We found the following complaints for DOREL EDDIE BAUER 3-IN-1 (Unknown)
Read complaints for DOREL EDDIE BAUER 3-IN-1 (Unknown)
When i went to change the height of the harness on my car seat i followed the instructions which said "from the front , insert the harness strap, harness retainer, buckle plate, and "s" clip through the shoulder harness slot in the seat pad and shell."i was able to get all of the pieces through the shell, the buckle plate is extremely difficult to get through the hole in the shell, requiring an extreme amount of force.when i tried to put all of the pieces back through the shell i was unable to put the buckle plate back through.we tried positioning the buckle plate every which way we could but were still unsuccessful.we even tried to hammer it back through the hole in the shell.the harness plate is wider than the hole in the shell.i tried to call the manufacturer but they were at lunch until 12:30pm. 10:30am my time.my daughter had a doctor's appointment so we had to cut the plastic some to get the buckle plate back through.i called the manufacturer and tried to explain to them what had happened but they just continued to say that the buckle plate would fit through if i turned it the correct way.the manufacturer didn't do anything with my concern since we damaged the seat.
This is in regards to the eddie bauer adventurer travel system that my husband and i purchased at sears in february. This is for the car seat only. The numbers on the seat are as follows: 11/20/09 gbib, and the model number is ic-048 aai. The handle on this car seat is very loose. It continues to get worse. The more it is carried by the handle, the more loose it gets. I have sent an e-mail to the dorel juvenile group and i am waiting for a reply. There have been no repairs or replacement parts sent to me yet.
Child car seat does not recline property and my child's head is not supported. When i make a turn her head falls from one side to the other. When she falls asleep her head hangs with no support. I feel that if i was in an accident her life could be endangered and something must be done about this problem.
Dt*: the contact owns a safety first child safety seat manufactured by dorel juvenile group.the model number was not currently available.the a-lock does not lock on the center adjustment strap of a child safety seat.
Child seat has a crack at the top of the tray shield and the recline adjuster button does not stay in place.*mr*la
Consumer seeks recall information for her model number car seat .
The center strap on an eddie bauer branded car seat made by dorel juvenile group (model 22790wpr) frayed after less than a year of part-time use.dorel is taking back the seat for qa but the tightening mechanism is suspiciously hard to use on their carseats in general (when a child is present only) and thus may be a potential failure risk for the average consumer.
The contact owns a dorel juvenille group eddie bauer 3-in-1 child seat.the contact stated that the metal clips thats used to tighten the straps would not hold the child securely into the seat.in addition, the contact stated that the metal clip would get caught which prevented the child from being restrained properly.the manufactuer advised the contact to return the child seat.as of march 10, 2008, the contact had not returned the child seat.(related vehicle information: model year=2008, make=ford, model=fusion)updated 3/25/08
Dt*: the contact stated the harness buckle that goes over the chest comes unsnapped.this is an eddie bauer child safety seat, model # 22-864-mrc.the manufacturer date is: 7-14-05.
-put child in carseat and shoulder restraint did not work properly.-called company, was told the carseat was recalled, but i was never notified even though we did call co. At other times and did send in cards for 2 seats-wanted to purchase 2 new seats at cost was told they would not give me something for nothing and sent me repair kit. -there was a problem with the strap used to pull the shoulder straps tight.-once i received parts i called company, i told them i did not feel comfortable with the solution to the problem and felt it was not safe i again offered to purchases to two new seats at cost, i just recently purchased 2 seats from the company and at this point in time has purchased 6 seats from this company, i have 4 children.-i spoke with someone who is suppose to be knowledgeable about this issue and she said "this would fix the problem" i currently had two of the recalled seats and needed to fix both.-after using seats for about a week i was away in watkins glen ny at a race on july 4th at 8 pm at night in the middle of nowhere and the strap system complete broke.-now what do you do with a child who weighs about 25lbs and no carseat and no store for atleast 1 hour away and you are 3 hours from home. We had use the shoulder strap, thank god seat had the latch system-i called the company at this point furious, i was then sent 2 new seats for free because i told them now i want something for nothing and my husband was ready to call a lawyer.-i was dissatisfied with the seats i received they were not the quality i purchased in the past, i told them that, there is no way they are as safe as the one i had, i should have had the option to get the quality of seat that i have purchased from this specificco. The previous 6 times.i don't have all the specific on the seat, after thinking about it recently i thought i should report this, contact me and i can try to contact manf. They should have it on record. Fill out to best of knowledge.
-the contact stated that when making a turn ithe safety seat will flip over. She has to hold the safety seat while turning the vehicle in order to reach the seat.while driving the contact must position the seat as far back as possible so that she may prevent the seat from flipping over. Since the child weas only 1 month old the childcould not be placed in the front seat.eddie bauer comfort #22630lkm. Needed to register car seat-702-807-9025.updated
The contact owns a dorel trailmaker travel system (n/a). The contact stated that while parked, the child managed to place her right hand in the opening near the rear of the seat where the seat belt of the vehicle goes through to secure the child. The child sustained cuts to her right hand. The manufacturer was contacted and provided the contact with a replacement seat. The contact was not satisfied the replacement seat. The contact stated that the child seat was not being used.
Foia request for document pertaining to an investigation into a cosco eddie bauer car seat model number 02-c49-ebl-hb2b. *ph (nar)
Dt*: the contact stated that the metal piece on the back of the child safety seat where the seat belt loops through had broken.the manufacturer informed the contactthat there was a recall on the child safety seat, nhtsa campaign id # 05c003000; child seat: harness , but the free in-home remedy kit offered would not fix the problem because the broken metal piece is not part of the recall.the contact believes the metal piece broke due to the poor integrity of the failed part noted in the recall.
Dt*: the contact stated while driving 15 mph on normal road conditions and using the child safety seat in the rear facing position, the child seat reclined. The reclining was worst when the vehicle made turns. The base of the child seat was firmly buckled but still slid around. The manufacturer has not been contacted. .manufacturer: dorel juvenile group, eddie bauer edition, model # 22-630 and dom: 2006.
Dt*:the contact stated the rear facing infant carrier handle was loose.upon initial inspection by the contact, it was determined the handle screws needed tightened.additionally, with or without the child restrained in the infant seat, the base slid from side to side without warning.the manufacturer was alerted.the child safety seat was a dorel juvenile group, model eddie bauer, # 22-630fmt, and the date of manufacturer was february 2, 2006.
Dt*: the contact stated while driving 15 mph on normal road conditions and using the child safety seat in the rear facing position, the child seat reclined. The reclining was worst when the vehicle made turns. The base of the child seat was firmly buckled but still slid around. The manufacturer has not been contacted. .manufacturer: dorel juvenile group, eddie bauer edition, model # 22-630 and dom: 2006.
Dt*: the contact stated the child seat base was unstable causing the seat to tip.the child fell out of the child seat when the incident occurred.no injuries were sustained. Manufacturer:dorel juvenile group. Make:eddie bauer. Model:22-630. Date of manufacture:09/28/05.
When pulling into driveway child seat came out of the base while child being restrained. No report of injury. The cause as why this happened was undetermined.
Dt*: the contact stated the child safety seat would not lock into the base properly and the harness buckle was difficult to secure or release the occupant.the manufacturer was contacted and was willing to replace the parts if the contact sent the fabric and straps, leaving a useless child safety seat until the new parts arrived.manufacturer: dorel juvenile group.make: eddie bauer.model: 22- 625 mac gb1b.build date: 1/27/2005
- child seat's frontbuckle does not stay latched. The child easily pulls the latch out and comes out of the car seat. Dorel juevinle incorp installed the seat, which was front facing. The safety seat was purchaced at target in fairborne, oh or beaver creek, oh.model 22-858-shl
Dt*:the contact stated that the dorel juvenile group, eddie bauer edition child safety seat, model # 22-630 bal, fell to the left side when the vehicle made a turn.the child safety seat was tightly strapped into vehicle using the safety belts.the manufacturer was notified, who offered to send out a new base for the seat.
The contact owns a dorel eddie bauer 3-in-1 child seat.the contact noticed that when the child seat was placed on the base, it was not sturdy or secure.she also noticed that the screws in the handle were loose when it was lifted.the handle shook and wiggled.the contact took the safety seat to a local fire department and they determined that it was unsafe to use.dorel offered the contact a repair kit, but that did not correct the failure.
- the contact'seddie bauer cohert, model# 22630fmt child safety seat's trim screwfell onto the seat.the contact replaced the trim screw, and was unaware of the replacement kit that was available. Advised the contact per the recall #06c005000on nhtsa website to call djg's toll free at 877-229-1374 so that a kit may be sent to the contact.the contac also filed a complaint because the child safety seatgould not be secured to its base.the contact stated that she followed the installation instructions, but the seat cannot be secured properly, and wiggled back and forth, and side to side.
- the contact stated that the eddie bauer #22-630 child safety seat latch does not stay in the locked position when the vehicle makes a turn. The contact states that it doesn't matter how the seat is installed, the safety seat it will not hold.
- the contact stated that while driving 30 mph she slowed down to make a left turn, and the car seat completely fell to the left side.the car seat and the base were still secured with a seatbelt.this failure has occurred on three (3) separate occasions.
The contact owns a dorel eddie bauer 3-in-1 child safety seat, model number: gb1a3, manufactured september 29, 2011. The contact stated that the child seat base release mechanism would not function. The failure recurred intermittently. The manufacturer was not notified of the defect. The child seat had not been replaced.
Infant seat would not disengage from base.
Dt*:the contact stated the rear facing infant carrier handle was loose.upon initial inspection by the contact, it was determined the handle screws needed tightened.additionally, with or without the child restrained in the infant seat, the base slid from side to side without warning.the manufacturer was alerted.the child safety seat was a dorel juvenile group, model eddie bauer, # 22-630fmt, and the date of manufacturer was february 2, 2006.
The contact stated that her eddie bauer model# 22-625ars-og2b, child safety seat detached from the base with the seat in place and hit the back of the passenger seat. The contact had no previous failures with the child safety seat; however she is concerned of the safety risk involved.
Dt*:the contact stated one of the screws on the carrying handle of the child safety seat fell out and landed in the seat.upon inspection of the handle, the contact determined that the other 5 handle screws had loosened extensively.
The contact owns an eddie bauer, model# 22-630.while lifting the child safety seat the handle slipped backwards which caused the child safety seat to fall forward with the child in the seat.the lock on the child safety seat didn't engage.
Dt*:the contact stated while using the child safety seat as a carrier the handle did not lock properly into place and the child was ejected onto the floor.the harness was buckled, but was only around the child's arms.mouth injuries were sustained, and the child was in route to the hospital. The manufacturer has not been contacted.the child safety seat is an eddie bauer, model #22-625-glc and was manufactured 3/5/2005. Updated05/30/2006.
Dt*:the contact stated that the screws on the handle for the infant child safety seat are coming out.one screw was in the carrier where the baby is secured.the child safety seat is an eddie bauer 22-630-hpn that was manufactured on october 7, 2005.
Dt*:the contact stated the rear facing infant carrier handle was loose.upon initial inspection by the contact, it was determined the handle screws needed tightened.additionally, with or without the child restrained in the infant seat, the base slid from side to side without warning.the manufacturer was alerted.the child safety seat was a dorel juvenile group, model eddie bauer, # 22-630fmt, and the date of manufacturer was february 2, 2006.
The contact owns a dorel eddie bauer 3-in-1 child seat.the contact noticed that when the child seat was placed on the base, it was not sturdy or secure.she also noticed that the screws in the handle were loose when it was lifted.the handle shook and wiggled.the contact took the safety seat to a local fire department and they determined that it was unsafe to use.dorel offered the contact a repair kit, but that did not correct the failure.
Dt*:the contact stated the screws that hold the handle on the child safety seat came loose and fell into the child safety seat.the child was then able access the screws which resulted in the rest of the screws becoming loose.the manufacturer was alerted and theyprovided a new seat.the seat manufacturer is doral juvenile group, model eddie bauer 22-630-mrc, date of manufacturer is july 30, 2005.
Dorel juvenile group model # 22625edg,the straps on the safety seat will not stay latched.the childusing the seat was an infant, and the mother found him unsecured on several occasions.contacted the manufacturer, who statedit waspossibile that thestraps were the wrong ones, and they will send new ones.model 22625edg
The chest clasp/harness buckle broke on the cosco child seat. *mr the harness buckle broke during normal use. (cosco dorel juvenile group/model# 02537) *sc
Dorel juvenine group, model # 22-625cdg, the harnessbuckle would not stay fastened while the child was riding in the car seat.it has gotten to the point where the child had to be secured with a safety pin.
The harnessbuckle would not stay fastened while the child was riding in the car seat.it has gotten to the point, where the child has to be secured with a safety pin.
If the infant moves too much they straps become unsecured or loose.manufacturer sent longer straps, but this did not not help.
The seat back strap became unlatched on several occasions.
After securing the infant,the buckle cameloose.the consumer had noticed this on several occasions.
Dt*: the contact stated the child safety seat would not lock into the base properly and the harness buckle was difficult to secure or release the occupant.the manufacturer was contacted and was willing to replace the parts if the contact sent the fabric and straps, leaving a useless child safety seat until the new parts arrived.manufacturer: dorel juvenile group.make: eddie bauer.model: 22- 625 mac gb1b.build date: 1/27/2005
The contact owns a dorel eddie bauer ebadj booster seat, model #22880/mpta man (na).the seat was manufactured on november 5, 2007.while driving at an unknown speed, the contact reached down to pick up her phone and the vehicle swerved to the side.she overcorrected the vehicle and it flipped over twice down into a culvert and struck a tree head on.the chest buckle snapped on the booster seat and threw her 19-month old child onto the floor.the child suffered knee, neck, and head injuries.the manufacturer was not notified.a police report was filed.the purchase date was unknown.
When i went to change the height of the harness on my car seat i followed the instructions which said "from the front , insert the harness strap, harness retainer, buckle plate, and "s" clip through the shoulder harness slot in the seat pad and shell."i was able to get all of the pieces through the shell, the buckle plate is extremely difficult to get through the hole in the shell, requiring an extreme amount of force.when i tried to put all of the pieces back through the shell i was unable to put the buckle plate back through.we tried positioning the buckle plate every which way we could but were still unsuccessful.we even tried to hammer it back through the hole in the shell.the harness plate is wider than the hole in the shell.i tried to call the manufacturer but they were at lunch until 12:30pm. 10:30am my time.my daughter had a doctor's appointment so we had to cut the plastic some to get the buckle plate back through.i called the manufacturer and tried to explain to them what had happened but they just continued to say that the buckle plate would fit through if i turned it the correct way.the manufacturer didn't do anything with my concern since we damaged the seat.
Dorel juvenile group eddie bauer model: # 22-625-mca, dom01-07-2004.while driving driver noticed that the shoulder straps unbuckled on their own.consumer will contact the manufacturer in the near future.
Dt*: the contact stated the harness buckle that goes over the chest comes unsnapped.this is an eddie bauer child safety seat, model # 22-864-mrc.the manufacturer date is: 7-14-05.
The contact owns an eddie bauer prospect safety seat.the model number is 2280-mtt.the manufacturer date is 01/01/07.the contact stated the buckle on the safety seat is too bulky which makes it physcially impossible for the child to be secured in the safety seat.the contact tried to place the seat in three different vehicles.the manufacturer provided a kit to the consumer. Updated 03/30/07.
- the contact owns a 2006 dorel juvenile eddie bauer child safety seat model 22-630, and stated that the harness strap did not go downfar enough to attach into the buckle, which caused the child to be strapped in too tight. The safety seat was manufactured on 02/26/06.the contact can provide pictures if needed.returned usps, 2nd attempt made04/12/07 failed .* lj
The contact owns a 2003 cosco eddie bauer, model number 22-720 child seat (na).the contact stated that the seat has safety straps attached to the bars.the bars are attached to the base of the seat.she stated that the bar on the left side completely detached from the seat without warning.after inspecting the seat, the contact noticed that the child could no longer be properly secured in the seat.the contact filed a complaint with the manufacturer.the purchase date was unknown. Updated 12/13/07 updated 12/13/07
-put child in carseat and shoulder restraint did not work properly.-called company, was told the carseat was recalled, but i was never notified even though we did call co. At other times and did send in cards for 2 seats-wanted to purchase 2 new seats at cost was told they would not give me something for nothing and sent me repair kit. -there was a problem with the strap used to pull the shoulder straps tight.-once i received parts i called company, i told them i did not feel comfortable with the solution to the problem and felt it was not safe i again offered to purchases to two new seats at cost, i just recently purchased 2 seats from the company and at this point in time has purchased 6 seats from this company, i have 4 children.-i spoke with someone who is suppose to be knowledgeable about this issue and she said "this would fix the problem" i currently had two of the recalled seats and needed to fix both.-after using seats for about a week i was away in watkins glen ny at a race on july 4th at 8 pm at night in the middle of nowhere and the strap system complete broke.-now what do you do with a child who weighs about 25lbs and no carseat and no store for atleast 1 hour away and you are 3 hours from home. We had use the shoulder strap, thank god seat had the latch system-i called the company at this point furious, i was then sent 2 new seats for free because i told them now i want something for nothing and my husband was ready to call a lawyer.-i was dissatisfied with the seats i received they were not the quality i purchased in the past, i told them that, there is no way they are as safe as the one i had, i should have had the option to get the quality of seat that i have purchased from this specificco. The previous 6 times.i don't have all the specific on the seat, after thinking about it recently i thought i should report this, contact me and i can try to contact manf. They should have it on record. Fill out to best of knowledge.
The contact owns an eddie bauer 3-in-1 convertible child seat, model number 22-758-kgs 12/29/2009 which was rear-facing. The contact stated that the back of the harness belt was torn. The contact had not spoken with the manufacturer at the time of the complaint.
The contact owns a dorel eddie bauer deluxe 3-in-1 child seat, model 22-758-hid.the seat was manufactured on september 29, 2007.when the contact was placing the baby in the child seat, she noticed that the harness (straps) were shredding.the manufacturer took a report and stated that they could send new straps.the contact does not want new straps.she wants the manufacturer to send a new seat because the straps may fit incorrectly.the purchase date was unknown.
- the contact stated thatchildseat dorel model# 22-720 edge harness came apart.while removing the child from thechild seat and raising the harness the arm came loose.the contact stated that the childseat that holds the harness together tore away from the seat.the contact stated that she had no prior indication that the seat was unstable.
The center strap on an eddie bauer branded car seat made by dorel juvenile group (model 22790wpr) frayed after less than a year of part-time use.dorel is taking back the seat for qa but the tightening mechanism is suspiciously hard to use on their carseats in general (when a child is present only) and thus may be a potential failure risk for the average consumer.
I had my car seat checked by a state patrolman and he was concerned about the way the straps that go over the legs secure to the seat.he was able to just pull them out and if i was to get into a wreck and they came loose my child could break her neck and it could lead to death.this is very concerning and he felt that this should be looked into.it is an eddie bauer seat made by the dorel juvenile group, model # 22-880-hpn and the mfg: l#18c133604 12/29/05.
Dt*: the contact stated that the metal piece on the back of the child safety seat where the seat belt loops through had broken.the manufacturer informed the contactthat there was a recall on the child safety seat, nhtsa campaign id # 05c003000; child seat: harness , but the free in-home remedy kit offered would not fix the problem because the broken metal piece is not part of the recall.the contact believes the metal piece broke due to the poor integrity of the failed part noted in the recall.
The harness on the child seat was defective.the consumer had found the child unsecured.22-625 mac.
Child seat harness straps are defective, and the manufacturer admits that there is a problem.the child is continuously unsecured in the seat.manufacturer wants to replace one defective seat with another one.
The latch system was defective.the infant has been unsecured in the vehicle numerous times, once placed into the seat, motherdiscovered the infant latch was not secure.
The shoulder straps loosened and became detached.theseat was takento dealer for replacement.after replacing the seat with the same model the straps were doing the same thing. Manufacturer was sending new straps.however,consumer was concerned.
Dorel juvenile group model # 22-265gdc, the infant seat has black dye coming from the material onto the infant and his clothing.the seat was just purchased.*
The contact owns a dorel eddie bauer 3-in-1 child seat.the model number is 22-88-hpn.when the contact washed the seat cover for the first time, it ripped along the sides where the seat belt is adjusted.she will notify the manufacturer to request a replacement.
Dt:dorel juvenile group, model # 22-130-wal, dom 02-03-2005. Contact statedthat on 7-19-05her grandson got his knee burned because the shield assembly did not have enough cover on the underside,resulting in plastic laying on his knee, andresulting in a burn to his knee. The doctor thought at first it was a third degree burn.butcurrently he maintaineditwas a seconddegree burn. The child was handicapped with cerebral palsy. Manufacturer; dorel juvenile group, told consumerthey should have parked under a tree . Dorel juvenile said their engineers had looked into this and there was nothing else they could do.
Dt*:the contact stated that the fabric on the head restraint of the child safety seat ripped.some of the padding fell out of the tear, causing the head of the child to sit improperly on the head restraint.
Dorel juvenile group model: 22-130-wal dom : 09-24-2004.while removing the car seat from the vehicle the shield broke.the cause has not been determined at this time.consumer will contact the manufacture in the near future.
Dorel juvenile group model# 01750mac dom 01/07/2004.the consumer noticed that the harness straps unbuckled.the consumer contacted the manufacturer, and was informed that theharness strap needed to be replaced.however, the problem still occurred.the straps loosened when the consumer placed the child in the child seat and would sometimes occur when the consumer would take the child out of the child seat after going for a ride. *sc
The harness on the child seat will not stay together to secure the infant.while traveling the harness became unlatched 5 times.contact was made with the manufacture and the consumer has been instructed to send the seat back.
The toddler is able to unbuckle and get out of the 5 point harness straps.this leaves the toddler un restrained in the event of an accident. Please provide the model number and manufacturing date.*la
The harness keeps coming loose.infant has been placed in the infant seat, and found it unsecured.contact to be made with the manufacturer.
Straps on eddie bauer 22-625-edg child seat do not stay latched in the back.*mrthe manufacturer told the consumer they would send thicker straps.
The shoulder straps loosened and became detached.theseat was takento dealer for replacement.after replacing the seat with the same model the straps were doing the same thing. Manufacturer was sending new straps.however,consumer was concerned.
The seat back strap became unlatched on several occasions.
Foia request for document pertaining to an investigation into a cosco eddie bauer car seat model number 02-c49-ebl-hb2b. *ph (nar)
Read more
