Enter VIN number
Get the most accurate report for the vehicle. Basic information is FREE
Use this form now and GET 20% DISCOUNT for CarVertical reports!




We found the following complaints for CHEVROLET COLORADO (2012)

Read complaints for CHEVROLET COLORADO (2012)


The contact owns a 2012 chevrolet colorado. The contact stated that the air bag warning light remained illuminated. The dealer was unable to reset the air bag warning light. Approximately one week later, the vehicle was parked and a loud pop sound was heard from the vehicle as well as the odor of gun powder. The contact discovered that the front driver's side seat belt retractor exploded. The contact took the vehicle to the dealer where it was diagnosed that the seat belt retractor needed to be replaced. The air bag warning light still needed to be reset. The seat belt retractor was replaced, but the failure recurred and blew a hole into the rear driver side door panel. The vehicle was not repaired a second time. The manufacturer was made aware of the failures. The approximate failure mileage was 76,126.

2012 chevrolet colorado.consumer requests for air bag on-off switch.

The wiring for the airbags runs through a hinge in the extended cab doors. I donā€™t use my rear doors much, but i would say that i use them a normal amount. Regular opening and closing of the door will cause the wires to break, thus making the airbags inoperable. Normal use of doors should not cause your airbags to not work.

About 3 months ago, the airbag light come on, i've checked the codes it gives me and it b0065, b0066, i've checked all the wires and they are in perfect condition, don't know what to do now

2012 chev colorado extended cab (purchased new in 2012).air bag light is on.1st incident aug 2015 (32,000 miles).dealership ran diag scan and pulled code b0092 and repaired wires under passenger seat and cleared code.2nd incident less than 4 months later (34,000 miles) ' dealership cleared code.3rd incident apr. 2016 (37,000 miles).dealership found b0092 set in sdm.an inspection found three wires broken.repaired wiring under passenger seat and cleared code.nothing is being put under the seat.the seat occasionally gets moved forward and backward and the rear passenger door gets open and closed.an internet search reveals same problem in older models.this is definitely a safety issue.the air bag will not inflate if there is an accident.there is obviously a problem with the wires (poor quality or too short causing tension and wear & tear?).a recall should be issued and proper wiring and/or connections corrected.also seems that the cost of repairs ($120 - $140 per incident) should be covered under warranty.

I noticed the airbag warning light on one morning in late october. As i was going out of town, i could not deal with it until i got back, last week. When i took it to the dealer, on saturday, they read the error codes from the airbag module, but could not interpret them, as the specialist was not on duty. I returned it tuesday, (today), and they diagnosed a broken wire in the wiring harness to the left rear door. They replaced it, at a charge of 247.07. They did not cover it under warranty, though the vehicle is only 26 months old, because it is over the 36,000 mile warranty. This type of failure should not be affected by the mileage.i know others with this same failure. I have read numerous similar reports on-line.i use this door every day, to load my wheelchair behind the seat, and i am not looking forward to another failure. Using the door should not cause a safety system failure. Broken and bare wires in any wiring is not safe, and as part of a major safety system, should never happen, and certainly not on such a new vehicle.

Shortly after i bought this truck with 33000 mile on it in june of 2018 the airbag light came on for no apparent reason and has continued to remain lit since that time.since the vehicle is nolonger under warrranty, i have been unable to get it repaired.

Vehicle has only 40,000 miles.the instrument panel warning light for the air bag stayed lit.the wiring harness for the driver's air bag was defective and it cost me $250 to replace the wiring.

Air bag warning light would come on and go off periodically while driving.took to the dealership to have it checked and they stated that there is a short in the harness and the passenger side front post airbag needs to be completely replaced due to this short.the vehicle had 90k miles but it is only 4 years old.the cost of this repair was quoted at $1200.with the vehicle only being 4 years old, chevy needs to stand behind their products and cover this safety item under warranty or consider a recall for any faulty connecters that are part of their air bag safety system.

This truck only has 58,000 miles and the ignition switch went out. I googled it and seen there are tons of others with the same issue. Went to start truck and it wouldn't do anything.

Vehicle randomly does not start and have to sit 10 minutes before it starts up again.is considered a non running vehicle!

Will not start have to take off- post from battery then 10 minutes before it starts. The security light flashes for the 10 minutesbefore it starts.. Ems needs replaced.if i lock the truck after the 3 time it startsthis s(xxx). 2012 chevy. Colorado. It's not the key or switch.

At first, truck showed tps alarm ,then stability alarm ,next ithad the headlights cut out on the highway at night @ 70 mph for 15-30 seconds. It has shown these problems separately and simultaneously at different times. Finallyit manifested a new symptom i would intermittently not crank the engine over even though the battery was at full charge. After repeated trips to the dealer(they said they could not reproduce the problem) with no effect or improvement, a call to chevrolet netted a case number #71-1257538002. As a result of this call( i feel) work was restarted on the vehicle. As of today 12/26/13the chevrolet dealerhas now changed the ignition switch. We shall see.information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6).

I have a 12 month old chevy colorado, bought new.for 9 months, no issues.then in october, it simply won't start.dead battery.i drove it regularly to and from work each day, so it's not from non-use.i took it to service and they said it was a bad battery.they replaced it.about a month later, same thing.dead battery and car won't start, but lights work, radio works.i take it in again, and they can't find a reason.they keep it a week (static) and say there is nothing wrong.but it works when i leave the service department.three weeks later, same thing.car won't start and i'm tired of getting stranded.and i drive it regularly.they take it to another dealers service and they run tests but can't find anything wrong.they call chevy who gives them direction, but chevy doesn't let on that there's a problem.but i go online and find many issues with the same vehicle.since this is the 3rd attempt to fix it, i'm going to pursue the lemon law.

The contact owns a 2012 chevrolet colorado. When the vehicle was started, an unknown warning indicator flashed. The contact had to remove the battery cable, wait a few minutes, reinstall the battery cable, wait an additional few minutes, and then start the vehicle for it to resume normal operation. The contact had not taken the vehicle to a dealer or mechanic to have the vehicle serviced. The manufacturer was not aware of the defect. The vehicle had not been repaired. The failure mileage was 47,000. *dtthe consumer stated he needs a paper copy of evoq.

2012 chevrolet colorado.consumer writes in regards to transmission issues.the consumer stated the vehicle would not start. The vehicle was towed to the dealer. When the consumer called the dealer a couple of days later, he was informed the issue was the transmission. The next week, the consumer was informed, the parts replaced in the transmission were not issue, and after further investigation,the issue was a loose timing chain tensioner. Later in the week, he was informed that the engine was damaged and there may have been a spun bearing that caused the issues. The consumer was then informed the engine needed to replaced, but it would take couple of days to get an approval for the replacement.the authorization finally came through and the dealer proceeded to replace the engine the following week.the consumer was told he could pick the vehicle up on june 1st. However, they wanted to put some additional miles on the truck to confirm everything was in specification.when the consumer arrived at the dealer, he was informed the vehicle overheated and had to be towed back to the dealership.the dealer had the vehicle for two weeks. The consumer stated the vehicle continued to have problems. He stated the truck would idle in a rough manner , and the check engine light illuminated.the consumer stated he checked the codes on the vehicle, and determined they were transmission related. The consumer went to another dealer, who diagnosed the problem as a wiring harness issue and some crimped seals from the first dealerships workmanship. The vehicle was properly repaired and returned to the consumer.

At approximately 350 miles on the truck odometer, the dashboard warning module on my new 2012 chevrolet colorado pickup truck illuminated with "service stab sys".the warning light remained on until i parked the truck. I took the truck to the dealership service center.the service representative at the dealer told me to ignore the warning light.the technician could not find a fault code stored that reflected a stability problem.he told me that no such warning could have illuminated or it would be in the memory of the vehicle??s computer. This warning message: " service stab sys" and the traction warning light now come on repeatedly.in july 2012, while driving at 65 mph on i-40, the same warning illuminated.this was followed immediately by a violent shudder in the steering system and what felt like uneven application of the front brakes for fractions of a second.i pulled over and called onstar who ran a system check.onstar could see the stability system warning was on but no fault code was detected. I took the truck back to the dealership.they told me that there was no fault recorded in the vehicle memory and they could find nothing wrong with the truck and were unable to duplicate the problem.they told me that there was no system or function in the truck or the stability system that could make the truck shudder as i described or that could independently apply braking. This has happened repeatedly, with the shudder also re-occurring.chevrolet and the dealer tell me there is no prior history of problems with the stability system in colorado pickups. Such shuddering in the steering at highway speed cannot be a safe condition.on one occasion onstar detected a code of c-197.the truck is again at the dealership service center who state that they can find nothing wrong with the stability system in the truck.

Abs brakes and stabilitrac lights on dash upon starting, taken to dealer on 11/27/2014, miles 39138, failed again 12/19/2014, miles 39780, and 12/31/2014 for same problem. Truck is still at dealer as of 01/16/2015.after first failure braking was not right, and the truck needs a part that can not seem to be found to date. I believe this truck is unsafe to drive due to the brake issue, and will not keep the truck upon return, but i am fearful that it will be sold to another consumer, and it will be involved in a tragedy.

The "service stability system" warning light comes on and stays on until the vehicle is shut down.it does that repeatedly.the chevrolet dealer, jim cook chevrolet in marion, nc, says they cannot duplicate the light or detect a code and that there is nothing wrong with the vehicle and the light is meaningless and i should disregard it.the user manual states that if this light comes on the vehicle should be immediately parked and taken to the dealer for repairs.this has happened repeatedly for the year i have had the truck.it has been in the shop numerous times.on one occasion, may of 2014, the shop tech at jim cook did see the light come on and he changed the "yaw senor".it did not fix the problem.now the dealer service manager denies that anyone ever saw the light come on at their shop.also, the jim cook manager says that all records they have of serving this truck were sent to gm on orders of the regional gm office and they no longer have any records of serving the truck.the light still comes on and i am afraid to drive the vehicle.chevrolet customer service opened then closed a case on the issue and now tells me i am simply a dissatisfied owner and they will not longer service the truck or deal with me.i even asked the dealer if they would take the truck back in trade for another vehicle, as i really need a reliable truck.they told me that they would not take the truck in trade or in any other manner and i needed to take the matter up with chevrolet.

At first, truck showed tps alarm ,then stability alarm ,next ithad the headlights cut out on the highway at night @ 70 mph for 15-30 seconds. It has shown these problems separately and simultaneously at different times. Finallyit manifested a new symptom i would intermittently not crank the engine over even though the battery was at full charge. After repeated trips to the dealer(they said they could not reproduce the problem) with no effect or improvement, a call to chevrolet netted a case number #71-1257538002. As a result of this call( i feel) work was restarted on the vehicle. As of today 12/26/13the chevrolet dealerhas now changed the ignition switch. We shall see.information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6).

I keep getting warning. Service stab system.what i have read on line is that this is a gm computer problem that gm doesn't want to fix

As long as the security light flashes the truck will not start. I take off the negative clamp off the battery an wait10 minutes it will start. If i use the remote to lock the truck every third time the truck will not start. An some times it does it more than that.so i don't use the remote. Stationary. This happens several times a week.

The contact owns a 2012 chevrolet colorado. The contact stated that an abnormal whistling noise was heard and grew worse over the past months. The vehicle was taken to an independent mechanic where it was diagnosed that the exhaust manifold had a crack down the middle and needed to be replaced. The vehicle was not repaired. The dealer was not contacted. The manufacturer was notified. The approximate failure mileage was 118,000.

Will not start have to take off- post from battery then 10 minutes before it starts. The security light flashes for the 10 minutesbefore it starts.. Ems needs replaced.if i lock the truck after the 3 time it startsthis s(xxx). 2012 chevy. Colorado. It's not the key or switch.

The contact owns a 2012 chevrolet colorado. The contact stated that while driving 20 mph, the vehicle stalled. The contact stated that he coasted to the side of the road and restarted but the engine failed again. The contact had the vehicle towed to the dealer for diagnosis. The dealer advised the contact that an unknown sensor needed to be replaced. The vehicle was repaired but when the vehicle was test driven, a fire originated from the engine. The vehicle was not destroyed. There were no injuries reported. The manufacturer was notified but the contact had not received a response. The failure mileage was 380.

Was traveling south going through an intersection on a green traffic light when another vehicle traveling north in a left turn yield on green, when the designated green arrow is not illuminated, turned in front of me and we collided.the air bags did not deploy on either side. Driver and front passenger in vehicle traveling south sustained injuries and transported to hospital in ambulance.

The contact owns a 2012 chevrolet colorado. When the vehicle was started, an unknown warning indicator flashed. The contact had to remove the battery cable, wait a few minutes, reinstall the battery cable, wait an additional few minutes, and then start the vehicle for it to resume normal operation. The contact had not taken the vehicle to a dealer or mechanic to have the vehicle serviced. The manufacturer was not aware of the defect. The vehicle had not been repaired. The failure mileage was 47,000. *dtthe consumer stated he needs a paper copy of evoq.

The contact owns a 2012 chevrolet colorado. While driving approximately 5 mph the contact heard a popping sound coming from the exhaust system. The vehicle was taken to the dealer for diagnostics. The technician advised that the muffler would have to be replaced. The muffler was replaced but the failure continued. The vehicle was not repaired. The vin was not available. The approximate failure mileage was 2,500. ...updated 07/19/12the consumer stated the vehicle would mis-fire when the engine was cold, and it would lose power after it warmed up. Updated 02/06/13

2012 chevrolet colorado.consumer writes in regards to transmission issues.the consumer stated the vehicle would not start. The vehicle was towed to the dealer. When the consumer called the dealer a couple of days later, he was informed the issue was the transmission. The next week, the consumer was informed, the parts replaced in the transmission were not issue, and after further investigation,the issue was a loose timing chain tensioner. Later in the week, he was informed that the engine was damaged and there may have been a spun bearing that caused the issues. The consumer was then informed the engine needed to replaced, but it would take couple of days to get an approval for the replacement.the authorization finally came through and the dealer proceeded to replace the engine the following week.the consumer was told he could pick the vehicle up on june 1st. However, they wanted to put some additional miles on the truck to confirm everything was in specification.when the consumer arrived at the dealer, he was informed the vehicle overheated and had to be towed back to the dealership.the dealer had the vehicle for two weeks. The consumer stated the vehicle continued to have problems. He stated the truck would idle in a rough manner , and the check engine light illuminated.the consumer stated he checked the codes on the vehicle, and determined they were transmission related. The consumer went to another dealer, who diagnosed the problem as a wiring harness issue and some crimped seals from the first dealerships workmanship. The vehicle was properly repaired and returned to the consumer.

The contact owns a 2012 chevrolet colorado. While driving 60 mph, the contact noticed that the steering wheel became difficult to maneuver and the battery warning indicator illuminated. The contact pulled the vehicle over to the side of the highway and opened the hood to find that the idler pulley bracket had fractured, which also caused the belt to fracture. The vehicle was taken to the dealer (dick shirley chevrolet, 2616 alamance rd, burlington, nc 27215) where it was confirmed that the idler pulley bracket fractured and the belt. The manufacturer was notified of the failure and informed the contact that they would be unable to assist with the repairs.the vehicle had not been repaired. The failure mileage was 85,000.

The contact owns a 2012 chevrolet colorado. While driving approximately 5 mph the contact heard a popping sound coming from the exhaust system. The vehicle was taken to the dealer for diagnostics. The technician advised that the muffler would have to be replaced. The muffler was replaced but the failure continued. The vehicle was not repaired. The vin was not available. The approximate failure mileage was 2,500. ...updated 07/19/12the consumer stated the vehicle would mis-fire when the engine was cold, and it would lose power after it warmed up. Updated 02/06/13

The contact owns a 2012 chevrolet colorado. The contact stated that an abnormal whistling noise was heard and grew worse over the past months. The vehicle was taken to an independent mechanic where it was diagnosed that the exhaust manifold had a crack down the middle and needed to be replaced. The vehicle was not repaired. The dealer was not contacted. The manufacturer was notified. The approximate failure mileage was 118,000.

At first, truck showed tps alarm ,then stability alarm ,next ithad the headlights cut out on the highway at night @ 70 mph for 15-30 seconds. It has shown these problems separately and simultaneously at different times. Finallyit manifested a new symptom i would intermittently not crank the engine over even though the battery was at full charge. After repeated trips to the dealer(they said they could not reproduce the problem) with no effect or improvement, a call to chevrolet netted a case number #71-1257538002. As a result of this call( i feel) work was restarted on the vehicle. As of today 12/26/13the chevrolet dealerhas now changed the ignition switch. We shall see.information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6).

The brake light switch needed to be replaced on our 2012 chevy colorado. From review, chevy has recalled colorados of different years for this same issue. I believe the brake light switch recall should be expanded to other years as this problem is occurring in later models than the most current recall year of 2009. We have never had a brake light switch fail on any of our other vehicles. Seems more than coincidental that it would occur on our colorado, when there was a recall previously on the same model, but different manufacture years. Chevy should pay for our repair as well as recall this part for all 2012 colorados. The failure of the brake light switch results in the brake lights not lighting when the brake pedal is pressed. This could result in a dangerous rear end collision as drivers following would be unaware that the brakes were deployed.

2012 chevrolet colorado.consumer writes in regards to transmission issues.the consumer stated the vehicle would not start. The vehicle was towed to the dealer. When the consumer called the dealer a couple of days later, he was informed the issue was the transmission. The next week, the consumer was informed, the parts replaced in the transmission were not issue, and after further investigation,the issue was a loose timing chain tensioner. Later in the week, he was informed that the engine was damaged and there may have been a spun bearing that caused the issues. The consumer was then informed the engine needed to replaced, but it would take couple of days to get an approval for the replacement.the authorization finally came through and the dealer proceeded to replace the engine the following week.the consumer was told he could pick the vehicle up on june 1st. However, they wanted to put some additional miles on the truck to confirm everything was in specification.when the consumer arrived at the dealer, he was informed the vehicle overheated and had to be towed back to the dealership.the dealer had the vehicle for two weeks. The consumer stated the vehicle continued to have problems. He stated the truck would idle in a rough manner , and the check engine light illuminated.the consumer stated he checked the codes on the vehicle, and determined they were transmission related. The consumer went to another dealer, who diagnosed the problem as a wiring harness issue and some crimped seals from the first dealerships workmanship. The vehicle was properly repaired and returned to the consumer.

Was traveling south going through an intersection on a green traffic light when another vehicle traveling north in a left turn yield on green, when the designated green arrow is not illuminated, turned in front of me and we collided.the air bags did not deploy on either side. Driver and front passenger in vehicle traveling south sustained injuries and transported to hospital in ambulance.

The contact owns a 2012 chevrolet colorado. The contact stated that the air bag warning light remained illuminated. The dealer was unable to reset the air bag warning light. Approximately one week later, the vehicle was parked and a loud pop sound was heard from the vehicle as well as the odor of gun powder. The contact discovered that the front driver's side seat belt retractor exploded. The contact took the vehicle to the dealer where it was diagnosed that the seat belt retractor needed to be replaced. The air bag warning light still needed to be reset. The seat belt retractor was replaced, but the failure recurred and blew a hole into the rear driver side door panel. The vehicle was not repaired a second time. The manufacturer was made aware of the failures. The approximate failure mileage was 76,126.

The brake light switch needed to be replaced on our 2012 chevy colorado. From review, chevy has recalled colorados of different years for this same issue. I believe the brake light switch recall should be expanded to other years as this problem is occurring in later models than the most current recall year of 2009. We have never had a brake light switch fail on any of our other vehicles. Seems more than coincidental that it would occur on our colorado, when there was a recall previously on the same model, but different manufacture years. Chevy should pay for our repair as well as recall this part for all 2012 colorados. The failure of the brake light switch results in the brake lights not lighting when the brake pedal is pressed. This could result in a dangerous rear end collision as drivers following would be unaware that the brakes were deployed.

Abs module light gm isn't making the module to fix this issue and has no plans to make more. This means this issue cannot be fixed.

Traction control dash light is illuminated and display states "traction fault service stab sys". Dealer stated there were no codes present and they did not know the cause. Fault occurs before engine crank and is intermittent, happening 8-9 times out of 10.

The contact owns a 2012 chevrolet colorado. The contact stated while driving approximately 35 mph attempting to stop at a traffic light, the brakes failed to stop the vehicle. The vehicle was taken to the dealer. The technician was unable to diagnose the failure. The vehicle was repaired. The manufacturer was notified of the failure. The approximate failure mileage was 14,000.

The parking brake cable running from the foot pedal to the middle of the truck is attached to the frame in such a way that it wore a hole though the rubber casing.this caused the interior metal cable to rust.the interior metal then would not move freely through the rubber casing.while driving the because of bumpy roads would creep upand engage while driving.the truck was purchased in july of 2012, but it only has 23000 mile on it.i called the chevy dealer and he indicated that there was not recall.i had my mechanic repair the brake. I have included three photos.the first is the bill for the replacement of the brake cable.the 2nd is a long view of the part changed.the 3rd is a medium view of the part removed.the 4th is a close up of the problem area.

Abs brakes and stabilitrac lights on dash upon starting, taken to dealer on 11/27/2014, miles 39138, failed again 12/19/2014, miles 39780, and 12/31/2014 for same problem. Truck is still at dealer as of 01/16/2015.after first failure braking was not right, and the truck needs a part that can not seem to be found to date. I believe this truck is unsafe to drive due to the brake issue, and will not keep the truck upon return, but i am fearful that it will be sold to another consumer, and it will be involved in a tragedy.

I was on the freeway going to work at 5:00 am with almost no traffic.a pickup truck in the next lane left of me had a piece of plywood ejected from the bed and was flying through the air towards the front of my pickup.i saw it coming at me and i depressed the brake pedal once but my truck did not slow to avoid it and the plywood destroyed the front nose (grill, lights and all front grill emblems and so forth).it was due to the fact that my truck has had bad brakes since it was brand new.i have taken it to the chevrolet dealer 4 times for repair with no resolution.my truck is at tom benson chevrolet dealership with 8700 miles on it currently since 4/26/2014 and today 4/30/2014 they called me again to say there is no problem with it.they are wrong.i have always had brake problems with this vehicle since 7/28/2012.the brake pedal fades always at a red traffic light.the brakes lose hydraulic pressure always, but the dealer tells me i am wrong.

Popping noise from the front end when turning left or right and applying brakes.come to find out the frame is cracked on both left and right frame rails at the factory welds. This truck has never been in an accident and i'm the original owner. The chevy dealer condemned the truck for safety reasons and said the only repair is to replace the entire frame.

The contact owns a 2012 chevrolet colorado. While driving 60 mph, the contact noticed that the steering wheel became difficult to maneuver and the battery warning indicator illuminated. The contact pulled the vehicle over to the side of the highway and opened the hood to find that the idler pulley bracket had fractured, which also caused the belt to fracture. The vehicle was taken to the dealer (dick shirley chevrolet, 2616 alamance rd, burlington, nc 27215) where it was confirmed that the idler pulley bracket fractured and the belt. The manufacturer was notified of the failure and informed the contact that they would be unable to assist with the repairs.the vehicle had not been repaired. The failure mileage was 85,000.

The contact owns a 2012 chevrolet colorado. The contact stated the steering wheel was extremely difficult to maneuver. The steering wheel would not return to the center after completing a turn. The vehicle was taken to the dealer who replaced the rack and pinion shaft twice and the power steering pump once. The steering continued to fail. The manufacturer was notified who advised the contact that the failure was normal for the vehicle. The vehicle was not further repaired. The failure mileage was 1,550.

2012 chevy colorado extended cab 2x4 i4 engine lt1. The problem is in the steering. The steering is extremely hard turning. The steering does not return to center at more than 30 degrease when after making a turn. When starting out, turn wheel 90 degrease and then proceed forward and the steering wheel will stay in this position and car will just drive in circles.took to andrew chevy had sae certified tek test drive, stated there is a problem make an appointment.andrew called and said it would need a new rack and pinion, replaced. Still all steering is the same. Took to heiser chevy they looked at it and the rack and pinion was leaking oil. Heiser replace rack and pinion still steering not fixed. Two days later power steering pump goes out. Heiser replaced power steering pump. Still remains with steering problem, does not return and really hard to steer. Like a tank. 900 miles, $23,000.00 hmmmm. Chevy customer service useless telling me now that this is the way the truck is supposed to be. Not, owned a 2008 same model never had and issue like this and all good operating vehicle do not steer like this!!! when driving this truck be very aware and ready to return wheel "dangerous". Surely not what i learned in drivers ed, after making the turn let the wheel slide back threw your hands. 51 and some things you never forget...

2012 chevy colorado extended cab 2x4 i4 engine lt1. The problem is in the steering. The steering is extremely hard turning. The steering does not return to center at more than 30 degrease when after making a turn. When starting out, turn wheel 90 degrease and then proceed forward and the steering wheel will stay in this position and car will just drive in circles.took to andrew chevy had sae certified tek test drive, stated there is a problem make an appointment.andrew called and said it would need a new rack and pinion, replaced. Still all steering is the same. Took to heiser chevy they looked at it and the rack and pinion was leaking oil. Heiser replace rack and pinion still steering not fixed. Two days later power steering pump goes out. Heiser replaced power steering pump. Still remains with steering problem, does not return and really hard to steer. Like a tank. 900 miles, $23,000.00 hmmmm. Chevy customer service useless telling me now that this is the way the truck is supposed to be. Not, owned a 2008 same model never had and issue like this and all good operating vehicle do not steer like this!!! when driving this truck be very aware and ready to return wheel "dangerous". Surely not what i learned in drivers ed, after making the turn let the wheel slide back threw your hands. 51 and some things you never forget...

I was on the freeway going to work at 5:00 am with almost no traffic.a pickup truck in the next lane left of me had a piece of plywood ejected from the bed and was flying through the air towards the front of my pickup.i saw it coming at me and i depressed the brake pedal once but my truck did not slow to avoid it and the plywood destroyed the front nose (grill, lights and all front grill emblems and so forth).it was due to the fact that my truck has had bad brakes since it was brand new.i have taken it to the chevrolet dealer 4 times for repair with no resolution.my truck is at tom benson chevrolet dealership with 8700 miles on it currently since 4/26/2014 and today 4/30/2014 they called me again to say there is no problem with it.they are wrong.i have always had brake problems with this vehicle since 7/28/2012.the brake pedal fades always at a red traffic light.the brakes lose hydraulic pressure always, but the dealer tells me i am wrong.

Was traveling south going through an intersection on a green traffic light when another vehicle traveling north in a left turn yield on green, when the designated green arrow is not illuminated, turned in front of me and we collided.the air bags did not deploy on either side. Driver and front passenger in vehicle traveling south sustained injuries and transported to hospital in ambulance.

Popping noise from the front end when turning left or right and applying brakes.come to find out the frame is cracked on both left and right frame rails at the factory welds. This truck has never been in an accident and i'm the original owner. The chevy dealer condemned the truck for safety reasons and said the only repair is to replace the entire frame.

Shut off, do not lock, try to start and the car with the padlock is lit up and i cannot start the pickup. Hit lock, unlock, still won't get rid of car/padlock light..get out hit lock, unlock. Still won't get rid of car/padlock light.i have to keep doing this until the light goes off so i can start the pickup.has happeded twice in the last 4 weeks.

The contact rented a 2012 chevrolet colorado. While driving approximately 70 mph, the vehicle continued to accelerate at the same speed as the contact removed his foot from the accelerator pedal. The vehicle decelerated once the contact applied the brakes. The vehicle rental company was advised of the failure and advised the contact that the vehicle would be further inspected to assess any possible failures. The vehicle was not repaired. The approximate failure mileage was 13,350.




Read more




© 2024 All rights reserved