We found the following complaints for DOREL 02-537 (Unknown)
Read complaints for DOREL 02-537 (Unknown)
I am an experienced cpst who assisted a soon to be mother with the installation of a maxi-cosi mico infant seat and basetoday.release of infant seat from basewassignificantly problematic.the base released only when fingers were pressed up under the release bar at the same time it was being "pulled out". Simply pulling the release bar in an outward direction was not sufficient to release the carrier from the base.re-connection to base seemed even more problematic as the carrier often failed to engage with the base.. On 2 of 5 separate attempts i made to connect the carrier to base the base ....the carrier would not latch on to the base attachment hardware because the base attachment hardware was "locked"in the closed position. When the attachment hardware is locked and closed it obstructs the carrier rods from attaching to the base hardware as intended.my concern is that this could routinely result in the carrier not properly being secured to the base.since i am unable to enter the model and make of the seat with the drop down boxes i will enter it below:doerl juvenile groupmodel# 22-371-oregb1b 11/19/07a blue circular sticker is noted on the product registration card (similar to what i have seen in recalls on other products).i spoke with dorel / maxi-cosi division today regarding this complaint and was assured that they would pass the concern on to the engineers.
I am an experienced cpst who assisted a soon to be mother with the installation of a maxi-cosi mico infant seat and basetoday.release of infant seat from basewassignificantly problematic.the base released only when fingers were pressed up under the release bar at the same time it was being "pulled out". Simply pulling the release bar in an outward direction was not sufficient to release the carrier from the base.re-connection to base seemed even more problematic as the carrier often failed to engage with the base.. On 2 of 5 separate attempts i made to connect the carrier to base the base ....the carrier would not latch on to the base attachment hardware because the base attachment hardware was "locked"in the closed position. When the attachment hardware is locked and closed it obstructs the carrier rods from attaching to the base hardware as intended.my concern is that this could routinely result in the carrier not properly being secured to the base.since i am unable to enter the model and make of the seat with the drop down boxes i will enter it below:doerl juvenile groupmodel# 22-371-oregb1b 11/19/07a blue circular sticker is noted on the product registration card (similar to what i have seen in recalls on other products).i spoke with dorel / maxi-cosi division today regarding this complaint and was assured that they would pass the concern on to the engineers.
Dt*: the contact stated while taking the child safety seat out of the vehicle, the handle was observed to be loose.the child safety seat handle could detach resulting in potential injuries to the child who is only 12 pounds.the problem has gradually worsened over time. Manufacturer: dorel juvenile group model#: 01938swb dom:01/22/05
The contact owns a 2008 dorel forward facing child seat, model number 22145-bvl (na).the seat was manufactured on april 2, 2008.while the contact's child was positioned in the child seat in the rear of the vehicle, the buckle release mechanism failed.the contact was concerned of the safety risk involved.the purchase date was unknown.
- the contact called regarding a doral safety seat, model number is 22012-paw.the manufacturing date was 9/25/06.the contact was not allowed to transport anew born in the seat from the hospital becausebuckle was too low on the seat.the buckle neededto be up towards the infant's hip.
Dt*: the contact stated that the latch belt assembly of the rear facing infant seat failed, and the buckle released by itself. When the buckle released so did the shoulder harnesswhich caused the child fall to the ground. The child incurred severe injuries. The incident occurred when the infant seat was being removed from the vehicle. The vehicle was parked and the infant seat was located on the rear left side of the vehicle. There were no warnings signals prior to the incident. A police report was taken. The manufacturer has not been contacted. Dorel juvenile group, model 22391, built on 02/10/2006.
The contact owns a dorel alpha omega model 22-180-wal mfr # a01b001090 date of manufacturing 04-5-04.the contact stated that the plastic part on each side of car seat in which the straps got through has fell off.therewas no support and the seatwas unsafe and unable to be used.
Dt*: the contact stated that the latch belt assembly of the rear facing infant seat failed, and the buckle released by itself. When the buckle released so did the shoulder harnesswhich caused the child fall to the ground. The child incurred severe injuries. The incident occurred when the infant seat was being removed from the vehicle. The vehicle was parked and the infant seat was located on the rear left side of the vehicle. There were no warnings signals prior to the incident. A police report was taken. The manufacturer has not been contacted. Dorel juvenile group, model 22391, built on 02/10/2006.
No foam padding from the waist down to the child's feet, plastic protruding under rear of child bottom causing a lot of discomfort.changed from infant car seat to this car seat and child continually screamed while in car seat, i just thought she didn't like the change in car seats, after weeks of this i started feeling around in the car seat and felt plastic pieces protruding up around where her bottom is and no foam padding from the waist down.she had been sitting on the hard plastic and the plastic poked her continually.
The contact owns a dorel 02-537 child restraint.the contact stated that the seat is rarely used and the straps and springs have failed.the manufacturer stated that the warranty expired and advised the contact to cut the straps, dispose of it, or use it with the vehicle seat strap.the manufacturer stated that the baby will be ok.the manufactured date was august 10, 2004.
Read more
