We found the following complaints for COMFORT SPORT 8637 AZC (Unknown)
Read complaints for COMFORT SPORT 8637 AZC (Unknown)
When buckling my 2 year old into her graco comfortsport car seat the restraint fails to tighten on one of the shoulders. I then have to take her out and try to rethread the restraint harness which does not always work therefore she is not secure in the seat.
On 1/19/07, i attepted to raise the shoulder straps on my son's car seat.it was at this time that i realized the both sides of the eps foam had cracked off of the car seat.both of the side pieces that protect his head on either side had cracked.when i attempted to pull the seat cover from the seat both pieces of foam actually fell from the seat.when i call graco to complain the representative told me to wither tape the foam or use elmersglue to re-attach the foam back on to the seat.obviously i found this ridicoulous. When i purchased this seat i was told the foam was for saftey.now graco claims it is for comfort.the model # on the seat is 8639bev and the serial is 110504it wasn't listed as an option .
Graco comfortsportmodel number 8639bev date 02/27/ thefoam insert has broke twice .
The contact owns a graco comfort sport 8637 azc child seat.the contact stated that one of the seat belts has detached from the back of the child seat, where the latch system is located.when she pulled on the seat belt in attempt to recover it, the entire seat belt slid out.she has not yet notified the manufacturer.
Dt:consumer's three year old son is able to unlatch himself from the car seat.
We were driving down the freeway and looked back at our daughter and she had undone the chest clip on her car seat. She's only 21 months old and can undo it and get her arms out of the straps on the car seat.
- the contact stated the harness on the graco comfort sport model # 8434pr6, manufactured 02/10/05 failed.the contact was involved in a car crash on 1/21/07 while driving 20 mph, the vehicle was hit from behind.the safety seat harness came undone at impact and hit the passenger in the head, who was also in a child safety seat. The passenger was injured, but was not ejected from the child safety seat.the contact has a police and ems report.
Graco comfortsport car seat. The rear attachment is a single point attachment for the shoulder straps. When pulling the straps tight it only pulls one of the shoulder straps tight and leaves the other one loose. This problem has been seen on three different cars seats of the same model.model # 8coojrp.
The graco comfort sport seat is unsafe - it tilts to the left where the seat strap enters it.the straps coming over the child are loose on one side tight on the other.not safe at all.i called graco and the lady did not seem to care - she said to re-thread the straps.am i supposed to re-thread everytime we go anywhere?she said well that is how it is.i am very unhappy and the seat is very unsafe.
My daughters(17 months old) can open the chest clip on her graco comfortsport carseat. Model number 8439san 2003-07-02 manf date.this was purchased new, before she was born. Graco solution is to tell me to purchase a new clip from them. I've already paid for one, it's defective. I looked at new graco seats and the clip has changed and is harder to open.
Dt*: the contact stated that there is a problem with the two harness straps on the back of the child seat that were connected to the splitter plates.the webbing was routed through crotch buckle plate and sewn together incorrectly.the manufacturerand a certified child safety technician determined that the child seat be returned to the store where it was purchased. The model number is 8639cos and the product year is 06/07/06.
The contact owns a graco comfort sport 8637 azc model # 8c00tmb.the contact stated that the toddler was able to open the harness tab by pressing the button.the toddler was then able to climb out of the seat seven times with ease while the vehicle was in motion.the manufacturer stated that the close harness tab could be worn out.the seat was purchased approximately two weeks ago.
The two safety straps of the carseat that come down over the shoulders of the child do not remain even- the right side is always much more loose than the left side.this means that in an accident the right side of her body will be thrown forward because it is not being held back snugly.to try to fix this problem you must take the carseat out, adjust the straps, and then attach it back in your car- which is a pain.however, even when we get the straps even and put the carseat back in the car, the first time we use the seat again the straps become uneven.i called graco to report the problem.they said it was very common for this model of carseat to do this.they instructed me to periodically take the carseat out of the car, detach the straps from the splitter, get the straps even and put the carseat back in your car.this what we have been doing all along, but this should not be an issue we have to deal with!when does a busy family with kids have time to take out their carseat every few days and then put it back in again?how many parents don't ever readjust the straps and are endangering their children?besides, if the problem occurs at say a rest stop or the target parking lot, am i just supposed to expect my 1.5 yr old child to sit there unsupervised for 20 minutes while i proceed to take the carseat out, fix the straps and put it back in the car?we have a second carseat for our second car, a britax, and we do not have a similar problem.this program will not let me enter the correct model # for our seat.the model # is 8639cos.
On 2 seperate occasions the shoulder strap on our graco comfortsport has become disengaged from the splitter plate allowing my 14 month old to pull the strap completely through and leaving him unrestrained and able to climb out. We then have to completely remove the seat from our van , reattach the strap and then reinstall the seat.
When buckling my 2 year old into her graco comfortsport car seat the restraint fails to tighten on one of the shoulders. I then have to take her out and try to rethread the restraint harness which does not always work therefore she is not secure in the seat.
Dt:there was a piece of styrofoam padding that broke.the padding was the only buffer on the side of the child seat to keep the child from hitting the shell of the seat.consumer ordered the part on 6-24-05.the manufacturer senta replacement part, but no instructions on how to install it.consumer unable to get in contact with them.the purchase date was2004.
Dt*: the contact was a child passenger safety instructor, and stated the eps foam on the graco comfort sport child safety seat, model # 8639gry was cracking along the head and torso area of where the child would be seated.
Graco comfort sport child safety seat, model # 8433fof, manufacturing dateon 10/12/04styrofoam padding on either side of headbroken away into small pieces.parent stated car seat was not in a crash, and that child did not pick at styrofoam.
I have a graco comfortsport car seat, model number 8636aer, manufacture date 02/25/05. It has an eps (energy absorbing) foam liner.i was putting my child in the seat and brushed up against the side of the seat and the foam snapped off. Since the foam is what absorbs energy in the event of a crash, i knew i needed to replace the seat. I purchased a new seat, but as i was looking, i noticed that the foam was loose on manydifferent brands of seats. Even slight pressure was enough to have the foam at a near breaking point. My concern is that the foam will break on other seats and the parents will continue to use the seat, even though it no longer provides the energy absorption protection that it should
Dt*: the contact stated, while traveling 50 mph at dusk, the vehicle was impacted by another vehicle. The impact was on the passenger side, centered on the support frame between the front and rear doors. The impact forced the front seat into the rear seat causing the collapse of the outer shell of the car seat, killing the infant secured in the car seat.
The contact owns a graco comfort sport 8637 azc.when the child seat was removed from the box, the sticker stated that it was ready to be installed as is.however, the contact stated that the side tether straps would not tighten when they were installed.the manufacturer stated that the straps needed to be switched.the date of manufacture was june 15, 2007.
Read more
