by chrysler that there is nothing anyone can do. My brakes still sqeal very loudly and chrylser told me that its becasue they replaced the brake pads and no longer have asbestos' in them.i then advised them that i have driven other models and makes and did not have that problem.they refused to be of any assistance. My steering is also an issue in which the dealership has said that it needed an alignment but since the car was only a couple hundred miles on it.it has pulled severly to the left. This is not acceptable and this car needs to fall under the lemon law and be dealt with.
The car stalls out!!!check engine light comes on and the car stops on the highway!!i was driving at a low rate of speed and the car just quit. It refused to start for about 5minutes.
The electrical throttle light keeps coming on and the car shuts off.
While driving the car.. Thecars electrical system stopped working. While driving on the freeway the car shut down and was almost in severe car accident because of the issue.there is a new battery and the alternator has been checked and is in great working condition.
Car was in motion leaving a shopping area, turning right and accelerating onto a 4 lanehighway.as 45 mph was achieved, the car decelerated and stalled.the check engine light and the electronic throttle control light came on.i looked up the etc information and read i may be able to try again to drive the car.i did try and rolled on the shoulder for about 1/4 mile before having to accelerate though an intersection.at that point, car repeated the above failure and stalled.i was able to make a right turn and coast into a parking lot.the car was towed.while waiting on the tow, i read several reports of the same issue occurring in this model vehicle, often while driving on the interstate or in other dangerous locations like an intersection.this failure happened with no warning - no sputtering, hesitation or warning lights until the failure occurred. This failure could result in serious injury or death.it looks to me to be a known issue and should be subject to recall.
2012 chrysler 200 shut off while driving (slowing down coming to a stop sign) with no warning.all power was gone.this happened in july of 2015 and tipm was replaced under extended warranty.told another faulty tipm and was replaced under part warranty with no cost to me.any time a vehicle shuts off without warning while driving is extremely hazardous!first time vehicle had approx 65,000 miles.this time approx 80k
Excessive "fish tailing" in minimal snowy conditions, very unstable, absolute death trap. I felt like i was going to end up smashing into a passing car or truck . Drove for 30 miles per hour for 260 miles while there wasn't more than one inch on snow on the ground because the rear end of the car was swing in all directions, my wife and daughter terrified. I just bought the car back in august 2013 thus a few months ago and had no issues driving on dry ground but only in snow and wet conditions.
When purchased this car, noticed that it pulled severly to the left,spoke to dealer ship and they stated that it was normal for front wheel drives to do so.so i continued to drive this car but always having to be on alert when driving on highway if car was going to jerk off road. This car handles horrible! i do not feel safe in this vehicle and do not feel if any control was lost, that i would be able to regain control due to this.the dealership has denied that i have ever brought this up, but when my brakes started squealing around 7000.00 mile i then brought it up again and they told me i needed a front end alignment and new brakes! ok i just bought the car... I told them no, how could that be.well since then my car has had to have the cylander replaced and they have addressed the jerking with a front end alignment which by the way did not do anything. It still is hard to control and could only do 30 mile an hr in snow before it would loose control. I have more complaints and have addressed chrysler to no avail. They just tell me its the make of the car and that my brakes squealing are because asbestos is no longer in brakes. I told them that i was not born yesterday and have driven more cars than this and never have had this problem. They offered me an extended warrenty and stated that was all anyone could do .i am a very unhappy customer and becasue i am in a lease i can not get out of this car. Only when it crashes will anyone maybe do anything about this.i am seeking the state attorney in idaho to see if they can help resolve this issue .
"takata recall" the issue is in the electrical warning system. The warning indicates air bag. Air bag light is on and has stayed on continues to stay on. It does not flash it just stays on. On the start of the vehicle once the ignition switch is turned on and the car is running. It continues to stay on while vehicle turned on and running. I believe it may be a recall with the modular.
Car shuts off while driving with no warning signal
Stopped at a red light, up until then car was driving fine, made a left turn and the 200 loss power and stalled out. The etc light and traction control light came on out the corner of my eye, next thing i know i was plowed into by another car. After doing more research, i have seen this problem come up time after time. The electronic throttle actually has plastic gears, plastic gears that control the opening of the throttle valve im sure those teeth will wear out on nearly every car and cause problems.
Transmission goes in to limp mode,does not go over 30 miles jerking speeding up and slowing down, won't start and check engine light comes on goes off.
The car consistently stalls out at least 4-6 times a trip in the middle of driving, if not more. It also honks on its own during that time.it was brought to the dealership and a shop and they couldn't find anything wrong
The contact owns a 2012 chrysler 200. The contact stated that while driving at 70 mph, the headlights failed without warning. The contact also stated that the traction control, the cruise control and the abs warning lights were illuminated. The contact also stated that there was a grinding noise coming from the front of the vehicle. The vehicle was not taken to be diagnosed or repaired. The manufacturer was notified of the failure. The approximate failure mileage was 112,000.
I bought this car use with 27,000 mile on it. I have only had the car for 45 days or so. My car is jumping forward when i come to a stop. At first the lurching was very faint now at 31,000 miles the lurching is more pronounced.i took the car to the dealership prior to the warranty ending and they acted like they where unaware of the issue/or didn't understand the issue.any way i am beginning to feel unsafe since it is happening more.the car lurched forward during a sudden stop one time, not good.
The contact owns a 2012 chrysler 200. While driving at an unknown speed, the electronic stability control warning indicator illuminated. The accelerator pedal was depressed, but the vehicle failed to respond. The vehicle was towed to oxmore chrysler dodge jeep ram (4520 shelbyville rd, louisville, ky 40207, (502) 895-4520) where it was diagnosed that the electronic stability control module needed to be replaced. The vehicle was not repaired. The manufacturer was not notified of the failure. The approximate failure mileage was 40,000.
No heat/ defrost passenger side. Will not clear frost/ fog on passenger side windshield. Apparent known problem with sludge build up in heater core allegedly caused by component in coolant.
In march 2014 owner noted a problem with the hvac system - no heat was delivered to the passenger side air vents or heater vents in cold weather. During routine oil change mechanic noted severe discoloration of engine coolant and buildup up sludge in coolant expansion tank. Took vehicle to dealer for diagnosis. Dealer stated that the coolant had been contaminated with the addition of the wrong type of coolant. Per chrysler star # s1207000008, dealer flushed coolant system multiple times and commented that if that didn't work they would have to replace the heater core, radiator, oil cooler, and expansion tank. When repairs were completed owner noted that the temperature output from the air and heater vents was 20 degrees lower on the passenger side than the driver side. Dealer stated that repairs were complete. Owner is in process of contacting chrysler to have heater core and radiator replaced.
Passenger side pushes out cold air, terrible to drive in and uncomfortable. Battery has been replaced 4 times in the last 2 years. Alternator as well. While driving to work, my windshield frosted over from being so cold and i had to veer off the road to avoid getting into an accident.
Entering freeway was accelerating,merged into a lane and took foot off of the accelerator and the car rpms kept climbing and speed kept increasing within 10 seconds it stops and will respond normally usually happens when there is a quick attempt to accelerate.
This car was bought new with approx 300 milesbrought from a dealer's inventory in kokomo, in to one in northern kentucky, where it was bought 11 may ,2012..it had been on the previous dealer's lot, as part of inventory, i believe since sep,2011. In total it has stalled while stopped at a light 2 separate times..twice it has either quit while slowing or downshifted causing quite a violent throw forward of persons in their seats while at a relatively slow speed coming to a stop...in the old days it would be the jerk you get while popping a clutch to get a car started with a bad battery.. The third time it stalled was backing out of our driveway...we are now approaching 1000 total miles on the car with less than a month of ownership...made first visit to a dealer service 30 may 2012,..pcm code was updated,but could not duplicate problem..have had one jerky downshift since then ..this has been the recurring theme of many of these instances written up on blogs concerning this model over last 2 years..side note..this car has remote start capability on the key fob..i noticed a recall last year for some vehicles where they noticed the circuit board inside a fob had vibrated loose, and somehow was sending signals to some component in the car which was causing it to stop...ie. No codes associated with a malfunction like that...might be something to look at too.twice also, the hint of an electrical smell has been detected...same smell i experienced when the pcm on my 1993 ford van cooked itself a couple years ago..at first i wrote it off as a new car thing..but combine that with present and past experiences...well, the connection may not be coincidental.
Today, while on the interstate traveling at 60mph, attempted to accelerate and car would not accelerate. Could hear the engine trying to accelerate but the car kept slowing down. Did not see any lights (engine) light up on the dash to indicate a problem. Pulled into emergency lane, stopped and turned engine off; restarted car and it has not occurred again today.
Passenger side heater stopped working. Vehicle turns off while in drive and moving.
The contact owns a 2012 chrysler 200. When the vehicle was started, the check engine indicator illuminated and remained lit. The vehicle was taken to an independent mechanic who dianosed that the catalytic converter needed to be replaced. The dealer and manufacturer were not made aware of the failure. The vehicle was not repaired. The failure mileage was approximately 196,000.
Transmission is going after just 8 years old!!!!!
The contact owns a 2012 chrysler 200. The contact stated while driving 70 mph, the vehicle stalled with the check engine warning light illuminated. The vehicle was taken to hanford chrysler dodge jeep ram (369 n 11th ave, hanford, ca 93230) where it was diagnosed with the engine needing to be replaced. The vehicle was not repaired. The contact related the vehicle to an unknown recall. The manufacturer had not been informed of the failure. The failure mileage was approximately 80,000.
Brakes rotors bushingsengine has whine and what sounds like a missclicking noise on start up, clicking when turning ignition key withoht starting completely, and clicks when turning key off.salesman says he called chrysler and was told the 200 car is made to veer to the right to stop driver who might accidentally go to sleep from entering oncoming traffic. Dealership said call warranty.had this 2012 car a with 46k that was a rental for afewdays so far its engine is quite noisy.calling warranty company to make appt to have car checked out.
I just had my car pre purchase inspected and it was reported to be in great condition. Then all of the sudden my engine has stalled twice in the last 72hours, when coming to a stop. I am able to turn it back on, however fear for my safety now whenever i drive it.these exact issues have been reported with other 2012 chrysler 200 models, due to connecting rod bearing failure and i believe this model has been similarly effected. I feel like i should be entitled to a engine recall as well, due to the identical issues that i am experiencing.
The first time this incident occurred i was preparing to make aleft turn off of a busy road. I had just purchased the car and not really thinking something was wrong with my vehicle when the engine stalled. This incident has occurred very often since september of 2012. I have taken my vehicle to the dealership three times for the car stalling and cutting off during low speeds. I'm suppose to take it back again tomorrow but i'm very disappointed to know by reading other complaints the problem will not be fixed. It's very sad someone or multiple people have to die before anything can be done about these cars. I have four kids and i am terrified for them to ride in the car with me. These cars are definitely not safe to be on the highway! someone please offer some help!!!
Still not fixed. Cleaned throttle body, and when that didn't resolve the issue they replaced throttle body. Car still stalls at random times, both while moving and waiting at lights. Almost been in several accidents. All loss of power steering and control of the car.
The vehicle shut off on me after making a brief stop in traffic. And then again while actually driving. The next day it shut off on me after a stop sign. Absolutely no prior warnings were given of any problems. Now the ck engine light comes on intermitantly. The stops cause loss of power steering and control of vehicle.(busy city street).
The contact owns a 2012 chrysler 200. While driving various speeds and shifting gears, the vehicle shut off without warning. When the vehicle was shut off and restarted, it resumed normal operation. The contact took the vehicle to steve landers chrysler dodge jeep ram (401 colonel glenn plaza loop, little rock, ar 72210, (501) 404-9103) where it was diagnosed and an unknown part was repaired. The diagnosis and repair specifics were not disclosed. The failure recurred after the repair. The manufacturer was not notified of the failure. The failure mileage was 105,000. The vin was unknown.
The contact owns a 2012 chrysler 200. The contact stated that while driving 80 mph, the vehicle stalled without warning. The steering became difficult to maneuver. There was an abnormal odor of radiator fluid detected in the vehicle. The vehicle was towed to the residence. An independent mechanic went to the residence, and diagnosed that the head gasket was blown. The vehicle was not repaired. The local dealer and manufacturer were not contacted. The failure mileage was 116,000.
Engine keeps shutting off in traffic, at stop sign. Check engine light keeps coming on and off. Car shut off on me in middle of trafficwhich put me at risk for being in a bad accident. This is my only means of transportation and i fear for my stay everytime i'm drivingmy vehicle.
I was driving around 40-50 mph when my vehicle shut down for no reason and with no warning. The only warning was after it shut down and the engine light came on. I had to swerve out of traffic with no power steering and turn the ignition to off. That i started it back up and it drove fine but with the check engine light still on. I have read numerous complaints about this and about dealers doing nothing about it. Some complaints involving injuries and children. Something needs to be done about this because i am now stuck with a lemon that is not worth what i owe.
The car randomly loses power along with the power steering and cuts off. I could be driving for 30 mins and it'll be just fine then out of no where it may cut off at stop light, while i'm decelerating or even trying to gas up. It has cut off numerous times on the highway without any warning or light and i'll only know by the sudden loss of power steering or noticing the rpm gauge dropping to 0. Sometimes it'll start up just fine right afterwards like nothing happened and sometimes it'll take a minute or two to start up. It may start a right back up then cut right back off or it may start up and be fine until the next day. Sometimes it only starts back up when i disconnect the negative battery terminal for a few seconds.
The contact owns a 2012 chrysler 200. The contact stated that while driving at various speeds, the vehicle stalled without warning. The contact stated that on several occasions, the vehicle failed to restart. The vehicle was taken to an independent mechanic who replaced the alternator however, the failure recurred. The cause of the failure was not determined. The local dealer and manufacturer were not notified of the failure. The failure mileage was unknown.
The contact owns a 2012 chrysler 200. While driving approximately 72 mph, the engine stalled without warning. The contact lost control of the vehicle, veered to the left, and crashed into the plastic dividers. The vehicle was able to restart and the check engine warning indicator illuminated. A police report was not filed and there were no injuries. The vehicle was taken to a dealer where it was diagnosed that the vehicle had low oil and the central module needed to be reset. The vehicle was repaired. The manufacturer was made aware of the failure. The failure mileage was approximately 32,000. The vin was unavailable.
So two weeks back on on sept. 19 my car broke down... Which i don't get because dealership said due too improper lubrication in the engine, always changed my oil and filter and coolant or anything needs to be replaced at said mileage. Also in told me cylinder 4 by dealership was my problem till it blown always kept oil same and heard about it never tried to drive it till i found out why i have this problem... Was told s.o.l !!! so now have no car to get my kid or work walk and ask for rides and still making payments for this only have 109,614 miles on for something that should of happened at 200,000 miles or more i take care of my car thing was my joy for work or my kid so please help me understand why....
Car randomly while driving 'shimmies'. The whole car will shake.
I was driving along that morning into work when my battery light came on. I then proceeded to call around to find out what was going on. Later that afternoon my car complete stopped working and was "freaking out" on me while i was driving. After coming to the conclusion that it was not my battery that died, it was my alternator that stopped working. Now my vehicle is sitting in the front of my house not wanting to start up.
The contact owns a 2012 chrysler 200 convertible. While driving various speeds, the vehicle suddenly shut off. The vehicle was taken to an unknown dealer who was unable to determine the cause of the failure. The manufacturer was notified of the failure. The failure mileage was 58,000.
The contact owns a 2012 chrysler 200. The contact stated that while driving approximately 10 mph in a parking lot, the engine stalled. The contact was unaware whether a warning indicator illuminated on the instrument panel when the failure occurred. The engine restarted and resumed as normal. The vehicle was not repaired. There was an open investigation under nhtsa action number pe12016 (engine), which pertained to the 2011 model year vehicles equipped with 3.6l engine. The manufacturer was not notified of the problem. The approximate failure mileage was 1,150.
I was driving my 2012 chrysler 200 and it stops in the middle of the road suddenly with out any warning. It happened to me 8 times in a row now with in week. I just see a check engine light on in the dashboard and the engine shuts off completely. If i try to restart the car it starts only after turning the car off for few mins. I had it checked a couple of times with a mechanic but they are not able to fix it. Driving this car is not safe as it stops in the middle of the road and locks the steering as well.
Shifted the vehicle into reverse, when the vehicle is then put into drive there is a loud bang.
I have reported in the past in regard to our 2012 chrysler 200 with 3.6 v6 engine of episodes of pmu shut down while driving at slow speed.the manufacturer warranty still covered the vehicle when we first experienced this problem we now are over 60,000 miles as chrysler has not been able to resolve this problem yet.the engine quit while driving (3 times additional times), at highway speeds.we were able to get to the shoulder of the highway , without power steering and brakes;all computer support systems failed, but all electrical systems still worked. The problem has been checked 4 times after each of the stalling episodes, the pmu computer shows no codes (per chrysler and the dealer) there is no problem to fix.the last episode the esc dash lite came on, followed by the brakeand the abs lights started flashing on & off which caused the speedometer to bounce up and down while the ability to maintain speed or accelerate to maintain speed was lost(again there were no codes) the last2 times this happen were 11/30/16 & 12/1/16.i have talked to chrysler fiatbut the dealer ani i have not been able to receive any service or suggestion in resolving this pmu problem.it feels like they are not concerned that there is a great safety issue that could result in injury or death. There should be some information available, as this has been a problem thathave been ongoing for many models with the 3.6 v-6 engine and over a number of years, which chrysler has issued customer service notices to dealers and replaced pmu. Recalls have been avoided as there has not been any serious accidents, injuries, or deaths. If you have had this type of problem with your 3.6 v6 contact chrysler and the nhtsa.
While driving down the road the etc light came on and the traction light came onand the car will not accelerate. I was able to park the car and when i restarted it that was a very rough idle and the check engine light the etc light and the traction light are all on.
Sludge build up in the cooling system has caused loss of heat to the passenger side and is due to a known issue with this vehicle caused by the manufacturer putting in the wrong coolant.
The contact owns a 2012 chrysler 200. The contact stated that the radio shorted out several times and the vehicle stalled. The vehicle was unable to restart and was towed to the contact's residence. The vehicle was then towed to atlanta west chrysler dodge jeep ram (1251 thornton rd, lithia springs, ga 30122, (770) 942-1102) where it was diagnosed that the motor failed to function, and the engine assembly and battery needed to be replaced. The contact was uncertain if the failure was related to manufacturer recall campaign number: l33. The vehicle was not repaired. The manufacturer was notified of the failure to determine their guidelines for the repair. The approximate failure mileage was 93,800. .
In traffic, steering wheel tightened up and all interior lights were off. Tried to brake but no response, shifted into neutral restarted the car and it turned back on. Seemed to mess up the shifter a little in the process, as well as almost hitting the car in front of me. Probably going about 10-15 mph, and i was lucky to throw the car in neutral and restart otherwise i would of floated into an accident.
Submitted a complaintwhere i inadvertently listed my vehicle as a 2015 chrysler 200.my car is a 2012 chrysler 200.could you change my previous complaint of this same date to reflect a 2012 chrysler 200.
The contact owns a 2012 chrysler 200. The contact stated that there was an abnormal noise coming from the front end of the vehicle. The vehicle was not diagnosed or repaired. The manufacturer was made aware of the failure. The failure mileage was unknown.
Car dies for no apparent reason and during any type driving.of course, when motor dies power steering is lost.extremely dangerous in the heavy austin traffic that i drive in.may just shut down on a major overpass with no where to go.this vehicle puts my life and families life in danger.this shut down can happen at 10 mph or at 60 mph or above.i try to bypass major highways in austin even though it may be several miles out of the way, and so far have been able to avoid any problems.it seems ridiculous to have to travel like this.my car engine is a 2.4l and i know there has been a recall on chrysler's 3.6 l engine in the 200, but i believe this engine needs to also be recalled
The contact owns a 2012 chrysler 200. The contact stated while driving approximately 30 mph, the vehicle stalled without warning. The vehicle was restarted. The vehicle was towed to pine belt chrysler dodge jeep ram (401 broadway dr, hattiesburg, ms 39401, (601) 544-2430) however, the vehicle was not diagnosed nor repaired. The manufacturer was not notified of the failure. The failure mileage was 89,841.
This is a problem that started with the prior owner of the vehicle but the connecting rods in the engine are failing the hazard switch does not work and the traction control does not work i noticed atleast the connecting rod was a safety recall and vin specific it was noticed when the cam shaft started making noise due to debris
System heating. When turning on the heat, the system blows cold air on two mid air vents and the passenger side vent. The only heat that is felt coming from drivers side vent. Brown or tan sludge in recovery tank and on radiator cap
For weeks now ive been noticing a weird grinding or dry rubbing sound underneath the front end of my chrysler. Checked it out a few times, as though i am not a mechanic i can identify the basics of something not right. However, after my husband and his brother both looking it over on seperate occasions, they have noted a leak under the carriage of the car. Often here recently, the guage senses an over heating of some sort. Since this notice, we have replaced the oil cooler twice in a year; as well as flushed the hoses associated with the coolant reservoir. Fixed temporary but has now already started getting too hot. Which simply tells me that its something further internal thats wrong. I was informed of an engine recall: l33 of my chrysler model. However havent seen one on this website. When driving yesterday, i noticed a light on my cluster that indicated the traction has failed. When i brake, all u hear or feel is a vibration under your feet, up front. I replaced my brake pads all 4, within the past 4 months and theyre now rusted over and u notice a brake fluid leak on the front right side. After a light, the grinding noise, the vibration and the overheating; i am positive that this will eventually cause a car stall or worse a fatal accident. My brakes could eventually fail while driving in traffic, causing a crash. Or my car could just all out stalland the cluster can trip and i could be in harms way if at the time it does this i could be goin 70 on the interstate or in a turninglane in town and without proper fix; it could easily cause a fatal accident and i could be killed or worse my children!
The car won't stop overheating, we have replaced thermostats and pumps thinking there was a leak but that never stopped the problem. 20 seconds after starting the car the engine is already at the halfway mark for how hott it is, and even goign 30 miles an hour get all the way to the top and starts overheating. On my way to work i almost crashed cause it showed no indicators at al!!! just starting bellowing smoke. So i pulled over and turned it off and didnt move it.
While taking off from a stop light. The 2012 chrysler 200 cut off with no warning (no stalling,sputter, hesitation of the sort). I was stopped not on the hwy but a major divided four lane hwy. (ga 54, newman, ga at the intersection of u. S. Hwy i-85). After several restart attempts. The vehicle restarted with the engine malfunction light illuminated. This vehicle only had 45,466 miles on it with all maintenance up todate being completed by the chysler dealership purchased from. Dealership notified, appointment scheduled for 3-26-2015. Who wants to drive a vehicle with a defect that the manufacturer is well aware of. Just look at the amount of complaints.
This car was bought for advertised miles per gallon (mpg) was 31mpg, but on the highway it is only getting about 15mpg. This car is either defective or chrysler has embarked on major false advertising or fraud campaign in which millions of people bought this car thinking they would get 31mpg, but are paying twice as much in gas instead of saving money. If you think you are getting 31mpg on highway, but only get 15mpg, that means you run out of gas on the highway and an accident can occur either while the car is slowing down in the lane, or after it is pushed into shoulder, which is still dangerous. There are hundreds of reviews on the internet with same problem - not getting gas mileage. Please force chrysler to take back these cars because it is either false advertising and consumer fraud for advertising 31mpg, or defective for failing to be efficient with gas mileage since they are not getting the performance these cars were supposedly manufactured & designed for. There are also unknown problems with transmission and engine. I'm taking car to dealership today to investigate/service, but i was told by the sales manager, they would not take the car back and give me a new car. It has all these problems, costing me money and possible injury due to the prospect of running out of gas so frequently!the gas tank size is 16.9 gallons, so at 31mpg, i should get close to 523 miles, but we only get about 250!we fill up gas tank every week, after only driving 36 miles roundtrip to/from work, mostly on highway. I believe we are being defrauded by being sold defective cars that do not perform as advertised, and which can cause injury as a result. I shouldnt be stuck with this car, paying excessive gas prices due to constantly refilling a gas tank, because this car burns up all the gas so fast! is it a defect or consumer fraud? i want this car recalled, and i want my money back!
The car stalls out!!!check engine light comes on and the car stops on the highway!!i was driving at a low rate of speed and the car just quit. It refused to start for about 5minutes.
Takata recall the tipm has malfunctioned car will not function of start
My vehicle stalled for the first time of over 100x on may 19, 2019 just as i was entering a highway. It has since stalled driving in highway traffic fast and at red lights.as a matter of fact it just happened again as i write this complaint.
The contact owns a 2012 chrysler 200. While driving 40 mph, the electronic throttle control light illuminated. The vehicle slowed to 20 mph and went into limp mode. The vehicle was taken to the dealer to be diagnosed. The contact was informed that the electronic throttle control module needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure. The approximate failure mileage was 94,200. Udated 07/26/16*lj.....updated 08/01/16 consumer stated the vehicle ceased to accelerate on a busy street. Consumer was informed that every sensor in the electronic system was malfunctioning, which caused dealer to be unable to accurately diagnose the problem. Repairs not covered by warranty. Consumer noted chrysler issued a recall for the same exact issue on 2015 chrysler 200 model.updated 06/13/18
The contact owns a 2012 chrysler 200. The contact stated that the heat and defroster stopped working. The vehicle was taken to landmark dodge chrysler jeep ram (1900 s noland rd, independence, mo 64055) four times, and each time the heater cooler was replaced. The manufacturer was contacted and did not assist. The vehicle was not diagnosed or repaired. The failure mileage was 78,000.
The contact owns a 2012 chrysler 200. While driving approximately 10 mph, the engine stalled without warning. The contact required a jump to restart the vehicle. The engine started and the instrument panel illuminated, but the failure recurred. The vehicle was not diagnosed or repaired. The manufacturer was made aware of the failure and advised the contact to take the vehicle to a dealer. The approximate failure mileage was 56,000.
When driving the vehicle will suddenly shut off. No warning of it about to happen just does. I lose steering and brakes and turns on only after time goes by or by removing negative terminal from battery. It's happened at 35mph and at 60 mph. I've gone a week with no incident to having it happen dozens of times on a single trip. Very scary situation. Especially in traffic.
Totally integrated control module has failed leaving my car unable to start and once started have lurches in acceleration. Will crank but not start.
While accelerating after crossing a busy state highway the car "jerked" and the malfunction indicator light came on. (prior to this i was idling at a stop sign and i proceeded straight across the road. )i was in the process of immediately moving to the side of the road when the car lost all power and shut itself off.i did not initially try to restart the car but once i returned to it in a couple of hours i was able to start the engine.the indicator light remained on.i did not drive the vehicle but had it towed to a service station.the car has less than 80.000 miles.
My chrysler 200 was purchased about two months ago since i purchased it from florida and i reside in alabama i was told by the local dealership in mobile that they could not diagnose or repair it because they have no history. My car is randomly stalling and loosing all power to engine when attempting to stop or slow down there is no codes on dashboard. Pcm was replaced still same issue. It is very likely this will cause an accident especially because there is no warning. It cut off tonight on my way home from work while i was driving at 35mph. This is dangerous
Pulled off interstate after driving for 2 hrs. Into parking lot.started to pull into parking space and everything thing locked up.no steering, no breaks,everything died except lights on dash. Car was driving fine with no indication of problem. I am told that my car does not fit into the recall for engine failure for this model.concern with safety as if i hadbeen on interstate going 70mph this would have caused a bad accident.
The car will almost stall, randomly, when stopped at a stop sign or light. It has now started to act like it is going to stall when we start it. The car hesitates, randomly, when you go to accelerate.this has happened to us many times. Entering the interstate it acts like it stumbles before it will respond.we have pulled out onto a busy street where acceleration is a necessity and the car hesitates and almost caused an accident.most recently, switching lanes on the interstate we lifted our foot off accl. To allow a car to pass us when we went to accelerate again the car would not respond, a car came up on us in our lane and almost rear ended us. (this was on the way to the dealership for the problem) the dealer has been unable to duplicate the issue and nothing was recorded on the computer. Many complaints about this issue on chrysler 200 forums. We have had a blk box installed and no feed back from dealer was provided even when requested in writing and verbally. We have an attorney, chrysler has put a low value on the complaint and we are not going to settle case at this time. I hope we do not have an accident while collecting data!
The contact owns a 2012 chrysler 200. While driving various speeds, the vehicle stalled without warning. The vehicle was able to be restarted and resumed normal operation. The vehicle was taken to the dealer numerous times, but a failure code could not be located. The manufacturer was made aware of the failure. The vehicle was not repaired. The failure mileage was 35,460.
Driving vehicle to investigate symptoms and during regular casual driving the car stalled, hydraulic brakes went and steering locked while slowing through a school zone. I'm a certified tech with h-d, kawasaki, bmw, and have never had a service manager deny a request that involved serious systems like this until today. That is why i'm filing this complaint on your site, i was told by the s.m. That they couldn't get my 29 day old 200 in before next week monday! this is not a safe car, anyone reading this please do not buy this car!!!! mdm.
Vehicles stalls while driving randomly, this could be 5 minutes or 2 hours after vehicle is driven, and after vehicle sits for a while, 1/2 hour to an hour, vehicle starts right up with no check engine light or any history/pending/current codes..dealership has already replaced the fuel pump but problems persists.have seen many similar cases of this vehicle stalling and then it starts right up after sitting for some time.
There is no heat on the passenger side of the vehicle.chrysler service diagnosed the problem as a blockage in the heater core.they advise that they needed to replace the heater core, radiator, oil cooler and flush the system.this work was estimated at $2,700.i took the car to another shop and had the heater core replaced, the cooling system flushed and a manual flush on the engine block.this fixed the problem for more than half the cost.there are a lot of complaints about this same issue and it is a safety hazard if you cannot defrost the windshield when necessary.i believe you can be ticketed for not having safe visibility when operating your vehicle so this is defect that that chrysler should consider issuing a safety recall for.my car only has 72,000 miles so it's hard to believe that a major component like the heater core would be damaged and not work properly.
The contact owns a 2012 chrysler 200. While driving 50 mph with the accelerator pedal depressed, the speed reduced independently to 5 mph. The vehicle stalled and the throttle body and abs warning indicators illuminated. The vehicle was able to restart on the first attempt. The vehicle was not diagnosed or repaired. The manufacturer was made aware of the failure. The failure mileage was 84,000.
The contact owns a 2012 chrysler 200. The contact stated that the engine failed and the engine stalled while the steering wheel was turned to the left. The vehicle was taken to al serra chrysler dodge jeep ram (6185 south saginaw street grand blanc township, michigan 48439, phone (810) 503-4925), but a diagnostic was unable to locate a failure code. The dealer advised that the failure could be due to low fuel. The vehicle was not repaired. The manufacturer was not notified of the failure. The vin was not available. The failure mileage was 78,000.
It started yesterday morning july 5th 2017, as i was driving 45mph to work my car just shut off with no warning.. It happened twice.. Today july 6th on my way home taking a right hand turn my car shuts off again, no warning.. Tried starting it which it started but then notice the engine light was on and my oil light came on saying needs oil change.... I still have over a thousand miles before my next oil change is due... Later that day i checked my oil which was good, didn't need any.. I'm just confused on what's going on especially when i just paid $6500 to pay the car off...
2.4 liter 2011 chrysler 200.when slowing then accelerating in left turn lanes and turn abouts, the 200 will often stall for a second or two, then proceed.seems to especially happen when attempting to increase speed quickly to enter traffic.the engine will stall and become unresponsive for a second or two before responding again.the entire process is that i brake and slow for the turn or to enter a round about, when there is an opening, i accelerate, the 200 will speed up as expected, then the engine will suddenly stall and become unresponsive for 1-2 seconds, then resume as normal.this has been unsettling a couple of times.this seems to occur when turning and accelerating.i do not have any issues when accelerating in a straight line.the second speed issue is that the 200 is slow to stop revving when accelerating.on several occasions upon acceleration, when i lifted my foot off of the accelerator, the engine kept revving for a couple of seconds and the car kept speeding up.this has not caused any safety issues.it only happens when i accelerate quickly.when driving normal, this issue does not occur.
I bought my 2012 chrysler 200 in 2013.i 've had a recurring problem with the engine running hot because some malfunction prevents the coolant from circulating through the engine.i have spent over $2000.00 trying to fix this problem and now my mechanic tells me the engine is no good and i'll need a new one.this happens when i'm driving. The car would run hot, i'd tow it in and my mechanic would fix it. And within a month or two, the problem would occur again. My mechanic ran diagnostics, he rebooted the computer systems and he gets the coolant flowing again but within weeks or a month the same problem reoccurs. I don't drive far to work approx. 10 miles daily commute.i may take a road trip on occasion but there is no unusual wear or tear on the vehicle. Im reporting this problem aug 2016 but this has been a recurring issue overthe years and the car is just for years old.i bought it used in 2013. I've spent so much money fixing the same problem and the car's problem always seems resolved until a few months down the road i have to fix it again. I haven't even paid the car off and its kaput and ready for the graveyard? this really is something chrysler needs to step up to the plate and fix.i need a new engine now and i've already spent over $2000.00 trying to fix this issue.
Under normal driving conditions all of a sudden the vehicle accelerates on its own. The engine stalls and loss of steering. The electronic throttle control warning light comes on and blinks, as well as the engine light and the traction control light comes on. Acceleration is only at 20% of what it normally is with intermittent thrust of power followed by engine failure. This lasts for several miles then the problem seems to disappear. Chrysler has no idea a out this problem with there vehicles and if u take it to an auto repair place. It saysthe vehicle is fine when they plug it in. I did some research on this to find out what to do and the internet is swamped by people with this car, this same year or around the same year... With the same problem. This vehicle is unsafe. Logic suggests that chrysler wont voluntarily recall this vehicle for financial reasons which is understandable but at the same time i don't wanna die because i cant control this car when it has the above mentioned "episode".
Vehicle engine light went on.unable to accelerate.vehicle stalled and pulled over to side of road.happened 5 times in 16 mile trip.this occurred when vehicle has 18-20000 miles requiring towing of vehicle.at that time, repair involved wiring repair and replacement of sleeve.the problem has clearly recurred.this is a safety issue.
The contact owns a 2012 chrysler 200. While driving various speeds and depressing the brake pedal suddenly, the vehicle shut off without warning. The vehicle was taken to an independent mechanic, but was not diagnosed or repaired. The manufacturer was not notified of the failure. The failure mileage was 88,000.
Takata recall...i purchased the vehicle 2 months ago at darcars in marlow heights, md and i have already put the car in the shop 4 times for different issues. The biggest issue is after 2 weeks the engine cut off on the beltway(i 95) while heading to the store. Thank the lord that i was able to get on the side lane but i was almost hit by 3 cars, also, 2 weeks after that while driving the engine became very, very loud on the road so i ended up putting it in the shop for 3 days. It is a shame that people/dealers can sell lemons. Please help me with issue to get my money back from the dealer...$12,000 i can be reached at (301)613-8819. Thanks!
Appears to be a common issue in 2012 which chrysler has known about.no heat/ defrost on passenger side apparently caused by engine block manufacturing process fluids mixing with antifreeze causing a blockage in heater core. If they knew, then there should have been a recall, instead of profiting on the repairs needed to correct.
The contact owns a 2012 chrysler 200. While driving 45 mph, the vehicle overheated and stalled and the check engine warning indicator illuminated. The vehicle was towed to an independent mechanic where it was diagnosed that the engine and radiator needed to be replaced. The vehicle was repaired. The manufacturer was made aware of the failure. The failure mileage was 90,000.
Heater and defroster fail on passenger side of vehicle.this causes the driver to not be able to see.the cause of this failure is do to faulty fluid/design by chrysler.this is a major safety issues.
First time car wouldn't start.dealership charged battery and did software update.second time car wouldn't start they replaced battery.third time car wouldn't start battery completely drained they said it was a glove box switch.fourth time car wouldn't start they said it was the usb cable keeping the radio powered on all the time.same chrysler dealership worked on it all four times.brand new car bought august of 2012.all four times have been in less than two months!this car is not safe.chrysler is not doing the right thing by their customers!any help would be appreciated.in the usa we should not have to put up with being ripped off like this.
I was driving my new chrysler 2003.6l approximately 25-30 mph pressed the gas pedal and had no response.engine was dead, the steering locked-up causing the vehicle to pull right running off the road.fortunately, my two children and myself were not harmed.i am extremely disappointed/angry that my children were put into this situation.i believe this is a an unsafe vehicle and investigation should take place.
2 complaints/concerns:1) this affects the 2012 chrysler 200 i purchased used with 62,500 miles. It's been well documented all over the internet and at chrysler dealerships how the 2012 chrysler 200 was part of a group of vehicles with faulty antifreeze from the factory. This antifreeze breaks down and will clog the heater core, radiator, and transmission oil cooler. The recommended repair, from chrysler, is to replace all of these listed parts at a cost of about $2500.00. Chrysler knows about this problem, but refuses to do anything about it. My car is at a chrysler dealership as we speak having these repairs made.2) this one i have not experienced, but i also see a large number of reports where the pentastar v6 equipped in a number of these vehicles will suddenly shut off. Many of these cases are when the cars are in motion. This is a serious safety concern. Issue seems to be centered around a pcm, but there is no recall of any kind on this.
Purchased a used chrysler 200 in february 2017 at 87,xxx mi. It is now june 2017 and 3 times in the last 3 days my car has suddenly died. The first time i was slowing down and made a right turn and upon accelerating it died, dash lights illuminated, quickly tried to restart and was unsuccessful with just nothing happening when turning key. Took key out of ignition and retried and started right up.next day i was again slowing down and making a right turn and bam same thing same details. 3rd incident i was driving straight and the car stalled this time i was doing about 15 mph and the steering locked up, quickly took key out and restarted. Engine light was on and diagnosed as crankshaft position sensor malfunction. Replaced the sensor and have only driven for short distance as the first 2 times this happened were terrifying enough. After hours of online research i've found this is common and just being neglected. Chrysler fix this issue before someone gets seriously injured
My car received a software update for the pcm on 3/2/2017. On 03/6/2017 my car shut off completely in the middle of driving down the interstate.
Heat is not coming out of right side vents, blowing cold air. Took to dealer and they found an issue with the heater core and it needs to be replaced. There's a build up of brown sludge in the cooling system. Car has 68000 miles on it. This will be the second replacement. Last one was replaced at 37,000 miles.
Differential exploded while pulling away from a curb into the road, no traffic, no excess accelaration
The contact owns a 2012 chrysler 200. While stationary, the vehicle stalled without warning. Premiere chrysler in new orleans, louisiana was made aware of the failure and stated that the engine failed. The vehicle was not repaired. The manufacturer was made aware of the failure and stated that the vehicle was out of warranty. The failure mileage was 60,436.
The contact owns a 2012 chrysler 200. While driving 35 mph the steering wheel ceased and the vehicle stalled. The contact was able to restart the vehicle after five minutes. While driving and making a left turn the vehicle stalled again. While attempting to start vehicle there was abnormal ticking noise detected. The abs and traction control warning lights were illuminated. Additionally, the speedometer was inoperable. The local dealer was not contacted. The manufacturer was contacted but no further assistance was provided. The failure mileage was 114,000.
Car continues to have a speed impediment; it hesitates or stalls at 10, 20, 30, and 40 mph increments and also at various times with acceleration from a low speed to a higher speed such as entering a highway from an "on ramp".chrysler tells the owner to continue to just drive it and the computer will adapt to the car. Car stalls, hesitates or maybe experiences a seizure. In shop for more than 4 times with no resolution. Think this needs to be investigated as a safety recall.dealer service man was asked if there was a recall and this question was met with an answer that there have been no recalls.
2012 chrysler 200. When slowing then accelerating in turn about, the 200 will often stall for a second or two, then proceed. Seems to especially happen when attempting to increase speed quickly to enter traffic. The engine will stall and become unresponsive for a second or two before responding again.this has been unsettling a couple of times. This seems to occur when turning and accelerating. I do not have any issues when accelerating in a straight line. The second speed issue is that the 200 is slow to stop revving when accelerating. On several occasions upon acceleration, when i lifted my foot off of the accelerator, the engine kept revving for a couple of seconds and the car kept speeding up. This has not caused any safety issues.
The contact owns a 2012 chrysler 200. While driving 20 mph, there was an abnormal knocking noise emitting from the engine compartment of the vehicle. The vehicle was taken to be diagnosed, but the details of the failure could not be provided. The vehicle was not repaired. The manufacturer was made aware of the failure. The failure mileage was 30,000.
On september 24, 2015, in the morning at 7;30am, heading to work. Heading towards the pa turnpike.my chrysler 2012, hard-top converter car engine shuts down/ stalled without any warning. This is the second time that i have experienced this problem. Last year, it happend in florida as well.i take it to the dealer in florida, and they did not find a cause.in both instances, i have to turn the car off and restart it.i'm concern about this problem because it is a safety concern while driving this car both on the local roads; as well as, the highways.i mostly used the pa turnpike to get to work every mornings.the other complaint i have as well is in the changing of the gear stick (from park to drive, and vice versa).at times, it is seems to be difficult to change gear. This is an automatic transmission drive system so it should not be so hard in changing gears.
Car has 70k miles and heat doesn't work on passenger side of car, windshield defrost does not work, drivers side heat works sparingly.dealership calls for replacing radiator, heater core and oil cooler due to sludge build-up/clogging in coolant/heating system.this appears to be due to an incompatibility between the coolant used by chrysler and the chemicals/oils used in the manufacture of the engine system. This is 100% a manufacturing defect and the dealer & manufacturer are unwilling to replace.doing some research i am seeing this is a fairly common problem with the 2012/2013 chrysler 200, regardless of engine type.this is a safety concern as the windshield can become fogged very quickly while driving under the right conditions (damp weather) and without warning, posing a safety hazard.
"takata recall"when it is cold the defrost won't work and the passenger side of the car is extremely cold.
My car stalled on me about 3 times in august. Twice while driving at a low speed and once while parked. I took it chrysler and they said they didn't find anything. It happened again in september so i brought the vehicle back to chrystal and was once again told they could find nothing. After that while driving on the highway at about 40mph the car started to lose power and traction control, emergency brake and abs light lit up and the speedometer just waved back n forth. It felt like it was stalling and luckilyi was able to pull over. I took it back to chrysler and told them its very dangerous and i can't drive the car like that. They then called me saying they found a loose battery terminal and to see if that helped. No it didn't. While driving on a highway again the car started to lose power and then stopped but did not stall. When i stepped on the gas it mad a noise but did not move. I had to shut it off and restart it. I will going back to chrysler for the fourth time to see if they will fix this dangerous problem.
My chrysler 200 died while driving--still had power, but engine died. The first time,6/8/19, we thought it was a cam sensor-that was the code it threw at the mechanic.we replaced it.then the battery light came on.the battery was good, but the alternator wasn't-so we replaced the alternator.drove it for 2 days & it died again, 6/16/19.took it back & the same cam sensor code is popping up but sensor is still good.got it back, drove it another 2 days & it died again, 6/22/19.towed it back to shop & mechanic cannot duplicate the problem after a week.have it back 1 day & car dies again, 6/29/19.several complaints here mention the car engine dying for no reason, but still have power.we've been lucky-we haven't been on a highway when it's died.each time, we've been driving around the city & making a turn & the traffic flow has been slow.sometimes we've been at a complete stop-others we have not.being that this seems to be a repetitive complaint, why hasn't a recall been issued on the vehicle??
Took car in to dealership years ago to have head rest and airbags fixed. Received a notice by inputting my vin that these fixes were incomplete . Also discovered that the 3.6 pentastar engine from the factory had substandard engine bearings which could result in the engine seizure and the remedy was for the factory to replace the engine. My 2012 chrysler 200 was manufactured during this time frame, yet was never notified by the manufacturer of this dangerous condition.
After owning my car for only a few months the check engine light came on and a minute later the electronic throttle control light and then the electronic stability control light. After taking my car to kendall dodge chrysler jeep ram 5 times, an independent auto shop once and another visit to the dealership where the car was purchased my car is still having issues shifting from 2nd gear to 3rd. At least that's what the auto shop told me the problem is, with the transmission. I hit the gas and the car clunkers and jerks like a manual car when i'm just lightly pressing on the gas. The car doesn't even have 52,000 miles. I've had it less than a year and half the time it's been in and out of repair shops.
My 2012 chrysler 200 s stalled on a major highway. After coming to a complete stop due to traffic the vehicle would not accelerate, the steering locked up and then it shut off. There were no malfunction lights or any other type of warning called chrysler and they said that there are no recalls for this despite there being a number of complaints reported.
Engine stalled forcing me to cross two lanes of traffic almost getting hit by another car engine light came on would not restart if it did start it sputtered the next day i took it to a dealer who told me the following day it's a crank sensor checking online that seems to be a problem with your engines cost me $500 almost to fix the repair and also i had to wait two days without a car and then pay for 2 days for a rental car i do not understand why this was not covered i could have been hurt severely
The chrysler 200 vehicle that i purchased in april 2012 was brought in again on 7/1/13 for service due to front end clanging metal noises which occur while turning, backing up, slowing and stopping. This undiagnosed noise began following several engine stalling episodes, two of which required towing (since i was unable to restart the vehicle to drive in for service).the engine stalling episodes occurred while driving at 55 mph and as stated, twice resulted in towing and service.service on the engine stalling problem occurred in april and again in may 2013. It is unclear why the remedy for the engine stalling was not followed per the nhtsa recall id # 11v487000 (engine and engine cooling) technical service bulletin/chrysler manufacturer remedy- since that recall had already been published.in addition to this safety issue, the front end metal clanging may be the result of towing due to the engine defect and/or a result of another vehicle defect (recall #11v315000 - steering column). This is a vehicle that has multiple problems and poses a serious safety issue due to various problems.it needs to be off the road.
My vehicle just started this week to rough idle when braked at a red light. And when picking up speed in the city or highway it kicks back(rough idle/shaking) alot and the check engine light will flash and then dissappear. Nothing is getting picked up when checking for codes. But i believe it has to do with that safety recall: chrysler town & country engine recall: 11v487000 engine may suffer internal damage and stop running i did get my oil change at the dealership i purchased but nothing came up to them about it as well(since they do inspection). This is my only transportation so i need this to get taken care of as i have 2 kids and appointments. Thank you.
I'm driving the car just shuts off, it seems to be something with the pcm that were to replace. This was very scary and dangerous. This happened in the middle of the intersection traffic flowing and the car stops. It's hard to turn or brake to get out the way of coming traffic.
2012 chrysler 200 convertible heat fails to defrost window causing total visibility loss and inability to see out of windshield.lack of heat does not allow for safe operation of vehicle.this occurs when vehicle is running.the car can not warm up enough to defrost windshield. No heat coming from defrost or vents. Blows cold air. This occurs when driving or stationary. Can not see! dangerous!
I have a 2012 chrysler 200 that stalls randomly. I have taken it in for service and diagnostic services and no results. The system has absolutely no codes stored in the system. It happens randomly while the vehicle is stationary and in motion. I have seen a lot of complaints with the same thing happening to people. It has left me in extremely dangerous situations many times. I do not feel comfortable or safe driving this car. This needs to be investigated as i have learned it has been affecting years from 2011 to 2016
I purchased my 2012 chrysler 200 in 2013. After driving my 200 for a couple years,i notice in the wintertime ,the right side of the windshield was very slow to defrost. Fast forward to 2017 i notice the passenger side was blowing cold air,the driver side was slightly warm.after doing a little research i found that the chrysler has problems with 2012 model heater cores. Chrysler needs to recalled this model year due to the fact there is not enough heat to defrost the windshield.
My car engine is knocking loud when i drive, do i need a new engine..?
Our car started over heating & smoke started coming out, the car was beeping & the gauge for the heat was sky rocketing to the h. White smoke started coming out of the left side of the engine & then the car was making a knocking sound. At the stoplight waiting to turn our car ended up shutting off & not starting.
Heater core...do not purchase this vehicle. Don't take my word for it, research reviews of chrysler's negligence with many makes & models for their ineffective heater core.the cost to fix is not cheap (i can show receipt) very few shops will work on heater core for this car.car has a serious issue with heater core, & i do not want to even give my story as i would just become even more infuriated. Ashame no lawsuits have been successful against chrysler. It's bad enough these idiots designed a vehicle you have to take off entire bumper for to change headlight bump (which cost double the amount of the already expensive bulb).worst purchase ever made, chrysler could give me a car for free & i would refuse to to keep it at this point. Never ever again. Just say no to chrysler
2012 chrysler 200 shut off while driving 45 mph down the hwy with 2 children in the car. I lost power steering and my brakes. Luckily, i made it to the side of the road. It restarted once i turned the key to off first, but shut off on me a second time while idling a few minutes later. I have not driven it since.
As i was driving my car it just stop running, there was no warning lights or nothing came on the car just stop. Then it would not start back up until the next day when it was at the dealership. They check the car out and they could not find anything wrong with the car. This is not the first time this happen and they still can not find out why the car is stopping. Then the lights came on the dash board and i took the car back to the dealer ship and they still could not figure out why they came on because the computer did not report that any lights came on. Then they keep my car over the weekend and they said the car ran fine even though they know the car did stop but since the computer couldn't tell them that there was something wrong with the car there is nothing that they can do. This is a very unsafe car..i wish i know this before i brought this car...
The contact owns a 2012 chrysler 200. While driving approximately 30 mph, the check engine warning indicator illuminated and the vehicle stalled. The contact was able to restart the vehicle. The contact stated that the failure recurred six times. Gossett chrysler dodge jeep ram (1901 covington pike, memphis, tn 38128, (901) 388-8989) was notified of the failure. The vehicle was not diagnosed or repaired. The manufacturer was notified of the failure. The approximate failure mileage was 100,000. The vin was not available.
I bought this car use with 27,000 mile on it. I have only had the car for 45 days or so. My car is jumping forward when i come to a stop. At first the lurching was very faint now at 31,000 miles the lurching is more pronounced.i took the car to the dealership prior to the warranty ending and they acted like they where unaware of the issue/or didn't understand the issue.any way i am beginning to feel unsafe since it is happening more.the car lurched forward during a sudden stop one time, not good.
Drove approximately 0.5 miles when the engine started to kick back, drove another 0.5 miles and as i was parking the car the steering wheel locked up.put the car into park and turned off the engine.the car would no longer start as the engine would rev right up until the engine should flip over but the car just shuts down at that point.waiting for a tow at this point to the nearest dealership.
The contact owns a 2012 chrysler 200. The contact stated that after having his vehicle serviced for nhtsa campaign number: 13v282000 (air bags , electrical system) the check engine light illuminated at 50 mph. The vehicle was taken to a the dealer for inspection and they stated that the evac hose needed to be replaced due to the fact that a rodent had eaten the hose. The vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was 33,122. Updated 02/11/14*ljthe consumer stated there was a problem with the fuel tank evaporate hose.
Takata recallno heat on passenger side, blows cold air. Unable to defrost passenger side of windshield. Chrysler service advised that heatercore plugged, need to replace heater core, radiator, engine oil cooler & thermostat.had all replaced, at a cost of $2200. One year later, same problem, no heat passenger side.
I purchased a new 2012 chrysler 200.in dec-2015 at 46,000 miles the heater quit working correctly.the dealership said the heater core was clogged and needed to be replaced for about $1200.even though the car was passed its 36,000 mile warranty chrysler paid for the repair.i believe because they knew they had sold a bad product.3 years later (dec-2018) at 76,000 miles the same problem occurred.the dealership is now saying the whole coolant system (heater core, radiator, hoses, thermostats and engine flush) needs to be replaced at a cost of $3600.maintenance schedule says coolant good for 5 years and 100,000 miles.first failure at 3 years and 46,000 miles.second failure at 3 years and 30,000 miles.chrysler refuses to accept responsibility or help with repairs.
Engine shuts off while driving down the road. It happens on the freeway, on city streets, or at idle. We had the pcm updated in december 2016. It is now march 2017 and the vehicle continues to shut down while driving or at idle. It is extremely dangerous. The brakes barely work and you lose power steering when this happens. This is a serious issue and needs to be addressed. There are hundreds if not thousands of posts online about this issue, with no resolution. This needs to be addressed before someone dies.
The car has stalled on four different occasions while driving.it stalled three time while driving in traffic. One time it stalled on the highway. The car has turned back on after a couple of tries. A malfunction indicator light comes on after the incident and stays on for a period of time. The light simple goes out without any intervention. Everything appears to be running okay and then another incident of stalling occurs.
While driving my vehicle back the office from my lunch break, i made a right hand turn onto the main road and began to accelerate the vehicle with more gas.at about 35mph the car engine completely shut off and i had to coast to the side of the road with no power steering.i had to wait approximately 20 mins until my car would restart again.i was able to get back on the road until after another few hundred yards of driving the car stalled again completely.i was then forced to call a tow truck to have it taken to an auto shop.
The contact owns a 2012 chrysler 200. While driving 25 mph, the contact noticed the temperature gauge rising. The contact continued to drive at a lower speed until she arrived home. The vehicle was taken to darcars chrysler dodge jeep ram of new carrollton (located at 8100 annapolis rd, new carrollton, md 20784, (301) 459-6800), but they were not able to duplicate the failure. The vehicle was not repaired and the failure continued. The manufacturer was not notified of the failure. The failure mileage was 41,788.
While driving i started to coast to takesharp turn and engine died, no power steering and no brakes.couldn't turn and ran off the side of the road.this is a major issue.
The contact owns a 2012 chrysler 200. The contact stated that while parked, the heating system was not emitting hot air. The vehicle was taken to the dealer where it was diagnosed that theradiator and heater core needed to be replaced. In addition, the cooling system needed to be flushed. The vehicle was not repaired and the failure recurred. The manufacturer was not made aware of the failure. The failure mileage was 60,000.
The contact owns a 2012 chrysler 200. The contact stated that while making a left turn at an unkown speed, the engine stalled and the steering wheel seized. The vehicle was taken to the dealer but the failure could not be determined. The failure mileage was 5,887 and the current mileage was 8,495.
On april 26, 2012, i purchased a brand new 2012 chrysler from an official chrysler corporation dealership.since then this car has been put in the shop approximately 30 times for from medium to major problems. The 1st major problem was 9/26/212 which was diagnosed as gear-rack and pinon.it has had two lifters(relative to the motor) because of loud tapping.three heater cords; a couple of re-calls;transmissions leaks; internal engine damages; headlamps needed immediate replacements; washer fluid tank leaked and needed immediate replacement; the car horn failed to blow on demand; brakes needed immediate replacements; camshaft, rockers had to be replaced twice; heater cord experienced internal failure and had tobe replaced; brake pads; brake light (dashboard) has been beeping on since 2013 and is still doing the same thing today; engine air filter had to be replaced; and a host of other vehicle problems that should not be happening on a brand spanking new 2012 vehicle!!please assist and advise.
While driving, the car began to rapidly lose functionality while warning lights were appearing on the dashboard until it abruptly shut down while driving in traffic. The time from no warning lights to complete loss of functionality was approximately 10-15 seconds. The shut down included an abrupt loss of power steering and braking capabilities while driving on a busy street at night. I was able to quickly compensate for the loss of power steering and braking and stop the vehicle while avoiding a crash, but just barely. Thankfully, i broke down next to two police officers who helped push my vehicle onto the side of the road. These officers may be able to attest to the fact that no noises or abnormal operation of the vehicle was apparent before the abrupt shut-off while driving. Attempts to restart the vehicle involved no clicking or the engine attempting to turn over. The vehicle is currently being repaired, but the preliminary diagnosis is one of a faulty alternator. I will attempt to retain the faulty alternator from the repair center. I had only started the car 2-3 minutes before the incident and there were no apparent electrical issues (engine struggling to start, lights dimming, etc.) while starting the car or during operation.
I have talked to several people with chrysler 200 and the all have faulty heater core
I left my home, in my vehicle which had been running completely normally with no dash lights on, overheating, leaking, etc. I live on a dangerous road (it's extremely curvy, dark, has a high accident rate and no shoulders just 12ft. Deep concrete ditches on both sides. I left home around 9:35pm and made it approx. .5-1 mile and braked slightly to take a sharp curve, and with no warning my engine stalls completely (also causing loss of power steering). I was doing roughly 25-30 mph. When the engine died. The loss of power steering caused me to be unable to keep my vehicle safely in my lane on this sharp turn (i was just lucky that the oncoming lane was clear). Luck is also all that prevented me from breaking down awkwardly positioned right in a dark blind curve. I was able to coast on what little speed i had left, to one of the only safe pull offs on my road ( i barely had enough momentum to do that, and it was just by chance that i was by the spot where it was possible to get out of the roadway. I have seen well over 50 online complaints so far, of owners of 2012 chrysler 200's who have suffered failures practically identical to mine. My vehicle had been in for regular maintenance/oil change just a week or so prior to this, the inspection revealed no issues needing attention. The car runs perfectly normal right up to the moment you loose all power and your ability to steer with any precision or speed. This problem is obviously fairly common in this vehicle, seriously impairs your ability to control the car suddenly and without warning, causes no check engine warning therefore no error code to diagnose by, and depending on your circumstances and luck at the time could eithercause a giant inconvenience or a serious tragedy. Chrysler already recalled for a nearly identical issue but only included the 2015 models. They need to address this before someone dies.
The contact owns a 2012 chrysler 200. The contact stated that after driving approximately 30 mins and parking the vehicle, a loud banging noise, steam and smoke was present coming from under the hood. The vehicle was towed to an independent mechanic who determined that the plastic radiator hose connector had failed and needed to be replaced. The vehicle was repaired. The manufacturer was notified of the failure. The failure mileage was 100,000.
I own a 2012 chrysler 200, the engine stops/fails about every two months while braking or while stopped. This is dangerous as it can stop anywhere and they might rear end the car or something. I have taken my car to the chrysler dealership 4 different times with the same issue, the first time they changed the pcm. After about 2 months the car's engine stopped while braking or while at a stoplight. The 2nd and 3rd time i took the car they did not find anything wrong with the car and gave it to me after a couple of days. The 4th time when i took the car they said that it was the battery and they put in a new battery. Well about 2 days ago the car stopped again while at a stoplight. I have not taken the car to the dealership as they never find anything wrong with the vehicle. I am tired of them not finding what is wrong with the car. I believe that i speak for many chrysler 200 owners when i say that an investigation needs to be done for the whole chrysler group, especially to the 200, which have many complaints online and none one seems to find the solution. Please investigate this for the safety of the drivers. I am so sick and tired of the mopar mechanics not finding anything. I do not know if the issue is with the pcm, computer, or engine. Please investigate.
The contact owns a 2012 chrysler 200. While driving 50 mph, the vehicle stalled without warning. The contact mentioned that the vehicle would operate normally after it was shut off and restarted. The vehicle was not taken to a dealer or independent mechanic for diagnostic testing or repairs. The manufacturer was not made aware of the failure. The failure mileage was 80,000.
I only have heat on the drivers side of the car. We just hit our 100,000 bumper to bumper warranty. Had the car in the shop twice with coolant smells. Mechanics never found a problem. Everywhere i read there are tons of complaints about this issue. This is a $1000.00 repair! a flush is $150-170. We have already done this.i'm ready to trade it in but i do love my car. Not sure about how i feel about chrysler knowing about a issue and not offering assistance with the repair. Maybe they better send out a massive rebate to old owners in hopes of them staying a customer.
The contact owns a 2012 chrysler 200. The contact stated while driving 60 mph, the vehicle stalled without warning. The contact parked on the side of the road for 30 minutes, restarted the vehicle and drove to his destination. The vehicle was taken to the local dealer gwinnett chrysler dodge jeep ram (5054 ga-78, stone mountain, ga 30087, (404) 492-6831) however, the mechanic was unable to duplicate the failure. The contact stated that the failure recurred five times. The vehicle was not repaired. The manufacturer was informed of the failure. The failure mileage was approximately 120,000.*dt
When going into a stop or a slow down, the engine stalls; this is now the 3rd time chrsyler is looking into it.car is a 2012 chrysler convertible spurchased in febof 2012 w/ 100 miles.1st. Happened at ~5k2nd happened at ~7k in july 18,20123rdhappened at ~12k oct 8th, 2012this last time the car died on my 4 times in 5 minutes.dealer was able to reproduce the error.they are saying it is caused by a asd(v) circuit in which the relay is broken.1st time they reprogrammed the computer.2nd time they replaced the part containing the relay.3rd it is the relay again.it is a major safety concern as i almost got rear ended by a van this time as i was making a legal u-turn.
Was at a stop light and after taking off the car shut completely down with no warning no engine light indicator until after this happened. I tried to start it and it cranked but didn't start all the way, i had it towed home andnow it starts. I had a six month old infant in the car with me when this happened and i don't feel safe when the car can just shut down like that. I feel there is a default in the engine, we purchase this car a year ago. Thank god there was no one behind me when this happened.i also have had problems with the brakes from when we purchased the car i brought the car to the dealer four times before someone figured it out. It was fine for four weeks and the noise is back, there is a noise in the brakes only when you press the brakes lightly. This problem has not been resolved. And the the warranty is up. I feel it's a defect. Upon my last visit to chrysler there was a customer there who also has a 200 with the same brake problem they were trying to resolve.
Car is a 2012 model, purchased three days ago with only 10 miles on it.today it stalled as it was idling at red light.it stalled as i was making a right hand turn.it stalled as i was turning left into my garage to park. I called my salesman, he claims he knows nothing about it and referred me to the manager.he also claims he has never heard of why this would happen.yet i find out from a friend to search the internet.i do a search and see many articles from today and over the weekend on this.so, how does a dealer not know about this before selling me the car? concerned about my kids being in the car with me.
The contact owns a 2012 chrysler 200. The contact stated while driving 35 mph, the vehicle was pulling to left with the temperature gauge rising rapidly. The contact stated the engine overheat warning light was illuminated. The vehicle was driven to the residence. The vehicle was not diagnosed nor repaired. A dealer was not contacted. Upon investigation, the contact associated the failure with nhtsa campaign number: 11v487000 (engine and engine cooling) however, the vin was not included. The manufacturer had not been informed of failure. The failure mileage was approximately 148,000.*dt
The contact owns a 2012 chrysler 200. The contact stated that when driving between 16-22 mph, the vehicle would hesitate. The vehicle was taken to the dealer for inspection where they stated that the vehicle was changing gears as it was designed. The vehicle was not repaired. The contact also stated that the steering wheel seized without warning. The manufacturer was notified and stated that there were no recalls on the vehicle. The failure mileage was 2,000. The consumer stated the very day they picked the vehicle up, it stalled in the entrance way. The dealer claimed, the vehicle ran out of gas. As her son drove the vehicle home, he noticed when coasting at low speeds, the vehicle would kick back. The mechanic stated the jerk/kick was from the engine shifting gears. The kicking would go away, when the accelerator pedal was pressed.when her son turned the steering wheel to the right and then straightened it out, by turning the wheel to the left, the steering wheel locked up.he put the vehicle in park and shut off the engine. He tried to re-start the vehicle several times, but the engine would rev up tight until it was about to start, but would immediately shut off.the vehicle was towed to the dealer, where they found a code, but it had nothing to with the problem, that was being experienced. Updated 01/16/13
The passengerside stopped working no heat. Took the car to dealership and they flushed the system with chemicaland coolant a lot of junk came out. That didn't work now dealership says heater core and radiator needs replaced $1700. I research this and there has been a problem with 2012 with the same problem. There should be a recall.
The contact owns a 2012 chrysler 200. The contact stated while driving at 50 mph, the vehicle stalled. The contact stated that the check engine warning light was illuminated. The vehicle was taken to a local dealer where the vehicle was serviced under nhtsa campaign number: 13v282000 (electrical system, air bags), 16v668000 (seat belts, air bags), and 17v640000 (seats, air bags). The vehicle was repaired however, the failure still occurred. The contact was relating the failure to nhtsa campaign number: 11v487000 (engine and engine cooling). The manufacturer had not been informed of the failure. The failure mileage was approximately 181,000.
The contact owns a 2012 chrysler 200. The contact stated that while driving 20 mph, the steering wheel became difficult to turn. The vehicle was taken to the dealer for inspection where they stated that there was no power steering fluid in the vehicle. The vehicle was replenished with power steering fluid but the failure recurred. The also contact stated that the power steering hose exploded and needed to be replaced. The vehicle was repaired. The manufacturer was not notified. The failure mileage was 6,047. The consumer stated there were numerous problems with the vehicle, such as a coolant leak, oil leak, air condition, the cd player did not work, the power steering hose burst, the wire harness, the transmission was replaced, the engine was noisy and the seat belt on the passenger side was not properly installed.the vehicle cut off several times. Updated 10/31/13
Passenger side air blowing cold air while in high heatgoogled it seems to be major issue in these vehicles chrysler knows about it says it's a chemical the addto coolant plugging heater core.
I was driving down a busy street, trying to make a left hand turn through traffic, and my car stalled without no warning and everything was locked including brakes. I took it into chrysler and they couldn't find anything wrong with it because no fault light was coming on. So they took the next step of putting a module on my car for 2 days to see if it happens again, but lucky for me it didn't because the first time was scary enough for me. Then when i took it back in they just told me that when my car does that just put it in neutral and restart it. So three weeks later my car did it again but this time i was on a busy freeway going 70 mph, so i tried their suggestion and it did not work, for the second time everything just quit working in my car. So i called them again talked to the manager at chrysler and he said if there is no lights coming on when my car does this he really can't do anything about it.
The chrysler 200 vehicle that i purchased in april 2012 was brought in again on 7/1/13 for service due to front end clanging metal noises which occur while turning, backing up, slowing and stopping. This undiagnosed noise began following several engine stalling episodes, two of which required towing (since i was unable to restart the vehicle to drive in for service).the engine stalling episodes occurred while driving at 55 mph and as stated, twice resulted in towing and service.service on the engine stalling problem occurred in april and again in may 2013. It is unclear why the remedy for the engine stalling was not followed per the nhtsa recall id # 11v487000 (engine and engine cooling) technical service bulletin/chrysler manufacturer remedy- since that recall had already been published.in addition to this safety issue, the front end metal clanging may be the result of towing due to the engine defect and/or a result of another vehicle defect (recall #11v315000 - steering column). This is a vehicle that has multiple problems and poses a serious safety issue due to various problems.it needs to be off the road.
There is low heat output from the heater vents due to the heater core plugging up with "sludge" as chrysler calls it. There is a chrysler star technical assistance hotline case, number [xxx] explaining heater core restriction due to sludge causing poor heater system performance. It is a well known problem with a large number of chrysler 200 which i am sure can be verified by chrysler. I believe it should be a recall, or at least an extended warranty issue. The star case states to replace the heater core, radiator, radiator cap and reverse flush the entire system if the customer complaint can be verified by the technician, however it does not explain the actual cause of the sludge.here are other weblinks related to the same issue that is in my opinion an obvious problem that chrylser should place a recall on immediately.http://starparts.chrysler.com/newsletters/newsletter_oct_2012.pdfhttp://www.200forums.com/forum/10-chrysler-200-engine-technical-discussion/1966-fyi-heater-core-6.htmlhttp://www-odi.nhtsa.dot.gov/owners/searchresults;jsessionid=cnhmjlwqht8gkgyhdrzyjpxxpx2lnz4jbzs8mt3qb6tmzctns2rp!389628101?prodtype=v&searchtype=prod&targetcategory=a&searchcriteria.model=200&stats=1306768%2c2%2c0%2c135%2c0%2c200&makestats=1306768%2c2%2c0%2c135%2c0%2c200%3b1369770%2c4%2c0%2c62%2c8%2c300%3b1883971%2c1%2c0%2c0%2c0%2csebring%3b1306769%2c4%2c1%2c149%2c3%2ctown+and+country%3b&jsonbaseurl=%2fdownloads%2ffolders%2f&searchcriteria.model_yr=2012&searchcriteria.make=chrysler&searchcriteria.prod_ids=1306768.information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6).
Purchased vehicle on nov.1st.2013.noticed when turning off vehicle there is a loud clicking sound on front right of vehicle.had it checked by a mechanic and was informed that there was a sensor malfunction near the timing cover.went to dealership and was told that this was normal for this model and make of vehicle.someone is wrong,either the mechanic or the dealership.who?
When going over the bridge or entering into traffic car seem to stall, radio and light shutoff and give me a error message enter id code. Have been nearly rear ended by on coming traffic.the console for the heat controls have fell down and dealersays they cannot find anything wrong with it.purchased the car in march of 2012 and have had problems since i bought it. I love car but hate all the problems that i am having and it's only been 9 months and took it back to dealer about 4 times already and have an appointment on 1/11/2013.
The first incident with my brand new 2012 chrysler 200 was failure to start. I went to start my car and turned the key but the car would not start the engine stalled. I started to turn the key again , again did not turn on. After the third time it began. I brought it to the dealer they said they could not duplicate my problem, contacted chrysler to see if there was any report of thisbut they hadn't had any complaints. The dealer then sent me on my way. On april 1st i was driving my 2012 chrysler 200,658 miles,with my two year old daughter in the car. As i was turning right off of a main streetinto a the parking lot there was another car moving soat the entrance, i pressed my brakes shortly and put the car in reverse i was not in the other vehicles way so i then proceeded to put the car back in drive but the car would not move. At thistime the car was at a complete stop and in the fast moving traffic with my daughters end out in the main street.ihave brought my car to the dealer which they have told me they are unable to duplicate the problem and thatthey spoke with chrysler and asked for reports but chrysler said no problems such as mine has been reported. The dealership or chrysler is helping me in this matter i don't feel safe and i have expressed this to them. I and my daughter are at risk with this vehicle. I feel something is wrong and since the car is not leaving and sensors on after either incidenti feel it is not safe to drive. If the car stops on the interstate and stalls or fails to drive my daughter and or i can be killed.
2012 chrysler 200 heater issue.vehicle will not warm on passenger side preventing defogger to reduce ice or snow from windshield.the vehicle was taken to chrysler dealership and after several attempts to remove sludge from the radiator and heater core the heater still will not maintain heat to the passenger side which is a safety issue in keeping the windshield clear of ice or snow. Dealership indicated that heater core, radiator and coolant reservoir will all need to be replaced.in reading various forms its known that chrysler uses some type of chemical to plug any pin holes in the radiator and this product is causing a sludge in the system and creating the problem.chrysler will not or indicated after calling, they will not pay the $1700 cost of the repairs that were created during manufacturing.
The right side (passenger side) of vehicle gets very little heat. This caused the entire car to be cold. The defrost does not melt ice on windshield.this first happened when the car was 11 month old.the dealer replaced the radiator, heater core and cleaned the block.he said these were full of sludge. Today, march 2015)at 34017 miles, i picked up the car from the dealer after complaining of the same lack of heat and the same was reported,replaced radiator,heater core, oil filter cooler and flush cooling system.also stated on the repair invoice "performed test and repair per star case [xxx]".this is apparently an account to charge the repair back to chrylser.chrysler knows of this problem.the service advisor told me that someone at manufacturing plant added a sealant to stop leaks.he said it is well known not to use this sealant because of the problems it will eventually cause in the system.this has been repaired twice, i have no reason to believe that it will not happen again.it has been paid by warranty but some day it will be out of warranty and i will not be the one paying for it!!!!chrysler must be held accountable for this and make a permanent correction to this problem.information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6).
The contact owns a 2012 chrysler 200. The contact stated that the heater did not work on the passenger side of the vehicle. There were no warning indicators illuminated. The vehicle was taken to haasz automall of ravenna (4886 oh-59, ravenna, oh 44266) where it was diagnosed that the heater core and the radiator needed to be replaced. The contact was informed to pay a deductible because the vehicle was not purchased at the dealer. The technician also stated that the vehicle was out of warranty. The manufacture was made aware of the failure and stated that the deductible needed to be paid. The vehicle was not repaired. The failure mileage was approximately 54,500.
The contact owns a 2012 chrysler 200. The contact stated that the air conditioning unit did not emit hot air on the passenger side. As a result, the vehicle would not defrost. The vehicle was not diagnosed or repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 10,000.
The contact owns a 2012 chrysler 200. The contact stated that while driving 20 mph, the steering wheel became difficult to turn. The vehicle was taken to the dealer for inspection where they stated that there was no power steering fluid in the vehicle. The vehicle was replenished with power steering fluid but the failure recurred. The also contact stated that the power steering hose exploded and needed to be replaced. The vehicle was repaired. The manufacturer was not notified. The failure mileage was 6,047. The consumer stated there were numerous problems with the vehicle, such as a coolant leak, oil leak, air condition, the cd player did not work, the power steering hose burst, the wire harness, the transmission was replaced, the engine was noisy and the seat belt on the passenger side was not properly installed.the vehicle cut off several times. Updated 10/31/13
The contact owns a 2012 chrysler 200. The contact stated that while driving 20 mph, the steering wheel became difficult to turn. The vehicle was taken to the dealer for inspection where they stated that there was no power steering fluid in the vehicle. The vehicle was replenished with power steering fluid but the failure recurred. The also contact stated that the power steering hose exploded and needed to be replaced. The vehicle was repaired. The manufacturer was not notified. The failure mileage was 6,047. The consumer stated there were numerous problems with the vehicle, such as a coolant leak, oil leak, air condition, the cd player did not work, the power steering hose burst, the wire harness, the transmission was replaced, the engine was noisy and the seat belt on the passenger side was not properly installed.the vehicle cut off several times. Updated 10/31/13
Since new, this vehicle has poor low beam headlights, that seem to be directed downward, making night driving over 50 mph hazardous. At times, i must rely on the headlights of other cars to see the road ahead. After owning this car one year, i can't accept this any longer. The dealer at first said they could not be adjusted, but is now willing to check them at a future appointment. I found adjustments above each headlight, engraved "up and down." a special tool is needed to perform this adjustment. I feel that chrysler needs to be made aware of this problem in their vehicles. I have reported it to their customer service as case # [xxx]. I have owned over twenty cars and this is the only one with poor low beams.information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6).
I own a 2012 chrysler 200, i love my car; however, the head lights are pointing towards the ground making it almost impossible to see anything in front of me while driving. I've changed replaced the headlight bulbs as well as cleaned the headlamp. Unknown 2.during the winter months my car makes the grinding noise when starting up.
The contact owns a 2012 chrysler 200. The contact stated that the headlights only illuminated the road partially, as if there was a shade over the light. The contact activated the high beams in order for the full light to illuminate the roadway. The failure recurred numerous times. The vehicle was taken to a dealer for diagnosis but the contact was informed that the lights were operating as designed. The manufacturer was notified of the failure. The vehicle was not repaired. The failure mileage was 1,800 and the current mileage was 4,500.
The contact owns a 2012 chrysler 200. While driving at night, the headlights illuminated very dimly and the driver was unable to see the road ahead. The failure occurred while using both the high beam and low beam headlights. The cause of the failure was not diagnosed and the vehicle was not repaired. The vin was not available. The failure mileage was 62,000.
The contact owns a 2012 chrysler 200. The contact stated that while driving various speeds, the low beam headlights were activated and failed to sufficiently illuminate the road at a distance of thirty feet and over. The vehicle was taken to an authorized dealer three times and they were unable to locate the problem. The manufacturer was notified of the issue. The approximate failure mileage 2,000. Updated 6/10/14
I have a 2012 chrysler 200 touring v6 bought it brand new. While driving on the highway taking the off ramp i engage my brakes before i get to the traffic light also engaging my turn signal. As soon as the turn signal is engaged all my lights flicker off and on this included the dash lights, stereo and the center console everything except my headlight flicker. On a few occasions the lights have totally went off and would only come back on when the turn signal was disengaged. I had taken the vehicle to a mechanic who tested my battery and alternator also checking all the fuses. He was at a lose to explain why the [xxx] was doing this. I also contact the dealer who sold me the vehicle and gave me the run around stating that they had not heard of any other vehicles doing this and dismissed my worries with saying its is your battery and or alternator.information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6).
The contact owns a 2012 chrysler 200. The contact stated that while driving at night the headlights illuminated downward and did not provide sufficient illumination. The manufacturer was made aware of the failure. The vehicle was taken to the dealer for diagnosis. The technician stated there was no repair because the headlight assembly was operating as designed. The vin was not available. The approximate failure mileage was 13,000.
I feel i am driving my future casket.while driving at night in rural areas with no artificial lighting i have very limited view with headlights on low beam. The design of headlight is causing this i feel.there is a flipper lid that raises and lowers with low beam and high beam. The lid design is cutting the high of beam off and while driving there is a definite black out vertically.so low that one cannot see much higher than the hood of the car.high beam eliminates this problem as the flipper lid is raised out of view.the bulb is so far set back in a tube that any horizontal or side view is diminished greatly. Cannot watch for deer.going around curves the view is almost none existent.i have slammed on my brakes and slidseveral times due to this and i am a very cautious slower driver. The road signs are cut off from this blackout line as when you can get within reading distance then the signage disappears and all you are left with is a view of bottom of pole. Great/so your only option is to drive with high beam all the time and this is against the law.on carcomplaints.com there are many complaints about the issue concerning safety due to poor headlight design with chrysler 200 2011.i asked about this issue at the dealer concerning bulletins on this safety issue. They said none.i have literally been stuck with a unsafe new vehicle and getting many adjustments upward that have not had any safe results. I have on more tomorrow. I love all the other features of this car.please help the other customers by making chrysler have a safety recall. To replace these headlights immediately.i do no want to have a crash, fire, injury, or fatality.i do.
Head lamp projection on the 2012 chrysler 200 is very limited on low beam (50 feet) which is unsafe and is going to cause death or injury. This is a design defect and cannot be corrected by the dealer for which 2 attempts were made. In addition, the manufacturer was contacted for correction. They stated the head lamps operate as intended and there is nothing to be done. Either the vehicle must be driven very slowly so that the driver can react to the limited projection field or high beams must be used which blinds the oncoming traffic and is illegal in most conditions. There is a lid which covers the bulb half way on low beam and retracts fully on high beam. The lid restricts adequate projection and also restricts beam projection to the sides. This is an extremely unsafe vehicle in this condition for night time driving and should recalled for correction. The dealer has had numerous complaints on this model, but says there is nothing they can do since the manufacturer will not acknowledge aproblem. I have read numerous other complaints in your data base concerning the same problem and have spoken to other owners who acknowledge the problem. Not driving the car at night or driving with high beams on is not the answer. Please get the manufacturer to acknowledge and fix the design defect immediately.
The headlight illumination of the 2012 c/200 is driving blind at night and dangerous.there is an extremely limited field of vision and feels like driving with curtain over the lights.the light aims real low and the bulb is too small.using high beam is not much better.several times i came very close to hitting another car and person. I feel like i am driving blind and have confined myself to not driving at night.there has to be a remedy for this problem.
The contact owns a 2012 chrysler 200 touring. The contact stated that whenever driving at various speeds at night the headlights would not illuminate the entire road and distorted the visibility of the roadway. The vehicle was taken to an authorized dealer twice for the problem. The headlights were readjusted however, the failure continued. The technician informed the contact that there was a problem with the brightness of the headlights. The manufacturer informed that the defect was a characteristic of the headlight. The approximate failure mileage was 200.
Low beam headlights are ineffective, cast a beam only about 100 feet on dark roads with restrictive side vision. The beam is even more ineffective when driving downhill and the light beam is only about 50 feet.the dealer explained that it is a one bulb system with a shutter that covers the bulb half way when changing from high to low beams.chrysler is offering no resolution to the problem which has existed since its 2011 model.this system causes the operator to continually use high beams to properly illuminate the roadway even at low speeds of 25-35mph on rural roadways.there should be a recall or retrofit of the headlight assembly to a two bulb or two element bulb system.
The contact owns a 2012 chrysler 200. While driving approximately 60 mph, the vehicle lost power, but did not stall. Additionally, the tail lights and driver's side headlight were inoperable. The vehicle was taken to deacon's chrysler dodge jeep ram (located at 835 som center rd, mayfield, oh 44143, (440)442-0424) where it was diagnosed that the totally integrated power module needed to be replaced. The vehicle was not repaired. The manufacturer was notified. The approximate failure mileage was 75,899.
Driving and interior lights dim down and get real bright spontaneously. Also my seat belt light and chime don't work all the time?? trans already slips when leaving town at a medium acceleration? only 75000 miles on the car.
Projector type head lamps are aimed too low and cannot be adjusted as designed.on dark roads peripheral lighting from head lamps is non existent. Brights are needed but not practical for constant use and is illegal in town as well.this is a real design flaw and some one is goingto get hurt in a night time accident due to the poor design of the lighting system on this model.
On 1/12/2020 while driving home from work i turned on my right turn signal to merge and it rapidly clicked and flashed on the dash after the initial 3 normal flashes and i noticed the car in the lane next to me wasn't acknowledging my turn signal. Once home an hour later, i realized my passenger rear tail light was steadily light (not flashing) even though my car was off and my lights were not engaged and position off. I could not get my turn signal/tail light to turn off. The brake lights work fine when the brake is applied but the tail lights will not turn off. The rear signal won't work either since the light won't turn off to flash. I had to remove the light from the rear fender and unplug the light so my car won't die and plug it back in when i go to drive so i atleast have the tail and brake light on while driving. I can find no info on how to fix this and chrysler wasn't any help. The problem is still unresolved, but it did go off for just one moment, flickered and came back on when i plugged it back in the last time i drove.
This model has a substantial headlight projection issue.the headlights (low beam) do not project far enough to allow the driver to maintain posted speed limits.in areas where there is no street lighting or when driving in rural or unfamiliar areas this is extremely dangerous and you find you have to slow down to a crawl or use high beams - both an issue when other cars are present.i have had other people drive my car to verify and the first thing they say is that it's dangerous and they would not drive this car at night and they were very uncomfortable with the way the headlights projected to the point they thought the lights were not fully on. Have seen this issue from other owner blog entries.
The contact owns a 2012 chrysler 200. While driving 45 mph, the front passenger side headlight and the driver side tail light failed to illuminate. The vehicle was taken to a dealer where it was diagnosed that the tipm failed and needed to be replaced. The vehicle was not repaired. The manufacturer was not notified of the failure. The approximate failure mileage was 80,000.
Takata recallunknown my car stalled out on the side of the road and i left it there to be picked up by my mechanic the next morning. I found out the next day that my car had been crashed and i went to the tow yard where the vehicle had been taken to retrieve my personal items from the vehicle and noticed that my airbags did not deploy. My car has been considered a total loss by geico car insurance. Geico claim number [xxx]. I still have my title, it is a rebuilt one. Geico has been taking their sweet time to reimburse me for my vehicle. The actual accident occurred on april 25th, 2017. The police report is inaccurate. Today is august 30th, 2017 and i'm still waiting on a check. The tow yard has apparently become the lienholder so i've been told and geico has to pay them off before they can pay me? i don't know it's crazy. There would be no lien if geico had handled this in a timely manner. I have had to come out of pocket to purchase a cheap car in the meantime while i wait. I have just recently received emails from carfax saying that my car may be at risk of being recalled so i put in my vin number ([xxx]) and it says that my chrysler 200 2012 is a s61. However, i was aware the passenger seatbelts were locked but i was still able to wrap the driver's belt around me. Furthermore, i've had numerous headlight issues in both headlights and the ac eventually stopped working. There was also a check engine light on that could not be turned off. I spoke with chrysler and they told me nothing can be done as far as reimbursement at this point because i have no possession of the vehicle. However, the title is still in my name and the possession issue is geico's fault. I am looking for some type of justice in this situation it could have been me in the crash. I am [xxx]and it says under federal law that my vehicle can be replaced. #16v-668information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6).
The contact owns a 2012 chrysler 200. The contact stated that while driving approximately 35 mph, he noticed the headlights did not illuminate properly. The contact also stated that he had to utilize the high beam headlights in order to view the roadway when driving at night. The vehicle was not taken to the dealer for diagnostic testing. The manufacturer was made aware of the failure and advised that the vehicle was not included in any recalls. The vehicle was not repaired. The approximate failure mileage was 1,000 and the current mileage was 3,000.
The very first time i used my headlights for night driving i was totally amazed at the fact that you have very little field of vision.there is almost a curtain like affect and depending on the road you are traveling there is sometimes as little as 20 feet of vision.it is all but impossible to drive at night safely with this vehicle.if you live on back roads (as i do) it is not safe to drive at night.this car is just days old and i can only drive it during the day.taking it back to the dealer has not proven to be effective.the comment that i get is that its just the way the car was manufactured and that's how the lights will work.these cars are a hazard and something needs to be done immediately before someone is killed because they can't see when driving at night.i will never buy another chrysler product and i will tell everyone that will listen about my concerns.
The dashboard lights and the head and back lights will flicker on and off.the car has shut off while driviing in traffic.sometimes it doesnt start at all , i have to baqng the door and then the loghtas will come on.i put a brand new battery and altintor in the car and my nechnanic doesnt have a clue what is wrong woth it.believe it to be the computer system.
The contact owns a 2012 chrysler 200. The contact stated that while driving at approximately 5 mph, the passengers side headlight became inoperable. The vehicle was taken to a dealer where it was diagnosed that the headlight module failed and needed to be replaced. The contact was informed that the led light bulb was not replaceable by itself. The vehicle was not repaired. The manufacturer was not made aware of the failure. The failure mileage was 38,000. The vin was not available.
It has been increasingly difficult to see at night when driving my chrysler 200 2012 in low lit areas due to the headlight beams.less light? aimed low?i have to drive far slower than posted around bends at night. I don't recall this issue when i bought the car brand new.i have had it one year and have just over 10,000 miles.i don't usually have to drive at night other than my well lit neighborhood ,so this could have easily gone unnoticed.either way, this terrifies me.the other issue i have is a jerk when shifting to reverse or drive. It is a loud clunk and i feel the vibration. I will not drive at night in low light areas until resolved.i also feel the car pulls to the right when driving. I will contact the dealer soon, until then i just don't feel safe driving while on dark roads.
The contact owns a 2012 chrysler 200. The contact stated that the headlights would not illuminate from the side when driving at night.the failure would affect the contact's visibility of the roadway when attempting a turn.the contact took the vehicle to the dealer but the vehicle was not repaired. The failure mileage was unknown. The current mileage was 3,000.updated 01/30/13*lj updated 1/31/2013
The contact owns a 2012 chrysler 200. The contact stated that the headlights would not illuminate far enough when driving at night. The lights would not illuminate any farther that 20-25 feet in ahead. The dealer was notified who adjusted the lights and advised the contact that the failure was a design flaw with the lightning and nothing else could be done to correct it. The manufacturer was not notified of the issue. The failure mileage was unknown. The vin was unknown.
Extremely poor illumination from headlights, especially low-beam! the projector lights have a 'shutter' that covers a portion of the beam to create low-beam. This causes a distinct, visible horizontal black-out line across the illumination and leaves little to no illumination on the roadway especially on rural roads beyond city lighting! when car goes down-grade, this blackout line dips to cover the roadway completely in front of the car causing total darkness momentarily. This and no corner lighting is very dangerous and will eventually at some point cost a life! there also is no side or corner illumination in low-beam nor in high-beam. One mechanic told me the bulb is set too far back in the projection tube blocking the side illumination and it is not adjustable. Dealer has checked this condition and problem is not fixed. It appears to be a design problem (a serious one) and the internet is full of complaints from chrysler 200 owners about this. Chrysler needs to recall these cars and refit the headlight units with a safe, operational design!
Cant see at night with the low beams. Needs to be replaced with a two bulb system. Does some one have to die before this issue is addressed?
My complaint about this vehicle is the headlights. They are aimed to low, do not project out far enough and the low beam appears to have a dark 'shade' or 'cutoff' at the very top of the light beam. I've never experienced this on any other vehicle and i attribute it to the one bulb system with a 'shutter' this model uses for low and high beams. The high beam is doing what the low beam should be doing. Low beams are completely useless in heavy fog, this is contrary to every other vehicle i've owned. When driving at night, i must resort to high beams when i shouldn't need to. This is especially a factor when descending hills and driving through turns and corners. The headlights on the last three vehicles i've owned were far superior in every way compared to the headlights in the 2012 chrysler 200 touring model sedan. I took the car to a aaashop in glen burnie, md, the service manager said an adjustment would probably not make any difference and the cost was nearly $55.00. I have not taken the car to a chrysler dealer because i was quoted $115.00 for an 'adjustment'. I like this car otherwise and i don't want to trade it in just because the headlights are lousy; they should be a lot better than they are. There are hundreds of posts on the internet of owners having the same issues with the headlights on this model as me. I purchased this vehicle used in march of 2012 and it now has 38,500 miles. Thank you.
While driving 15mph in a 25mph zone due to not being able to see the road on a downgrade i almost hit an animal and coming close to also hitting a low center median being unable to see in front of my vehicle more than 10 feet or less. Informed chrysler and as other people stated they want to do an adjustment and diagnosis of problem. I have and drive other vehicles and have not had this issue with anything else just this vehicle there is not enough light and the cutoff is seriously bad.
I've replaced my headlights twice now..both left and right.
Takata recall, abs and traction light are on they make a funny noise when i first start the car and start driving. But after i go so far or to 25mph, my lights come on and i brake just fine. I also have a issue with my turn signals, if my headlights are off my front left turning sognal works but if my headlights are on my front left turning signal does not work.
The contact owns a 2012 chrysler 200. The contact stated hat while driving 30 mph, he noticed that the headlights were not illumined properly.the vehicle was taken to the dealer but the dealer stated that there was nothing wrong with the vehicle. The dealer did however adjust the lighting. The manufacturer was contacted stated to the contact that if the dealer diagnosed no failures, then they would not assist. The failure mileage was 100 and the current mileage was 3,300.updated 08/28/12*lj
The contact owns a 2012 chrysler 200. The contact stated that when driving at various speeds with the low beam headlights illuminated, the light would only project a few feet and then it appeared that a curtain came down as the visibility became limited. The failure recurred numerous times. The contact entered a residential garage andnoticed that the lights projected an irregular shaped line on the garage wall and light only appeared below the line. The vehicle was taken to a dealer for diagnosis who provided no assistance. The manufacturer was also notified but offered no assistance. The failure and current mileage was 700. Updated 12/21/12*lj updated 1/9/2013
The contact owns a 2012 chrysler 200. While driving 20 mph, whenever the contact activated the turn signal, the windshield wipers activated. While driving, the driver side headrest popped off. The vehicle was taken to a dealer where it was diagnosed that the headrest needed to be replaced. The turn signal issue could not be diagnosed. The manufacturer was not made aware of the failures. The failure mileage was 38,500.
The contact owns a 2012 chrysler 200. The contact stated that while driving 60 mph, the vehicle stalled and the steering wheel ceased. The contact stated that there were no warning lights illuminated. The contact restarted the vehicle however, while driving and making a left turn the vehicle stalled. The vehicle was taken to ourisman chrysler jeep dodge of alexandria located at 5900 richmond hwy, alexandria, va 22303, to be diagnosed. The contact was informed that the fuel pump and fuel tank needed to be replaced. The vehicle was not repaired. The manufacturer was informed of failure. The failure mileage was approximately 114,000.
The contact owns a 2012 chrysler 200. The contact stated that after having his vehicle serviced for nhtsa campaign number: 13v282000 (air bags , electrical system) the check engine light illuminated at 50 mph. The vehicle was taken to a the dealer for inspection and they stated that the evac hose needed to be replaced due to the fact that a rodent had eaten the hose. The vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was 33,122. Updated 02/11/14*ljthe consumer stated there was a problem with the fuel tank evaporate hose.
This car was bought for advertised miles per gallon (mpg) was 31mpg, but on the highway it is only getting about 15mpg. This car is either defective or chrysler has embarked on major false advertising or fraud campaign in which millions of people bought this car thinking they would get 31mpg, but are paying twice as much in gas instead of saving money. If you think you are getting 31mpg on highway, but only get 15mpg, that means you run out of gas on the highway and an accident can occur either while the car is slowing down in the lane, or after it is pushed into shoulder, which is still dangerous. There are hundreds of reviews on the internet with same problem - not getting gas mileage. Please force chrysler to take back these cars because it is either false advertising and consumer fraud for advertising 31mpg, or defective for failing to be efficient with gas mileage since they are not getting the performance these cars were supposedly manufactured & designed for. There are also unknown problems with transmission and engine. I'm taking car to dealership today to investigate/service, but i was told by the sales manager, they would not take the car back and give me a new car. It has all these problems, costing me money and possible injury due to the prospect of running out of gas so frequently!the gas tank size is 16.9 gallons, so at 31mpg, i should get close to 523 miles, but we only get about 250!we fill up gas tank every week, after only driving 36 miles roundtrip to/from work, mostly on highway. I believe we are being defrauded by being sold defective cars that do not perform as advertised, and which can cause injury as a result. I shouldnt be stuck with this car, paying excessive gas prices due to constantly refilling a gas tank, because this car burns up all the gas so fast! is it a defect or consumer fraud? i want this car recalled, and i want my money back!
Takata recall the tipm has malfunctioned car will not function of start
The contact owns a 2012 chrysler 200. The contact stated that when the key was turned over, the lights flickered for the gauges and an abnormal noise emitted from the fuel pump and the vehicle failed to start. The vehicle was towed to the dealer but was not diagnosed or repaired. The manufacturer was notified of the failure. The failure mileage was not available.
Stopped at a red light, up until then car was driving fine, made a left turn and the 200 loss power and stalled out. The etc light and traction control light came on out the corner of my eye, next thing i know i was plowed into by another car. After doing more research, i have seen this problem come up time after time. The electronic throttle actually has plastic gears, plastic gears that control the opening of the throttle valve im sure those teeth will wear out on nearly every car and cause problems.
Totally integrated control module has failed leaving my car unable to start and once started have lurches in acceleration. Will crank but not start.
I have a 2012 chrysler 200 that stalls randomly. I have taken it in for service and diagnostic services and no results. The system has absolutely no codes stored in the system. It happens randomly while the vehicle is stationary and in motion. I have seen a lot of complaints with the same thing happening to people. It has left me in extremely dangerous situations many times. I do not feel comfortable or safe driving this car. This needs to be investigated as i have learned it has been affecting years from 2011 to 2016
4 cylinder 2.7l engine city gas mileage is only 13.5 mpg.my 2012 dodge grand caravan with a 3.6l v-6 gets 15 mpg.the 200 should be getting at least 18-20 mpg.my 2010 toyota corolla gets 23 mpg with the same type of city driving.there are people complaining all over the web about the excessive fuel consumption problem.chrysler should fix the problem and do a recall.minimum they should install an eco mode button to bring the mpg up to the advertised mpg.the transmission shift points should be lowered so the engine does not rev to 3000 rpms on every shift.it is ridiculous that the v6 version gets better mpg.imagine all the people that chose to go with the 4 cylinder to save on gas.chrysler knows this problem and should have eliminated the 4 cylinder option altogether but chose to offer it so sales would not go down for not offering a 4 cylinder option.chrysler should be penalized for this, not the consumer.
Takata recall power loss hesitation stalls engine light codes p0300 p0306 says cylinder 6 misfire had to go to dealer cause nothing fixes it idle is ok driving it hesitates engine losses power replaced all on code list won't fix has many complaints on this and chrysler can't figure it out why is it there is not an investigation going on people have to keep paying out of pocket on a defect in the mitsubishi 3.6l flex fuel gas motor
Engine shuts off on highway going full speed limit surrounded by heavy traffic. I was terrified. The engine light comes on & can't get car started. Then car starts & engine light goes away. Not to mention transmission is leaking & new transmission was put in 2015. Chrysler can't get me in until 4/19/18 bc its busy season. This may be why windshield wipers come on everytime i turn left.
This car was bought new with approx 300 milesbrought from a dealer's inventory in kokomo, in to one in northern kentucky, where it was bought 11 may ,2012..it had been on the previous dealer's lot, as part of inventory, i believe since sep,2011. In total it has stalled while stopped at a light 2 separate times..twice it has either quit while slowing or downshifted causing quite a violent throw forward of persons in their seats while at a relatively slow speed coming to a stop...in the old days it would be the jerk you get while popping a clutch to get a car started with a bad battery.. The third time it stalled was backing out of our driveway...we are now approaching 1000 total miles on the car with less than a month of ownership...made first visit to a dealer service 30 may 2012,..pcm code was updated,but could not duplicate problem..have had one jerky downshift since then ..this has been the recurring theme of many of these instances written up on blogs concerning this model over last 2 years..side note..this car has remote start capability on the key fob..i noticed a recall last year for some vehicles where they noticed the circuit board inside a fob had vibrated loose, and somehow was sending signals to some component in the car which was causing it to stop...ie. No codes associated with a malfunction like that...might be something to look at too.twice also, the hint of an electrical smell has been detected...same smell i experienced when the pcm on my 1993 ford van cooked itself a couple years ago..at first i wrote it off as a new car thing..but combine that with present and past experiences...well, the connection may not be coincidental.
Car has been acting funny but parked in a customer parking lot and when i tried to start car it stated severe problem and would not turn over. With my low miles i cant believe that a fuel pump could go.
Fuel pump failure, triggered heavy gasoline smell in the car suffocating breathing
The car stalls out!!!check engine light comes on and the car stops on the highway!!i was driving at a low rate of speed and the car just quit. It refused to start for about 5minutes.
I have been tiwed twice a d stuck on side of the road 4 times. I'll be driving along when everything just quits. Engine, power steering and power brakes. One time i was just about to get on a highway. Couldn't get car 100% off road. Very dangerous. When i try to restart car it trys to start. I let go of key and cajr just keeps trying to start. After being towed twice car started right up. So when it quits i give it about 10-15 minutes and it starts. Googled and people having same problem. Upon investigating i found that chrysler, jeep has been having this problem since 2011 and did a recall on the 2015s. If they know there is a problem, why aren't they fixing it??
The contact owns a 2012 chrysler 200. The contact stated that the front driver side door started to smoke. The contact stated the she attempted to extinguish the fire with water however, she was unable. The fire department was called and extinguished the fire. The contact a disable person, was scared for her safety and the safety of others. The contact called the dealer where she schedule an appointment and later taken the vehicle to lone star chrysler dodge jeep ram dealer, (8811 interstate 35 access rd, san antonio, tx 78211) but was not diagnosed or repaired. The vehicle was not repaired. The contact stated that now the driver side door failed to lock. The manufacturer was made aware of the failure and sent out a third party and the contact was informed that the door was badly burned and there was noting else they could do. The failure mileage was approximately unknown.
The contact owns a 2012 chrysler 200. The contact stated that when taking off from being idle, the accelerator pedal was depressed but the vehicle failed to respond. The failure recurred on numerous occasions. The vehicle was not diagnosed or repaired. The manufacturer was not made aware of the failure. The approximate failure mileage was 60,000.updated 4/29/15the consumer also stated the vehicle stalled at stop signs. Updated 05/05/15
My transmission is slipping and not performing the way it should.sometimes my car shifts hard and sometimes it won't shift out until it reaches 5 or 6000 rpms which is almost in the red zone.when going up a hill or incline it hesitates and jerks.i called several dealerships only to be told that there were multiple cars ahead of mine that were just sitting there with the same problem.i was told that they were waiting on a call from corporate to fix the problem. To this day it has not happened.also, my airbag light has been on for almost four months now.they said they did not have a fix for it yet. Just recently there is a knocking noise coming from the passenger side dashboard. An ongoing problem has been the noise from the front brakes when i am backing up. I was told there was no fix yet for that problem. As of this day, there still is no fix for it. I am still driving my car because i can't just leave it to sit at the dealership waiting on repairs. As you all know, they do not give out loaner vehicles any more at least not in arkansas.
Passenger side heater stopped working. Vehicle turns off while in drive and moving.
The contact owns a 2012 chrysler 200. The contact stated that the vehicle made an abnormal sound when the gear was shifted. The failure recurred, but was not diagnosed or repaired. The manufacturer was not made aware of the failure. The failure mileage was 33,000.
Service shift linkage message came on, what my dealer found, prndl display circuit shorted to ground replaced electronic shift module and reprogramed. @ a cost of 582.98
Car started kicking back, had to accelerate to stop the kicking.then while parking the steering wheel locked up and engine died.kept starting and it kept stalling.
While driving, attempted turn was made going approx. 10mph and the vehicle completely shut down without warning lights or anything. Once shut down i am able to restart but having this issue remain is frustrating. The vehicle has been taken to the dealership several times and each time no code is found and nothing is able to be done. Having this issue can cause serious damage and is extremely dangerous especially since i have children and i fear for our safety.
Purchased vehicle on nov.1st.2013.noticed when turning off vehicle there is a loud clicking sound on front right of vehicle.had it checked by a mechanic and was informed that there was a sensor malfunction near the timing cover.went to dealership and was told that this was normal for this model and make of vehicle.someone is wrong,either the mechanic or the dealership.who?
The first time i drove this car and snow i could barely keep it on the road.i have been driving in michigan for 24 years and i have never had a car that handled this poorly in the snow.i took the car to my dealership and they told me it is a common problem but chrysler does not have a solution for it.since then the dealer has split a set of snow tires with me but it only partially helps the problem.the car is terrifying to drive in any snow conditions regardless of the snow tires.it moves from side to side in the snow and can barely be kept on the road.i have a 2 wheel dr. Truck with no wait in it and i'd prefer to drive that over the chrysler in the winter.
Transmission goes in to limp mode,does not go over 30 miles jerking speeding up and slowing down, won't start and check engine light comes on goes off.
Leaving my office, in traffic, the car would not accelerate. The max speed it would go to was only 40 mph, but the rpm's were high. By the time i got it to the dealership (about 20 minutes later), the problem had corrected itself. The dealership was unable to pull the code, so they told me to come back if it happened again.
I only have heat on the drivers side of the car. We just hit our 100,000 bumper to bumper warranty. Had the car in the shop twice with coolant smells. Mechanics never found a problem. Everywhere i read there are tons of complaints about this issue. This is a $1000.00 repair! a flush is $150-170. We have already done this.i'm ready to trade it in but i do love my car. Not sure about how i feel about chrysler knowing about a issue and not offering assistance with the repair. Maybe they better send out a massive rebate to old owners in hopes of them staying a customer.
Takatarecall- when driving car pulls back almost as if there is some type of transmission problem. There's shifting gears issues. Aa if it's confused as to what gear itwants to go into.
I have been tiwed twice a d stuck on side of the road 4 times. I'll be driving along when everything just quits. Engine, power steering and power brakes. One time i was just about to get on a highway. Couldn't get car 100% off road. Very dangerous. When i try to restart car it trys to start. I let go of key and cajr just keeps trying to start. After being towed twice car started right up. So when it quits i give it about 10-15 minutes and it starts. Googled and people having same problem. Upon investigating i found that chrysler, jeep has been having this problem since 2011 and did a recall on the 2015s. If they know there is a problem, why aren't they fixing it??
The contact owns a 2012 chrysler 200. While driving various speeds and shifting gears, the vehicle shut off without warning. When the vehicle was shut off and restarted, it resumed normal operation. The contact took the vehicle to steve landers chrysler dodge jeep ram (401 colonel glenn plaza loop, little rock, ar 72210, (501) 404-9103) where it was diagnosed and an unknown part was repaired. The diagnosis and repair specifics were not disclosed. The failure recurred after the repair. The manufacturer was not notified of the failure. The failure mileage was 105,000. The vin was unknown.
After owning my car for only a few months the check engine light came on and a minute later the electronic throttle control light and then the electronic stability control light. After taking my car to kendall dodge chrysler jeep ram 5 times, an independent auto shop once and another visit to the dealership where the car was purchased my car is still having issues shifting from 2nd gear to 3rd. At least that's what the auto shop told me the problem is, with the transmission. I hit the gas and the car clunkers and jerks like a manual car when i'm just lightly pressing on the gas. The car doesn't even have 52,000 miles. I've had it less than a year and half the time it's been in and out of repair shops.
This car was bought new with approx 300 milesbrought from a dealer's inventory in kokomo, in to one in northern kentucky, where it was bought 11 may ,2012..it had been on the previous dealer's lot, as part of inventory, i believe since sep,2011. In total it has stalled while stopped at a light 2 separate times..twice it has either quit while slowing or downshifted causing quite a violent throw forward of persons in their seats while at a relatively slow speed coming to a stop...in the old days it would be the jerk you get while popping a clutch to get a car started with a bad battery.. The third time it stalled was backing out of our driveway...we are now approaching 1000 total miles on the car with less than a month of ownership...made first visit to a dealer service 30 may 2012,..pcm code was updated,but could not duplicate problem..have had one jerky downshift since then ..this has been the recurring theme of many of these instances written up on blogs concerning this model over last 2 years..side note..this car has remote start capability on the key fob..i noticed a recall last year for some vehicles where they noticed the circuit board inside a fob had vibrated loose, and somehow was sending signals to some component in the car which was causing it to stop...ie. No codes associated with a malfunction like that...might be something to look at too.twice also, the hint of an electrical smell has been detected...same smell i experienced when the pcm on my 1993 ford van cooked itself a couple years ago..at first i wrote it off as a new car thing..but combine that with present and past experiences...well, the connection may not be coincidental.
Transmission rebuild and three torque convertors in 6 moheater warm on left cool on rightengine stalls on highwayheat worked when taken to draler.they replaced sa clicking blend door actuatorin the morning there was warm air on the left and cool air on the right'dealer says need a heater core and radiator.this happened overnight?recall onairbags.no airbag light on at dealer,they flashed the tipm as per recall,now airbag light is on code reads replace occupant controle module.they claim this not on the recall,11v315000
Brakes rotors bushingsengine has whine and what sounds like a missclicking noise on start up, clicking when turning ignition key withoht starting completely, and clicks when turning key off.salesman says he called chrysler and was told the 200 car is made to veer to the right to stop driver who might accidentally go to sleep from entering oncoming traffic. Dealership said call warranty.had this 2012 car a with 46k that was a rental for afewdays so far its engine is quite noisy.calling warranty company to make appt to have car checked out.
The contact owns a 2012 chrysler 200. The contact stated that when driving between 16-22 mph, the vehicle would hesitate. The vehicle was taken to the dealer for inspection where they stated that the vehicle was changing gears as it was designed. The vehicle was not repaired. The contact also stated that the steering wheel seized without warning. The manufacturer was notified and stated that there were no recalls on the vehicle. The failure mileage was 2,000. The consumer stated the very day they picked the vehicle up, it stalled in the entrance way. The dealer claimed, the vehicle ran out of gas. As her son drove the vehicle home, he noticed when coasting at low speeds, the vehicle would kick back. The mechanic stated the jerk/kick was from the engine shifting gears. The kicking would go away, when the accelerator pedal was pressed.when her son turned the steering wheel to the right and then straightened it out, by turning the wheel to the left, the steering wheel locked up.he put the vehicle in park and shut off the engine. He tried to re-start the vehicle several times, but the engine would rev up tight until it was about to start, but would immediately shut off.the vehicle was towed to the dealer, where they found a code, but it had nothing to with the problem, that was being experienced. Updated 01/16/13
The abs and terrain lights stay on, when car reaches 60 mph it pulls.
I have reported in the past in regard to our 2012 chrysler 200 with 3.6 v6 engine of episodes of pmu shut down while driving at slow speed.the manufacturer warranty still covered the vehicle when we first experienced this problem we now are over 60,000 miles as chrysler has not been able to resolve this problem yet.the engine quit while driving (3 times additional times), at highway speeds.we were able to get to the shoulder of the highway , without power steering and brakes;all computer support systems failed, but all electrical systems still worked. The problem has been checked 4 times after each of the stalling episodes, the pmu computer shows no codes (per chrysler and the dealer) there is no problem to fix.the last episode the esc dash lite came on, followed by the brakeand the abs lights started flashing on & off which caused the speedometer to bounce up and down while the ability to maintain speed or accelerate to maintain speed was lost(again there were no codes) the last2 times this happen were 11/30/16 & 12/1/16.i have talked to chrysler fiatbut the dealer ani i have not been able to receive any service or suggestion in resolving this pmu problem.it feels like they are not concerned that there is a great safety issue that could result in injury or death. There should be some information available, as this has been a problem thathave been ongoing for many models with the 3.6 v-6 engine and over a number of years, which chrysler has issued customer service notices to dealers and replaced pmu. Recalls have been avoided as there has not been any serious accidents, injuries, or deaths. If you have had this type of problem with your 3.6 v6 contact chrysler and the nhtsa.
It has been increasingly difficult to see at night when driving my chrysler 200 2012 in low lit areas due to the headlight beams.less light? aimed low?i have to drive far slower than posted around bends at night. I don't recall this issue when i bought the car brand new.i have had it one year and have just over 10,000 miles.i don't usually have to drive at night other than my well lit neighborhood ,so this could have easily gone unnoticed.either way, this terrifies me.the other issue i have is a jerk when shifting to reverse or drive. It is a loud clunk and i feel the vibration. I will not drive at night in low light areas until resolved.i also feel the car pulls to the right when driving. I will contact the dealer soon, until then i just don't feel safe driving while on dark roads.
Car was in motion leaving a shopping area, turning right and accelerating onto a 4 lanehighway.as 45 mph was achieved, the car decelerated and stalled.the check engine light and the electronic throttle control light came on.i looked up the etc information and read i may be able to try again to drive the car.i did try and rolled on the shoulder for about 1/4 mile before having to accelerate though an intersection.at that point, car repeated the above failure and stalled.i was able to make a right turn and coast into a parking lot.the car was towed.while waiting on the tow, i read several reports of the same issue occurring in this model vehicle, often while driving on the interstate or in other dangerous locations like an intersection.this failure happened with no warning - no sputtering, hesitation or warning lights until the failure occurred. This failure could result in serious injury or death.it looks to me to be a known issue and should be subject to recall.
The contact owns a 2012 chrysler 200. While driving at an unknown speed, the electronic stability control warning indicator illuminated. The accelerator pedal was depressed, but the vehicle failed to respond. The vehicle was towed to oxmore chrysler dodge jeep ram (4520 shelbyville rd, louisville, ky 40207, (502) 895-4520) where it was diagnosed that the electronic stability control module needed to be replaced. The vehicle was not repaired. The manufacturer was not notified of the failure. The approximate failure mileage was 40,000.
The contact owns a 2012 chrysler 200. While driving 55 mph, the vehicle jerked and stalled without warning. The vehicle was able to coast to the side of the road where it failed to restart. The vehicle was towed to darcars chrysler dodge jeep ram of silver spring (12511 prosperity dr, silver spring, md 20904, (301) 622-0010) where it was diagnosed that the integrated power module needed to be replaced. The vehicle was repaired, but the failure recurred eight times. The vehicle was taken to an independent mechanic where a diagnostic test was completed, but a failure code could not be found. The manufacturer was notified of the failure and informed the contact to take the vehicle back to the dealer. The approximate failure mileage was 80,000.
The contact owns a 2012 chrysler 200. When the accelerator pedal was depressed, the vehicle failed to accelerate. In addition, the vehicle hesitated and stalled without warning. The vehicle was able to be restarted, but the failure recurred. The dealer was unable to diagnose the cause of the failure. The manufacturer was not notified. The approximate failure mileage was 67,000.
Takata recall ----while driving, in motion, to pick up my daughter from schooli start to hear a winding sound. My electrical system that powers the radio and uconnect system starts to shut down.my abs light andesc light comes on and im startingto smell a burning in the car,while this winding sound is getting louder, smoke is coming from the hood.the timing or transmission is disabled , the car shutsdownin the middle of the road, in front of the school exit. We could have been struck from behind or the side of the vehicle. Car smellslike it caught fire.
The car randomly loses power along with the power steering and cuts off. I could be driving for 30 mins and it'll be just fine then out of no where it may cut off at stop light, while i'm decelerating or even trying to gas up. It has cut off numerous times on the highway without any warning or light and i'll only know by the sudden loss of power steering or noticing the rpm gauge dropping to 0. Sometimes it'll start up just fine right afterwards like nothing happened and sometimes it'll take a minute or two to start up. It may start a right back up then cut right back off or it may start up and be fine until the next day. Sometimes it only starts back up when i disconnect the negative battery terminal for a few seconds.
The vehicle stalls out - power is shut-off without any notice.the vehicle becomes tdisable while trying to drive.this occurs three times this year.the only way to get the vehicle operating again it to put in park and restart the car.the steering while locks up as well.i have to take the highway to work everyday.most of the instances when this happens i'm not driving on the highway.the stalling of the car occurs when you drive about 2-3 miles.the car bears left and starts to stalled out.it lost power.every time this problem occurred it happens while the car is in motion.
The contact owns a 2012 chrysler 200. The contact stated that the transmission failed to shift gear without warning. The contact mentioned that sometimes the shift lever would become stuck to the first gear and the vehicle failed to accelerate over 30 mph. The vehicle was taken to a dealer. The technician diagnosed that the power control module and valve body were defective and needed to be replaced. The vehicle was repaired but the failure recurred. The manufacturer was notified of the failure. The failure mileage was 13,500.
While driving the car.. Thecars electrical system stopped working. While driving on the freeway the car shut down and was almost in severe car accident because of the issue.there is a new battery and the alternator has been checked and is in great working condition.
A few weeks ago, the transmission failed while i was driving on the highway, left me stranded, and without a car for ten days. It seems that chrysler is aware of a drum issue within the transmission in this make and model vehicle and in fact has manufactured a specific 'repair kit' for just this scenario. This repair cost me over $2,600, including a three day car rental for a period where i could no long beg rides to work and had to rent a car at my own expense. Attached are the repair and rental car bills. In my 40 years of car ownership, including several new cars, i have never heard of such significant issue being experience in a vehicle with such low mileage, 61,800, on a well and regularly maintained vehicle. Therefore, i respectfully request that your administration review this incident and record them as a part of a larger case designed to encourage chrysler 'do the right thing' and initiate a recall (silent or public) to correct this known transmission issue.
Rpm s goes up high while driving car will change gears speed slows down have to pull to side of road or freeway turn off ignition and restart car then the car will run fine until the next time it occurs again which is very often also whenat light or stop sign vehicle will go dead took car for repairs transmission problem do not know why there is not a recall on this car looked on internet there a lot of people that have the same problem with their transmission when i called chrysler was told my car was not on the recall list had to pay out of pocket for a problem that a lot of people are dealing with
Entering the on-ramp of a 65 mph highway, at the hov lane (so the left most lane), the car wouldn't accelerate and started to decline in speed. I was almost rear ended several times. I had to cut across 4 lanes of traffic to exit. I called the dealership and told them this had happened before, but at that time they couldn't recreate the code, and that they told me to bring it in if it happened again. I took the car in, they got the code, and stated my car thinks it's overheating, so it's shutting itself down. I told them that wasn't possible since i hadn't driven the car in 2 days and the distance from my house to the on-ramp was probably less than a mile. The guy then told me that if i started it up, and the problem seemed to be better i could take it since it was a saturday and the only service techs they had could only perform oil changes. I drove it to my friend's house about 2 miles away and left it. Unfortunately i had to drive home, and to/from work today. I called the dealer from work, and scheduled to drop it off the next morning since that was their next availability.the guy said he'll have to keep it until the problem happens again. I stated that would be inconvenient since they don't do loaner cars, and the last time the problem happened was about 3k miles ago. Hopefully he can fix it based off of the code they pulled a few days ago.this stinks! the reason i bought a brand new car was for reliability.
Vehicle stalled and would not start while driving (2 times )towed to dealer as (both times) tow driver could not restart.dealer reported no computer codes and car started after car started on problem.there appears to be common safety hazard that has been experienced by many owners, that reportly chrysler and nhtsa agreed upon a resolution to avoid a recall by chrysler of this safety hazard in sept 2012.chrysler doesn't acknowledge and not sharing this information with dealers so they can take corrective action. Various attempts tried to resolve this hazardouscondition have included replacing the powertrain module, camscope replacement, monitoring the on board with a copilot computer-which also showed no codes.the dealer did say that chrysler suggested an additional module be added to the on board computer, but none of their customers returned a third or more times as previous attempts were unsuccessful and appeared to give up.this life threatening safety hazard needs to beinvestigated and resolved, as we were driving on aroadway and the motor just shut off.,if this not resolved it will sometime cause injuries or deaths, which could end up with a recall something that chrysler possible replacement of on computers.
When slowing down almost to a stop, the vehicle downshifts hard. It cause a shutter or jerk and you can feel even in the brakes. Feels awful and cannot be normal. Also, when accelerating, the vehicle pulls hard to the right.
Shifted the vehicle into reverse, when the vehicle is then put into drive there is a loud bang.
Takata recalli am sure you have probably received hundreds of complaints regarding this issue, as i have researched it online & seen the long list of other frustrated owners.this is ridiculous, it is a known common problem that the heating core in these chrysler 200 on the passenger side does not work...it blows out cold air. Temperatures are now below freezing. I do not see fairness that any owners have to spend a grand or more replacing something that obviously was malfunctioning in most of their vehicles & many complaints (including mine) have been sent to chrysler. This has been on an issue now since the season changed & it is cold. I do not have a grand to spend nor do i have warranty anymore .
No heat on passenger side of vehicle, blows cold air.however, there is heat on driver's side.i took it to dealership broke heater door/actuator.i get to the part that needs repair i was given a quote of $650 to remove dashboard- labor cost., repair/replace cost is not part of the $650.reviews showthere have been numerous complaint with this same problem for 2012 200 chrysler.it 's a safety issue because passenger side windshield does not defrost because of cold air being blown out . . . Doesn't clear the windshield in cold weather nor does it keep windshield clear in rainy weather. Why hasn't a mandatory recall been issued to to manufacturer to correct/replace part. Car has approximately 75,000 miles.blows cold air both when stationary and while in motion on all, road ways, all the time no matter if i am turning, braking or driving straight --- no heat on passenger side.
I bought my car brand new in 2012 from chryaler dodge and jeep in springfield pa. I babe around 96,000 miles on my car and this will now be the third alternator that has been put in my vehicle. From what i know, the alternator should last up between 80,000 to 100,000 miles. I believe there has to have been a defect with my specific car. Along with some of the other recall items i am now reading about with my model, having kids, i am increasingly concerned about my health andsaftey driving this vehicle. I want to know what can be done about this on your end
I own a 2012 chrysler 200, the engine stops/fails about every two months while braking or while stopped. This is dangerous as it can stop anywhere and they might rear end the car or something. I have taken my car to the chrysler dealership 4 different times with the same issue, the first time they changed the pcm. After about 2 months the car's engine stopped while braking or while at a stoplight. The 2nd and 3rd time i took the car they did not find anything wrong with the car and gave it to me after a couple of days. The 4th time when i took the car they said that it was the battery and they put in a new battery. Well about 2 days ago the car stopped again while at a stoplight. I have not taken the car to the dealership as they never find anything wrong with the vehicle. I am tired of them not finding what is wrong with the car. I believe that i speak for many chrysler 200 owners when i say that an investigation needs to be done for the whole chrysler group, especially to the 200, which have many complaints online and none one seems to find the solution. Please investigate this for the safety of the drivers. I am so sick and tired of the mopar mechanics not finding anything. I do not know if the issue is with the pcm, computer, or engine. Please investigate.
Without any symptoms or warning my 2012 chrysler 200 experienced total transmission failure while driving in heavy city traffic.while turning left at an intersection i lost all gears. I was nearly rear ended by a city bus.the chrysler dealership that the car was towed to states this is a common issue with the 200 v6.
Transmission would not go into reverse.kept going to park.could not backup03
I bought my 2012 chrysler 200 in 2013.i 've had a recurring problem with the engine running hot because some malfunction prevents the coolant from circulating through the engine.i have spent over $2000.00 trying to fix this problem and now my mechanic tells me the engine is no good and i'll need a new one.this happens when i'm driving. The car would run hot, i'd tow it in and my mechanic would fix it. And within a month or two, the problem would occur again. My mechanic ran diagnostics, he rebooted the computer systems and he gets the coolant flowing again but within weeks or a month the same problem reoccurs. I don't drive far to work approx. 10 miles daily commute.i may take a road trip on occasion but there is no unusual wear or tear on the vehicle. Im reporting this problem aug 2016 but this has been a recurring issue overthe years and the car is just for years old.i bought it used in 2013. I've spent so much money fixing the same problem and the car's problem always seems resolved until a few months down the road i have to fix it again. I haven't even paid the car off and its kaput and ready for the graveyard? this really is something chrysler needs to step up to the plate and fix.i need a new engine now and i've already spent over $2000.00 trying to fix this issue.
While driving 45 mph on a highway, my car just died. The speedometer fluncuated, all lights flashed on and off, then just died completely.
The contact owns a 2012 chrysler 200. While driving approximately 35 mph, the heater and the front passenger side defroster failed to function when activated. In addition, the transmission jerked while shifting from park into the reverse position on numerous times. The vehicle was not diagnosed or repaired. The manufacturer was notified of the issue. The approximate failure mileage was 56,000.
2012 chrysler 200 6xx,xxx miles. Car will shift to neutral while in operation; shifts out of gear when accelerating causing several near accidents while in traffic. Has left vehicle immobile in roadway.
The contact owns a 2012 chrysler 200. The contact stated that while driving 20 mph, the steering wheel became difficult to turn. The vehicle was taken to the dealer for inspection where they stated that there was no power steering fluid in the vehicle. The vehicle was replenished with power steering fluid but the failure recurred. The also contact stated that the power steering hose exploded and needed to be replaced. The vehicle was repaired. The manufacturer was not notified. The failure mileage was 6,047. The consumer stated there were numerous problems with the vehicle, such as a coolant leak, oil leak, air condition, the cd player did not work, the power steering hose burst, the wire harness, the transmission was replaced, the engine was noisy and the seat belt on the passenger side was not properly installed.the vehicle cut off several times. Updated 10/31/13
Took car in to dealership years ago to have head rest and airbags fixed. Received a notice by inputting my vin that these fixes were incomplete . Also discovered that the 3.6 pentastar engine from the factory had substandard engine bearings which could result in the engine seizure and the remedy was for the factory to replace the engine. My 2012 chrysler 200 was manufactured during this time frame, yet was never notified by the manufacturer of this dangerous condition.
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (air bags, seat belts). The part to do the repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The dealer and manufacturer were not contacted. The contact had not experienced a failure. Vin tool confirms parts not available. The consumer stated the vehicle was repaired.
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (seat belts, air bags). The part to do the repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The contact spoke to a dealer who was unaware of the recallthe manufacturer was not made aware of the issue. The contact had not experienced a failure. Vin tool confirms parts not available. Updated 07/11/17*lj*as
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign numbers: 16v668000 (air bags) and (seat belts); however, the part to do the repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. Vin tool confirms parts not available.
The contact owns a 2012 chrysler 200. Upon starting the vehicle, the air bag indicator illuminated. The contact previously received notification of nhtsa campaign number: 16v668000 (seat belts, air bags). The part to do the repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue and stated that parts for the recall repair were not available and that they did not know whether the air bag indicator illuminating was due to the recall or not. The contact spoke to central jeep chrysler dodge ram of norwood (56 boston-providence turnpike, norwood, ma 02062) who stated that parts for the recall repair were not available; however, they could diagnose the failure for a fee. The vehicle was not diagnosed or repaired. The approximate failure mileage was 115,000. Vin tool confirms parts not available.
The contact owns a 2012 chrysler 200. While driving, the seat belt warning indicator illuminated. The vehicle was taken to the local dealer (bill luke chrysler jeep dodge and ram located at 2425 w camelback rd phoenix, az 85015) where it was diagnosed that the seat belt module needed to be repaired. The manufacturer was made of the failure and placed the contact on the fast track system where they would reach out to him when the remedy was available. The contact paid for the repair and requested reimbursement. The failure mileage was 50,000.
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (seat belts, air bags); however, the part to do the repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The contact called a local dealer (carl burger chrysler jeep dodge ram world (8355 hercules st, la mesa, ca 91942) and was informed that the part to do the repair was not available. The manufacturer was not made aware of the issue. The contact had not experienced a failure. The vin was not available.
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (air bags, seat belt); however, the part for the recall repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The contact stated that the air bag warning indicator illuminated. The approximate failure mileage was 70,000. The manufacturer was not made aware of the failure. Vin tool confirms parts not available.updated 05/04/17*lj
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16668000 (air bags, seat belts); however, the part to do the repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. Beaver toyota of saint augustine was contacted about the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. Vin tool confirms parts not available.
Takata recall.november 13, 2016 i received vis usps a recall for the occupant restraint controller.today is september 4, 2017...thats 10 months and still nothing has been done.
The contact owned a 2012 chrysler 200. While the contact's granddaughter was driving 10 mph and making a left turn, another vehicle crashed into the front passenger side. The air bags failed to deploy and the driver side seat belt failed to restrain the driver, which caused her head to hit the steering wheel. The driver sustained bruising to the forehead, but medical attention was not required. The front seat passenger was uninjured. A police report was filed. The vehicle was driven to a local auto body shop where it was deemed a total loss. The contact received notification of nhtsa campaign number: 16v668000 (air bags, seat belts) several months prior to the failure. The dealer and manufacturer were not notified as the recall notice stated that owners would receive a second notice when remedy parts become available. The failure mileage was 80,566.
The contact owns a 2012 chrysler 200. The contact stated that within two weeks of owning the vehicle, the head rest restraint deployed without warning. The vehicle was included in nhtsa campaign numbers: 13v282000 (electrical system, air bags), 16v668000 (seat belts, air bags), and 17v640000 (seats, air bags). The dealer (autonation usa corpus christi, 3115 s padre island dr, corpus christi, tx 78415-1815, 361-217-6733) was notified of the failure. The vehicle was not repaired. The manufacturer was notified of the failure. The approximate failure mileage was 52,000.
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (seat belts, air bags); however, the part needed for the repair was not available. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The vehicle was not diagnosed or repaired. The manufacturer was made aware of the issue. The contact had not experienced a failure. Vin tool confirms parts not available.
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (air bags, seat belts); however, the parts to do the repair were unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The manufacturer was notified of the issue. The contact had not experienced a failure. Vin tool confirms parts not available.
The contact owns a 2012 chrysler 200. The contact stated that the rear passenger seat belt failed to unlock and retract. The contact had to cut the seat belt to be able to release the child from the seat. The vehicle was not diagnosed or repaired. The manufacturer was made aware of the failure. The approximate failure mileage was 37,000.
Received a recall notice but no parts are available for a fix.been waiting about 6 months with no action.how do i get the company moving on providing corrective action?
I have contacted the douglas chrysler dealer in venice fl to schedule repair of the occupant restraint controller - safety recall s61/nhtsa 16v-668.i was informed that chrysler releases about 1 part a week to this dealer, that there are about 20 to 30 people on a waiting list waiting for parts and that it will take a while before the vehicle is repaired.i am asking for your assistance in securing replacement parts faster from chrysler.thank you
Vehicle was recalled ten months ago (16v-668). Parts are still not available. Local chrysler dealership is stating parts will not be available until 2018. Make chrysler fix this safety concern!
I received a recall notice months ago and have had not response to checking and or repairing recall parts and or no contact, i have registeredat recalls. Mopar. Com with no response to date (waiting months)
My seat pops out sometime when driving. It happens anytime whether in motion or stationary hence the airbag light is on.
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (seat belts, air bags). The part to do the repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The contact spoke to poulin chrysler dodge jeep ram (401 n main st, rochester, nh 03867) who stated that the parts were not yet available and they did not know when they would be available. The contact had not experienced a failure.
Takata recall. The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (seat belts, air bags); however, the parts to do the repair were unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The vehicle was taken to the local dealer (sheets chrysler dodge jeep ram located at 250 auto plaza dr, beckley, wv 25801; (304) 252-4555) where it was confirmed that the parts were not available for the recall remedy. The manufacturer was not contacted. The contact had not experienced a failure. Vin tool confirms parts not available.
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (air bags, seat belts); however, the part to do the repair was unavailable the contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. An unknown chrysler dealer was contacted and stated that the parts were unavailable. The manufacturer was not made aware of the issue. The contact had not experienced a failure. Vin tool confirms parts not available. Updated 08/03/17*ljupdated 08/29/2017
I received a letter back in january that a vehicle i own has a safety recall of "loss of airbag and seat belt pretensioner deployment capability during a crash. I emailed them back in february and was told i needed to wait they would get back to me as soon as possible, i emailed again in april was told the same thing it is now august. My son drives this car, would they be so laid back if it was one of their family members ?i would appreciate it, if you could tell me how i can take this further. Thank you
Takata recallunknown my car stalled out on the side of the road and i left it there to be picked up by my mechanic the next morning. I found out the next day that my car had been crashed and i went to the tow yard where the vehicle had been taken to retrieve my personal items from the vehicle and noticed that my airbags did not deploy. My car has been considered a total loss by geico car insurance. Geico claim number [xxx]. I still have my title, it is a rebuilt one. Geico has been taking their sweet time to reimburse me for my vehicle. The actual accident occurred on april 25th, 2017. The police report is inaccurate. Today is august 30th, 2017 and i'm still waiting on a check. The tow yard has apparently become the lienholder so i've been told and geico has to pay them off before they can pay me? i don't know it's crazy. There would be no lien if geico had handled this in a timely manner. I have had to come out of pocket to purchase a cheap car in the meantime while i wait. I have just recently received emails from carfax saying that my car may be at risk of being recalled so i put in my vin number ([xxx]) and it says that my chrysler 200 2012 is a s61. However, i was aware the passenger seatbelts were locked but i was still able to wrap the driver's belt around me. Furthermore, i've had numerous headlight issues in both headlights and the ac eventually stopped working. There was also a check engine light on that could not be turned off. I spoke with chrysler and they told me nothing can be done as far as reimbursement at this point because i have no possession of the vehicle. However, the title is still in my name and the possession issue is geico's fault. I am looking for some type of justice in this situation it could have been me in the crash. I am [xxx]and it says under federal law that my vehicle can be replaced. #16v-668information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6).
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (air bags, seat belts); however, the part to do the repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The dealer and manufacturer were not made aware of the issue. The contact had not experienced a failure. Vin tool confirms parts not available.updated 08/24/17*ljupdated 09/20/2017
The contact owns a 2012 chrysler 200. The contact stated that the recall notice for nhtsa campaign number: 16v668000 (air bags, seat belts) was received in september of 2016. After contacting the manufacturer on multiple occasions, the contact was informed that the parts needed for the recall remedy were still not available and no estimated time for receiving the parts could be provided. The local dealer was not notified. The contact had not experienced a failure. Vin tool confirms parts not available.
I've been notified for sometime now about a recall for my car. Nothing has been corrected yet in reference to the airbag and seat belt -constraint controls. What happens if i have an accident with these features still not corrected?
The air bag & seat belt tensioner may not deploy, replacement of occupant restraint controller is required.it's been over 6 months with no remedy provided by chrysler, this is unsatisfactory.[xxx] gilbert, azinformation redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6).'
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (seat belts, air bags); however, the part to do the repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The manufacturer was notified of the issue. The contact had not experienced a failure. Vin tool confirms parts not available.
Driving and interior lights dim down and get real bright spontaneously. Also my seat belt light and chime don't work all the time?? trans already slips when leaving town at a medium acceleration? only 75000 miles on the car.
The contact owns a 2012 chrysler 200. The contact received a recall notification for nhtsa campaign number: 16v668000 (seat belts, air bags); however, the parts to do the repair were unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repairs. The manufacturer was not made aware of the issue. The contact was informed that a second notification would be sent to owners in june of 2017. The contact had not experienced a failure.
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (seat belts, air bags); however, the parts to do the repair were unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The contact called the dealer (meadowland carmel at (877) 752-7220) where it was confirmed that the parts were not available for the recall remedy. The manufacturer was not made aware of the issue. The contact was informed that owners would receive a second notice when parts become available in august of 2017. The contact had not experienced a failure. Vin tool confirms parts not available. Updated 08/09/17*lj
No seat belt warning system visual or audio on passenger seat. Is this a violation? i thought tat this was a requirement.dealer states can not fix.
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (seat belts, air bags); however, the part to do the repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. The vin was not available.
I was driving straight forward, in the right lane of a four lane highway (two lanes in either direction). A car traveling in the opposite direction, lost control and crossed the highway, striking my car's front end. My car received extensive front end damage. The car was totaled, as was the other car. I was driving and my wife was in the front passenger seat. We were both wearing our seat belts. At the time of the impact, neither airbag deployed, nor did the seat belt pretensioners activate (locking the seat belts in place), causing serious injury to both of us, requiring hospital admittance in the intensive care unit, for myself. Police traffic crash report, photos and other documents are available if required, in the future. Also, i just received a re-call notice, dated october 1, 2016. Nhtsa 16v-668, concerning the car i was driving at the time of the crash...updated 01/04/17 *po - inj but not death as indicatedupdated 7/25/18*dt
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (seat belts, air bags); however, the part to do the repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair the manufacturer was notified of the issue. The vin was unknown. The contact had not experienced a failure. Vin tool confirms parts not available. Updated 01/25/17. Updated 03/03/17*lj
Its been several months now that i just recieved my safety recall notice and yet a dealership has not repair any of the recalls. Please address this asap before an accident does occur. Thank you
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number:16v668000 (seat belts, air bags) however, the part to do the repair was unavailable.the contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. A dealer was contacted and stated that the vehicle had no recalls and that the only problem the vehicle had involved a bolt. The contact had not experienced a failure. Vin tool confirms parts not available.
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (seat belts, air bags); however, the parts to do the repair were unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The lake shore dealer was contacted and confirmed that the parts were not available for the recall remedy. The manufacturer was not made aware of the issue. The contact had not experienced a failure. Vin tool confirms parts not available.updated 09/07/17*lj
The contact's spouse owns a 2012 chrysler 200. While the contact's spouse was driving 45 mph, her vehicle was cut off by another vehicle and crashed into a wall. The air bags failed to deploy. The contact sustained injuries to the c3/c4 cervical vertebrae and a laceration to the knee, which required medical attention. A police report was filed. The vehicle was towed to an independent facility. The vehicle was repaired; however, the contact was concerned that the air bags were never replaced. The vehicle was included in nhtsa campaign number: 16v668000 (seat belts, air bags). A dealer was not contacted. The manufacturer was notified of the failure. The approximate failure mileage was 64,000.
Takata recall. The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number:16v668000 (air bags, seat belts) and stated that the part was not available within a reasonable time frame to schedule the recall repair. The dealer did not give a specific date for when the part would become available. The manufacturer could not provide an estimated date for when the contact's vehicle would receive the recall repair. The contact was not experiencing a failure. Vin tool confirms parts not available.
Recall was issued in september 2016, for;"vehicles may experience loss of air bag and seat belt pretensioner deployment capability in certain crash events due to a shorting condition resulting in a negative voltage transient that travels to the occupant restraint controller via the front impact sensor wires."it is now july 2017, without an estimated repair time nor when or how the situation could be fixed.
I got into a car accident in may of 2016. My air bags did not deploy, as they should have given the speed i was going. I also was not notified of this recall until later that year. I have called and checked online to see when the parts would be in to have the recall issue solved and i have been told they do not have an eta and the parts aren't available.
The contact owned a 2012 chrysler 200. While the contact's partner was driving 25 mph, the driver crashed into a wall to prevent rear ending another vehicle. The driver sustained injuries to the back and neck, which required medical attention. The air bags failed to deploy. A police report was filed. The vehicle was towed from the scene and confirmed destroyed. A dealer was not contacted. The manufacturer was not made aware of the failure. The vin was included in nhtsa campaign number: 16v668000 (seat belts, air bags), but the vehicle had not been serviced. The approximate failure mileage was 147,000....updated 10/17/17 updated 9/5/18
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (seat belts, air bags); however, the parts to repair the vehicle were unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. Sunset dodge-chrysler-jeep-ram (7745 south tamiami trail, sarasota, fl 34231-6841, 941-922-2400) was contacted several times and informed him that they only received two replacement parts per month. The manufacturer was made aware of the issue. The contact had not experienced a failure. Parts distribution disconnect.
The contact owns a 2012 chrysler 200. The contact stated that while driving 20 mph, the steering wheel became difficult to turn. The vehicle was taken to the dealer for inspection where they stated that there was no power steering fluid in the vehicle. The vehicle was replenished with power steering fluid but the failure recurred. The also contact stated that the power steering hose exploded and needed to be replaced. The vehicle was repaired. The manufacturer was not notified. The failure mileage was 6,047. The consumer stated there were numerous problems with the vehicle, such as a coolant leak, oil leak, air condition, the cd player did not work, the power steering hose burst, the wire harness, the transmission was replaced, the engine was noisy and the seat belt on the passenger side was not properly installed.the vehicle cut off several times. Updated 10/31/13
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (seat belts, air bags); however, the parts to do the repairs were unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The dealer confirmed that the recall remedy was not available. The manufacturer was not notified of the issue. The contact had not experienced a failure. Vin tool confirms parts not available.
My airbag light is coming on while i'm driving and i am still under warranty.
The contact owns a 2012 chrysler 200. The contact received notifications for nhtsa campaign numbers: 16v668000 (seat belts, air bags) and 17v640000 (seats, air bags); however, the parts needed for the repairs were not available. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repairs. The vehicle was taken to roberson motors (3100 ryan dr. Se, salem, or 97301, (503) 363-4117), but the parts were not available for the repair. The manufacturer was not contacted. The contact had not experienced a failure. Parts distribution disconnect.
Recall date was september of 2016 and almost a year later the parts still have not be released to dealers to fix this issue.this seems like an excessive amount of time to wait for such an important recall issue
Takata recall. The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (air bags, seat belts); however, the part to do the repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The manufacturer was notified of the issue. The contact had not experienced a failure. Vin tool confirms parts not available.
On september of 2016, i received a recall notice stating that the potential loss of airbag and seat belt pretensioner deployment during a crash may increase the risk of injury.it also stated that when a remedy and parts were available, i would be notified.i have been driving this car for 7 months (probably for 5 years, since i purchased it new) without this needed protection, and there has been no notification yet.when can i expect chrysler to correct this problem?
Complaint: passenger seat belt gets stuck when buckled. You have to pull really hard to release the buckle. If i were to get in a wreck i could not get a passenger out of my passenger seat because its too hard to unbuckle.this occurs when car is moving and stationary. Heater problems: my passenger side heat is not working it is blowing cold air and will not defrost the passenger side. Only the driver side right vent blows warm air. This issue occurs when car is stationary and moving.
I had the seatbelt fixed due to recall but i almost got into accident as i could not pull the seatbelt . I felt like it was choking me . The second problem which is the current . I have been experiencing when you start up the car there are times it will start right away and there are times that i have to try it to start between 3 or 5 times. Brought the car to the mechanic 3 times in 2 weeks. . i have a brand new battery, not even a year old alternternator, spark plug is also new, brake is new and another parts was replaced which cost me $300. Today , december 19, 2019 i brought my car to the mechanic to have the problem diagnosed but on the 13 detected none of it has error. . please help me. I already spent so k in money to get it fix . I don't know what else the problem . Been to two mechanics and both of them can't find the problem. I can't afford to go back and forth to the mechanics and i am still making payments to the car. Please help!
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (seat belts, air bags); however, the parts to do the repair were unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The dealer was not contacted. The manufacturer was contacted by email at [email protected] and confirmed that the parts were not available for the recall remedy. The manufacturer was made aware of the issue. The contact had not experienced a failure. Vin tool confirms parts not available.
The contact owns a 2012 chrysler 200. While driving 10 mph, the tire pressure gauge malfunctioned, the seat belt warning indicator illuminated, and the air bag warning indicator illuminated. The warning indicators functioned normally after 20 minutes, but the air bag light remained illuminated and a tipm warning indicator flashed. The vehicle was not diagnosed or repaired. The vin was excluded from nhtsa campaign number: 13v282000 (air bags, electrical system). The failure mileage was approximately 70,000.
Takata recall.i have a recall on airbags and seatbelt transponder may not work in event of an accident.i refuse to drive this car and am not waiting until june 2017 for a repair.i want a buyback immediately....with incentive ...so i can get on with my life.a rental is being offered at this time .i am not satisfied and a buyback would make more sense.
Soon after i purchased my 2012 chrysler 200 s the rear safety belts began locking for no apparent reason. The lock was so harsh that the belt would have to be removed and reapplied. The restraint has continuously locked causing the passenger to be pinned to his or her seat. This has happened almost every time there is a passenger in the rear restraint no matter the speed the vehicle is traveling.
Takata recall. The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (seat belts, air bags) however, the part to do the repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. Vin tool confirms parts not available.
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign numbers: 13v282000 (air bags, electrical system) and 16v668000 (air bags, seat belts) however, the parts to do the repairs were unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repairs. The manufacturer was made aware of the issues. The contact had not experienced a failure. Vin tool confirms parts not available and parts distribution disconnect.
There was a recall on the airbag and seat belt pretensioner deployment capability on my car that started on october 1, 2016. When i got the recall notice in october it said that there was no current remedy. It's now december and there still is no remedy which means that the problem won't be fixed in the foreseeable future which is outrageous. If our lives are at risk because a car company can't get off its [xxx] and fix this, then the government needs to intervene. I don't feel safe driving my car because in the back of my mind i know that it might not protect me completely if i get in a crash which should not happen. This needs to be fixed now.information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6).
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (air bags, seat belts); however, the part for the recall repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The contact had not experienced a failure. The manufacturer was not made aware of the issue. Vin tool confirms parts not available.
Original owner since 6.28.12 mileage currently 41,145 as of 12.21.15. Seat belt front, driver's side slackened and no longer restrains driver.belt will not "lock" when vehicle is in gear.also does not retract any longer, thus making it non-functional.dealer says it will not repair this safety issue, since it was purchased 41 months ago and has 5,100 miles beyond standard warranty.as required safety equipment, and research on internet states, it seems this should be covered for ten years, 100k miles.
Takata recall. The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign numbers: 16v668000 (seat belts, air bags) and 17v640000 (air bags, seats); however, the parts to do the repair were unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The dealer (oliver c joseph chrysler dodge jeep, 3795 il-15, belleville, il 62226) was contacted and confirmed that the parts were not available for the recall remedy. The manufacturer was not contacted. The contact had not experienced a failure. Parts distribution disconnect.
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (seat belts, air bags); however, the part to do the repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The contact inquired about part availability and was informed that owners would receive a second notice when the part becomes available, which may be in june of 2017. The contact had not experienced a failure.
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (seat belts, air bags). The part needed for the repair was not available. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The vehicle was taken to paulding chrysler dealer (located on 1246 old griffin rd, dallas, ga 30157), but the part was not available for the repair. The technician at paulding chrysler informed the contact that there was no remedy and to wait for a second recall notice. The manufacturer was made aware of the issue. The contact had not experienced a failure. Vin tool confirms parts not available.
The contact owns a 2012 chrysler 200. The contact stated that the recall notice for nhtsa campaign number: 16v668000 (air bags, seat belts) was received in september of 2016. After contacting nhtsa, the contact was informed that the parts needed for the recall remedy were not available and no estimated time for receiving the parts could be provided. The dealer and manufacturer were not notified. The contact had not experienced a failure. Vin tool confirms parts not available.
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (seat belts, air bags); however, the parts to do the repair were unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The local dealer and manufacturer were not contacted. The contact stated that he was informed a year ago that he would be contacted when parts became available and that owners would receive a second notice in august 20017 when remedy parts became available. The contact had not experienced a failure. Vin tool confirms parts not available.
2012 chrysler 200 .consumer writes in regards to a defective passenger seat belt.the consumer stated she un-buckled the seat belt, the buckle itself came back and hit her on the right elbow, causing extreme pain. That pain followed up her arm causing numbness and tingling in her last two fingers on her right hand.after a follow-up with an orthopedic surgeon, it was determined the consumer had cubital tunnel syndrome caused by an ulnar nerve entrapment from the seat belt buckle hitting her right elbow. The consumer stated surgery was needed to relieve the pressure on the ulnar nerve.
Passenger head restraint is broken, two little plastic pieces snapped i assume. It happened while i wasn't in the car, parked outside my house. Never had an accident nor have i damaged the car in anyway,
The head rest is detached from the seat and is very unsafe
The contact owns a 2012 chrysler 200. The contact received notifications for nhtsa campaign numbers: 16v668000 (seat belts, air bags) and 17v640000 (seats, air bags); however, the parts needed for the repairs were not available. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repairs. The vehicle was taken to roberson motors (3100 ryan dr. Se, salem, or 97301, (503) 363-4117), but the parts were not available for the repair. The manufacturer was not contacted. The contact had not experienced a failure. Parts distribution disconnect.
Chrysler 200 2012 has issue with headrest assembly on driver side. I had it diagnosed from chrysler dealership. I also read recalls regarding this issue in same cars but when i put my car's vin # to check any recall it says 0 recall. Can you help to see if this can be fixed. It is a driving safety issue.
The contact owns a 2012 chrysler 200. The contact stated that within two weeks of owning the vehicle, the head rest restraint deployed without warning. The vehicle was included in nhtsa campaign numbers: 13v282000 (electrical system, air bags), 16v668000 (seat belts, air bags), and 17v640000 (seats, air bags). The dealer (autonation usa corpus christi, 3115 s padre island dr, corpus christi, tx 78415-1815, 361-217-6733) was notified of the failure. The vehicle was not repaired. The manufacturer was notified of the failure. The approximate failure mileage was 52,000.
Both of my headrests popped open for no reason. The passenger headrest happened two years ago and the drivers seat headrest happened this week. The vehicle was not involved in any type of collision or impact when the headrests popped open. I was driving smoothly on the road when they happened.*dt
Purchased new from chrysler dealers lot in april 2012. When cleaning back seats with vacuum noticed frayed fabric on the seats were the stitching is, as if the stitches had severed the fabric and in just about every stitch on every seat same thing took it in to the dealership to have it assessed and was told they would contact chrysler and call me. I had to take the car back in for photos to be taken and it turned out they were not adequate (black interior) so i waited and waited and called to see what the hold up was and was told chrysler needed better pictures.went back to dealership and showed them exactly what the issue was and pushed on the seat to reveal that indeed there was frayed material.chrysler contacted the dealership and told them to get pictures without pushing on the seat, took it in again and had pictures taken and was told in the mean time the dealership was told by chrysler to get a quote from an upholsterer in regards to new front and back seats. I had to call the dealership once again after not hearing from them for an extended amount of time only to be told that chrysler is not going to replace the seats,there is nothing that can be done.
Takata recall. The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign numbers: 16v668000 (seat belts, air bags) and 17v640000 (air bags, seats); however, the parts to do the repair were unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The dealer (oliver c joseph chrysler dodge jeep, 3795 il-15, belleville, il 62226) was contacted and confirmed that the parts were not available for the recall remedy. The manufacturer was not contacted. The contact had not experienced a failure. Parts distribution disconnect.
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 16v668000 (seat belts, air bags); however, the part to do the repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The contact called a local dealer (carl burger chrysler jeep dodge ram world (8355 hercules st, la mesa, ca 91942) and was informed that the part to do the repair was not available. The manufacturer was not made aware of the issue. The contact had not experienced a failure. The vin was not available.
Driver side active head restraint deployed while vehicle was stopped a convenience store, with the engine running, hitting the driver on the back of the head and startling him. Vehicle was not involved in an accident of any kind. Head restraint could not be reset and broken plastic pieces could be seen in headrest.
The contact owns a 2012 chrysler 200. The contact stated that while driving at 55 mph, the head rest exploded and the air bag did not deploy. The contact mentioned that the failure occurred without warning and the vehicle was not involved in a crash. A police report was not filed and there were no injuries reported. The vehicle was taken to the dealer. The technician diagnosed that there were two fractured clamps inside the head rest causing the failure. The vehicle was not repaired. The manufacturer was made aware of the failure. The failure mileage was 48,000.
The contact owns a 2012 chrysler 200. While driving 20 mph, whenever the contact activated the turn signal, the windshield wipers activated. While driving, the driver side headrest popped off. The vehicle was taken to a dealer where it was diagnosed that the headrest needed to be replaced. The turn signal issue could not be diagnosed. The manufacturer was not made aware of the failures. The failure mileage was 38,500.
Both of my headrests popped open for no reason. The passenger headrest happened two years ago and the drivers seat headrest happened this week. The vehicle was not involved in any type of collision or impact when the headrests popped open. I was driving smoothly on the road when they happened.*dt
For weeks now ive been noticing a weird grinding or dry rubbing sound underneath the front end of my chrysler. Checked it out a few times, as though i am not a mechanic i can identify the basics of something not right. However, after my husband and his brother both looking it over on seperate occasions, they have noted a leak under the carriage of the car. Often here recently, the guage senses an over heating of some sort. Since this notice, we have replaced the oil cooler twice in a year; as well as flushed the hoses associated with the coolant reservoir. Fixed temporary but has now already started getting too hot. Which simply tells me that its something further internal thats wrong. I was informed of an engine recall: l33 of my chrysler model. However havent seen one on this website. When driving yesterday, i noticed a light on my cluster that indicated the traction has failed. When i brake, all u hear or feel is a vibration under your feet, up front. I replaced my brake pads all 4, within the past 4 months and theyre now rusted over and u notice a brake fluid leak on the front right side. After a light, the grinding noise, the vibration and the overheating; i am positive that this will eventually cause a car stall or worse a fatal accident. My brakes could eventually fail while driving in traffic, causing a crash. Or my car could just all out stalland the cluster can trip and i could be in harms way if at the time it does this i could be goin 70 on the interstate or in a turninglane in town and without proper fix; it could easily cause a fatal accident and i could be killed or worse my children!
I was driving my car on 295 s yesterday and it lost power and the hot oil light came on and i had to pull over because i was almost hit by an 18 wheeler and sit there for 30 minutes and it states it is a transmission problemand this is the second complaint i have sent to you and i have tried to callbut no one is answering or they hung up on me.05 .
The contact owns a 2012 chrysler 200. The contact stated that while driving at an unknown rate of speed, the traction, brake, and abs warning lights all simultaneously illuminated on the instrument panel. The contact then took the vehicle to an independent mechanic where the vehicle was diagnosed with a defective hydraulic brake module and brake pump. The mechanic called several unknown local dealers and each dealer informed him that the part was discontinued. The manufacturer was not notified of the failure. The vehicle was not repaired. The failure mileage was approximately 149,000.
Replaced disc breaks pads 3 times last year and 2 times this year, the rubber boot inside the break caliber melted and the rear breaks sometimes smokes, now front break pedal goes towards the flow andwith clucking noise, andtbe abs break light is onwhile i was driving..
Vehicle purchase from enterprise car sale, may 3,2013. Mileage 30926. Immediately i started having problems with loud clicking sound in front tires and loud squealing on backup.enterprise agreed to fix the problem once identified. The inspection to tires and brakes was done and dealership stated they could not get vehicle to replicate the noise(lol) . 2nd trip to dealership. Same complaint. Answer- could not get vehicle to duplicate noise. "you must be kidding me. If i can hear it i know you can hear it. So, my suggestion was to roll down the windows, turn off the air conditioner / radio...you cant miss it. Well, the front tires were replaced because it was stated that they were 1/8 inch to large.but nothing done to the brakes. There was still plenty padding .3rd trip to dealership.brakes are now screaming at me!the pads were replaced with differentmaterial. From ceramic to metallic pads.. Two months have gone by and guess what?the noise is back!!!!.im no genius and definitely not a mechanic, but if you keep doing the same thing you will get the same results.how many times does it take to realize that something else is wrong? the question is....what ?i have read "several complaints from different owners with the same issue. So i know there is something wrong . How many complaints does it require before an investigation takes place and a recall is issued because something is wrong here?.i regret not doingthe research on this car because i know for sure that i would not have purchased the vehicle.
The abs and terrain lights stay on, when car reaches 60 mph it pulls.
Was driving car going only 25-30 mph and made an attempt to slow down to a stop which i had plenty of time and space between car in front of me and my front fender to do, as i applied brakes i notice it go all the way to the floor and my car wouldn't stop which soon after having plenty of space to do it led to a rear end collision as my brakes failed to work correctly when applied. I have a police report to verify the incident on 09/27/2016 in appleton, wi. Because i was going at a really slow speed at the time luckily no one was really hurt when this occurred around 10:00 am in an area with little to no traffic at the time, but even know i was only going around 20 when there was an impact my car which was new prior to this accident is now considered under state law in wisconsin a salvage vehicle as repairs exceeded the value at the time of 7000.00
Bought the car new, on day 2 at around 80 miies, the front brake warped thepassenger side front rotor ,car could barely stop.took it to the dealer and was told it was a faulty rotor, dealer replaced at no charge, approx 3 months later the same thing happened, the dealer replaced both front rotors and said that chrysler had a bunch of faulty rotors. Tried to avoid driving the car anywhere that had any large hills or mountains. Moved to florida shortly after the last repair and thought the dealer had actually fixed the problem, but in 2016 i went back to pa. For a vacation and the first time i drove in the mountains, i had the same brake problem, i had to avoid the mountains. Got home, i replaced everything in the front brakes but the master cylinder and abs system., thought this time it had to be fixed. Then in the fall of 2017 we had to evacuate the state of florida due to a hurricane and we went to north carolina to stay for 5 days. The first big hill we encountered on the freeway the same problem happened, the front of the car vibrated badly and the brakes couldn't hold the car back. Still not working properly very worried about the brakes and still have to avoid mountainous areas. Was quoted a price of approx. $750-$800 to fix. Have already spent $350 to fix it.
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 13v282000 (electrical system); however, the part to do the repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. On a separate occasion, when the brakes were applied and the gear was placed into park, the vehicle accelerated through a wall. The air bags deployed. There were no injuries and a police report was filed. The vehicle was towed to the contact's residence and later towed to geico. The front end of the vehicle was replaced. The dealer diagnosed the brakes. The manufacturer was notified. The approximate failure mileage was 51,000.
The brakes have a high pitched squeal either in reverse or forward for the first mile of driving, but on occasion it has happened while driving for a while to.i took to the dealership and they said there is nothing they can do because they are steel brakes with metal on metal and it is normal.they said it replaces the abestoes brakes.i know other people with new cars and do not have this issue.
On april 26, 2012, i purchased a brand new 2012 chrysler from an official chrysler corporation dealership.since then this car has been put in the shop approximately 30 times for from medium to major problems. The 1st major problem was 9/26/212 which was diagnosed as gear-rack and pinon.it has had two lifters(relative to the motor) because of loud tapping.three heater cords; a couple of re-calls;transmissions leaks; internal engine damages; headlamps needed immediate replacements; washer fluid tank leaked and needed immediate replacement; the car horn failed to blow on demand; brakes needed immediate replacements; camshaft, rockers had to be replaced twice; heater cord experienced internal failure and had tobe replaced; brake pads; brake light (dashboard) has been beeping on since 2013 and is still doing the same thing today; engine air filter had to be replaced; and a host of other vehicle problems that should not be happening on a brand spanking new 2012 vehicle!!please assist and advise.
The contact owns a 2012 chrysler 200. While driving at 45 mph, the brake pedal was depressed and the contact felt the pedal vibrate. The vehicle was taken to an independent mechanic who diagnosed that the brake pads needed to be replaced and the rotors needed to be turned. The vehicle was repaired. The manufacturer was not notified of the failure. The failure mileage was 66,000.
Every time you reverse back-up the car you will hear a loud piercing horrendous and annoying sound.
Driving vehicle to investigate symptoms and during regular casual driving the car stalled, hydraulic brakes went and steering locked while slowing through a school zone. I'm a certified tech with h-d, kawasaki, bmw, and have never had a service manager deny a request that involved serious systems like this until today. That is why i'm filing this complaint on your site, i was told by the s.m. That they couldn't get my 29 day old 200 in before next week monday! this is not a safe car, anyone reading this please do not buy this car!!!! mdm.
I have to replace my brakes every 2 to 3 months and it has become very costly for me. I have to replace my rotators twice a year.
Front brake rotor keeps warping and brakes do not work well until rotor is replaced. Car was like this from day 1, dealer said it was fixed 3 times but it wasn't. I have replaced all front brake parts myself 2 times, and it is still bad. Cannot drive the vehicle anywhere if the roadway is in a mountainous area.05
When in reverse brakes squeal, under any conditions. Took to dealer, was told by dealer that all cars do this when backing. Smh
Takata recall, abs and traction light are on they make a funny noise when i first start the car and start driving. But after i go so far or to 25mph, my lights come on and i brake just fine. I also have a issue with my turn signals, if my headlights are off my front left turning sognal works but if my headlights are on my front left turning signal does not work.
Within 2 days of purchasing this vehicle, rear brakes were squealing like they would do if they were due to be replaced.i brought it back to the dealership and they supposedly inspected them and told me "its just rust from sitting on the lot and it will clear up after you drive it a while", it continued and a couple months following the first visit i returned with the vehicle and told them it still was making the noise and they checked it out again and said "oh, its just dust on the brakes and if you step on your brakes hard at about 40 mph that should take care of the problem".here we are 2 years later and the rear brakes still make the squealing noise.about june/july of this year timeframe i brought my vehicle in to the dealership because i have about 5 different spots on the hood and grill of the vehicle has the paint "blistering" and rust underneath.the dealership didn't call me and tell me what they were going to do about it so i called them about a month later.the warranty guy at the dealership told me that chrysler was going to "send a whole new hood" which i guess didn't make much sense to me but whatever.to date i haven't heard from the dealership any further on this matter and the vehicle is nearing the limits on the warranty period for mileage.the dealership i have been dealing with is john hirsch's motors in cambridge, mn.
The contact owns a 2012 chrysler 200. The contact stated that the abs warning light illuminated as the front end exhibited a loud metallic noise. The vehicle was taken to the dealer where a diagnostic was performed, which located the failure at the driver's side front wheel bearing. In addition, the abs system was faulty. The dealer disconnected the abs system. The driver's side front wheel bearing was not repaired. The contact also wanted to add that the water pump was replaced due to loud noises that were emitted while driving. The failure mileage was 17,000 and the approximate current mileage was 21,000.
I have made several complaints to chrysler regarding the vehicle not accelerating when it should and not going over 35mph at times.when the vehicle won't accelerate the 6 speed does not work either.chrysler reset the computer and this worked as a fix for roughly 2 days until it happened again.the vehicle also jumps forward when braking and seems to be jumping very hard through the gears,chrysler has responded every time that they cannot duplicate the problem and to bring it back when it happens again. Today i was driving to work and again the car was jumping when i was braking.the car in front of me braked hard and unexpectedly therefore i had to as well.my car did not stop! although the brake pedal was pushed as hard as i could the car jumped at least 6 times and made a horrible grinding noise before i finally was able to get it to stop before rear ending the car in front of me.i did make it in to work however, the car did not make any improvements after this, now every time i try to stop the car jumps forward.this car is going to get me, my kids or someone else seriously injured and chrysler has no sense of urgency to seem to get it fixed.from what i have read it is not only my car that is having the same problem.add it to the lists of recalls please!!!!! also when i am driving and this happens daily the car jerks very hard between 1st and 2nd gear, this literally causes the car to and feels like it may stall out.
Our airbag lights are on. We got notified by the dealership of the recall. But this matter regarding the wheel bearings is a serious matter. I've repaired my car 5 times all around the car. That's not normal. All of these vehicles have a similar issue in the rear end where when i'm driving and hit a bump, the rear end shifts left or right.
This chrysler 2012 200 started to have brake squealing issues at about 7,000 miles i went to dealership and they told me that it was probably just being broke in since i purchased this car at 200 miles on it.the problem continued and no one at the dealership would address this problem.i then told them they had to do something about it and they then told me that there was not a fix for this that chrysler could not fix this problem.and that they the dealership dennis dillon and chrysler had no idea what to do.i continued to drive my car and in september of 2013 my car's check engine light came on and i took into the dealer dennis dillon and was advised that my cylander head was gone and would need repaired. I was told to go ahead and dive my car while the parts came in.my car was fixed and picked up from dealer then 1 day later my car overheated on interstate and broke down was then told a clamp came off and was then fixed.since this issue my car has not driven the same. It is sluggish . I asked the dealer about the lemon law and was told to contact chrysler . I did so and was told by chrysler that there is nothing anyone can do. My brakes still sqeal very loudly and chrylser told me that its becasue they replaced the brake pads and no longer have asbestos' in them.i then advised them that i have driven other models and makes and did not have that problem.they refused to be of any assistance. My steering is also an issue in which the dealership has said that it needed an alignment but since the car was only a couple hundred miles on it.it has pulled severly to the left. This is not acceptable and this car needs to fall under the lemon law and be dealt with.
Break light in dash comes on and off constantly
Was at a stop light and after taking off the car shut completely down with no warning no engine light indicator until after this happened. I tried to start it and it cranked but didn't start all the way, i had it towed home andnow it starts. I had a six month old infant in the car with me when this happened and i don't feel safe when the car can just shut down like that. I feel there is a default in the engine, we purchase this car a year ago. Thank god there was no one behind me when this happened.i also have had problems with the brakes from when we purchased the car i brought the car to the dealer four times before someone figured it out. It was fine for four weeks and the noise is back, there is a noise in the brakes only when you press the brakes lightly. This problem has not been resolved. And the the warranty is up. I feel it's a defect. Upon my last visit to chrysler there was a customer there who also has a 200 with the same brake problem they were trying to resolve.
Mold inside passenger door and back left side door, every time it rains, water collects in the door and never comes out - causing mold to form. Car has never been wrecked and it was bought brand new
When i brake on bumpy road the car drifts to a stop instead of coming to a stop
The contact owns a 2012 chrysler 200. The contact stated that while driving at 70 mph, the headlights failed without warning. The contact also stated that the traction control, the cruise control and the abs warning lights were illuminated. The contact also stated that there was a grinding noise coming from the front of the vehicle. The vehicle was not taken to be diagnosed or repaired. The manufacturer was notified of the failure. The approximate failure mileage was 112,000.
2012 chrysler 200 shut off while driving 45 mph down the hwy with 2 children in the car. I lost power steering and my brakes. Luckily, i made it to the side of the road. It restarted once i turned the key to off first, but shut off on me a second time while idling a few minutes later. I have not driven it since.
"takada recall" while driving down the road at 40 mph. I heard a chime and looked down at my instrument panel. The abs and the electronic stability control was on. Light was on for both. But instead of the esc it was the little car with wavy,jiggly lines under it. These two lights have been on constant for a good 3 weeks. It has gone out while driving a few times for a few minutes just to come back on and stay on almost all the time. There is no flashing of the lights. I don't drive every day. I drive around 5 times a week and short distances of 2 to 4 miles for the most part. There is also a whistling nice coming from the front of the vehicle. I don't think it is very safe to drive since the brakes and traction of the car are all to important part of me and my families safety. Please help with this issue. I paid and am still paying a lot for this car that now has 62000. Miles on it.
To start off the abs and traction control will not stop turning off and on even after replacing everything . Almost all the time when it rains they will kick in the e brake and start grinding . No matter how many times i change the brakes and rotors and master control they never stop squeaking . Lastly almost all the electrical problems started after the alternator failed and i had to replace it . My speedometer just died on me today and i have no clue how that happened .
This vehicle out of service .could of cause a collision or cause body injury or death ,i started the car went about 100 feet or more, car made a loud noise ,car stopped suddenly by itself, then brake part flew right off right on the road. Had to push car to the nearest corner.called dealer service, called my insurance.i have full coverage, but no response at the time. I signed hardship packet from the bank for help, but was repossessed, so dealer could not pick the car .i made a complaint february 12,2013 to bakersfield chrysler - jeep about my brakes squeals and my tires always display low pressure. Service dealer said there is nothing to fix they squeal because of dirt and they are wet and tires need more air because of weather change. I brought this car brand new. I sent a formal written letter addressed to nhtsa, plus documentsthat will substantiate my situation.updated 03/13/14
When slowing down almost to a stop, the vehicle downshifts hard. It cause a shutter or jerk and you can feel even in the brakes. Feels awful and cannot be normal. Also, when accelerating, the vehicle pulls hard to the right.
When driving the vehicle will suddenly shut off. No warning of it about to happen just does. I lose steering and brakes and turns on only after time goes by or by removing negative terminal from battery. It's happened at 35mph and at 60 mph. I've gone a week with no incident to having it happen dozens of times on a single trip. Very scary situation. Especially in traffic.
When backing up from a parking place the first time it happened in the latter part of april 2013, we heard this loud screeching noise coming from what we thought to be the front wheels . I then took the car to the dealership told the service person about it, he then said all cars have been doing it because of the dust storms in the area . The noise has been getting louder and louder it's embarrassing any more to back up ! who would think such a nice and beautiful car would be emitting such a terrible noise. Even my elderly dad has noticed it every time i pick him up and he said what a shame it is that this car makes that horrific sound . On 10-22-13 i reported this problem again our car dealership and asked them to start a case about it and i'd report it to nhtsa. The service manager agrees with me and stated there is a problem with the chrysler 200 cars and that chrysler corp, refuses to admitthere is problem with these cars! don"t buy this car!
After putting on 4 new tires and new front brakes, we noticed an issue with the steering column clunking, and feeling very loose. After three trips to the service counter at a chrysler dealership, (you would think that they would know what the problem was), i have figured out the issue thanks to youtube. Apparently, i there are many others having the same issue. And, i called chrysler directly, and the girl that i spoke with stated that the part had been recalled on other chrysler products, but not on my car. This part needs to be recalled. You feel like you are driving down the road, and the car is falling a part. You feel like parts could fly off at any time. Very disappointing! and, just out of warranty. Please view this website to understand the issue. It explains it in depth.https://www.youtube.com/results?search_query=chrysler+200+clunking+problem.
Transmission rebuild and three torque convertors in 6 moheater warm on left cool on rightengine stalls on highwayheat worked when taken to draler.they replaced sa clicking blend door actuatorin the morning there was warm air on the left and cool air on the right'dealer says need a heater core and radiator.this happened overnight?recall onairbags.no airbag light on at dealer,they flashed the tipm as per recall,now airbag light is on code reads replace occupant controle module.they claim this not on the recall,11v315000
I purchased a 2012 chrysler 200 from carmax located in memphis tennesse back in july 6, 2015. After a few days of purchase i noticed the brakes were not working properly. I took the car back in immediately for service and the service manager advised it was just a small problem and assured me that it was fixed. In august i had the same problem and took it back to the service department ( please be advised i am employed and i have to drive from pine bluff to memphis) at that time the service manager advised that it was some kind of fluid and the problem was fixed. This was all done during the factory warranty. On november 8, 2015 my brakes began to drag and was barely stopping i took it back to the service department and demanded for the problem to be fixed back to factory profection. Mr. Joe brown advised that it would be covered under my warranty but i advised that the car was never repaired correctly under factory warrenty. I had to pay a 50.00 dollar deductible and fifty towards a rental car deposit. I was called on 11/13/2015 and adivsed that my car was ready. I couldn't pick the car up until saturday morning 11/14/2015. When i came to retreve my car my car was just sitting in the parking lot and no service worker was there to drive the car with me to ensure that it was working properly. In conclusion my brakes are still not working and it could have caused me my life on this morning 11/17/2015. The brakes are worse.i am in tears because i am a recent graduate and i am working to pay bills and student loans. This is what place american people in proverty when someone sales you something and it only works for a short period and you pay for warrenty and that doesnt help neither. Please help.
In traffic, steering wheel tightened up and all interior lights were off. Tried to brake but no response, shifted into neutral restarted the car and it turned back on. Seemed to mess up the shifter a little in the process, as well as almost hitting the car in front of me. Probably going about 10-15 mph, and i was lucky to throw the car in neutral and restart otherwise i would of floated into an accident.
My abs light has turned on.and my abs isn't working.also my radio also is only working intermittently.
I was driving at normal condition at 35 miles per hour, at one time, the abs and esc light come on thedashboard, there is no rain no snow, no excessivebraking or speedingor turning, since 4 days passed,the lights come on every day when engine running.updated 11/04/15
In traffic, steering wheel tightened up and all interior lights were off. Tried to brake but no response, shifted into neutral restarted the car and it turned back on. Seemed to mess up the shifter a little in the process, as well as almost hitting the car in front of me. Probably going about 10-15 mph, and i was lucky to throw the car in neutral and restart otherwise i would of floated into an accident.
The contact owns a 2012 chrysler 200. While making a turn, the contact heard an abnormal grinding sound coming from the power steering without warning. The contact stated that the failure recurred several other times. The vehicle was not diagnosed or repaired. The manufacturer was made aware of the failure. The failure mileage was 29,000....updated 05/17/17 the consumer stated the vehicle was repaired by the dealer on 3/31/2017 at the owner's expense. The consumer believed at 32,256 miles, the failure was premature. Updated 09/06/2017
Car started kicking back, had to accelerate to stop the kicking.then while parking the steering wheel locked up and engine died.kept starting and it kept stalling.
The contact owns a 2012 chrysler 200. The contact stated that when driving between 16-22 mph, the vehicle would hesitate. The vehicle was taken to the dealer for inspection where they stated that the vehicle was changing gears as it was designed. The vehicle was not repaired. The contact also stated that the steering wheel seized without warning. The manufacturer was notified and stated that there were no recalls on the vehicle. The failure mileage was 2,000. The consumer stated the very day they picked the vehicle up, it stalled in the entrance way. The dealer claimed, the vehicle ran out of gas. As her son drove the vehicle home, he noticed when coasting at low speeds, the vehicle would kick back. The mechanic stated the jerk/kick was from the engine shifting gears. The kicking would go away, when the accelerator pedal was pressed.when her son turned the steering wheel to the right and then straightened it out, by turning the wheel to the left, the steering wheel locked up.he put the vehicle in park and shut off the engine. He tried to re-start the vehicle several times, but the engine would rev up tight until it was about to start, but would immediately shut off.the vehicle was towed to the dealer, where they found a code, but it had nothing to with the problem, that was being experienced. Updated 01/16/13
Clunking popping in frontend you can feel it in steering wheel. Car was under warranty when this started dealership couldn't duplicate the problem it continues to get louder and many people with this car have this same problem.
Sudden stall on the highway, completely died on the slop of the beginning of the bridge on april 4,2019 and april 11, 2019
While returning to airport for return trip home, was in the 2012 chrysler 200 rental car.slowed down to go into a curve and when came out of curve it was like the vehicle was sucked off the road to the right.had no choice---that is where the car was going...my passenger and i were airlifted to hospital.i suffered from 3 back fractures, 3 rib fractures, fractured sternum, contusions to the lungs and 26 stitches in the forehead.was in hospital for a week and out of work for about 2 months. Passenger had 2 back fractures, rib fractures also.i have asked avis/budget to get this car out of their fleet before someone gets killed.chrysler needs to recall this car.they had steering recalls on the 2011 model.
2012 chrysler 200 shut off while driving 45 mph down the hwy with 2 children in the car. I lost power steering and my brakes. Luckily, i made it to the side of the road. It restarted once i turned the key to off first, but shut off on me a second time while idling a few minutes later. I have not driven it since.
When slowing down almost to a stop, the vehicle downshifts hard. It cause a shutter or jerk and you can feel even in the brakes. Feels awful and cannot be normal. Also, when accelerating, the vehicle pulls hard to the right.
I rented this vehicle from enterprise in henderson nc.while traveling to nashville, tn., i noticed that the car often lost handling capacity when coming off small bridges as there is often a small drop off.this happened at least 7 times as i decided to slow down to 55 (limit is 65) whenever crossing them.this is quite a surprise and i had this experience only once before and it was on a very small vehicle some 10 years ago.it was noticeable to the point that my passenger felt it as well and i would have had a wreck had i snatched the wheel during these scenarios.to be more clear, after crossing thesmall bridges...maybe 20 yards long on average, there is a drop off to the normal highway and the front end does not transition down, it actually takes on air before doing so and that is where the loss of control comes in.i would hope this can be tested and corrected before an owner loses his/her life.
The contact owns a 2012 chrysler 200. While driving 35 mph the steering wheel ceased and the vehicle stalled. The contact was able to restart the vehicle after five minutes. While driving and making a left turn the vehicle stalled again. While attempting to start vehicle there was abnormal ticking noise detected. The abs and traction control warning lights were illuminated. Additionally, the speedometer was inoperable. The local dealer was not contacted. The manufacturer was contacted but no further assistance was provided. The failure mileage was 114,000.
Driving vehicle to investigate symptoms and during regular casual driving the car stalled, hydraulic brakes went and steering locked while slowing through a school zone. I'm a certified tech with h-d, kawasaki, bmw, and have never had a service manager deny a request that involved serious systems like this until today. That is why i'm filing this complaint on your site, i was told by the s.m. That they couldn't get my 29 day old 200 in before next week monday! this is not a safe car, anyone reading this please do not buy this car!!!! mdm.
I was driving my new chrysler 2003.6l approximately 25-30 mph pressed the gas pedal and had no response.engine was dead, the steering locked-up causing the vehicle to pull right running off the road.fortunately, my two children and myself were not harmed.i am extremely disappointed/angry that my children were put into this situation.i believe this is a an unsafe vehicle and investigation should take place.
To start off the abs and traction control will not stop turning off and on even after replacing everything . Almost all the time when it rains they will kick in the e brake and start grinding . No matter how many times i change the brakes and rotors and master control they never stop squeaking . Lastly almost all the electrical problems started after the alternator failed and i had to replace it . My speedometer just died on me today and i have no clue how that happened .
This is frustrating.i've been to two dealerships complaining about the rattling steering column.both dealerships state that they could not find the problem.went to brakemasters for an oil change and the mechanic said the rattling is coming from the steering column. Both times at the dealerships the vehicle was still under warranty.i'm over the 3 year mark now and no warranty. What can be done?
Our airbag lights are on. We got notified by the dealership of the recall. But this matter regarding the wheel bearings is a serious matter. I've repaired my car 5 times all around the car. That's not normal. All of these vehicles have a similar issue in the rear end where when i'm driving and hit a bump, the rear end shifts left or right.
Drove approximately 0.5 miles when the engine started to kick back, drove another 0.5 miles and as i was parking the car the steering wheel locked up.put the car into park and turned off the engine.the car would no longer start as the engine would rev right up until the engine should flip over but the car just shuts down at that point.waiting for a tow at this point to the nearest dealership.
When driving the vehicle will suddenly shut off. No warning of it about to happen just does. I lose steering and brakes and turns on only after time goes by or by removing negative terminal from battery. It's happened at 35mph and at 60 mph. I've gone a week with no incident to having it happen dozens of times on a single trip. Very scary situation. Especially in traffic.
Power steering or steering assist does not always work
Submitted a complaintwhere i inadvertently listed my vehicle as a 2015 chrysler 200.my car is a 2012 chrysler 200.could you change my previous complaint of this same date to reflect a 2012 chrysler 200.
It has been increasingly difficult to see at night when driving my chrysler 200 2012 in low lit areas due to the headlight beams.less light? aimed low?i have to drive far slower than posted around bends at night. I don't recall this issue when i bought the car brand new.i have had it one year and have just over 10,000 miles.i don't usually have to drive at night other than my well lit neighborhood ,so this could have easily gone unnoticed.either way, this terrifies me.the other issue i have is a jerk when shifting to reverse or drive. It is a loud clunk and i feel the vibration. I will not drive at night in low light areas until resolved.i also feel the car pulls to the right when driving. I will contact the dealer soon, until then i just don't feel safe driving while on dark roads.
Van horn chrysler and dodge in plymouth wi. Sold me a vehicle that was in a major front end accident. When they sold me the air the airbag was not attached. The steering was pulling to the right. The suspension was severely damage, it was so severe that when i took the car to chrysler, i spend money there to get the problems repaired. Because van horn wouldn't pay for the repairs. After chrysler couldn't make the repairs, because the car had been in a major accident from the previous owner. Chrysler referred me to the body shop, where i was out of pocket for another additional repair.i also forward this information to chrysler customer assistant1-888-992-1997. My case number there is [xxx].they (chrysler customer assistant) said the car should have never been sold. They informed [xxx] manger to get in touch with me to make a settle. Which he hasn't as to 10/14/205. Tom boweo was the person that i spoke with at milosch's palace collision center, lake orion mi. (248)276-6653. The car is registered to [xxx]. My email address is[xxx]. My phone number is [xxx]. My cell number is [xxx]information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6).
After driving for 15 or 20 minutes or more, i can hear and feel in the steering wheel a clunking noise/sound under the hood. There is no pattern to it. It happens either on a straight line or by turning. The banging rate won't increase/decrease if i speed up/down. If i turn on the ac before the clunking noise/sound starts, it will commence to make the noise/sound before the 15 or 20 minutes of driving. It is driving me crazy (no pun intended). It sounds like something is completely loose and is going to fall at any moment. My safety and those riding with me are not secured in this car. The internet is full of people with this same problem for this particular car and there is not one solid solution for it. Could anyone help us and make chrysler get more serious with this problem/solution?regards.
The vehicle stalls out - power is shut-off without any notice.the vehicle becomes tdisable while trying to drive.this occurs three times this year.the only way to get the vehicle operating again it to put in park and restart the car.the steering while locks up as well.i have to take the highway to work everyday.most of the instances when this happens i'm not driving on the highway.the stalling of the car occurs when you drive about 2-3 miles.the car bears left and starts to stalled out.it lost power.every time this problem occurred it happens while the car is in motion.
This chrysler 2012 200 started to have brake squealing issues at about 7,000 miles i went to dealership and they told me that it was probably just being broke in since i purchased this car at 200 miles on it.the problem continued and no one at the dealership would address this problem.i then told them they had to do something about it and they then told me that there was not a fix for this that chrysler could not fix this problem.and that they the dealership dennis dillon and chrysler had no idea what to do.i continued to drive my car and in september of 2013 my car's check engine light came on and i took into the dealer dennis dillon and was advised that my cylander head was gone and would need repaired. I was told to go ahead and dive my car while the parts came in.my car was fixed and picked up from dealer then 1 day later my car overheated on interstate and broke down was then told a clamp came off and was then fixed.since this issue my car has not driven the same. It is sluggish . I asked the dealer about the lemon law and was told to contact chrysler . I did so and was told by chrysler that there is nothing anyone can do. My brakes still sqeal very loudly and chrylser told me that its becasue they replaced the brake pads and no longer have asbestos' in them.i then advised them that i have driven other models and makes and did not have that problem.they refused to be of any assistance. My steering is also an issue in which the dealership has said that it needed an alignment but since the car was only a couple hundred miles on it.it has pulled severly to the left. This is not acceptable and this car needs to fall under the lemon law and be dealt with.
Steeringwheelmakes a poppingsqueakynoise with only 29000 miles, is somethingloose ?
My 2012 chrysler 200 s stalled on a major highway. After coming to a complete stop due to traffic the vehicle would not accelerate, the steering locked up and then it shut off. There were no malfunction lights or any other type of warning called chrysler and they said that there are no recalls for this despite there being a number of complaints reported.
While driving, the car began to rapidly lose functionality while warning lights were appearing on the dashboard until it abruptly shut down while driving in traffic. The time from no warning lights to complete loss of functionality was approximately 10-15 seconds. The shut down included an abrupt loss of power steering and braking capabilities while driving on a busy street at night. I was able to quickly compensate for the loss of power steering and braking and stop the vehicle while avoiding a crash, but just barely. Thankfully, i broke down next to two police officers who helped push my vehicle onto the side of the road. These officers may be able to attest to the fact that no noises or abnormal operation of the vehicle was apparent before the abrupt shut-off while driving. Attempts to restart the vehicle involved no clicking or the engine attempting to turn over. The vehicle is currently being repaired, but the preliminary diagnosis is one of a faulty alternator. I will attempt to retain the faulty alternator from the repair center. I had only started the car 2-3 minutes before the incident and there were no apparent electrical issues (engine struggling to start, lights dimming, etc.) while starting the car or during operation.
After driving for about 15 min. You can start hearing a clunking noise coming from the left side, and you can feel it in the steering wheel.don't know if its steering or suspension, but i get eerie feeling the car may lock up.
The contact owns a 2012 chrysler 200. The contact stated that while driving 20 mph, the steering wheel became difficult to turn. The vehicle was taken to the dealer for inspection where they stated that there was no power steering fluid in the vehicle. The vehicle was replenished with power steering fluid but the failure recurred. The also contact stated that the power steering hose exploded and needed to be replaced. The vehicle was repaired. The manufacturer was not notified. The failure mileage was 6,047. The consumer stated there were numerous problems with the vehicle, such as a coolant leak, oil leak, air condition, the cd player did not work, the power steering hose burst, the wire harness, the transmission was replaced, the engine was noisy and the seat belt on the passenger side was not properly installed.the vehicle cut off several times. Updated 10/31/13
After putting on 4 new tires and new front brakes, we noticed an issue with the steering column clunking, and feeling very loose. After three trips to the service counter at a chrysler dealership, (you would think that they would know what the problem was), i have figured out the issue thanks to youtube. Apparently, i there are many others having the same issue. And, i called chrysler directly, and the girl that i spoke with stated that the part had been recalled on other chrysler products, but not on my car. This part needs to be recalled. You feel like you are driving down the road, and the car is falling a part. You feel like parts could fly off at any time. Very disappointing! and, just out of warranty. Please view this website to understand the issue. It explains it in depth.https://www.youtube.com/results?search_query=chrysler+200+clunking+problem.
The contact owns a 2012 chrysler 200. The contact stated that while parked, she noticed an abnormal grinding sound. The contact inspected the engine compartment and noticed that the power steering fluid was low. The contact added power steering fluid however, the following day the contact noticed the power steering fluid was low once again. The manufacturer was not made aware of the failure. The vehicle was not repaired. The approximate failure mileage was 38,100.
Car dies for no apparent reason and during any type driving.of course, when motor dies power steering is lost.extremely dangerous in the heavy austin traffic that i drive in.may just shut down on a major overpass with no where to go.this vehicle puts my life and families life in danger.this shut down can happen at 10 mph or at 60 mph or above.i try to bypass major highways in austin even though it may be several miles out of the way, and so far have been able to avoid any problems.it seems ridiculous to have to travel like this.my car engine is a 2.4l and i know there has been a recall on chrysler's 3.6 l engine in the 200, but i believe this engine needs to also be recalled
The contact owns a 2012 chrysler 200. The contact stated that when the vehicle accelerated and pressure was released from the steering wheel, the vehicle veered sharply to the right. The failure recurred numerous times. The vehicle was taken to the dealer for diagnosis but the contact was told that was how the vehicle was designed. The manufacturer was notified but offered no assistance. The failure mileage was 1,700 and the current mileage was 3,000. Updated 09/21/12*ljupdated 09/24/2012
My car received a software update for the pcm on 3/2/2017. On 03/6/2017 my car shut off completely in the middle of driving down the interstate.
While driving my vehicle back the office from my lunch break, i made a right hand turn onto the main road and began to accelerate the vehicle with more gas.at about 35mph the car engine completely shut off and i had to coast to the side of the road with no power steering.i had to wait approximately 20 mins until my car would restart again.i was able to get back on the road until after another few hundred yards of driving the car stalled again completely.i was then forced to call a tow truck to have it taken to an auto shop.
Awful popping noise to front end when driving. Worsens over time . Had to shop 4 times. They now admit to a problem with tie rods at manufacture. Dealership is offering to fix with a $100 co-pay since it is now out of warranty mileage. I am working with chrysler to get the rest covered since it is an unresolved warranty issue.
A clicking noise in steering wheel while driving no matter how fast you are going. Also, a knocking noise when driving over bumps. Sometimes, the car does not pick up speed for a while when driving up a hill.
The steering wheel vibrates and there is a clunking noise made that sounds like it is coming from the steering wheel column when driving.it occurs at any speed.it feels like the steering column is loose to a point.
The contact owns a 2012 chrysler 200. The contact stated that while driving approximately 25 mph in rainy weather, the rear end of the vehicle began to skid. The vehicle was taken to an independent mechanic where both rear tires were replaced. The failure recurred whenever the vehicle was driven on wet road surfaces at any given speed. The vehicle was also taken to an authorized dealer where a rear end wheel alignment was performed and the tow was replaced. The failure persisted and the vehicle was not further repaired. The manufacturer was notified of the defect. The approximate failure mileage was 24,000.
Purchased this vehicle new off the lot april 2012.this issue i currently have became an issue for me in feb 2014 with the winter weather i entered freeway tried to gain speed once speedometer hit 50ish noticed thecar began to brake loose and sway side to side really quick and scary,immediately slowed down sensation went away could not drive above 40mph, while all traffic around me on the freeway were traveling at a much greater speeds i figured it was just by chance i hit an ice patch.i attempted to speed up and once hit 45mph the side to side sway once again was present exited the freeway and do not travel above 40 in any wet,snow,icy weather but regardless of speed if i hit anything slick i sway, the low speeds just help me maintain control of the car.my husband thought i must just need a winter tire,(there are a set of 4 goodyear eagles on it presently) until he drove it and determined there was definitely a serious issue jacked it up to reveal that it was theinner tie rods completely wiped out contributing to the sway.contacted the dealership to resolve it(mind you the mileage was now at 37050) was told they would do an inspection for $85 and would call chrysler to see if they would honor a repair since it is out of warranty however no guarantee that the repairs would be covered non the less a front end alignment.i could not leave my car for 3 days for diagnosis nor afford 85$ that would not even go towards the repair.i called chrysler only to be told they can not guarantee anything nor would chrysler consider anything until i have an inspection done that there are no discounts no courtesy inspection to be had.bought a new car to avoid issues such as these.
The contact owns a 2012 chrysler 200. The contact stated that while driving 35 mph in the snow, the vehicle would sway to the left and right. The contact stated that he decelerated and the swaying stopped. The vehicle was not taken to the dealer for inspection. The vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was 60,000... Updated 03/24/14
The steering column makes loud "popping" noises at low speeds and when turning the vehicle.it sounds like the steering column is going to snap.in addition, i had to have all of my lifters replaced in the engine due to a loud ticking noise coming from under the hood.lastly, the leather material is coming off of all of the doors in the vehicle, and the light for the emergency brake stays on even when the brake is not engaged.i despise driving the car and will never buy another chrysler.
My chrysler 200 was purchased about two months ago since i purchased it from florida and i reside in alabama i was told by the local dealership in mobile that they could not diagnose or repair it because they have no history. My car is randomly stalling and loosing all power to engine when attempting to stop or slow down there is no codes on dashboard. Pcm was replaced still same issue. It is very likely this will cause an accident especially because there is no warning. It cut off tonight on my way home from work while i was driving at 35mph. This is dangerous
The chrysler 200 vehicle that i purchased in april 2012 was brought in again on 7/1/13 for service due to front end clanging metal noises which occur while turning, backing up, slowing and stopping. This undiagnosed noise began following several engine stalling episodes, two of which required towing (since i was unable to restart the vehicle to drive in for service).the engine stalling episodes occurred while driving at 55 mph and as stated, twice resulted in towing and service.service on the engine stalling problem occurred in april and again in may 2013. It is unclear why the remedy for the engine stalling was not followed per the nhtsa recall id # 11v487000 (engine and engine cooling) technical service bulletin/chrysler manufacturer remedy- since that recall had already been published.in addition to this safety issue, the front end metal clanging may be the result of towing due to the engine defect and/or a result of another vehicle defect (recall #11v315000 - steering column). This is a vehicle that has multiple problems and poses a serious safety issue due to various problems.it needs to be off the road.
2012 chrysler 200. Consumer writes in regards to paint bubbling and rust on vehicle. *tgwthe consumer noticed the paint above the passenger side head light was bubbling, indicating rust. He took the vehicle to the dealer for an inspection. The dealer stated it appeared the vehicle had previously been painted. Chrysler instructed the consumer to send pictures of the vehicle. After looking at the pictures, chrysler stated the problem was due to an environmental issue.
Excessive "fish tailing" in minimal snowy conditions, very unstable, absolute death trap. I felt like i was going to end up smashing into a passing car or truck . Drove for 30 miles per hour for 260 miles while there wasn't more than one inch on snow on the ground because the rear end of the car was swing in all directions, my wife and daughter terrified. I just bought the car back in august 2013 thus a few months ago and had no issues driving on dry ground but only in snow and wet conditions.
2012 chrysler 200.consumer writes in regards to rain water back flow into passenger side from clogged tube, customer seeks reimbursement.*ldthe consumer stated the manufacturer provided reimbursement.
The contact owns a 2012 chrysler 200. The contact stated that the front driver side door started to smoke. The contact stated the she attempted to extinguish the fire with water however, she was unable. The fire department was called and extinguished the fire. The contact a disable person, was scared for her safety and the safety of others. The contact called the dealer where she schedule an appointment and later taken the vehicle to lone star chrysler dodge jeep ram dealer, (8811 interstate 35 access rd, san antonio, tx 78211) but was not diagnosed or repaired. The vehicle was not repaired. The contact stated that now the driver side door failed to lock. The manufacturer was made aware of the failure and sent out a third party and the contact was informed that the door was badly burned and there was noting else they could do. The failure mileage was approximately unknown.
Dear sir/ madam:11-08-15a fireoccurred at my house which was located at [xxx], on the above date, i parked my 2012 chrysler 200 in the garage and went to bed. Approximately 45 minutes to 1 hour after retiring, i was awakened by a loud explosion and my neighbors beating on my front door to awaken me and my 21 year old grandson.he also was sleeping in another bedroom. When both of us attempted to escape from the house through the kitchen/garage entrance, we were met my heavy bellowing grey and black smoke that prevented our exit and almost overwhelmed us.several months later, i am yet suffering from the shock and emotional trauma.because of dealing with flashbacks, nightmares, intermittent waves of nervousness, deep sadness, feelings of grief/loss, periodic confusion, digestion issues, and numerous financial concerns, i am in professional counseling.i have been unable to write this letter until now.even now, a friend is assisting me with completing this communication.this is the second contact i have had with your corporation.the first was the morning after the fire, when my son called on my behalf from his cell phone.he was informed that there was no recall of this particular chrysler 200, however there were some known problems with the gas tank and ignition systems that were built between march and november of 2012. Please understand.i lost my house, 23 long years' worth of cherished belongings, and the car i recently purchased. I lost everything in the fire.i decided that,i would rather initially contact chrysler directly.my hope is that chrysler will understand the gravity of the situation and do the right thing without going through expensive attorneys.[xxx]https://onedrive.live.com/redir?resid=cebfb7d86d50e64d!750&authkey=!aalipdbqwpwsze8&ithint=folder%2cinformation redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6).
Can see bubbling thru paint on engine hood took to dealer was told aluminum hood is corroding
I was traveling 55 mph on the highway my tire blew out an the fender blew off but somehow the cars whole engine wiring system was ripped out of the car in which the whole car went completely dead of all electricity thankfully i was able to pull on shoulder of highway before the car stopped rolling.
Was driving car going only 25-30 mph and made an attempt to slow down to a stop which i had plenty of time and space between car in front of me and my front fender to do, as i applied brakes i notice it go all the way to the floor and my car wouldn't stop which soon after having plenty of space to do it led to a rear end collision as my brakes failed to work correctly when applied. I have a police report to verify the incident on 09/27/2016 in appleton, wi. Because i was going at a really slow speed at the time luckily no one was really hurt when this occurred around 10:00 am in an area with little to no traffic at the time, but even know i was only going around 20 when there was an impact my car which was new prior to this accident is now considered under state law in wisconsin a salvage vehicle as repairs exceeded the value at the time of 7000.00
Mold inside passenger door and back left side door, every time it rains, water collects in the door and never comes out - causing mold to form. Car has never been wrecked and it was bought brand new
.there are about 8 cars ahead of me in my lane as we wait for the green light. When the lights turn green i note that my lane hasn't moved and the buses are steady chugging through the intersection in the left lanei look into my rearview mirror, i was the last car in line for this stop and i hadn't even gotten my foot off the brake andall i could see was a big black grill coming toward me. I braced my hands on the steering wheel and shoutedplease don't hit me'before i could finish the sentence blam!'fortunately the cars ahead of me were just starting to move forward.my head snapped so hard my ears went full.the dash mat on my car came at me like an airbag. My phone in the front center console flew forward and hit the shift knob and the back popped off and must have shaken the battery loose. The coffee in my lidded cup spewed out thru the small sipping hole all over the corner of my leather seats. I sat stunned, trying to assess what just happened.i knew that my neck at the base of my skull was burning, as i reached to pull the dash mat off of me i realized my rightarm hurt.i still hadn't taken my foot off of the brake and i couldn't believe what just happened. I have been rear ended ...almost $5000 worth of rear end damage, and medical bills for whiplash and a broken elbow!i am being told by chrysler that there is an active head restraint recall (this restraint could have prevented my whiplash).loss of work, and medical costs, had to hire an attny. Against the other driver, still trying to recover my financial losses.
The contact owns a 2012 chrysler 200. The contact received notification of nhtsa campaign number: 13v282000 (electrical system); however, the part to do the repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. On a separate occasion, when the brakes were applied and the gear was placed into park, the vehicle accelerated through a wall. The air bags deployed. There were no injuries and a police report was filed. The vehicle was towed to the contact's residence and later towed to geico. The front end of the vehicle was replaced. The dealer diagnosed the brakes. The manufacturer was notified. The approximate failure mileage was 51,000.
When driving, after a rain, especially when turning corners water comes rushing to the front of the car from underneath the dashboard.most times the passenger side is drench and the driver side is slightly drenched but i'm sure this a problem because there must be wires exposed.please help.
The contact owns a 2012 chrysler 200. While driving 45 mph, a loud noise was heard. The contact pulled the vehicle over and noticed that the front passenger side fender wall was loose and wrapped around the tire. There were no warning indicators illuminated. The contact was able to detach the fender wall from the tire. The vehicle was taken to an independent mechanic where it was diagnosed that the fender wall needed replacement. The front passenger side fender wall was replaced. A month later, the contact drove over a hole and the fender wall had to be replaced again. The issue recurred a third time, but the fender wall was not replaced. The manufacturer was notified. The failure mileage was approximately 135,000.
The car accumulates debris below the windshield under the plastic tray which clogs up a drain tube which then makes the water flood back through the heater core into the passenger side of the car . Wetting the floor soaking the carpet and causing rust and black mold. I had it fixed once, but after investigation into the chrysler cars that this is an on going problem with all their vehicles for yrs now. This needs to be recalled and this design flaw fixed. Either they need to have free maintenance of this or they need to have a separate tube for rain drainage and a different tube for ac heat drainage.. It has cause depreciation of my over all resale value of this car plus caused carpet padding damage rust and possibly mold in my car.. Chrysler keeps laying back on the owners saying maintenance problem .. And charging over 500 to fix it. It's not like an owner can easily clean this area it involves take apart the windshield wipers etc
While driving at 40 miles per hour, the hood flew up, and back, into the window and marked the roof. We discovered that the hood release had been pulled earlier, instead of trunk release. My issue, after closing the now "sprung" hood, we tested the secondary "safety" latch, it did not hold
Within 2 days of purchasing this vehicle, rear brakes were squealing like they would do if they were due to be replaced.i brought it back to the dealership and they supposedly inspected them and told me "its just rust from sitting on the lot and it will clear up after you drive it a while", it continued and a couple months following the first visit i returned with the vehicle and told them it still was making the noise and they checked it out again and said "oh, its just dust on the brakes and if you step on your brakes hard at about 40 mph that should take care of the problem".here we are 2 years later and the rear brakes still make the squealing noise.about june/july of this year timeframe i brought my vehicle in to the dealership because i have about 5 different spots on the hood and grill of the vehicle has the paint "blistering" and rust underneath.the dealership didn't call me and tell me what they were going to do about it so i called them about a month later.the warranty guy at the dealership told me that chrysler was going to "send a whole new hood" which i guess didn't make much sense to me but whatever.to date i haven't heard from the dealership any further on this matter and the vehicle is nearing the limits on the warranty period for mileage.the dealership i have been dealing with is john hirsch's motors in cambridge, mn.
On several occasions my family was injured with severe cuts due to delamination of the door handles. This affected every door that saw regular use. I was cut, my wife was cut and my daughter was cut. Doors affected were: driver, front passenger side and rear passenger side. The delaminated chrome on the door handle creates a razor sharp edge. The cut occurs when operating the door handle.
The contact owns a 2012 chrysler 200 convertible. When attempting to close the convertible top, the latch used to secure the roof failed without warning. The vehicle was taken to dodge chrysler jeep of winter haven (299 cypress gardens blvd, winter haven, fl 33880, (888)-612-3182) where it was diagnosed that the roof module failed and needed to be replaced. The dealer informed the contact that the part was discontinued and recommended the contact locate the part. The vehicle was not repaired. The manufacturer was notified and advised the contact to try to locate parts throughout her state. The failure mileage was 97,000.
Replaced disc breaks pads 3 times last year and 2 times this year, the rubber boot inside the break caliber melted and the rear breaks sometimes smokes, now front break pedal goes towards the flow andwith clucking noise, andtbe abs break light is onwhile i was driving..
First time driving the car in snowy conditions,there was about an inch of snow on the ground.i had a very hard time controlling it,it will swirve all over the place,i'm a truck driver used to the worst conditions,i would say i'll rather drive a p/u truck(2wd)without extra weight in the bed on ice..
My car has 42k miles. Air bag light is on. Second issue is a clunking noise in left front wheel and can be felt in steering wheel while in motion.
Van horn chrysler and dodge in plymouth wi. Sold me a vehicle that was in a major front end accident. When they sold me the air the airbag was not attached. The steering was pulling to the right. The suspension was severely damage, it was so severe that when i took the car to chrysler, i spend money there to get the problems repaired. Because van horn wouldn't pay for the repairs. After chrysler couldn't make the repairs, because the car had been in a major accident from the previous owner. Chrysler referred me to the body shop, where i was out of pocket for another additional repair.i also forward this information to chrysler customer assistant1-888-992-1997. My case number there is [xxx].they (chrysler customer assistant) said the car should have never been sold. They informed [xxx] manger to get in touch with me to make a settle. Which he hasn't as to 10/14/205. Tom boweo was the person that i spoke with at milosch's palace collision center, lake orion mi. (248)276-6653. The car is registered to [xxx]. My email address is[xxx]. My phone number is [xxx]. My cell number is [xxx]information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6).
When purchased this car, noticed that it pulled severly to the left,spoke to dealer ship and they stated that it was normal for front wheel drives to do so.so i continued to drive this car but always having to be on alert when driving on highway if car was going to jerk off road. This car handles horrible! i do not feel safe in this vehicle and do not feel if any control was lost, that i would be able to regain control due to this.the dealership has denied that i have ever brought this up, but when my brakes started squealing around 7000.00 mile i then brought it up again and they told me i needed a front end alignment and new brakes! ok i just bought the car... I told them no, how could that be.well since then my car has had to have the cylander replaced and they have addressed the jerking with a front end alignment which by the way did not do anything. It still is hard to control and could only do 30 mile an hr in snow before it would loose control. I have more complaints and have addressed chrysler to no avail. They just tell me its the make of the car and that my brakes squealing are because asbestos is no longer in brakes. I told them that i was not born yesterday and have driven more cars than this and never have had this problem. They offered me an extended warrenty and stated that was all anyone could do .i am a very unhappy customer and becasue i am in a lease i can not get out of this car. Only when it crashes will anyone maybe do anything about this.i am seeking the state attorney in idaho to see if they can help resolve this issue .
I have made several complaints to chrysler regarding the vehicle not accelerating when it should and not going over 35mph at times.when the vehicle won't accelerate the 6 speed does not work either.chrysler reset the computer and this worked as a fix for roughly 2 days until it happened again.the vehicle also jumps forward when braking and seems to be jumping very hard through the gears,chrysler has responded every time that they cannot duplicate the problem and to bring it back when it happens again. Today i was driving to work and again the car was jumping when i was braking.the car in front of me braked hard and unexpectedly therefore i had to as well.my car did not stop! although the brake pedal was pushed as hard as i could the car jumped at least 6 times and made a horrible grinding noise before i finally was able to get it to stop before rear ending the car in front of me.i did make it in to work however, the car did not make any improvements after this, now every time i try to stop the car jumps forward.this car is going to get me, my kids or someone else seriously injured and chrysler has no sense of urgency to seem to get it fixed.from what i have read it is not only my car that is having the same problem.add it to the lists of recalls please!!!!! also when i am driving and this happens daily the car jerks very hard between 1st and 2nd gear, this literally causes the car to and feels like it may stall out.
After driving for about 15 min. You can start hearing a clunking noise coming from the left side, and you can feel it in the steering wheel.don't know if its steering or suspension, but i get eerie feeling the car may lock up.
For the past couple of months i have been experiencing my car fishtailing badly in winter weather. In the slightest snow fall or ice it fishtails so badly causing me to slow down to speeds around 35 mph on the highway. When i first noticed it i thought it was my tires and alignment so i had bought new winter tires and had the alignment redone but after driving it soon after i realized that it did not remedy the problem. So i thought that maybe adding some weight would help but it dangerously got worse. Tonight i was driving and hit a slight patch of ice and it fishtailed so violently i almost went off the road and almost caused a semi truck to crash just to avoid me. This car is not safe by any standards of winter weather driving. Even a friend of mine who is an auto mechanic agrees that this vehicle isn't safe. It feels as if the rear suspension is loose but when inspected i was told everything was fine. Please look into this. I use to drive a toyota yaris that did way better in winter weather than this and mind you it only had the factory tires. Thank you.
For weeks now ive been noticing a weird grinding or dry rubbing sound underneath the front end of my chrysler. Checked it out a few times, as though i am not a mechanic i can identify the basics of something not right. However, after my husband and his brother both looking it over on seperate occasions, they have noted a leak under the carriage of the car. Often here recently, the guage senses an over heating of some sort. Since this notice, we have replaced the oil cooler twice in a year; as well as flushed the hoses associated with the coolant reservoir. Fixed temporary but has now already started getting too hot. Which simply tells me that its something further internal thats wrong. I was informed of an engine recall: l33 of my chrysler model. However havent seen one on this website. When driving yesterday, i noticed a light on my cluster that indicated the traction has failed. When i brake, all u hear or feel is a vibration under your feet, up front. I replaced my brake pads all 4, within the past 4 months and theyre now rusted over and u notice a brake fluid leak on the front right side. After a light, the grinding noise, the vibration and the overheating; i am positive that this will eventually cause a car stall or worse a fatal accident. My brakes could eventually fail while driving in traffic, causing a crash. Or my car could just all out stalland the cluster can trip and i could be in harms way if at the time it does this i could be goin 70 on the interstate or in a turninglane in town and without proper fix; it could easily cause a fatal accident and i could be killed or worse my children!
The contact owns a 2012 chrysler 200. The contact stated that while driving approximately 15 mph in the rain or snow, the vehicle pulled to the left. The contact also stated that when the vehicle was turned to the right, it made a loud "bang" noise. There were no warnings in either event. Both failures were not diagnosed. The manufacturer was not made aware of the failures. The vin was unknown. The failure mileage was 34,000.
Was driving car going only 25-30 mph and made an attempt to slow down to a stop which i had plenty of time and space between car in front of me and my front fender to do, as i applied brakes i notice it go all the way to the floor and my car wouldn't stop which soon after having plenty of space to do it led to a rear end collision as my brakes failed to work correctly when applied. I have a police report to verify the incident on 09/27/2016 in appleton, wi. Because i was going at a really slow speed at the time luckily no one was really hurt when this occurred around 10:00 am in an area with little to no traffic at the time, but even know i was only going around 20 when there was an impact my car which was new prior to this accident is now considered under state law in wisconsin a salvage vehicle as repairs exceeded the value at the time of 7000.00
When driving the vehicle at speeds 30-70 mph in a straight line and encountering slight dips or bumps in the road surface, a dramatic loss of directional control was experienced at the left rear of the vehicle. The condition is best described as a sudden, violent swerving from the left to the right. The vehicle was very difficult to keep within the lane. This was a rental car from a commercial agency. I returned the vehicle in another town on my trip route, described the problem and was given another car. In a search for similar events on this site, i found one for the same make and model vehicle on a 2011 model year. The id number of that complaint is 10444871.
Salutations;i have already contacted chrysler about this problem. Their response was to basically blow me off.the problem is with the rear suspension of the chrysler 200. When ever the rear suspension hits a recessed man hole cover or a pot hole. The rear suspension seems to kick out from its trajectory. This always happens in a straight line, but when in a corner this is very spooky and unnerving. And could be a safety problem in icy/wet road conditions. This happens at all speeds above 30 mph. I do not know if it is with the joint and rebound of the shocks , or a problem with the angle of attack within the trailing arms and set up. It simply should be a factory misalignment. I also had to return to the dealer to have the headlights adjusted because i could not see past 20 yards. This was adjusted immediately at the dealers. This suspension condition has also been reported in a couple automotive magazines i read.
Excessive "fish tailing" in minimal snowy conditions, very unstable, absolute death trap. I felt like i was going to end up smashing into a passing car or truck . Drove for 30 miles per hour for 260 miles while there wasn't more than one inch on snow on the ground because the rear end of the car was swing in all directions, my wife and daughter terrified. I just bought the car back in august 2013 thus a few months ago and had no issues driving on dry ground but only in snow and wet conditions.
The first time i drove this car and snow i could barely keep it on the road.i have been driving in michigan for 24 years and i have never had a car that handled this poorly in the snow.i took the car to my dealership and they told me it is a common problem but chrysler does not have a solution for it.since then the dealer has split a set of snow tires with me but it only partially helps the problem.the car is terrifying to drive in any snow conditions regardless of the snow tires.it moves from side to side in the snow and can barely be kept on the road.i have a 2 wheel dr. Truck with no wait in it and i'd prefer to drive that over the chrysler in the winter.
Awful popping noise to front end when driving. Worsens over time . Had to shop 4 times. They now admit to a problem with tie rods at manufacture. Dealership is offering to fix with a $100 co-pay since it is now out of warranty mileage. I am working with chrysler to get the rest covered since it is an unresolved warranty issue.
The contact owns a 2012 chrysler 200. The contact stated that the abs warning light illuminated as the front end exhibited a loud metallic noise. The vehicle was taken to the dealer where a diagnostic was performed, which located the failure at the driver's side front wheel bearing. In addition, the abs system was faulty. The dealer disconnected the abs system. The driver's side front wheel bearing was not repaired. The contact also wanted to add that the water pump was replaced due to loud noises that were emitted while driving. The failure mileage was 17,000 and the approximate current mileage was 21,000.
This vehicle out of service .could of cause a collision or cause body injury or death ,i started the car went about 100 feet or more, car made a loud noise ,car stopped suddenly by itself, then brake part flew right off right on the road. Had to push car to the nearest corner.called dealer service, called my insurance.i have full coverage, but no response at the time. I signed hardship packet from the bank for help, but was repossessed, so dealer could not pick the car .i made a complaint february 12,2013 to bakersfield chrysler - jeep about my brakes squeals and my tires always display low pressure. Service dealer said there is nothing to fix they squeal because of dirt and they are wet and tires need more air because of weather change. I brought this car brand new. I sent a formal written letter addressed to nhtsa, plus documentsthat will substantiate my situation.updated 03/13/14
The contact owns a 2012 chrysler 200. The contact stated that while driving 35 mph in the snow, the vehicle would sway to the left and right. The contact stated that he decelerated and the swaying stopped. The vehicle was not taken to the dealer for inspection. The vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was 60,000... Updated 03/24/14
A recall was issued by the manufacturer for the emissions system and we brought the car in for repair. We we're told that the parts were on back order and we would have to have it done later. Now, seven months later. Upon contacting the dealership, they have the vehicle listed as complete without any repairs.
My vehicle has roughly 54,000 miles. The heat does not work on the passenger side of the vehicle and is progressively becoming colder on the driver side of the vehicle. The car will not reach a warm enough temperature to be comfortable or to adequately defrost the windshield. This is a known issue to chrysler and should be recalled. The parts involved are the heater core and radiator.
Only heats on drivers side ,cold air only on passenger side
The heater on the passenger side of the car is not heating up and blows very cold air making it hard to defrost the window to see when driving
Problem description: windshield wipers only work on high and when you turn them off they just stay in any position.
Car is stalling unexpectedly when slowed down or stopped at an intersection. Towed twice. Taken car to three different mechanics, including the chrysler dealership. Paid over $1000 and still stalling. First two mechanics could not figure it out so took to dealership. They stated it was the throttle body and back brakes. Paid $960, picked up and didn't even make it home before it stalled twice. Not easily restarted. This car stalled on me, while 5 months pregnant and two small children in the car while turning left across the lane of oncoming traffic and another time so my husband in the middle of a busy intersection. I have researched that this is or has happened to many chrysler owners and was rated low risk and not recalled. I would love to know how this is low risk?
I am an owner of a 2012 chrysler 200 and on feb. 1st while sitting in my driveway a fire started in the internal. I called chrysler and i received a letter that they will not take responsibility for any manufacturing or assembly error. A week prior before the car caught on fire the heat would only work on the driver side. This vehicle is not safe and it is very disturbing that a company like chrysler would not take responsibility for an unsafe vehicle.
I bought this car from a used car lot, just a month ago. Someone told me about the recalls on it. And it has never been been fixed, i have a 2 yr warranty on it. Do they fix or someone else. I'm scared about these recalls
Passenger side heater does not work windshield and side windows ice over in cold weather so i can't seewhile driving weather has warmed now but problem is the samr
The heater does not blow hot air on the passengers side anytime
The window controls on the drivers door stopped working. None of the windows will roll down. The car was not in motion or in any accident, they just stopped working
When i turn on the heat, the passenger side vents blow cold air. This is a problem to drive using my air/heat because it's draining my coolant. This causes my temperature gage to rise. This happens regardless of my car being stable or in motion. This, at times, also causes my windshield to become foggy.
I keep getting airbag icon airbag error message. I was instructed by insurance to run vin to see if there has been a recall upon running vin i was notified there was 3 recalls listed for vin.
Chrysler 200 heating issue, hot air on the driver side cold air on the passenger side. I live in a northern state and in the winter especially during storms the windshield needs to be heated on both sides so that it doesn't ice up. This could become a potential hazard when your vision is restricted because you cant defrost your windshield due to a design flaw in the heater system that chrysler doesn't want to have to repair. How many have to be injured or killed in order for this to become a design issue and have a factory recall done.nothing has happen to us yet but today is the first storm of the season
My chrysler 200 died while driving--still had power, but engine died. The first time,6/8/19, we thought it was a cam sensor-that was the code it threw at the mechanic.we replaced it.then the battery light came on.the battery was good, but the alternator wasn't-so we replaced the alternator.drove it for 2 days & it died again, 6/16/19.took it back & the same cam sensor code is popping up but sensor is still good.got it back, drove it another 2 days & it died again, 6/22/19.towed it back to shop & mechanic cannot duplicate the problem after a week.have it back 1 day & car dies again, 6/29/19.several complaints here mention the car engine dying for no reason, but still have power.we've been lucky-we haven't been on a highway when it's died.each time, we've been driving around the city & making a turn & the traffic flow has been slow.sometimes we've been at a complete stop-others we have not.being that this seems to be a repetitive complaint, why hasn't a recall been issued on the vehicle??
The heater on the driver's side barely warms up works and there's no heat on the passenger side. Only cold air blows no matter what setting i have it on. This is not good in the winter months when is -2 degrees and the heater doesn't work on one sidei was told the heater core was plugged and it can cost between $800-$900 to fix this is a known issue with chrysler and it should be recalled.
On nov 7 2016 at roughly 7pm, i was heading west on the 10 freeway location 34.065990,-117.993771, baldwin park, ca. Traffic started to slow to 45 mph then came to a sudden stop and i was the last one in the 4 car collision. My airbags did not deploy and. I feel that the brakes may be faulty for when i stepped on them as hard as i could it seemed to be more of a skipping stop. For the littlest bump feels like ur hydroplaning to a stop. Chrysler never informed me of any recall about the airbags though i felt they should of deployed. My car was in the shop till march so i havent had it back but a few months.
Heater core...do not purchase this vehicle. Don't take my word for it, research reviews of chrysler's negligence with many makes & models for their ineffective heater core.the cost to fix is not cheap (i can show receipt) very few shops will work on heater core for this car.car has a serious issue with heater core, & i do not want to even give my story as i would just become even more infuriated. Ashame no lawsuits have been successful against chrysler. It's bad enough these idiots designed a vehicle you have to take off entire bumper for to change headlight bump (which cost double the amount of the already expensive bulb).worst purchase ever made, chrysler could give me a car for free & i would refuse to to keep it at this point. Never ever again. Just say no to chrysler
Head rest on the front passenger side deployed on its own. Looks like the peace of plastic that held the head rest together broke.this was plastic on metal rod.at the time when this happen no one was sitting on the sit.we would of had a very bad head injury if someone would have been there.
My wife was driving our 2012 chrysler 200s with the 3.6l pentistar engine and the engine shut off while she was driving on 03/09/2021 and i came and got her and we tried to restart the car and all it did was crank until the car timed out and no start and the next moring the car started up just fine with no lights on in the dash and this is the 5th time the car has done this and i have researched the problem and its one of two things a pcm udate or a connector to the tipm or fuse box and i want to know why ther is no recall for this and why chrysler only recalled the 2015 model 200
The heater on my 2012 chrysler 200 convertible does not work.the air blows, but it is not warm.i do not have that problem on the driver's side.my dealer tells me i need my heater core, among other things, replaced, which will cost approximately $1500-$2000..in researching this problem, i find it's the number one complaint with this make and model.my car currently has approximately 80,000 miles on it.
The electrical throttle light keeps coming on and the car shuts off.
My cars heater core was plugged. When we went to have it fixed we were told that this is a common issue with the chrysler 200. We had it fixed in february 2016 for $800. Now in november 2016 it is plugged again!
Heat only coming from right side of car, any setting i use. Heat only comes from right side of car. This seems to be a known issue on chrysler/dodge vehicles. This is a safety issue, cannot properly defrost car, windows ice over, unsafe to drive especially with children
I had the seatbelt fixed due to recall but i almost got into accident as i could not pull the seatbelt . I felt like it was choking me . The second problem which is the current . I have been experiencing when you start up the car there are times it will start right away and there are times that i have to try it to start between 3 or 5 times. Brought the car to the mechanic 3 times in 2 weeks. . i have a brand new battery, not even a year old alternternator, spark plug is also new, brake is new and another parts was replaced which cost me $300. Today , december 19, 2019 i brought my car to the mechanic to have the problem diagnosed but on the 13 detected none of it has error. . please help me. I already spent so k in money to get it fix . I don't know what else the problem . Been to two mechanics and both of them can't find the problem. I can't afford to go back and forth to the mechanics and i am still making payments to the car. Please help!
The car had only 35,000 miles when the issue started. The passenger heat is cold, and the defrost will not work, while the driver's side gets warm, and will defrost a small amount of the driver side windshield, and nothing on the side windows. This issue is a hazard for visibility in the winter. I have researched the matter to finds this is a common issue with the chrysler 200 and has a repair bill of $1500 as the passenger side has a blockage or clog in the system.
The passenger side heating vents blow cold air and the windshield will not defrost on that side causing a safety hazard.not to mention i live in montana and it's seriously cold then having cold air blowing in the car is horrible.
Single short random high pitched beep coming from dash but no warning lights. Happened when car was off and keys was out side the car. While driving on the interstate, it beeped again. Once again, no lights. Checked all fluids, all full. My tps sensor light has been on since i bought it 2 years ago.just needs a new sensor but it'seems never made a sound.
Heater blows out cold air i have no heat i cant defrost car windows to see .this has been happening since 2016 jan i have replaced actuvator blendoor 3 times ....thermostat 2 of them... Flushed the heater core .....found out i have a sludge or blockage in my radiator and heatercore plus need radiator cap 2500 to fix ? its a 20
Takata recall...i purchased the vehicle 2 months ago at darcars in marlow heights, md and i have already put the car in the shop 4 times for different issues. The biggest issue is after 2 weeks the engine cut off on the beltway(i 95) while heading to the store. Thank the lord that i was able to get on the side lane but i was almost hit by 3 cars, also, 2 weeks after that while driving the engine became very, very loud on the road so i ended up putting it in the shop for 3 days. It is a shame that people/dealers can sell lemons. Please help me with issue to get my money back from the dealer...$12,000 i can be reached at (301)613-8819. Thanks!
I had the transmission rebuilt by chrysler 2014, it has been back to chrysler twice since then and they say nothing is wrong. It is now out of warranty and the transmission is slipping again. The car also has some electrical system issues, the radio will just stop working and the lights will dim.
I purchased a 2012 chrysler 200 from carmax located in memphis tennesse back in july 6, 2015. After a few days of purchase i noticed the brakes were not working properly. I took the car back in immediately for service and the service manager advised it was just a small problem and assured me that it was fixed. In august i had the same problem and took it back to the service department ( please be advised i am employed and i have to drive from pine bluff to memphis) at that time the service manager advised that it was some kind of fluid and the problem was fixed. This was all done during the factory warranty. On november 8, 2015 my brakes began to drag and was barely stopping i took it back to the service department and demanded for the problem to be fixed back to factory profection. Mr. Joe brown advised that it would be covered under my warranty but i advised that the car was never repaired correctly under factory warrenty. I had to pay a 50.00 dollar deductible and fifty towards a rental car deposit. I was called on 11/13/2015 and adivsed that my car was ready. I couldn't pick the car up until saturday morning 11/14/2015. When i came to retreve my car my car was just sitting in the parking lot and no service worker was there to drive the car with me to ensure that it was working properly. In conclusion my brakes are still not working and it could have caused me my life on this morning 11/17/2015. The brakes are worse.i am in tears because i am a recent graduate and i am working to pay bills and student loans. This is what place american people in proverty when someone sales you something and it only works for a short period and you pay for warrenty and that doesnt help neither. Please help.
Dear sir/ madam:11-08-15a fireoccurred at my house which was located at [xxx], on the above date, i parked my 2012 chrysler 200 in the garage and went to bed. Approximately 45 minutes to 1 hour after retiring, i was awakened by a loud explosion and my neighbors beating on my front door to awaken me and my 21 year old grandson.he also was sleeping in another bedroom. When both of us attempted to escape from the house through the kitchen/garage entrance, we were met my heavy bellowing grey and black smoke that prevented our exit and almost overwhelmed us.several months later, i am yet suffering from the shock and emotional trauma.because of dealing with flashbacks, nightmares, intermittent waves of nervousness, deep sadness, feelings of grief/loss, periodic confusion, digestion issues, and numerous financial concerns, i am in professional counseling.i have been unable to write this letter until now.even now, a friend is assisting me with completing this communication.this is the second contact i have had with your corporation.the first was the morning after the fire, when my son called on my behalf from his cell phone.he was informed that there was no recall of this particular chrysler 200, however there were some known problems with the gas tank and ignition systems that were built between march and november of 2012. Please understand.i lost my house, 23 long years' worth of cherished belongings, and the car i recently purchased. I lost everything in the fire.i decided that,i would rather initially contact chrysler directly.my hope is that chrysler will understand the gravity of the situation and do the right thing without going through expensive attorneys.[xxx]https://onedrive.live.com/redir?resid=cebfb7d86d50e64d!750&authkey=!aalipdbqwpwsze8&ithint=folder%2cinformation redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6).
Takata recall" i had a accident on 7/12 in the afternoon time when it happen i was completely stop at the red light behind one other car an the car behind me ran into the back of my car so when i was hit from the back i went forward into another car my seat belt didn't tighten nor did my air bags come out an i hit pretty hard into the back of the suv that was in front of me. Hitting my head an chest on the steering wheel my shoulder hurts an the back of my neck hurts as well. We have a police report done an now i have to go to achiropractor i am very up set i could have broke something thank god i didn't. I would like someone to contact me about this matter.*dt
The passenger side heater and defroster stopped working. It is a known heater core issue caused by faulty coolant causing sludge build up in heater core. Mechanics know of this, chrysler knows of this. Without a fix the windows can struggle to maintain visibility, and maintain heat levels. The fix is to replace the heater core and/or radiator. Which can be $1200-$1800, here is a web link to a multitude of complaints http://m.carcomplaints.com/chrysler/200/2012/ac_heater/heater_doesnt_work_passenger_side.shtml
I think my car has electrical issues window start and stop working . I replaced a headlight and it starts and stops working at one point my started stopped and started working. My headrest deployed on passenger side while driving and it's a big space now on it
Heating and cooling. When turning on the heat, the system blows cold air on the passenger side. Then if the car is in idle for a little while then both sides blows out heat. But more often, when the heat is on, it blows out cold air.
On 1/12/2020 while driving home from work i turned on my right turn signal to merge and it rapidly clicked and flashed on the dash after the initial 3 normal flashes and i noticed the car in the lane next to me wasn't acknowledging my turn signal. Once home an hour later, i realized my passenger rear tail light was steadily light (not flashing) even though my car was off and my lights were not engaged and position off. I could not get my turn signal/tail light to turn off. The brake lights work fine when the brake is applied but the tail lights will not turn off. The rear signal won't work either since the light won't turn off to flash. I had to remove the light from the rear fender and unplug the light so my car won't die and plug it back in when i go to drive so i atleast have the tail and brake light on while driving. I can find no info on how to fix this and chrysler wasn't any help. The problem is still unresolved, but it did go off for just one moment, flickered and came back on when i plugged it back in the last time i drove.
Alternator dies at 78,000 miles. Heat no longer works due to heating core at 60,000 miles.
Transmission is going after just 8 years old!!!!!
Drivers side head rest deployed while vehicle was parked,it is very fortunate that this happened while no one was sitting in the chair at that time.my question is, will this also happen with the drivers side head rest?
My horn started honking on it own.i first noticed it when i was outside the car and had not touched it, the horn started honking.i got in the car and it stopped.every time i drive the car the horn honks on its own, sometimes long honks other times brief.the next thingit started raining and the wipers would not work properly they would swipe halfway and stop, only working when on high.finally i was driving home and the car stopped in traffic.i sat for a few minutes and started it and it would stop after moving for about an inch.the car stopped three or four times and finally i was able to drive the 2 or 3 miles to my home and park.
There is no heat on passenger side so the defrost does not work and it affects visibility when driving.
Vehicle stalled and would not start while driving (2 times )towed to dealer as (both times) tow driver could not restart.dealer reported no computer codes and car started after car started on problem.there appears to be common safety hazard that has been experienced by many owners, that reportly chrysler and nhtsa agreed upon a resolution to avoid a recall by chrysler of this safety hazard in sept 2012.chrysler doesn't acknowledge and not sharing this information with dealers so they can take corrective action. Various attempts tried to resolve this hazardouscondition have included replacing the powertrain module, camscope replacement, monitoring the on board with a copilot computer-which also showed no codes.the dealer did say that chrysler suggested an additional module be added to the on board computer, but none of their customers returned a third or more times as previous attempts were unsuccessful and appeared to give up.this life threatening safety hazard needs to beinvestigated and resolved, as we were driving on aroadway and the motor just shut off.,if this not resolved it will sometime cause injuries or deaths, which could end up with a recall something that chrysler possible replacement of on computers.
While driving 45 mph on a highway, my car just died. The speedometer fluncuated, all lights flashed on and off, then just died completely.
First time car wouldn't start.dealership charged battery and did software update.second time car wouldn't start they replaced battery.third time car wouldn't start battery completely drained they said it was a glove box switch.fourth time car wouldn't start they said it was the usb cable keeping the radio powered on all the time.same chrysler dealership worked on it all four times.brand new car bought august of 2012.all four times have been in less than two months!this car is not safe.chrysler is not doing the right thing by their customers!any help would be appreciated.in the usa we should not have to put up with being ripped off like this.
I was driving on the expressway and my car died without any warning. I brought it to the dealership and they said i had oil in the injectors. They cleaned it up and sent me on my way for $715. Not even a month later i'm still having the same issues and nowsometimes it's not starting. So another repair shop changed the battery and starter, after the work they run some tests and say that i have a bad tipm to bring it back to the dealership. I bring it back to them and they want around $1800 now for this repair. I called chrysler and spoke with them about this and they refused to help in any way with this situation even though we are loyal dodge family customers(on our 5th vehicle). The reviews online show many people having this issue and it is a very dangerous and scary experience having your car die in the middle of the expressway with no power steering. I definitely think there should be a recall for this part to save the lives of others on the roadways. Thanks in advance
I have replace the air actuator door twice what seems to be the problem with this he keeps breaking making a clicking sound
Differential exploded while pulling away from a curb into the road, no traffic, no excess accelaration
As i was driving on the highway, the car shut down completely. The steering wheel locked and it would not restart. This is the third time this happens, and twice, the dealership tells me the there is nothing wrong with my car, but this keeps happening.
The wiper blades come on by themselves and stay on for about ten to fifteen seconds. They shut off by themselves as well. I can't shut them off.
I own a 2012 chrysler 200, i love my car; however, the head lights are pointing towards the ground making it almost impossible to see anything in front of me while driving. I've changed replaced the headlight bulbs as well as cleaned the headlamp. Unknown 2.during the winter months my car makes the grinding noise when starting up.
My car heating system only heat half of the car and you can smell antifreeze coming through the vents. The passenger from window has stop working, it will come down but want go up. And the two windows in the back is trying to stop working. I just got this car on 11/01/2015 with only 32,000 miles on it.
Driving with knocking in steering, in back rear right tire,feel and can hear knocking in both places when driving, took into shop where car was purchased and they said no problem, but i think it is a problem when i'm not able to drive the car over 20 miles away from home and back without it doing this.and i'm still making payments on this car, i put a 3 yr. Warranty on this car and still look like they are giving me the run around!!!!!!!!!!!
The passenger side of my defrost/vents does not work--it remains cold even on high heat and driver side hot. The windshield and passenger window remain foggy or ice covered, or after removing the fog or ice it rebuilds fog or ice while traveling on highways while snowing, extremely limiting visibility. This winter has been quite difficult to drive safely due to this condition.
Only when heater is on, whether on defrost or front vents, blows cold air thru just the passenger side vents. It happens when the car is on.
2 complaints/concerns:1) this affects the 2012 chrysler 200 i purchased used with 62,500 miles. It's been well documented all over the internet and at chrysler dealerships how the 2012 chrysler 200 was part of a group of vehicles with faulty antifreeze from the factory. This antifreeze breaks down and will clog the heater core, radiator, and transmission oil cooler. The recommended repair, from chrysler, is to replace all of these listed parts at a cost of about $2500.00. Chrysler knows about this problem, but refuses to do anything about it. My car is at a chrysler dealership as we speak having these repairs made.2) this one i have not experienced, but i also see a large number of reports where the pentastar v6 equipped in a number of these vehicles will suddenly shut off. Many of these cases are when the cars are in motion. This is a serious safety concern. Issue seems to be centered around a pcm, but there is no recall of any kind on this.
The catalytic converter was changed on tues., july 30, 2019 as the result of a recall notice from chrysler.was told after the replacement was done that i would smell burning a little for about a week until the new converter was broken in.i did smell this while driving.it was driven the following day for a total of approx. 80 miles.my lungs were affected badly.brought it back in to the shop (chrysler certified) next day, but no problems found.drove it one more day, but the pain in my lungs increased.since then, have not driven the car.was diagnosed by a doctor with asthma and put on a steroid inhaler.never had lung problems previously.chest x-ray and pulmonary tests normal.chrysler wants me to bring it to another certified shop for review, but it is far and would require towing.since then having a lot of pain in my lungs 3 weeks later.i believe it is because of the new catalytic converter.
Heat stopped working on passenger side. Defrosting is more difficult being that the air is not warm in cold temperatures. Prior to the heat not working on the passenger side the a/c stopped getting cold too. (it was getting cold only on the drivers side)
Clunking noise in the front drivers side wheel. Vehicle drive straight but there is a clucking sound that can also be felt in the steering wheel while driving. It happens now all the time when diving highway or side streets lower speeds seem worst under 40 mph, started a few months ago and getting louder.
When driving my vehicle i had three lights to come on which resulted in having to take my car to have a diganostic test, the out come was the throttle position censor in which i have never had any problems before from any of my chrysler vehicle andthe repairman said this is a dealer defect. I am very disappointed that i am going through and ordeal since i have owned many chrylsers with no problem.
No heat to passenger side of car due to plugged heater core. Well known issue causing reduced heat to vehicle.
Takata recall: there is a problem with the electronic throttle control light that causes the car to decelerate randomly, in combination with a ticking sound that comes from the air bag area of the glove box that is exacerbated by the ac and the heat being turned on.i feel that the car is unsafe to drive, although it says there is no open recall on these components.this happened several times to me on the expressway today.
Catalytic conventor isn't ready to pass inspection, i seen some possible recalls for fav but haven't received a notice...
My vehicle has no heat coming from the passenger side vents. The heater core is partly plugged. I worked for chrysler as a mechanic up until a few months ago. I have personally run into this same issue with customer cars as well as several other techs. Chrysler will not cover the repair due to it now being out of basic warranty.
Cold air blows out passenger side vents
The car accumulates debris below the windshield under the plastic tray which clogs up a drain tube which then makes the water flood back through the heater core into the passenger side of the car . Wetting the floor soaking the carpet and causing rust and black mold. I had it fixed once, but after investigation into the chrysler cars that this is an on going problem with all their vehicles for yrs now. This needs to be recalled and this design flaw fixed. Either they need to have free maintenance of this or they need to have a separate tube for rain drainage and a different tube for ac heat drainage.. It has cause depreciation of my over all resale value of this car plus caused carpet padding damage rust and possibly mold in my car.. Chrysler keeps laying back on the owners saying maintenance problem .. And charging over 500 to fix it. It's not like an owner can easily clean this area it involves take apart the windshield wipers etc
While driving car shut off. Also windshield wipers not working properly.
Randomly shuts down while driving down the road,with no warning
Passenger side heating and defrost not working and barely working on driver side. Will not defrost causing trouble with visibility... There have been numerous complaints about this very same issue on "carcomplaints.com" the issue became noticeable when it state to get cold in november and december of 2017 around 68,000 miles
My cars a/c heater blend door actuator has gone out. Upon my research i see there are numerous chrysler 200 owners with the same problem. It is my understanding gm recalled the same part from the same manufacturer. Shouldn't chrysler recall the part as well? the problem is persistent in the part continually clicks, cold air running through the vents when the heater is on.
The car consistently stalls out at least 4-6 times a trip in the middle of driving, if not more. It also honks on its own during that time.it was brought to the dealership and a shop and they couldn't find anything wrong
4 week agao i bought a chrysler 200, 2012. Since i heard a noise in the front wheel. I bring it back to the dealer they said they fix it but still making the noise. Please for my safety and our safety can you please push for a recall, because it is not only me with the same issue, things getting scary... Please please
When i turn on the fan when using the heateror the air conditioner there is a noticeable clicking sound coming from the dash on the passenger side of the car. The sound at this time is lasting about 30 seconds or so then stops. This happens when driving or standing still.
The passenger side of the vehicle blows cold air while the heat is on. The driver side blows luke warm air, thus ineffectively heating the vehicle. I have been told this is a known problem with this model and is a defective heater core system. The estimated cost to fix is $900-$1200. Living in michigan, and not having heat during the winter is a major concern for safety.
My transmission is slipping and not performing the way it should.sometimes my car shifts hard and sometimes it won't shift out until it reaches 5 or 6000 rpms which is almost in the red zone.when going up a hill or incline it hesitates and jerks.i called several dealerships only to be told that there were multiple cars ahead of mine that were just sitting there with the same problem.i was told that they were waiting on a call from corporate to fix the problem. To this day it has not happened.also, my airbag light has been on for almost four months now.they said they did not have a fix for it yet. Just recently there is a knocking noise coming from the passenger side dashboard. An ongoing problem has been the noise from the front brakes when i am backing up. I was told there was no fix yet for that problem. As of this day, there still is no fix for it. I am still driving my car because i can't just leave it to sit at the dealership waiting on repairs. As you all know, they do not give out loaner vehicles any more at least not in arkansas.
Air bag light is on , going threw brakes and tires every 6 months sense i bought it in 2016. Also no heat started at passanger side and worked its way towards drivers side. Also front windows do not go down started passanger side and 3 months later no driver side. Also was driving about 35 mph made right hand turn car has stalled 5 times.
The heater core gets clogged up and your windshield visibility will not be cear. Thia will cause unsafe driving measures.no heat my car blows out vool air only.
Heater hose line clogs up with sludge, this is then causingno heat on passenger side , no defrost, and little heat on drivers side. This issue makes driving a hazard as the car will completely fog up make visablilty poor. This issue take about 30 min of running the car before drive to barley take the chill off the car.
I have made several complaints to chrysler regarding the vehicle not accelerating when it should and not going over 35mph at times.when the vehicle won't accelerate the 6 speed does not work either.chrysler reset the computer and this worked as a fix for roughly 2 days until it happened again.the vehicle also jumps forward when braking and seems to be jumping very hard through the gears,chrysler has responded every time that they cannot duplicate the problem and to bring it back when it happens again. Today i was driving to work and again the car was jumping when i was braking.the car in front of me braked hard and unexpectedly therefore i had to as well.my car did not stop! although the brake pedal was pushed as hard as i could the car jumped at least 6 times and made a horrible grinding noise before i finally was able to get it to stop before rear ending the car in front of me.i did make it in to work however, the car did not make any improvements after this, now every time i try to stop the car jumps forward.this car is going to get me, my kids or someone else seriously injured and chrysler has no sense of urgency to seem to get it fixed.from what i have read it is not only my car that is having the same problem.add it to the lists of recalls please!!!!! also when i am driving and this happens daily the car jerks very hard between 1st and 2nd gear, this literally causes the car to and feels like it may stall out.
My cars a/c heater blend door actuator has gone out.upon my research i see there are numerous chrysler 200 owners with the same problem.it is my understanding gm recalled the same part from the same manufacturer.shouldn't chrysler recall the part as well?the problem is persistent in the part continually clicks, cold air running through the vents when the heater is on.
I bought my 2012 chrysler 200 new. Now havingheating issue, hot air on the driver side cold air on the passenger side. I live in a northeast and it's very cold. I can't get the car warm enough for windshield toheat on both sides so that it doesn't ice up. This could become a potential hazard when your vision is restricted because you cant defrost your windshield due to a design flaw in the heater system that chrysler doesn't want to have to repair. Also my kids are freezing in the back seat. How many have to be injured or killed from thisdesign issue and or to have a factory recall done? or kids with hypothermia?
While i was taking off to drive my car, the car shut down. All the lights came on, then everything shut down.the car started, but i could not drive my car.i had to have my car towed.i was told that the alternator went out.this happened in september 2015.i was at a restaurant, leaving to go home.i paid 415.45 for a new alternator.
The abs and terrain lights stay on, when car reaches 60 mph it pulls.
The heat blows out hot air on driver's side but only blows out cold air on the passenger side which will not defrost the windshield and makes it very hard to see which is a safety hazard.
Sudden stall on the highway, completely died on the slop of the beginning of the bridge on april 4,2019 and april 11, 2019
There isn't any heat on the passengersside . The dealer said the heater core and the radiator also the thermostat' s . The said that chrysler puts in a chemical that's supposed to fill in any pin holesand now a couple of years later it becomes sludge and clogs up the heater core and everything else. And now i have a $2900 bill that i have to pay. It's not right for chryslerto do that to the public and get away with it.
Break light in dash comes on and off constantly
While driving the car down the road randomly shuts off and when it happens you have no steering control or braking control
I was traveling 55 mph on the highway my tire blew out an the fender blew off but somehow the cars whole engine wiring system was ripped out of the car in which the whole car went completely dead of all electricity thankfully i was able to pull on shoulder of highway before the car stopped rolling.
Passenger side does not have any heat coming out of the vents, or defrosters. Only the far driver side produces small amount of warmth. Being that i live in wisconsin, it has become hazardous for me to drive my vehicle in the winter for obvious reasons. Not being able to unfog, or defrost your windows is unbelievably dangerous! aside from the dangers of driving at times with only half of a clear windshield, my passengers and i freeze inside the vehicle during the winter! the only way to clear the windshield and passenger window is to periodically open the windows while driving, which only makes the inside temperature that much more unbearable.
No heat . Heater core and radiator had to be replaced by chrysler dealer at a cost of $1600.00. Had extended warranty but would not cover cost. I understand from the dealer that this a major ongoing problem with this model of vehicle but chrysler has refused to acknowledge responsibility only advice on how to repair.
Heat partially operational only driver side.when going up to 70 m/h only cold air come out of vents . A/c not working no leakage after garageinspections .
The dealership wants to charge me $1800 to replace the tipm, but i see other chrysler models have been recalled for the same thing... Except mine hasn't. This isn't just a minor inconvenience... It's very very unsafe: 'the fuel pump not turning off and burning out'the airbags not deploying or deploying randomly'the engine stalling while driving'the starter cranks but won't start'the horn going off at random times'power windows not working'doors locking or unlocking themselvesmy wipers, horn and lights go on at random times. At times it's while i'm driving.... Sometimes it's while it's parked. The car doesn't even need to be turned on for this to happen. It's drained my battery a few times and now it's not even drivable. It started back in november, 2016, but has continued through the present. I haven't been able to drive it for the last 2 weeks.
I was driving my car on 295 s yesterday and it lost power and the hot oil light came on and i had to pull over because i was almost hit by an 18 wheeler and sit there for 30 minutes and it states it is a transmission problemand this is the second complaint i have sent to you and i have tried to callbut no one is answering or they hung up on me.05 .
At a stop sign a woman stopped in front of him and he didn't stop quick enough
The contact owns a 2012 chrysler 200. The contact stated that the vehicle suddenly accelerated when driving, decelerating, or parking as well as with the cruise control was set. The failure was experienced several times. The brake was depressed with force to be able to stop the vehicle. The vehicle was taken to the dealer several times for the failure. The dealer performed a diagnostic but was unable to locate a failure code. The manufacturer was made aware of the failure. The vehicle was not repaired. The failure and the current mileage was 8,000. Updated 08/28/12*ljthe consumer stated the vehicle misfires, uses large amounts of gas, and the transmission is hard to shift at times. Updated 09/04/2012
Regarding my 2012 chrysler 200 speeding up on its own and the cruise control getting stuck and being difficult to disengage. This happened on a highway.
The contact owns a 2012 chrysler 200. The contact stated that while driving 60 mph, the vehicle stopped responding to acceleration attempts. The failure recurred numerous times. The vehicle was taken to a dealer for diagnosis and the contact was informed that the cause of the failure was undetermined. The manufacturer was notified but offered no assistance. The vehicle was not repaired. The failure and current mileage was 13,656.
Entering freeway was accelerating,merged into a lane and took foot off of the accelerator and the car rpms kept climbing and speed kept increasing within 10 seconds it stops and will respond normally usually happens when there is a quick attempt to accelerate.
Car would not accelerate over 20 miles and hour after the traction control and abs light came on. The car then rapidly accelerated and worked fine until i reached work. When driving home it did it again and wouldn't resolve itself. I took it to the chrysler dealer and 1 week and 1,200.00 later they informed me my car was fixed and that a faulty sensor was the issue and that it was very common.
The contact owns 2012 chrysler 200. The contact stated that the accelerator pedal failed to respond. The vehicle was taken to a dealer where the technician was unable to duplicate the failure. The vehicle was not repaired.the manufacturer was made aware of the failure. The failure mileage was 27,000.
I was driving my new chrysler 2003.6l approximately 25-30 mph pressed the gas pedal and had no response.engine was dead, the steering locked-up causing the vehicle to pull right running off the road.fortunately, my two children and myself were not harmed.i am extremely disappointed/angry that my children were put into this situation.i believe this is a an unsafe vehicle and investigation should take place.
2.4 liter 2011 chrysler 200.when slowing then accelerating in left turn lanes and turn abouts, the 200 will often stall for a second or two, then proceed.seems to especially happen when attempting to increase speed quickly to enter traffic.the engine will stall and become unresponsive for a second or two before responding again.the entire process is that i brake and slow for the turn or to enter a round about, when there is an opening, i accelerate, the 200 will speed up as expected, then the engine will suddenly stall and become unresponsive for 1-2 seconds, then resume as normal.this has been unsettling a couple of times.this seems to occur when turning and accelerating.i do not have any issues when accelerating in a straight line.the second speed issue is that the 200 is slow to stop revving when accelerating.on several occasions upon acceleration, when i lifted my foot off of the accelerator, the engine kept revving for a couple of seconds and the car kept speeding up.this has not caused any safety issues.it only happens when i accelerate quickly.when driving normal, this issue does not occur.
Purchased a used chrysler 200 in february 2017 at 87,xxx mi. It is now june 2017 and 3 times in the last 3 days my car has suddenly died. The first time i was slowing down and made a right turn and upon accelerating it died, dash lights illuminated, quickly tried to restart and was unsuccessful with just nothing happening when turning key. Took key out of ignition and retried and started right up.next day i was again slowing down and making a right turn and bam same thing same details. 3rd incident i was driving straight and the car stalled this time i was doing about 15 mph and the steering locked up, quickly took key out and restarted. Engine light was on and diagnosed as crankshaft position sensor malfunction. Replaced the sensor and have only driven for short distance as the first 2 times this happened were terrifying enough. After hours of online research i've found this is common and just being neglected. Chrysler fix this issue before someone gets seriously injured
The contact owns a 2012 chrysler 200. The contact stated that the transmission failed to shift gear without warning. The contact mentioned that sometimes the shift lever would become stuck to the first gear and the vehicle failed to accelerate over 30 mph. The vehicle was taken to a dealer. The technician diagnosed that the power control module and valve body were defective and needed to be replaced. The vehicle was repaired but the failure recurred. The manufacturer was notified of the failure. The failure mileage was 13,500.
When driving my vehicle i had three lights to come on which resulted in having to take my car to have a diganostic test, the out come was the throttle position censor in which i have never had any problems before from any of my chrysler vehicle andthe repairman said this is a dealer defect. I am very disappointed that i am going through and ordeal since i have owned many chrylsers with no problem.
The contact owns a 2012 chrysler 200. The contact stated that while driving approximately 8 mph down a hill in first gear, the rpms increased to approximately 4500 and the vehicle accelerated on its own to approximately 35 mph. The contact depressed the brake pedal with excessive force and was able to stop the vehicle by placing it in neutral. The vehicle was not taken to the dealer for a diagnostic test. The vehicle was not repaired. The approximate failure mileage was 19,000.
In traffic, steering wheel tightened up and all interior lights were off. Tried to brake but no response, shifted into neutral restarted the car and it turned back on. Seemed to mess up the shifter a little in the process, as well as almost hitting the car in front of me. Probably going about 10-15 mph, and i was lucky to throw the car in neutral and restart otherwise i would of floated into an accident.
I was merging on i-271s when suddenly check engine light came on and my car came to a complete stop (the engine was still running).i was not able to accelerate so i slowly maneuvered my car onto the shoulder. I turned off the car and re-started,but i couldn't still accelerate.i had the car towed 25 miles to a trusted mechanic.the next day i was told my him that the crankshaft position sensor was bad and needed to be replaced.i believe that the sensor issue is serious.without warning my car came to a sudden stop on major highway.by sheer luck i wasn't rear-ended and i didn't lose my life, or worse, my kids.
The contact owns a 2012 chrysler 200. While driving 50 mph with the accelerator pedal depressed, the speed reduced independently to 5 mph. The vehicle stalled and the throttle body and abs warning indicators illuminated. The vehicle was able to restart on the first attempt. The vehicle was not diagnosed or repaired. The manufacturer was made aware of the failure. The failure mileage was 84,000.
Today, while on the interstate traveling at 60mph, attempted to accelerate and car would not accelerate. Could hear the engine trying to accelerate but the car kept slowing down. Did not see any lights (engine) light up on the dash to indicate a problem. Pulled into emergency lane, stopped and turned engine off; restarted car and it has not occurred again today.
The car will almost stall, randomly, when stopped at a stop sign or light. It has now started to act like it is going to stall when we start it. The car hesitates, randomly, when you go to accelerate.this has happened to us many times. Entering the interstate it acts like it stumbles before it will respond.we have pulled out onto a busy street where acceleration is a necessity and the car hesitates and almost caused an accident.most recently, switching lanes on the interstate we lifted our foot off accl. To allow a car to pass us when we went to accelerate again the car would not respond, a car came up on us in our lane and almost rear ended us. (this was on the way to the dealership for the problem) the dealer has been unable to duplicate the issue and nothing was recorded on the computer. Many complaints about this issue on chrysler 200 forums. We have had a blk box installed and no feed back from dealer was provided even when requested in writing and verbally. We have an attorney, chrysler has put a low value on the complaint and we are not going to settle case at this time. I hope we do not have an accident while collecting data!
The contact owns a 2012 chrysler 200. When the accelerator pedal was depressed, the vehicle failed to accelerate. In addition, the vehicle hesitated and stalled without warning. The vehicle was able to be restarted, but the failure recurred. The dealer was unable to diagnose the cause of the failure. The manufacturer was not notified. The approximate failure mileage was 67,000.
Stopped at a red light, up until then car was driving fine, made a left turn and the 200 loss power and stalled out. The etc light and traction control light came on out the corner of my eye, next thing i know i was plowed into by another car. After doing more research, i have seen this problem come up time after time. The electronic throttle actually has plastic gears, plastic gears that control the opening of the throttle valve im sure those teeth will wear out on nearly every car and cause problems.
While driving down the road the etc light came on and the traction light came onand the car will not accelerate. I was able to park the car and when i restarted it that was a very rough idle and the check engine light the etc light and the traction light are all on.
The contact owns a 2012 chrysler 200. While driving approximately 65 mph, the vehicle failed to accelerate. When the accelerator pedal was depressed, the vehicle began to decelerate. The failure occurred on several occasions. The contact stated that the failure occurred after the heater blower failed to blow heat out of the passenger side vents. The vehicle was taken to an independent mechanic who was unable to determine the cause of the failures. The local dealer (jim riehl's friendly chrysler jeep in sterling heights, mi) was notified. The vehicle was not repaired. The manufacturer was not notified of the failure. The failure mileage was 87,000.
"takata recall" my air bag light is on in the dash board my car was already at the dealership for another issue the agent informed me the airbag modular has failed i informed the agent there is a recall for the tipm.a defective tipm can causeair bags not to inflate and other major issues.the dealership want to charge me 429.00 to fix.
The contact owns a 2012 chrysler 200. While driving 40 mph, the electronic throttle control light illuminated. The vehicle slowed to 20 mph and went into limp mode. The vehicle was taken to the dealer to be diagnosed. The contact was informed that the electronic throttle control module needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure. The approximate failure mileage was 94,200. Udated 07/26/16*lj.....updated 08/01/16 consumer stated the vehicle ceased to accelerate on a busy street. Consumer was informed that every sensor in the electronic system was malfunctioning, which caused dealer to be unable to accurately diagnose the problem. Repairs not covered by warranty. Consumer noted chrysler issued a recall for the same exact issue on 2015 chrysler 200 model.updated 06/13/18
The contact owns a 2012 chrysler 200. While driving 50 mph, the vehicle accelerated independently, the rpm gauge increased from 0-4, and the speedometer gauge failed to display the actual speed. The failure recurred numerous times. In addition, the contact stated that the vehicle failed to start. The vehicle was taken to a dealer where the battery was replaced. The manufacturer was not notified of the failure. The approximate failure mileage was 99,000.
Transmission goes in to limp mode,does not go over 30 miles jerking speeding up and slowing down, won't start and check engine light comes on goes off.
When purchased this car, noticed that it pulled severly to the left,spoke to dealer ship and they stated that it was normal for front wheel drives to do so.so i continued to drive this car but always having to be on alert when driving on highway if car was going to jerk off road. This car handles horrible! i do not feel safe in this vehicle and do not feel if any control was lost, that i would be able to regain control due to this.the dealership has denied that i have ever brought this up, but when my brakes started squealing around 7000.00 mile i then brought it up again and they told me i needed a front end alignment and new brakes! ok i just bought the car... I told them no, how could that be.well since then my car has had to have the cylander replaced and they have addressed the jerking with a front end alignment which by the way did not do anything. It still is hard to control and could only do 30 mile an hr in snow before it would loose control. I have more complaints and have addressed chrysler to no avail. They just tell me its the make of the car and that my brakes squealing are because asbestos is no longer in brakes. I told them that i was not born yesterday and have driven more cars than this and never have had this problem. They offered me an extended warrenty and stated that was all anyone could do .i am a very unhappy customer and becasue i am in a lease i can not get out of this car. Only when it crashes will anyone maybe do anything about this.i am seeking the state attorney in idaho to see if they can help resolve this issue .
The contact owns a 2012 chrysler 200. While attempting to drive the vehicle, the contact noticed that the heater failed to function on the passenger and middle vents. The failure caused the windshield to freeze. The vehicle was not taken to the dealer or an independent mechanic to determine the cause of the failure. The vehicle was not repaired. The manufacturer was not notified of the failure. The vin was unknown. The approximate failure mileage was 60,000.
The contact owns a 2012 chrysler 200. The contact stated that the vent control failed to release heat from the vent on the front passenger side. The failure prevented the windows from defrosting in inclement weather. The vehicle was taken to yark chrysler jeep dodge ram (6019 central ave, toledo, oh 43615, (419) 877-7712) to be diagnosed. The manufacturer was notified of the failure. The vin and failure mileage were not available.
The contact owns a 2012 chrysler 200. The contact stated that while driving 30 mph, he opened the rear driver side window and began to hear a high pitched screeching noise. The contact also stated that the noise created a lot of pressure on his ear drums. The vehicle was not taken to have the failure diagnosed or repaired. The manufacturer was made aware of the failure and no further assistance was provided. The failure mileage was 500.
The contact owns a 2012 chrysler 200. The contact stated that there was no heat coming from the front passenger side vent and the defroster also failed to function on the front passenger side. The dealer (landmark dodge chrysler jeep ram,1900 s noland rd, independence, mo 64055, 1-(816) 833-2100) was contacted for routine servicing and they flushed the radiator, but the failure continued. The manufacturer was contacted. The vehicle was not repaired. The approximate failure mileage was 130,000.
The contact owns a 2012 chrysler 200 convertible. While turning the heat on in the vehicle. The passenger side blew cool air instead of hot. The vehicle was not taken to the dealer. The vehicle was not diagnosed or repaired. The manufacturer was not contacted. The failure mileage was 61,000.
Heater and defroster fail on passenger side of vehicle.this causes the driver to not be able to see.the cause of this failure is do to faulty fluid/design by chrysler.this is a major safety issues.
The heat on the passenger side is no longer working and therefore the windows on the passenger side will not defrost. After performing some research online it appears that this is an issue with the heater core that chrysler knows about.
The wipers now only work on high there no longer is any other speeds.when you turn them off they just stop where ever there at, at the time. Tipm faulty .car has 80,000 km.
The heater core become clogged preventing air flow, to defrost the windshield on the passenger side of the car. I even did the regular scheduled coolant flushes to prevent this from happening, and it still happened.it becomes dangerous as the vehicle heater core becomes so backed up that not even a full heater core flush can save it. I have read on line that this is a issue that happens to a lot chrysler vehicles, and it sounds as if it has to do a lot to with the car was manufactured through the sand cast process. The car has overheated also has a hard time keeping the car warm because of the clogged heater core. This problem has effected many of the 200 vehicles , and im surprised that a resolve has not be brought out yet., it almost got me in a accident on the turnpike because i couldn't defrost the windows.
There is low heat output from the heater vents due to the heater core plugging up with "sludge" as chrysler calls it. There is a chrysler star technical assistance hotline case, number s1207000008 explaining heater core restriction due to sludge causing poor heater system performance. It is a well known problem with a large number of chrysler 200 and dodge avengers which i am sure can be verified by chrysler. I believe it should be a recall, or at least an extended warranty issue. The star case states to replace the heater core, radiator, radiator cap and reverse flush the entire system if the customer complaint can be verified by the technician, however it does not explain the actual cause of the sludge. The symptom first noticed is little or no heat on the passenger side of the vehicle, then progressively lower heat output the more plugged the heater core becomes as time goes on. I believe in cold climates this could also cause the windshield to stay iced over, or become iced over as you drive down the road due to wind chill factor of the vehicle speed. It could also be aggravated by the fact that the air conditioner runs with the heater on defrost ( to dry interior air in order to de-fog the windshield in humid or rainy weather) which further cools the already cold air coming from the defroster vent if the heater core eventually becomes completely plugged. In hot climates, the heater core still plugs up, however the customer may never notice the symptoms. I also happen to be chrysler academy master certified in all core curriculum,powertrain, electrical and chassis. Ase master and advanced level certified (a1 through a9 and l1) ase certified parts specialist(p2)and service consultant(c1) and i have an aos degree in automotive trades from suny alfred. New york state dmv certifications( f.e.e.t, s.t.e.p, c.a.p.s, f.i.s.t.).credentials can be verified upon request.
Wipers only work on high. Wiper motor shorted to ground causing internal collateral damage to tipm. Removed and replaced wiper motor. Removed and replaced tipm and updated software.
My 2012 chrysler 200 ; 2.4l engine has no heat on the passenger side - no heat on defroster, floor, or out vents.dealer said there is build up in cooling system (star case #1207000008) ; recommends replacing heater core, radiator, thermostats, engine oil cooler -est $2000.00 repair.no heat during defrosting causing windshield fogging and reduced visibility during cold weather.this started jan 2, 2017 and is ongoing.
Takata recallno heat on passenger side, blows cold air. Unable to defrost passenger side of windshield. Chrysler service advised that heatercore plugged, need to replace heater core, radiator, engine oil cooler & thermostat.had all replaced, at a cost of $2200. One year later, same problem, no heat passenger side.
Suddenly and with out warning, while driving in light rain conditions, the windshield wipers failed to operate on any speed setting but high. They also would not park when shut off, which necessitated timing the shut off. The vehicle was diagnosed at a local dealer as needing a new tipm. Total cost $1638.50.
Visibility on the passenger side of windshield is impaired (non existent) the defroster on the passenger side of the car no longer blows warm air instead cold air is being produced from the windshield vent and also heat from middle and side registers on the passenger side. Dangerous for winters in ny.ridiculous amounts of complaints registered regarding this problem and many costly solutions not resolving the issue.this needs to be a recall from chrysler.
With the wipers on, all of a sudden, they will start to skitter across the windshield then stop and start again then speed up and slow down.if they are turned off the wipers will continue to run then finally stop halfway in the glass then finally goto the resting position.this occurs randomly at any time of year.i have had the wiper switch replaced hoping that the relay in the switch assembly was the issue but the problem still persists.
There was cold air coming out of the passenger side air vents. This would take a significant amount of time to defrost the windows. The air was about as cold as the static outside air temperature. The drivers side air would eventually heat up the entire windshield to safely drive. However, if it was below 20f outside the drivers side heat would not be hot enough to keep the passenger side window defogged. This posed a lot of safety concerns cursing along the highway. Later, this was deemed to be a clogged/faulty passenger side heater-core which had to be replaced. After this was replaced the passenger side air is about as hot as the drivers side now. The defrost times are equal on both sides during cold starts and visibility is back to normal. The mechanic recommends doing an annual cooling flush to prevent the heater core from becoming faulty in the future. Although they said even that isn't a guarantee to solve the issue entirely. Apparently the heater core has a critical design issue.
Passenger windshield visibility do to heater core not giving heat at passenger side clogged at about 70k miles dangerous to me and oncoming traffic an accident waiting to happen.
The contact owns a 2012 chrysler 200. While driving approximately 10 mph and activating the right turn signal, the windshield wipers engaged automatically. The failure recurred every time the turn signals were used. In addition, the heater would blow hot air through the driver side vents and cold air through the passenger side vents. The vehicle was taken to a dealer, but was not repaired. The manufacturer was not notified of the failures. The vin was unknown. The approximate failure mileage was 76,000.
My vehicle has roughly 54,000 miles. The heat does not work on the passenger side of the vehicle and is progressively becoming colder on the driver side of the vehicle. The car will not reach a warm enough temperature to be comfortable or to adequately defrost the windshield. This is a known issue to chrysler and should be recalled. The parts involved are the heater core and radiator.
"takata recall"when it is cold the defrost won't work and the passenger side of the car is extremely cold.
The entire heating system for the passenger side does not work. I can be stationary or on a roadtrip. I'm only able to defrost a small part of my windshield making it very unsafe to drive in the winter. I have seen other people with this issue that say it is a manufacture problem and costs around $1,700 to fix. That is unacceptable.
The passenger side heat is not working, this appears to be a very common issue with this make and model.the issue get worst overtime as it is now affecting my ability to properly defrost my padsanger side windshield as well as the passenger side window which is causing a safety concern due limiting my visibility .this is driving hazard to me and other drivers during the winter.
Passenger side pushes out cold air, terrible to drive in and uncomfortable. Battery has been replaced 4 times in the last 2 years. Alternator as well. While driving to work, my windshield frosted over from being so cold and i had to veer off the road to avoid getting into an accident.
2012 chrysler 200 convertible heat fails to defrost window causing total visibility loss and inability to see out of windshield.lack of heat does not allow for safe operation of vehicle.this occurs when vehicle is running.the car can not warm up enough to defrost windshield. No heat coming from defrost or vents. Blows cold air. This occurs when driving or stationary. Can not see! dangerous!
Heater blows out cold air i have no heat i cant defrost car windows to see .this has been happening since 2016 jan i have replaced actuvator blendoor 3 times ....thermostat 2 of them... Flushed the heater core .....found out i have a sludge or blockage in my radiator and heatercore plus need radiator cap 2500 to fix ? its a 20
The contact owns a 2012 chrysler 200. The contact stated that while driving at a low speed, the wind shield wipers were activated but failed to function. The vehicle was taken to a dealer who diagnosed that that totally integrated power module (tipm)needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was 45,300.
No heat/ defrost passenger side. Will not clear frost/ fog on passenger side windshield. Apparent known problem with sludge build up in heater core allegedly caused by component in coolant.
My horn started honking on it own.i first noticed it when i was outside the car and had not touched it, the horn started honking.i got in the car and it stopped.every time i drive the car the horn honks on its own, sometimes long honks other times brief.the next thingit started raining and the wipers would not work properly they would swipe halfway and stop, only working when on high.finally i was driving home and the car stopped in traffic.i sat for a few minutes and started it and it would stop after moving for about an inch.the car stopped three or four times and finally i was able to drive the 2 or 3 miles to my home and park.
The contact owns a 2012 chrysler 200. The contact stated that the air conditioner unit failed. The vehicle was taken to the dealer to be diagnosed. The contact was informed that the recirculation door alternator for the defrost and air conditioning unit failed. The vehicle was repaired twice, but the failure recurred. The manufacturer was notified. The approximate failure mileage was 40,000....updated 01/23/17 consumer stated at 40,000 and 106,000 miles clicking on passenger side started both times replaced the recirculation and alternator. Updated 7/13/18 consumer stated this will be the 4th failure of this part on this car and the second time that the radiator system has been either partially or entirely replaced in this vehicle.
The contact owns a 2012 chrysler 200. While driving various speeds, the contact noticed that the heater failed to function on the front passenger side vent. The failure prevented the windows from defrosting in inclement weather. The failure occurred without warning. The vehicle was not diagnosed or repaired. The dealer and manufacturer were not notified. The approximate failure mileage was 90,000. The vin was not available.
The contact owns a 2012 chrysler 200. The contact stated that the heat and defroster were not working specifically on the passenger side, which affected the contact's visibility while driving. The contact also noticed a fuel odor coming from the heating unit when it was activated. The contact called the dealer (barbera autoland, 7810 e roosevelt blvd, philadelphia, pa 19152, (215) 333-3700) and was informed that there was no recall. The contact was advised to call the manufacturer. The manufacturer agreed with the dealer and stated that there was an assistance program to help pay for the repairs, if the contact was eligible. The manufacturer advised the contact to call nhtsa. The failure mileage was 60,000.
Passenger side heating and defrost not working and barely working on driver side. Will not defrost causing trouble with visibility... There have been numerous complaints about this very same issue on "carcomplaints.com" the issue became noticeable when it state to get cold in november and december of 2017 around 68,000 miles
While driving the vehicle in 30 degree weather, started smelling something very bad coming from hvac system and windows became very foggy. I had to roll the windows down with the defrost on in order to see. Vision was still impaired. After letting it sit, a film appeared on the inside of the windshield, which is hard to remove. Further impairing vision.prior to this, heat on the passenger side stopped working so the passenger side of the windshield would not defrost quickly. Currently have it in the shop. They are guessing it's the heater core, a known issue with this vehicle. Estimated cost starting at $900.
The contact owns a 2012 chrysler 200. The contact stated that the heat and defroster stopped working. The vehicle was taken to landmark dodge chrysler jeep ram (1900 s noland rd, independence, mo 64055) four times, and each time the heater cooler was replaced. The manufacturer was contacted and did not assist. The vehicle was not diagnosed or repaired. The failure mileage was 78,000.
The contact owns a 2012 chrysler 200. The contact stated that the defroster failed to operate as intended. The vehicle was taken to glendale chrysler (10070 manchester rd, st louis, mo 63122) where it was diagnosed that the engine core radiator, heater core, and radiator cap needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure and did not assist. The vin and failure mileage were unknown.
My windshield wipers just stopped in the middle of a storm & will now only come onhigh.
The heater core gets clogged up and your windshield visibility will not be cear. Thia will cause unsafe driving measures.no heat my car blows out vool air only.
The contact owns a 2012 chrysler 200. When the contact attempted to drive the vehicle, the heater on the front passenger side failed to function and prevented the passenger side window from defrosting. The failure occurred without warning. The vehicle was not taken to the dealer. The vehicle was not diagnosed or repaired. The manufacturer was not contacted. The approximate failure mileage was 47,000.
The car had only 35,000 miles when the issue started. The passenger heat is cold, and the defrost will not work, while the driver's side gets warm, and will defrost a small amount of the driver side windshield, and nothing on the side windows. This issue is a hazard for visibility in the winter. I have researched the matter to finds this is a common issue with the chrysler 200 and has a repair bill of $1500 as the passenger side has a blockage or clog in the system.
The contact owns a 2012 chrysler 200. The contact stated that the defrost system did not function properly. The contact mentioned that the vehicle had to be flushed every year in order for the defroster to work. The vehicle was not taken to a dealer or an independent mechanic for diagnostic testing or repairs. The manufacturer was not made aware of the failure. The vin was not available. The failure mileage was approximately 70,000. Consumer stated thermostat was replaced. Vin not available
While driving car shut off. Also windshield wipers not working properly.
The defroster only blows cold air. No matter what the temperature or fan are set at. Thus making visibility when the windshield fogs up very poor. By the research that i have done it is because during the manufacturing process pin hole leaks were discovered in the radiator instead of replacing the affected part they put a stop leak formula in the heating system. This was an improper product and caused a sludge build up which irreparably destroyed the heater core. In addition to the defroster problem hot air only comes out of the drivers side vents while cols air comes out of the passenger side vents,
Passenger side does not have any heat coming out of the vents, or defrosters. Only the far driver side produces small amount of warmth. Being that i live in wisconsin, it has become hazardous for me to drive my vehicle in the winter for obvious reasons. Not being able to unfog, or defrost your windows is unbelievably dangerous! aside from the dangers of driving at times with only half of a clear windshield, my passengers and i freeze inside the vehicle during the winter! the only way to clear the windshield and passenger window is to periodically open the windows while driving, which only makes the inside temperature that much more unbearable.
Both the dash and passenger window defrosters on the passenger side of the car blows cold air.this is not just a comfort issue.the restricted visibility is very dangerous.i wish i would have known before i purchased this vehicle.there are hundreds of complaints online and the cost to fix is ridiculous. This needs to be a recall from chrysler.
The contact owns a 2012 chrysler 200. Upon starting and driving the vehicle for a while, the heater ventilation would circulate hot air on the driver side and cold air on the passenger side. Due to the failure, the defogger on the passenger side of the vehicle was not operational and prevented the contact from seeing out the windshield. There were no warning indicators illuminated. The vehicle was not taken to an independent mechanic or dealer for diagnostic testing or repairs. The manufacturer was not notified. The vin was unknown. The failure mileage was approximately 80,000.
Defrost does not work and this impairs visibility.cannot drive car when windshield fogs.dealer reports that the heater core needs to be replaced at a cost of $2000. This is widespread among this model and similar models according to computer search.
Partial defrost. The coolant has something in it (from the factory) causing the heater core to plug up and then there is no defrost on the passenger side of the car. Thus impairing the visibility. My car has 24,000. Miles. Chrysler is aware of this problem. There was a star report sent to dealers in 2012. That report number is star case s1207000008.
Defrost doesn't work.dealership calls for replacing radiator, heater core and oil cooler due to sludge build-up/clogging in coolant/heating system. This appears to be due to an incompatibility between the coolant used by chrysler and the chemicals/oils used in the manufacture of the engine system. This is 100% a manufacturing defect and the dealer & manufacturer are unwilling to replace. Fairly common problem with the 2012/2013 chrysler 200, regardless of engine type. This is a safety concern as the windshield can become fogged very quickly while driving under the right conditions (damp weather) and without warning, posing a safety hazard. Started about one year ago.
Known issue with heater core results in not only comfort issues, but driving hazard, as the defroster is also impacted. Heat does not flow from passenger side defroster, resulting in lack of visibility. This has happened more than one time while driving, including instances of total blockage of view on right side of windshield.
The contact owns a 2012 chrysler 200. While driving unknown speeds, cold air blew out of the passenger side vent without warning. The contact called a local dealer (bob caldwell chrysler jeep dodge ram, 1888 morse rd, columbus, oh 43229) and was informed to schedule a service appointment. The vehicle was not diagnosed or repaired. The manufacturer was not notified. The failure mileage was 56,000.the consumer stated no heat to defrost windshield, repairs being made by dealer, but consumer is paying out of pocket for the repairs.
The contact owns a 2012 chrysler 200. The contact stated that the passenger side heat blower had malfunctioned and the passenger side windshield would not defrost. The vehicle was taken to an independent mechanic who was unable to diagnose the cause of the failure. The manufacturer was not notified of the failure. The failure mileage was 90,000.
Heat stopped working on passenger side. Defrosting is more difficult being that the air is not warm in cold temperatures. Prior to the heat not working on the passenger side the a/c stopped getting cold too. (it was getting cold only on the drivers side)
Windshield wipers quit working. Only wipe on high. Took into dealer to repair, they replaced the wiper motor. Did not fix problem, they then ran codes to tell me it is the tipm. My extended warranty company said they will not cover, problem still not fixed.
The passenger side of my defrost/vents does not work--it remains cold even on high heat and driver side hot. The windshield and passenger window remain foggy or ice covered, or after removing the fog or ice it rebuilds fog or ice while traveling on highways while snowing, extremely limiting visibility. This winter has been quite difficult to drive safely due to this condition.
Complaint: passenger seat belt gets stuck when buckled. You have to pull really hard to release the buckle. If i were to get in a wreck i could not get a passenger out of my passenger seat because its too hard to unbuckle.this occurs when car is moving and stationary. Heater problems: my passenger side heat is not working it is blowing cold air and will not defrost the passenger side. Only the driver side right vent blows warm air. This issue occurs when car is stationary and moving.
The vehicle has lost most of its heating capabilities and will not defrost the windshield. This is extremely dangerous as we live in a cold climate during the winter and could cause an accident as well as causing the driver to be very uncomfortable while driving. I have read up on numerous complaints of this and i cannot believe there hasn't been a recall submitted by chrysler. I even had a past chrysler mechanic inform me that when he was working for a chrysler dealership that the dealership received a letter informing them that they would start to see this problem occuring with these vehicles. Unbelievable! and yet no recall has been issued? this needs to be addressed for serious safety concerns before people are killed if it hasn't happened already.
2012 chrysler 200 heater issue.vehicle will not warm on passenger side preventing defogger to reduce ice or snow from windshield.the vehicle was taken to chrysler dealership and after several attempts to remove sludge from the radiator and heater core the heater still will not maintain heat to the passenger side which is a safety issue in keeping the windshield clear of ice or snow. Dealership indicated that heater core, radiator and coolant reservoir will all need to be replaced.in reading various forms its known that chrysler uses some type of chemical to plug any pin holes in the radiator and this product is causing a sludge in the system and creating the problem.chrysler will not or indicated after calling, they will not pay the $1700 cost of the repairs that were created during manufacturing.
The passengerside stopped working no heat. Took the car to dealership and they flushed the system with chemicaland coolant a lot of junk came out. That didn't work now dealership says heater core and radiator needs replaced $1700. I research this and there has been a problem with 2012 with the same problem. There should be a recall.
In march 2014 owner noted a problem with the hvac system - no heat was delivered to the passenger side air vents or heater vents in cold weather. During routine oil change mechanic noted severe discoloration of engine coolant and buildup up sludge in coolant expansion tank. Took vehicle to dealer for diagnosis. Dealer stated that the coolant had been contaminated with the addition of the wrong type of coolant. Per chrysler star # s1207000008, dealer flushed coolant system multiple times and commented that if that didn't work they would have to replace the heater core, radiator, oil cooler, and expansion tank. When repairs were completed owner noted that the temperature output from the air and heater vents was 20 degrees lower on the passenger side than the driver side. Dealer stated that repairs were complete. Owner is in process of contacting chrysler to have heater core and radiator replaced.
The passenger side heat is not working, this appears to be a very common issue with this make and model.the issue get worst overtime as it is now affecting my ability to properly defrost my padsanger side windshield as well as the passenger side window which is causing a safety concern due limiting my visibility .this is driving hazard to me and other drivers during the winter.
Passenger side air blowing cold air while in high heatgoogled it seems to be major issue in these vehicles chrysler knows about it says it's a chemical the addto coolant plugging heater core.
The contact owns a 2012 chrysler 200. When the contact activated the defroster, the vehicle blew out cold air on the front passenger side and hot air on the front driver's side without warning. The vehicle was not taken to the dealer. The vehicle was not diagnosed or repaired. The manufacturer stated that they never heard of the failure before and asked the contact to take the vehicle to the dealer. The approximate failure mileage was 58,000.
The contact owns a 2012 chrysler 200. The contact stated that passenger side blower failed to blow hot air which caused the defroster to become inoperable. As a result, there was limited visibility for the driver. The vehicle was taken to pat clemmons inc located at 1720 s. Marshall st. Boone ia, (515)432-5150 to be diagnosed. The contact was informed that the heater coil needed to be replaced. The vehicle was not repaired. The manufacturer was not notified of the failure. The failure mileage was 90,000.
The contact owns a 2012 chrysler 200. The contact stated that the vehicle was not emitting heat and the defroster failed to defrost the windows. The vehicle was taken to an independent mechanic where it was diagnosed that the heater core and the radiator needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure. The approximate failure mileage was 60,000.
The contact owns a 2012 chrysler 200. While the vehicle was stationary, the defroster stopped working in a snow storm and the contact could not clear ice/snow from the windshield in order to see properly. The vehicle was not repaired. The manufacturer was made aware of the failure. The failure mileage was 81,000.
The right side (passenger side) of vehicle gets very little heat. This caused the entire car to be cold. The defrost does not melt ice on windshield.this first happened when the car was 11 month old.the dealer replaced the radiator, heater core and cleaned the block.he said these were full of sludge. Today, march 2015)at 34017 miles, i picked up the car from the dealer after complaining of the same lack of heat and the same was reported,replaced radiator,heater core, oil filter cooler and flush cooling system.also stated on the repair invoice "performed test and repair per star case [xxx]".this is apparently an account to charge the repair back to chrylser.chrysler knows of this problem.the service advisor told me that someone at manufacturing plant added a sealant to stop leaks.he said it is well known not to use this sealant because of the problems it will eventually cause in the system.this has been repaired twice, i have no reason to believe that it will not happen again.it has been paid by warranty but some day it will be out of warranty and i will not be the one paying for it!!!!chrysler must be held accountable for this and make a permanent correction to this problem.information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6).
When i turn on the heat, the passenger side vents blow cold air. This is a problem to drive using my air/heat because it's draining my coolant. This causes my temperature gage to rise. This happens regardless of my car being stable or in motion. This, at times, also causes my windshield to become foggy.
The contact owns a 2012 chrysler 200. The contact stated that the defrost system did not function properly. The contact mentioned that the vehicle had to be flushed every year in order for the defroster to work. The vehicle was not taken to a dealer or an independent mechanic for diagnostic testing or repairs. The manufacturer was not made aware of the failure. The vin was not available. The failure mileage was approximately 70,000. Consumer stated thermostat was replaced. Vin not available
The contact owns a 2012 chrysler 200. While driving approximately 65 mph, the vehicle failed to accelerate. When the accelerator pedal was depressed, the vehicle began to decelerate. The failure occurred on several occasions. The contact stated that the failure occurred after the heater blower failed to blow heat out of the passenger side vents. The vehicle was taken to an independent mechanic who was unable to determine the cause of the failures. The local dealer (jim riehl's friendly chrysler jeep in sterling heights, mi) was notified. The vehicle was not repaired. The manufacturer was not notified of the failure. The failure mileage was 87,000.
The contact owns a 2012 chrysler 200. While driving 60 mph, the contact realized that the passenger side of the vehicle became cold. While the defroster was activated, the contact realized that only the driver's side was defrosting and not the passenger side. While the vehicle was stationary, the passenger side began to defrost. While the vehicle was in motion, the passenger side became cold. The dealer (east gate chrysler, 500 n shadeland ave, indianapolis, in) diagnosed that the heater core failed. The vehicle was not repaired. There were no recalls associated with the vin. The manufacturer was not notified. The failure mileage was 100,000.
The contact owns a 2012 chrysler 200. When the contact attempted to drive the vehicle, the heater on the front passenger side failed to function and prevented the passenger side window from defrosting. The vehicle was taken to doug marine motors (1120 clinton ave, washington ct house in oh 43160) where it was diagnosed that the heater core needed to be replaced. The vehicle was not repaired due to the repair fees. The manufacturer was contacted and did not assist. The vin was unknown. The approximate failure mileage was 60,000.
The contact owns a 2012 chrysler 200. The contact stated that the vehicle would not generate heat. The failure occurred without warning. The vehicle was taken to the dealer where it was diagnosed that the heater core malfunctioned and needed to be replaced. The vehicle was repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 54,000....updated 05/19/17
The contact owns a 2012 chrysler 200. The contact stated that the defogger on the front passenger side malfunctioned and prevented the contact from seeing through the windshield. The failure recurred multiple times. The dealer stated that there was a heater core restriction due to sludge, which caused poor heater system performance. The system was flushed, but the failure recurred. The manufacturer was notified of the failure. The approximate failure mileage was 93,000.
The contact owns a 2012 chrysler 200. The contact stated that there was a premature failure with the vent control electronic function. The vent controls failed to generate warm air when the heating function was used. An independent mechanic stated that the heater core needed to be replaced. The vehicle was not inspected by a dealer. The manufacturer was notified of the failure. The vin and failure mileage were not available.
The contact owns a 2012 chrysler 200. While driving 40 mph, the heat and the defroster on the passenger side started to blow cold air. The dealer (town and country jeep chrysler dodge, 3156 hempstead turnpike, levittown, ny 11756) diagnosed that the heater core needed to be replaced. The vehicle was not repaired. The same failure occurred two years later. The manufacturer was not contacted. The failure mileage was 26,000. Updated 8/27/18
The contact owns a 2012 chrysler 200. The contact stated that the heater did not work on the passenger side of the vehicle. There were no warning indicators illuminated. The vehicle was taken to haasz automall of ravenna (4886 oh-59, ravenna, oh 44266) where it was diagnosed that the heater core and the radiator needed to be replaced. The contact was informed to pay a deductible because the vehicle was not purchased at the dealer. The technician also stated that the vehicle was out of warranty. The manufacture was made aware of the failure and stated that the deductible needed to be paid. The vehicle was not repaired. The failure mileage was approximately 54,500.
The contact owns a 2012 chrysler 200. The contact stated that passenger side blower failed to blow hot air which caused the defroster to become inoperable. As a result, there was limited visibility for the driver. The vehicle was taken to pat clemmons inc located at 1720 s. Marshall st. Boone ia, (515)432-5150 to be diagnosed. The contact was informed that the heater coil needed to be replaced. The vehicle was not repaired. The manufacturer was not notified of the failure. The failure mileage was 90,000.
The contact owns a 2012 chrysler 200. While the vehicle was stationary, the defroster stopped working in a snow storm and the contact could not clear ice/snow from the windshield in order to see properly. The vehicle was not repaired. The manufacturer was made aware of the failure. The failure mileage was 81,000.
The contact owns a 2012 chrysler 200. While driving approximately 35 mph, the heater and the front passenger side defroster failed to function when activated. In addition, the transmission jerked while shifting from park into the reverse position on numerous times. The vehicle was not diagnosed or repaired. The manufacturer was notified of the issue. The approximate failure mileage was 56,000.
The contact owns a 2012 chrysler 200. The contact stated that the heater core malfunctioned. The vehicle was taken to the kernersville chrysler dodge jeep ram dealer (950 nc-66, kernersville, nc) where it was diagnosed that the heater core failed. The vehicle was repaired, but the failure recurred at approximately 72,000 miles. The manufacturer was notified of the failure. The vin was unknown. The approximate failure mileage was 19,000.
Purchase new off the chrysler dealer lot april 2012.there are three knobs that control the heating and cooling in the car when the blower is turned to a low setting it will blow hot air regardless of temperature that is selected for example if it is sitting at 66degrees it will blow extremely hot air and only if the blower is set to max will it eventually cool down to the selected temperature. Once the cooler temperature is acquired, if the blower is turned down it will eventually go back to blowing only really hot air regardless of temperature setting.
Replaced disc breaks pads 3 times last year and 2 times this year, the rubber boot inside the break caliber melted and the rear breaks sometimes smokes, now front break pedal goes towards the flow andwith clucking noise, andtbe abs break light is onwhile i was driving..
2012 chrysler 200.at 21,000 miles we noticed a loud muffler type noise coming from right rear.thought it was either exhaust or muffler.had it checked out and diagnosis is failure to the right rear hub bearing which need to be replaced.i noticed that there were other recalls in 2012 for this part but not the chrysler 200.
When backing up from a parking place the first time it happened in the latter part of april 2013, we heard this loud screeching noise coming from what we thought to be the front wheels . I then took the car to the dealership told the service person about it, he then said all cars have been doing it because of the dust storms in the area . The noise has been getting louder and louder it's embarrassing any more to back up ! who would think such a nice and beautiful car would be emitting such a terrible noise. Even my elderly dad has noticed it every time i pick him up and he said what a shame it is that this car makes that horrific sound . On 10-22-13 i reported this problem again our car dealership and asked them to start a case about it and i'd report it to nhtsa. The service manager agrees with me and stated there is a problem with the chrysler 200 cars and that chrysler corp, refuses to admitthere is problem with these cars! don"t buy this car!
Several times since the purchase of my 2012 chrysler 200 touring (3.6 liter v6) i have had steering and control problems with the car. Upon doing my own inspection, i discovered that the tires provided on my 18x7inch, *upgraded* factory rims, are substanitally under rated for the size, weight and power of this vehicle. The tires on the v6 200 with the upgraded wheels have a performance rating of 't,' however after talking to several tire shops and looking a similarly equipped cars, this seems to be an unreasonably low rating for this particular car. It results in sever understeer, harsh cornering, poor brakeing distance, and could result in a blow out. The 4 cylinder version of this same car comes with tires that have a much higher rating. In fact many small family sedans have higer rated tires than the heavy and powerful chrysler 200. Even other cars offered by chrysler group. It seems that only the 200 with the upgraded rims has the under performing tires. To make this problem even worse, under hard acceleration the car will continue to accelerate and raise rpms even after my foot is off the gas pedal. This problem, coupled with the poor performing tires caused the car to skid into a the grass median in a corner. No one was hurt and the car was not damaged.
Read more
